검색결과

검색조건
좁혀보기
검색필터
결과 내 재검색

간행물

    분야

      발행연도

      -

        검색결과 1,966

        202.
        2019.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        정삼투 공정에 유용한 유도용질로서 diethyl malonate를 사용한 citrate 계열의 유기 화합물을 합성하였다. 최종적으로 얻은 potassium pentane-1,3,3,5-tetracarboxylate는 1H-NMR과 13C-NMR을 통하여 확인하였다. 유도용질의 물성을 확인 하기 위해 삼투압, 용해도, 수투과도, 역염 투과도를 측정하였다. 합성한 유도용액을 사용하여 정삼투 공정을 진행한 결과, 동일한 citrate 계열인 trisodium citrate 및 tripotassium citrate보다 높은 수투과량을 나타내었으며 염의 역확산 정도는 NaCl에 비하여 매우 낮은 값을 나타내었다. 합성된 유도용질의 삼투압은 NaCl보다 약 25% 낮았으나 물에 대한 용해도는 NaCl의 8.8 배인 317 g/100 g water의 값을 나타내었다. 정삼투 종료 후 유도용질의 회수를 위해 상용화된 나노여과막을 사용하였고, 낮은 압력에서 효율적으로 회수가 가능하였다.
        4,200원
        205.
        2019.04 KCI 등재 구독 인증기관 무료, 개인회원 유료
        대장균 효소 β-gal를 이용하여 합성된 BzO-gal의 분자구조를 NMR (1H-와 13C-)과 고성능 mass spectrometry를 이용하여 분석하였다. BzO-gal은 1H NMR에서 14개의 proton으로부터 12개의 피크를 나타내었다. 방향족 고리에서 오는 5개의 proton 피크와 벤질기의 CH2에서 오는 2개의 proton 피크는 벤질알코올이 존재함을 나타낸다. 지방족 사슬 영역인 dH 4.32 ~ 3.46 ppm에서 나타나는 7개의 proton 피크로부터 단당류가 도입되었음을 확인할 수 있었다. 13C NMR 스팩트럼에서 나타난 11개의 carbon 피크도 또한 벤질알코올에 단당이 도입되었음을 나타낸다. BzO-gal의 분자량을 확인하기 위하여 mass spectrometry 로 분석한 결과 m/z가 293.0994인 BzO-gal의 sodium adduct ion ([M+Na]+)을 확인할 수 있었다. 이러한 결과를 바탕으로 세포독성이 감소된 첨가물 개발을 기대하고 있으며, 추가적인 후속연구를 진행할 예정이다.
        4,000원
        206.
        2019.03 KCI 등재 구독 인증기관 무료, 개인회원 유료
        In order to increase the seismic safety of nuclear power plant (NPP) structures, a technique to reduce the seismic load transmitted to the NPP structure by using a seismic isolation device such as a lead-rubber bearing has recently been actively researched. In seismic design of NPP structures, three directional (two horizontal and one vertical directions) artificial synthetic earthquakes (G0 group) corresponding to the standard design spectrum are generally used. In this study, seismic analysis was performed by using three directional artificial synthetic earthquakes (M0 group) corresponding to the maximum-minimum spectrum reflecting uncertainty of incident direction of earthquake load. The design basis earthquake (DBE) and the beyond design basis earthquakes (BDBEs are equal to 150%, 167%, and 200% DBE) of G0 and M0 earthquake groups were respectively generated for 30 sets and used for the seismic analysis. The purpose of this study is to compare seismic responses and seismic fragility curves of seismically isolated NPP structures subjected to DBE and BDBE. From the seismic fragility curves, the probability of failure of the seismic isolation system when the peak ground acceleration (PGA) is 0.5 g is about 5% for the M0 earthquake group and about 3% for the G0 earthquake group.
        4,200원
        207.
        2019.03 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The BX composite beam is designed to have the same cross-section regardless of the size of the momentum, which is a disadvantage of the existing steel structure. Combination of the H-beam end compressive material and the H-section steel tensile reinforcement according to the moment size in a single span, It is possible to say that it is an excellent synthesis which increases the performance. When underground and overhead structures are constructed, it is possible to reduce the bending, increase lateral stiffness, reduce construction cost, and simplify joints. The seamability of the joining part is a simple steel composite beam because of the decrease of the beam damping at the center of the beam and the use of the end plate of the new end compressing material. In the case of structures with long span structure and high load, it is advantageous to reduce the material cost by designing large steel which is high in price at less than medium steel.
        4,000원
        208.
        2019.03 KCI 등재 구독 인증기관 무료, 개인회원 유료
        This paper assesses the structural performance (force-slip response, slip modulus, and failure modes) of a CLT-concrete composite by conducting fifteen push-out test specimens. In addition, non-linear 3D finite element analysis was also developed to simulate the load-slip behavior of the CLT-concrete specimens under shear load. All 15 test specimens simulating the effect of concrete thickness, connection angle and penetration depth with four different shear connector types were built and tested to evaluate the flexural performance. Experimental results show that the maximum shear capacity for the composite action is obtained when the fixing angle is 90° and the penetration depth of 95mm for SC normal screw was used to achieve ductile failure compared to other shear connectors.
        4,000원
        209.
        2019.03 KCI 등재후보 구독 인증기관 무료, 개인회원 유료
        3-부티닐-p-톨루엔술포네이트를 이용한 2-에티닐피리딘의 무촉매중합을 통하여 이온성 전도성 고분자를 합성하였다. 합성 고분자의 분자구조는 IR, NMR, UV-visible 분광분석기로 확인하였다. 공액구조 주사슬 고분자의 특징적인 π → π* 전이에 기인하는 약하면서도 완만한 흡수 피크를 800 nm까지 보여 주었다. 합성한 고분자의 전기화학적 특성과 전기광학 특성을 측정하고 분석하였다. 이 고분자는 도핑과 탈도핑 사이에서 매우 안정한 비가역 전기화학적 거동을 보였다.
        4,000원
        210.
        2019.03 KCI 등재후보 구독 인증기관 무료, 개인회원 유료
        전이금속촉매를 사용한 4,4-비스[(트리플로로아세톡시)메틸]-1,6-헵타디인의 고리화중합을 통하여 고분자 반복단위 내에 고리구조를 갖는 공액구조 고분자인 폴리{4,4-비스[(트리플로로아세톡시)메틸]-1,6-헵타디인}(PBTFMH)을 합성하였다. 일반적으로 몰리브데늄 계 촉매를 사용한 경우의 중합수율이 텅스텐 계 촉매 를 사용한 경우의 그것보다는 높게 나타났다. 합성한 고분자는 중합과정중의 가교화반응으로 대부분 유기 용매에 용해하지 않았다. 고분자의 IR 스펙트럼에서는 단량체의 그것에서 나타났던 아세틸렌의 C≡C, 및 ≡C-H 신축진동띠를 보여주지 않았다. 이 고분자는 XRD 회절분석 결과 대부분 무정형상임이 밝혀졌다.
        4,000원
        211.
        2019.02 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        Transition metal oxide is widely used as a water electrolysis catalyst to substitute for a noble metal catalyst such as IrO2 and RuO2. In this study, the sol-gel method is used to synthesize the CuxCo3-xO4 catalyst for the oxygen evolution reaction (OER),. The CuxCo3-xO4 is synthesized at various calcination temperatures from 250 ℃ to 400 ℃ for 4 h. The CuxCo3- xO4 synthesized at 300 ℃ has a perfect spinel structure without residues of the precursor and secondary phases, such as CuO. The particle size of CuxCo3-xO4 increases with an increase in calcination temperature. Amongst all the samples studied, CuxCo3- xO4, which is synthesized at 300?, has the highest activity for the OER. Its onset potential for the OER is 370 mV and the overpotential at 10 mA/cm2 is 438 mV. The tafel slope of CuxCo3-xO4 synthesized at 300 ℃ has a low value of 58 mV/dec. These results are mainly explained by the increase in the available active surface area of the CuxCo3-xO4 catalyst.
        4,000원
        212.
        2019.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Current synthesis processes for titanium dioxide (TiO2) nanoparticles require expensive precursors or templates as well as complex steps and long reaction times. In addition, these processes produce highly agglomerated nanoparticles. In this study, we demonstrate a simple and continuous approach to synthesize TiO2 nanoparticles by a salt-assisted ultrasonic spray pyrolysis method. We also investigate the effect of salt content in a precursor solution on the morphology and size of synthesized products. The synthesized TiO2 nanoparticles are systematically characterized by X-ray diffraction, transmission electron micrograph, and UV-Vis spectroscopy. These nanoparticles appear to have a single anatase phase and a uniform particle-size distribution with an average particle size of approximately 10 nm. By extrapolating the plots of the transformed Kubelka-Munk function versus the absorbed light energy, we determine that the energy band gap of the synthesized TiO2 nanoparticles is 3.25 eV
        4,000원
        213.
        2019.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        합성보에 휨모멘트가 작용하면, 콘크리트 슬래브의 아랫면과 강재보의 윗면은 각각 인장력과 압축력에 의하여 팽창과 수축을 한다. 필연적으로 두 부재의 사이에서는 미끄러지려고 하는 수평전단력이 작용하게 되며, 이에 저항할 수 있는 전단 연결재의 역할이 매우 중요하다. 이 연구에서는 화약의 폭발력을 사용하여 강재보의 플랜지에 전단연결재를 고정하는 방법을 개발하였다. 개발 고정방법의 구조성능을 검증하기 위하여 보-기둥 접합부 실험과 유한요소해석을 수행하였다. 실험 및 해석결과를 기반으로 판단했을 때, 개발된 접합방식을 통하여 충분한 연성 및 강도를 확보할 수 있을 것으로 판단된다.
        4,000원
        214.
        2019.02 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The gas sensor is essential to monitoring dangerous gases in our environment. Metal oxide (MO) gas sensors are primarily utilized for flammable, toxic and organic gases and O3 because of their high sensitivity, high response and high stability. Tungsten oxides (WO3) have versatile applications, particularly for gas sensor applications because of the wide bandgap and stability of WO3. Nanosize WO3 are synthesized using the hydrothermal method. Asprepared WO3 nanopowders are in the form of nanorods and nanorulers. The crystal structure is hexagonal tungsten bronze (MxWO3, x =< 0.33), characterized as a tunnel structure that accommodates alkali ions and the phase stabilizer. A gas detection test reveals that WO3 can detect acetone, butanol, ethanol, and gasoline. This is the first study to report this capability of WO3.
        4,000원
        215.
        2019.01 KCI 등재 SCOPUS 구독 인증기관 무료, 개인회원 유료
        Three-dimensional(3D) printing is a process for producing complex-shaped 3D objects by repeatedly stacking thin layers according to digital information designed in 3D structures. 3D printing can be classified based on the method and material of additive manufacturing process. Among the various 3D printing methods, digital light processing is an additive manufacturing technique which can fabricate complex 3D structures with high accuracy. Recently, there have been many efforts to use ceramic material for an additive manufacturing process. Generally, ceramic material shows low processability due to its high hardness and strength. The introduction of additive manufacturing techniques into the fabrication of ceramics will improve the low processability and enable the fabrication of complex shapes and parts. In this study, we synthesize silica composite material that can be applied to digital light processing. The rheological and photopolymeric properties of the synthesized silica composite are investigated in detail. 3D objects are also successfully produced using the silica composite and digital light processing.
        4,000원
        216.
        2018.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        세리아 입자의 합성을 위하여 분무열분해 시 유기 첨가제인 EG(ethylene glycol)과 CA(citric acid)를 첨가하여 중공성 및 다공성을 갖는 CeO2 마이크로 크기의 입자를 제조하였으며 첨가량에 따른 특성을 비교하였다. 분무열분해과정, 후소성 및 볼밀링 과정을 적절히 조합하여 만든 6가지 경로에 의해 나노 크기의 세리아 입자를 합성하였다. 6가지 경로 중 EG 및 CA가 0.05M 첨가된 Ce(III)가 전구체 수용액을 이용하여 분무열분해→후소성→볼밀링→후소성의 경로에 의해 얻어진 CeO2 입자에 대해 TEM 분석으로 측정한 입자의 평균 크기 24 nm(편차=3.8 nm)는 Debye-Scherrer식에 의해 계산된 1차 입자의 크기(20 nm)와 가장 유사한 크기를 나타내었다. 제조된 나노입자분말의 형태적 및 구조적 특성을 알아보기 위하여 SEM(Scanning Electron Microscopy), XRD(X-Ray Diffractometer) 및 TEM(Transmission Electron Microscopy)을 통하여 특성을 분석하였다.
        4,900원
        217.
        2018.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        비식용 원료인 Palm Acid Oil, 동물성 폐유지 등은 상대적으로 자유 지방산 함량이 높기 때문에 일반적인 염기 촉매를 이용한 전이에스테르화 반응에 적합하지 않다. 효소 촉매를 이용하면 염기 촉매에서 해결할 수 없는 몇 가지 문제를 해결할 수 있으며, 에너지 소비가 작고, 바이오디젤 부산물인 글리세롤 회수가 쉬우며, 자유 지방산 함량이 높은 트리글리세라이드에 대한 전이에스테르화 반응이 가능하다. 본 연구에서는 고정화 효소 촉매를 이용하여 1 ton/day 용량의 반응기에서 비식용 폐유지를 바이오디젤로 합성하였으며, 반응 공정의 변수를 최적화하였다.
        4,000원
        218.
        2018.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        The impact of different mixing methods and sintering temperatures on the microstructure and piezoelectric properties of PZNN-PZT ceramics is investigated. To improve the sinterability and piezoelectric properties of these ceramics, the composition of 0.13Pb((Zn0.8Ni0.2)1/3Nb2/3)O3-0.87Pb(Zr0.5Ti0.5)O3 (PZNN-PZT) containing a Pb-based relaxor component is selected. Two methods are used to create the powder for the PZNN-PZT ceramics. The first involves blending all source powders at once, followed by calcination. The second involves the preferential creation of columbite as a precursor, by reacting NiO with Nb2O5 powder. Subsequently, PZNN-PZT powder can be prepared by mixing the columbite powder, PbO, and other components, followed by an additional calcination step. All the PZNNPZT powder samples in this study show a nearly-pure perovskite phase. High-density PZNN-PZT ceramics can be fabricated using powders prepared by a two-step calcination process, with the addition of 0.3 wt% MnO2 at even relatively low sintering temperatures from 800℃ to 1000℃. The grain size of the ceramics at sintering temperatures above 900℃ is increased to approximately 3 μm. The optimized PZNN-PZT piezoelectric ceramics show a piezoelectric constant (d33) of 360 pC/N, an electromechanical coupling factor (kp) of 0.61, and a quality factor (Qm) of 275.
        4,000원
        219.
        2018.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        Despite numerous advances in the preparation and use of GaN, and many leading-edge applications in lighting technologies, the preparation of high-quality GaN powder remains a challenge. Ammonolytic preparations of polycrystalline GaN have been studied using various precursors, but all were time-consuming and required high temperatures. In this study, an efficient and low-temperature method to synthesize high-purity hexagonal GaN powder is developed using sub-micron Ga2O3 powder as a starting material. The sub-micron Ga2O3 powder was prepared by an ultrasonic spray pyrolysis process. The GaN powder is synthesized from the sub-micron Ga2O3 powder through a nitridation treatment in an NH3 flow at 800℃. The characteristics of the synthesized powder are systematically examined by X-ray diffraction, scanning and transmission electron microscopy, and UV-vis spectrophotometer.
        4,000원
        220.
        2018.12 KCI 등재 구독 인증기관 무료, 개인회원 유료
        풀무치[Locusta migratoria (메뚜기목: 메뚜기과)]를 사육할 때 보조먹이로서 전지분유, 밀기울, 옥수수잎 가루, 설탕을 주성분으로 한 혼합 인공사료를 제조하였다. 갓부화 약충에 인공사료만을 제공하여 성충 사망 때까지 사육하였을 때, 다음 세대 집단을 얻지 못했다. 인공사료를 매일 제공하면서 옥수수 잎을 하루걸러 제공하였을 때도 다음 세대 개체를 얻지 못했다. 그러나 인공사료와 옥수수 잎을 하루걸러 번갈아 제공하였을 때는 이후 4세대까지 사육이 가능하였다. 성충의 생식력도 옥수수 잎과 인공사료를 매일 같이 제공한 경우보다, 두 먹이를 하루걸러 번갈아 제공 한 경우가 더 높았다. 이상의 결과로 본 연구에서 개발된 인공사료를 주먹이인 식물체의 보조먹이로 삼아 일정기간 풀무치 집단 유지에 이용할 수 있을 것으로 추정되었다.
        4,000원