Hydrothermal and ultrasonic processes were used in this study to synthesize a single-atom Cu anchored on t-BaTiO3. The resulting material effectively employs vibration energy for the piezoelectric (PE) catalytic degradation of pollutants. The phase and microstructure of the sample were analyzed using X-ray diffraction (XRD) and scanning electron microscopy (SEM), and it was found that the sample had a tetragonal perovskite structure with uniform grain size. The nanomaterial achieved a considerable increase in tetracycline degradation rate (approximately 95 % within 7 h) when subjected to mechanical vibration. In contrast, pure BaTiO3 demonstrated a degradation rate of 56.7 %. A significant number of piezoinduced negative charge carriers, electrons, can leak out to the Cu-doped BaTiO3 interface due to Cu’s exceptional conductivity. As a result, a single-atom Cu catalyst can facilitate the separation of these electrons, resulting in synergistic catalysis. By demonstrating a viable approach for improving ultrasonic and PE materials this research highlights the benefits of combining ultrasonic technology and the PE effect.
We have intended and preparation of hierarchically absorbent materials were covered with a NiMn2O4 and acts as a catalyst for azo dye degradation. The polyaromatic-based (PA) absorbent compounds were initially constructed by bromomethylated aromatic hydrocarbons which undergo self-polymerization in presence of ZnBr as a reagent and cross linker is bromomethyl methyl ether. The absorbent black materials with a 3D network were prepared by direct carbonization and activation of the as-prepared PA. The hydrothermal method was adapted for the preparation of carbon hybrid material C@NiMn2O4 powder's catalytic activity is effective in reducing p-nitrophenol to p-aminophenol and decolorizing carbon-based dyes like methyl orange (MO), methyl yellow (MY), and Congo red (CR) in aqueous media at 25 °C when NaBH4 is added. UV–visible spectroscopy was used to analyze the dyes' breakdown at regular interval.
The presence of tetracycline (TC) has been detected in the human living environment, and its complex structure makes it difficult to degrade. The green and efficient utilization of electroactivated persulfate advanced oxidation technology for the degradation of tetracycline remains a challenge. In this study, N-doped reduced graphene oxide (N-rGO) was prepared using a hydrothermal treatment method with urea as the nitrogen source. Four different mass ratios of graphene oxide (GO) to urea were synthesized, and the optimal mass ratio was determined through degradation experiments of tetracycline. The N-rGO/EC/PMS three-dimensional electrocatalytic system was constructed, and the influence of the experimental data on TC degradation, such as initial pH, PMS dosage and voltage, was determined. Characterization analysis using scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), and other methods was conducted. The efficient catalytic ability of N-rGO was demonstrated through the generation of hydrogen peroxide ( H2O2) and consumption of peroxymonosulfate (PMS). The superiority of the three-dimensional (3D) electrochemical advanced oxidation process was proposed by combining different systems. Furthermore, the presence of hydroxyl radicals (.OH), persulfate radicals ( SO4 ·−), and singlet oxygen (1O2) was identified using electron spin resonance (ESR) technology. The utilization of N-rGO as a three-dimensional electrode, coupled with the advantages of PMS activation and electrochemical oxidation processes, is a promising method for treating organic pollutants in wastewater.
In this work, we investigated the photo-degradation performance of MnO2-SiC fiber-TiO2 (MnO2-SiC-TiO2) ternary nanocomposite according to visible light excitation utilizing methylene blue (MB) and methyl orange (MO) as standard dyes. The photocatalytic physicochemical characteristics of this ternary nanocomposite were described by X-ray diffraction (XRD), scanning electron microscopy (SEM), tunneling electron microscopy (TEM), ultraviolet-visible (UV-vis), diffuse reflectance spectroscopy (DRS), electrochemical impedance spectroscopy (EIS), photocurrent and cyclic voltammogram (CV) test. Photolysis studies of the synthesized MnO2-SiC-TiO2 composite were conducted using standard dyes of MB and MO under UV light irradiation. The experiments revealed that the MnO2-SiC-TiO2 exhibits the greatest photocatalytic dye degradation performance of around 20 % with MB, and of around 10 % with MO, respectively, within 120 min. Furthermore, MnO2-SiC-TiO2 showed good stability against photocatalytic degradation. The photocatalytic efficiency of the nanocomposite was indicated by the adequate photocatalytic reaction process. These research results show the practical application potential of SiC fibers and the performance of a photocatalyst composite that combines these fibers with metal oxides.
The untreated effluent dropping into the environment from various textile industries is a major issue. To solve this problem, development of an efficient catalyst for the degradation of macro dye molecules has attracted extensive attention. This work is mainly focused on the synthesis of nickel–manganese sulfide decorated with rGO nanocomposite (Ni–Mn-S/rGO) as an effective visible photocatalyst for degradation of textile toxic macro molecule dye. A simple hydrothermal method was used to synthesize Ni–Mn-S wrapped with rGO. The prepared composites were characterized using various techniques such as X-ray diffraction (XRD), high-resolution scanning electron microscopy (HR-SEM), high-resolution transmission electron microscopy (HR-TEM), Fourier transform infra-red spectrometer (FTIR), and ultra violet–visible (UV–Vis) spectroscopy. The photocatalytic performance of nickel sulfide (NiS), manganese sulfide (MnS), nickel–manganese sulfide (Ni–Mn-S), and Ni–Mn-S/rGO nanocomposite was assessed by analyzing the removal of acid yellow (AY) and rose bengal (RB) dyes under natural sun light. Among these, the Ni–Mn-S/rGO nanocomposite showed the high photocatalytic degradation efficiency of AY and RB dyes (20 ppm concentration) with efficiency at 96.1 and 93.2%, respectively, within 150-min natural sunlight irradiation. The stability of photocatalyst was confirmed by cycle test; it showed stable degradation efficiency even after five cycles. This work confirms that it is an efficient approach for the dye degradation of textile dyes using sulfide-based Ni–Mn-S/rGO nanocomposite.
Fe3O4/g-C3N4/TiO2 catalyst has been fabricated using a simple ultrasonic method with high photocatalytic activity. The morphology, structure and optical properties of Fe3O4/ g-C3N4/TiO2 were systematically investigated by a variety of characterization techniques. The optimum degradation conditions were investigated by degrading tetracycline (TC) under visible light irradiation. The results showed that the degradation efficiency was the highest when the initial TC concentration was 5.0 mg/L, the pH value was 11 and the catalyst dosage was 1.0 g/L. After 100 min of visible light irradiation, the degradation efficiency of TC achieved at 73.61%, which was 1.64 and 1.19 times that of g-C3N4 and Fe3O4/ g-C3N4, respectively. Moreover, Fe3O4/ g-C3N4/TiO2 had good stability and recyclability. The results of capture experiments showed that ‧O2 − and ‧OH were the main active species during the photocatalytic process, and a possible photocatalytic reaction mechanism of Fe3O4/ g-C3N4/TiO2 catalyst was proposed. This study provides a new way to improve the photocatalytic performance of g-C3N4, which has great potential in degrading pollutants such as antibiotics in wastewater.
본 논문은 회분식 반응기에서 습식 산화법으로 합성한 칼륨 페레이트(VI)에 의한 난분해성 아조 염료Reactive Black 5의 분해 과정을 연구하는 것을 목적으로 한다. 수용액에서 RB5의 분해는 pH, Ferrate (VI) 투입량, 초기 농도, 수용액 온도 등 다양한 변수의 조건에서 연구되었다. RB5 경우에는 최대 분해 효율은 pH 7.0에서 63.2%가 달성되었으며, 이 실험 조건에서 얻은 kapp 값은 190.49 M-1s-1 으로 나타났다. 온도 또한 가장 중요한 매개 변수 중 하나로 연구되었으며, 그 결과로부터 온도(45°C까지)를 증가시키면 페레이트(VI)에 의한 아조 화합물 염료의 분해 효율이 증가하고, 온도가 45°C를 초과하면 분해 효율이 저하되는 것으로 나타났다.
Pharmaceutical products occurring in freshwater bodies create numerous problems for the water bodies owing to their bio-toxic nature. In order to remove such pharmaceutical pollutants, a novel Er-doped Bi4O5Br2/ g-C3N5 nanocomposite was prepared by one-pot synthesis and applied for the photocatalytic removal process. The Er ions doped on the surface of Bi4O5Br2/ g-C3N5 nanocomposite exhibited 97% degradation of tetracycline in 60 min under visible light irradiation, which is higher than pure g-C3N5 and Bi4O5Br2 photocatalysts. The improved photocatalytic properties are attributed to the outstanding visible light harvesting capacity and quick charge carrier separation efficiency which greatly reduced the recombination rate in the heterojunctions. Based on radical trapping experiments, the •O2 −, h+ and •OH radicals played a prominent role in the photodegradation reactions under visible light. Finally, the ternary Er-doped Bi4O5Br2/ g-C3N5 nanocomposite is effectively recyclable with quite a stable photocatalytic removal rate. This work enables a new perspective on the rational design of rare-earth-based nanocomposites for various pharmaceutical pollutants treatment processes.
Single-atom Pd clusters anchored on t-BaTiO3 material was synthesized using hydrothermal and ultrasonic methods for the effective piezoelectric catalytic degradation of pollutants using vibration energy. XRD patterns of BaTiO3 loaded with monoatomic Pd were obtained before and after calcining, and showed typical cubic-phase BTO. TEM and HAADF-STEM images indicated single-atom Pd clusters were successfully introduced into the BaTiO3. The piezoelectric current density of the prepared Pd-BaTiO3 binary composite was significantly higher than that of the pristine BaTiO3. Under mechanical vibration, the nanomaterial exhibited a tetracycline decomposition rate of ~95 % within 7 h, which is much higher than the degradation rate of 56.7 % observed with pure BaTiO3. Many of the piezo-induced electrons escaped to the Pd-doped BaTiO3 interface because of Pd’s excellent conductivity. Single-atom Pd clusters help promote the separation of the piezo-induced electrons, thereby achieving synergistic catalysis. This work demonstrates the feasibility of combining ultrasonic technology with the piezoelectric effect and provides a promising strategy for the development of ultrasonic and piezoelectric materials.
Bisphenol-A, also known as BPA, is commonly used as a building block for epoxy and polycarbonate plastics. However, it has been recently identified as a major source of water pollution due to its release into the water from plastic products. BPA-based resins can also contaminate the water with high concentrations of BPA, which can enter the water bodies through production units and wastewater discharge. Photocatalysis, particularly the photo-Fenton process, is an effective method for wastewater treatment and degrading pollutants. Titanium dioxide (TiO2) is usually chosen based on its high photocatalytic properties and high performance. However, its wide band gap energy is a major issue for the photocatalytic process. This means that the catalyst can only exhibit high photocatalytic performance under UV-light irradiation and usually requires an acidic pH, which limits its use. In order to address the aforementioned issues, a visible-light photoactive photo-Fenton reaction has been successfully developed to degrade bisphenol A at natural pH using H2O2. The process was highly efficient, achieving complete degradation of phenol in just three hours of visible light irradiation with Cu-MOF. This environmentally friendly Fenton process has the advantage of occurring at natural pH levels with the presence of H2O2, providing a new perspective for efficient degradation. The photocatalyst was characterized using single X-ray diffraction (SC-XRD), powder X-ray diffraction (PXRD), Fourier Transform Infrared Spectroscopy (FTIR), and UV–vis diffuse reflectance spectroscopy (DRS).
Copper, mainly used as a material for outer canister, generates various corrosion products under aerobic and anaerobic conditions in the operational and/or post-closure phases of the deep geological repository. These products could affect performance of engineering barrier system (EBS) through interaction with surrounding bentonite that makes up the buffer and backfill materials. Accordingly, in this study, we suggested research items to be conducted to minimize degradation of EBS due to copper corrosion products, based on the phenomenological review results for copper corrosion mechanisms and interaction between resultant product and bentonite in the deep geological disposal environment. During the post-closure phase, condition in the disposal facility changes form aerobic to anaerobic over time, and thereby, causes and products of copper corrosion vary. Under aerobic condition, copper corrosion is mainly induced by oxygen (O2) in the repository, chloride (Cl-) and carbonate (CO3 2-) ions from groundwater flowing into the facility, resulting in corrosion products such as cuprite (Cu2O), tenorite (CuO), atacamite (CuCl2·3Cu(OH)2) and malachite (Cu2CO3(OH)2). And, copper corrosion under anaerobic condition is primarily due to hydrogen sulfide (H2S) and sulfate (SO4 2-) in groundwater flowing into the facility, leading to formation of chalcocite (Cu2S) and covellite (CuS) as corrosion products. Depending on environment of the disposal facility, copper corrosion products are dissolved and ionized to Cu2+ in groundwater, and subsequently adsorbed on the nearby smectite. Then, it causes a cation exchange reaction with exchangeable cations in the interlayer of smectite. As a result of reviewing the previous experiments, it was confirmed that Cu2+-exchanged bentonite has a slightly reduced basal spacing and swelling capacity. From the results as above, there is a possibility that performance of EBS may be degraded due to copper corrosion products. To minimize its effect of degradation in the domestic facility, items to be further studied are as follows: (a) Method for reducing copper corrosion such as selection of appropriate material and structure for the canister, and (b) How to control dissolution of copper canister product into groundwater through predicting type and ionization process. The results of this study could be directly used to developing design concept of EBS for the domestic disposal facility and to establishing roadmap of future R&D programs.
The Fourth Industrial Revolution and sensor technology have led to increased utilization of sensor data. In our modern society, data complexity is rising, and the extraction of valuable information has become crucial with the rapid changes in information technology (IT). Recurrent neural networks (RNN) and long short-term memory (LSTM) models have shown remarkable performance in natural language processing (NLP) and time series prediction. Consequently, there is a strong expectation that models excelling in NLP will also excel in time series prediction. However, current research on Transformer models for time series prediction remains limited. Traditional RNN and LSTM models have demonstrated superior performance compared to Transformers in big data analysis. Nevertheless, with continuous advancements in Transformer models, such as GPT-2 (Generative Pre-trained Transformer 2) and ProphetNet, they have gained attention in the field of time series prediction. This study aims to evaluate the classification performance and interval prediction of remaining useful life (RUL) using an advanced Transformer model. The performance of each model will be utilized to establish a health index (HI) for cutting blades, enabling real-time monitoring of machine health. The results are expected to provide valuable insights for machine monitoring, evaluation, and management, confirming the effectiveness of advanced Transformer models in time series analysis when applied in industrial settings.
Microphysogobio rapidus is designated as endangered species class I by Ministry of Environment, and its distribution and population have been gradually declining, and it is now limited to the Nam River and some tributary streams of the Nakdong River Watershed. For the restoration of this highly endangered species, it is important to identify the causes of the decline and establish appropriate restoration plans. However, due to lack of basic data and ecological research, most steps are stagnant. Therefore, in this study, we identified the differences in the physical, biological, and sociological habitats between current and past distributed sites through field surveys and literature reviews. As a result of the field survey, there were differences in conductivity between the current and past distributed sites, and fish communities were also showed differences. The literature data also showed that the physico-chemical values of the past distributed sites were generally unfavorable, which generated negative consequences on biological factors. In particular, the effects of urbanization were found to be a major factor affecting the habitat of M. rapidus. Habitat stabilization is crucial for the recovery of this endangered species. However, in the past distributed sites, disturbances such as stream development and weir construction have altered streams physico-chemically and result in changes of M. rapidus. Therefore, a comprehensive plan that considers both stream connectivity and water quality is needed to manage and restore the habitat of M. rapidus.
Decabromodiphenyl ether (BDE209) is a persistent aromatic compound widely associated with environmental pollutants. Given its persistence and possible bioaccumulation, exploring a feasible technique to eradicate BDE209 efficiently is critical for today’s environmentally sustainable societies. Herein, an advanced nanocomposite is elaborately constructed, in which a large number of titanium dioxide ( TiO2) nanoparticles are anchored uniformly on two-dimensional graphene oxide (GO) nanosheets ( TiO2/GO) via a modified Hummer’s method and subsequent solvothermal treatment to achieve efficient photocatalytic degradation BDE209. The obtained TiO2/ GO photocatalyst has excellent photocatalytic due to the intense coupling between conductive GO nanosheets and TiO2 nanoparticles. Under the optimal photocatalytic degradation test conditions, the degradation efficiency of BDE209 is more than 90%. In addition, this study also provides an efficient route for designing highly active catalytic materials.