The current disinfection method of vehicles being applied in South Korea has various shortcomings. So, the epidemic has generated continuously at livestock farms. It is very important to develop an effective disinfection system for reduction of the epidemic. And various basic data is required for this development. Therefore, this study was performed to identify the nozzle type and proper discharge pressure of sprayers. The experiment was conducted from January 10, 2012 until February 28, 2012. All the performance measurement experiments were repeated five times. The subjects of experiment were the A, B and C company’s products. The sprayed capacity, angle of spray and the covering area ratio were measured for each product. As a result, the sprayed capacity, angle of spray and the covering area ratio were increased as the discharge pressure of the sprayer was increased. In conclusion, the conical shaped of the nozzle is considered more appropriate than V-shaped, and the proper discharge pressure is expected to be at least 20kg/cm2.

목적 : 본 연구에서는 휠체어 사용 장애인을 위한 욕창예방방석 중재와 방석의 종류 및 효과 측정 방법에 대한 논문 고찰을 통해 임상현장에 적용할 수 있는 근거를 제시하고자 한다. 연구방법 : 전자 데이터베이스 RISS, KISS, Scopus, PubMed와 Google Scholar를 사용하여 2010년부터 2015 년까지의 논문을 검색하였다. 주요검색 용어로 “Pressure Ulcer AND Wheelchair AND Cushion”을 사용하 였다. 검색된 논문은 3차 분류를 거쳐 최종적으로 13개의 논문을 선정하였으며 이를 분석 고찰 하였다. 결과 : 연구 결과는 연구 참여자와 중재로 사용된 욕창예방방석의 종류, 중재가 적용된 환경 그리고 효과 검증을 위해 사용된 측정 방법을 기준으로 분석하고 정리하였다. 논문의 질적 수준은 단일 그룹 실험 논문이 8편으로 가장 많았고 연구 참여자는 비장애인 대상에서 척수손상장애인 대상으로 변화되어지는 양상을 보였다. 연구가 수행된 환경도 실험실 기반에서 지역사회를 기반으로 한 연구로 증가하는 양상을 보였다. 욕창예방방석의 종류는 공기방석에 대한 연구가 가장 많았으나 최근에는 맞춤형 방석의 연구가 활발하게 진행 중이었다. 욕창예 방방석의 효과에 대한 측정 방법은 좌면의 압력을 측정하는 방법이 전체적으로 가장 많았으나, 최근에는 방석 사용자의 사용성과 주관적 만족도를 측정하는 방법이 증가하고 있다. 결론 : 이번 연구를 통하여 욕창예방방석 중재와 방석의 종류 및 효과를 측정하는 방법에 대해 알 수 있었다. 이를 근거로 작업치료사의 욕창예방방석 서비스에 대한 임상적 근거를 제공하고 추후 연구에 대한 방향을 제시하고자 하였다. 추후에는 본 연구 결과를 바탕으로 욕창예방방석에 대한 개발과 연구 및 임상적 서비스 근거 마련에 대한 연구가 더욱 활발하게 이루어져야 할 것이다.

As CFRP with only a single material shows the various fracture properties, it has been applied to the many areas through the whole industry. The method bonding with adhesive has been recommended to apply the CFRP to structure. But it is inevitable that the mechanical joints with bolt, nut and rivet have been used sometimes. This study investigates the effect that these joints influence the CFRP panel through the analysis result. The analysis models as CFRP panels with the thickness of 5 mm have four kinds of layer angles which are 30°, 45°, 60° and 75°. The fracture property is examined when the pressure by the mechanical joint is applied to the upper panel. As the joint pressure is distributed most effectively in case of the layer angle of 60°, it is shown that this pressure becomes lower and the deformation of panel becomes lowest. On the basis of this study result, it is thought that the foundation data for the design of CFRP structure can be provided and contributed to the safety design of structure.

The measuring equipment capable of thermo measuring of wide range thermo range(0℃ ~ 160 0℃) will be developed in a high temperature and high pressure state. The developed technology is a combination of one measuring two different temperatures measured in the measuring to a high temperature as possible at a low temperature from thermocouple module(thermocouple) to develop an integrated measuring device capable of measuring the broadband. Also, to develop two or more guard module to ensure the water-tightness and durability of the device to develop in a vacuum or high pressure is applied to the one-piece measuring device.

Background: Lumbar stabilization (LS) improve the thickness of the quadratus lumborum (QL) muscle and muscle activity of the gluteus medius (GM) muscle during hip abduction in a side-lying position in patients with low back pain (LBP). Objects: The purpose of this study was to assess the effects of LS on muscle thickness of QL and muscle activity of GM during hip abduction in side-lying in patients with LBP. Methods: The study included 32 patients with LBP, who were randomly divided into the control group and experimental group, each with 16 patients. All subjects performed 35° preferred hip abduction (control group) and 35° hip abduction with LS (experimental group) during side-lying. An ultrasonography and a surface electromyography were used to measure the thickness of the QL muscle, and the muscle activities of the GM muscle respectively. Independent t-test was used to compare the muscle thickness of the QL and the muscle activity of the GM muscle, respectively. Results: Anterio-posterior diameter in the muscle thickness of QL muscle was decreased significantly in hip abduction with LS more than in preferred hip abduction (p<.001), but medio-lateral diameter in the muscle thickness of QL muscle was not significantly different between in preferred hip abduction and in hip abduction with LS (p=.06). The muscle activity of GM was increased significantly in hip abduction with LS more than in preferred hip abduction (p<.001). Conclusion: These findings suggest that hip abduction with LS could be recommended as a hip abduction for LS and a prevention unwanted compensatory pelvic lateral tilting movement.

재래식 해수담수화 수평적 압력용기 설계는 후단에 있는 역삼투막에는 농축수에 의해 수질악화 및 생산수저감 등이 동반된다. 이를 해결하기 위해 본 연구에서는 개념적인 중앙 주입식 압력용기가 생산수 단가에 미치는 영향과 역삼투 공정 설계 시 주요 인자들이 성능에 미치는 영향을 조사를 위해 상업화된 역삼 투 프로그램인 ROSA를 이용하여 분석하였다. 그 결과 중앙 주입식 압력용기를 이용할 경우 총괄적인 회수율과 SEC 측면에서 성능이 저하하지만, 막 모듈 당 생산되는 생산수량이 증가하는 것으로 나타났다. 또한 생산수의 수질개선은 2단 설계의 용량 감소로 인하여 건설비 저감으로 연계되는 것으로 조사되었다. 본 연구는 국토교통부 플랜트연구사업의 연구비지원(과제번호 16IFIP-B089908-03)에 의해 수행되었습니다.

정삼투막 성능 예측에는 Solution-diffusion model이 지배적으로 활용되어 왔으나, 기존 연구에서 수압과 삼투압이 동시에 작용하는 가압형 정삼투 공정에 대한 예측정확도가 감소하며, 이를 위해 수압이 투과성능에 미치는 영향을 convection과 diffusion을 동시에 고려해야한다는 연구결과가 보고되었다. 본 연구에서는 CTA-ES 및 PA-TFC 정삼투막을 이용하였으며, 활성층 측에는 NaCl 용액을, 지지층 측에는 증류수를 주입하고, 활성층 측에 삼투압과 동일한 수압을 가하여 농도변화에 따른 수투과도 및 염투과도의 변화양상을 평가하였다.

사이드 스트림 방식의 막 모듈을 대상으로 유입 유량을 수직으로 균등하게 분포시킬 수 있는 방안을 CFD로 설계한 결과, 내부 유입 수리구조에 유공 격벽 을 설치함으로써 모듈내로의 유입유량은 표준편차 기준으로 약 40% 정도 감소 됨을 확인하였다. 또한 CFD 결과를 검증하고 사이드 스트림 막 모듈의 편중된 오염의 원인을 조사하기 위해 수행된 입자영상유속 측정 결과로부터 유입구 반대편 유공에서 막 모듈 내부로 들어오는 수체의 유속이 상대적으로 커 수체의 모멘텀이 유입구 측벽에 강한 전단력을 발생하지만 유입구 반대 측벽에서는 사류가 형성됨을 확인하였다.

This study was conducted to determine the association between dietary calcium intake and biomarkers related to lipid and glucose metabolism and inflammation in Korean patients with type 2 diabetes. Seventy-five subjects (41 males, 34 females) were recruited from a group of patients who had visited the department of endocrine medicine. Data on anthropometric characteristics, clinical indices such as hemoglobin A1c and C-reactive protein (CRP), and dietary nutrient intakes were collected. Subjects were divided into three groups on the basis of their calcium intake [<EAR (below estimated average requirement), EAR-RNI (between EAR and recommended nutrient intake), >RNI (above RNI)]. Average calcium intake of <EAR, EAR-RNI, >RNI groups were 462.7±18.7, 649.7±12.8, and 895.7±21.7 mg, respectively. Energy intake was not different among groups but intakes of protein, total and saturated fatty acids were significantly higher in >RNI group than <EAR group. Analysis of covariance revealed that HDL cholesterol level was significantly higher in EAR-RNI group, as compared to <EAR group after adjustment with confounders such as age, sex, BMI and energy intake (p<0.05). Levels of CRP and homeostasis model assessment 2-insulin resistance (HOMA2-IR) were significantly lower in EAR-RNI group. Total cholesterol level was higher in EAR-RNI and >RNI groups, although within the normal range. Our results suggest that dietary calcium intake may influence the levels of HDL-cholesterol, CRP and HOMA2-IR and subsequently, help management/treatment of type 2 diabetes patients.

As CFRP with only a single material shows the various fracture properties, it has been applied to the many areas through the whole industry. The method bonding with adhesive has been recommended to apply the CFRP to structure. But it is inevitable that the mechanical joints with bolt, nut and rivet have been used sometimes. This study investigates the effect that these joints influence the CFRP panel through the analysis result. The analysis models as CFRP panels with the thickness of 5 mm have four kinds of layer angles which are 30°, 45°, 60° and 75°. The fracture property is examined when the pressure by the mechanical joint is applied to the upper panel. As the joint pressure is distributed most effectively in case of the layer angle of 60°, it is shown that this pressure becomes lower and the deformation of panel becomes lowest. On the basis of this study result, it is thought that the foundation data for the design of CFRP structure can be provided and contributed to the safety design of structure.

Ni and Ni-Cr reinforced Al alloy (AC8A) composites were fabricated by low pressure infiltration process. Porous Ni was applied as preform. Ni reinforced AC8A composites were fabricated under 0.3 MPa at 650, 700 and 750 degrees centigrade, respectively, while Ni-Cr reinforced AC8A composites were fabricated under low pressure limited to the maximum of 0.5 Mpa at 750, 800 and 850 degrees centigrade, respectively. Microstructure and phase composition of the composites were evaluated by optical microscope, X-Ray diffraction (XRD), electro-probe micro analyzer (EMPA). Intermetallic compounds Al3Ni and CrSi were observed in the composites. The results indicate that the grain size has been increasing with the increase of the infiltration temperatures. However, the wear resistance of Ni/AC8A and Ni-Cr AC8A peaked at 650 degree centigrade and 800 degrees centigrade, respectively. In addition, based on the wear characteristics and wear surfaces, Ni-Cr/AC8A composites have a better wear resistance than Ni/AC8A composites and AC8A.

In the water supply pipeline system polyethylene (PE), polyvinyl chloride (PVC), and ductile cast iron pipe are mostly used. However, they have some problems such as reduced durability due to material degradation, defects in connections, the pipelines breakage, and lack of continuous maintenance. Recently, research on durable and outstanding corrosion resistance glass fiber reinforced polymer plastic (GFRP) pipe is being actively conducted. GFRP is classified into the flexible pipe and when soil pressure and live load act on buried GFRP pipe, the load acting on the pipe is transferred to the surrounding soil. So, pipe will support the load with the surrounding soil. In this paper, to apply GFRP pipe for the water supply pipeline system, the structural reliability of GFRP water supply pipe buried underground should be investigated by examining the mechanical properties of GFRP pipe as well as the soundness of the pipe under buried state. The field test of buried pipe is conducted and the results are analyzed and discussed.

The purpose of this research was to investigate the effect of weighting agent (WA) and high pressure homogenization (HPH) on the stability of water-in-oil-in-water double emulsion (DE). To prepare oil phase (O), olive oil, glycerol ester of wood rosin (WA; variable 1), and polyglycerol polyricinoleate (lipophilic emulsifier), and for interior water phase (W1), deionized water, gelatin, sodium chloride, ascorbic acid, and green tea extract(core material) were mixed and heated. When temperature of O and W1 reached up to 60℃, W1 was dispersed into O dropwisely followed by magnetic stirring at 1500 rpm for 2 min (O:W1=3:1). By applying homogenization at 4000 rpm for 2 min followed by ultrasonication for 4 min, water-in-oil primary emulsion (PE) was produced. And resting PE at 4℃ for 30 min was followed. For exterior water phase (W2), deionized water, sodium chloride, ascorbic acid, and polysorbate 80 (hydrophilic emulsifier) were mixed. When temperature of PE reached at room temperature (24 ± 2℃), PE was dispersed into W2 dropwisely followed by magnetic stirring at 1500 rpm for 15 min (PE:W2=1:3). By applying ultrasonication for 2 min followed by HPH at 500 bar for 1 to 3 times (variable 2), DE was produced. When DE was freshly produced, phase separation occurred at different period of time depending on whether variable 1 and 2 were applied or not (from 5 min to more than a day). The structure of DE was observed through optical and transmission electron microscopy. And relationship between the mean size of oil droplets and the occurring time of phase separation was studied. DE can be used as an appropriate delivery system for co-loading both hydrophilic and lipophilic bioactive compounds simultaneously, and promoting industrialization as well by applying it to food products, for example, beverage.

The purpose of this study was to identify the effects of continuous muscle strengthening applied to the antagonist of the sternocleidomatoid, upper trapezius, and pectoralis major, which are the shortened muscles of forward head posture(FHP) subjects, and Evjenth-Hamberg stretching(EHS) applied to the shortened muscles on changes in pressure pain threshold(PPT). Twenty subjects were divided into the continuous antagonist strengthening( CAS) group(n=10) and the EHS group(n=10), and each group performed its respective exercise three times a week for a six week period. The results were as follows: The comparison of changes in PPT within each group before and after the treatment showed a statistically significant difference( p<.05) according to the treatment period and a statistically significant difference according to the treatment period and method(p<.05). While the comparison of the tests of between subjects effects between the groups did not show a statistically significant difference, the CAS group exhibited better effects. The above results suggest that the combined application of CAS and EHS generates better effects on changes in PPT than the single application of EHS. Given that stretching and muscle strengthening exercises even for the short research period of six weeks could change the PPT, continuous exercises and a correct postural habit for a longer period of time are likely to help prevent chronic pain and correct FHP

본 연구는 여름철 참외 시설재배시 저압포그 처리에 의한 온도하강 및 과실 품질 향상 효과를 구명하기 위하여 수행하였다. 2015년 7월 26일 10시부터 18시까지 의 하우스 내부의 평균 온도는 무처리구 43.0oC에 비해 저압포그 처리구에서 35.4oC로 무처리구에 비해 7.6oC 정도 낮았다. 8월 13일 과실의 특성을 조사한 결과, 과중은 무처리구의 432g에 비해 96g 더 가볍고. 과육부 당도 11.0oBrix에 비해 1.3oBrix 더 높았으며 색도(a값)도 5.1에 비해 1.5 더 높아 우수하였다. 6월 23일부터 50일간 참외의 품질을 조사한 결과, 기형과율은 무처리구의 42.6%에 비하여 저압포그 처리구에서는 27.3%로 15.3%p 감소하였고, 상품과율은 무처리구의 57.4%에 비하여 저압포그 처리구에서 72.7%로 15.3%p 증가하였다. 10a당 수량은 무처리구의 2,234kg에 비하여 저압포그 처리구에서 26% 증 가하였다. 이상의 결과를 보아, 여름철 고온기 참외 시설 재배시 저압포그 처리로 온도하강 효과가 우수하여 품질이 향상되고 수량이 증가한 것으로 판단되었다.

Injection rate, injection quantity and injection timing of fuel are controlled precisely by electric control in CRDI system.Particularly, injection rate being influenced with injection pressure affects to spray characteristics and fuel-air ratio, so it is a very important factor in diesel combustion. In this study, injection rates in accordance with injection pressure at a constant ambient pressure were measured with Zeuch's method. Under the same condition, non-evaporating spray images were taken with a high speed camera and analyzed carefully with Adobe Photoshop CS3. Macroscopic spray characteristics and breakup processes in the spray could be found from the examined and analyzed data. Injection start time and injection period were practically affected with injection pressure. Also, initial injection rate, spray penetration, spray angle and breakup of high density droplets region in the spray were affected with injection pressure. The results and techniques of spray visualization and injection rate measurement in this study would be practically effective to study a high pressure diesel spray for common rail direct injection system.