The design of non-precious electrocatalysts with low-cost, good stability, and an improved oxygen reduction reaction(ORR) to replace the platinium-based electrocatalyst is significant for application of fuel cells and metal-air batteries with high energy density. In this study, we synthesize iron-carbide(Fe3C) embedded nitrogen(N) doped carbon nanofiber(CNF) as electrocatalysts for ORRs using electrospinning, precursor deposition, and carbonization. To optimize electrochemical performance, we study the three stages according to different amounts of iron precursor. Among them, Fe3C-embedded N doped CNF-1 exhibits the most improved electrochemical performance with a high onset potential of −0.18 V, a high E1/2 of −0.29 V, and a nearly four-electron pathway (n = 3.77). In addition, Fe3C-embedded N doped CNF-1 displays exellent long-term stabillity with the lowest ΔE1/2= 8 mV compared to the other electrocatalysts. The improved electrochemical properties are attributed to synergestic effect of N-doping and well-dispersed iron carbide embedded in CNF. Consequently, Fe3C-embedded N doped CNF is a promising candidate for non-precious electrocatalysts for high-performance ORRs.

Cu2ZnSn(S,Se)4 (CZTSSe) films were prepared on Mo coated soda lime glass substrates by sulfo-selenization of sputtered stacked Zn-Sn-Cu(CZT) precursor films. The precursor was dried in a capped state with aqueous NaOH solution. The CZT precursor films were sulfo-selenized in the S + Se vapor atmosphere. Sodium was doped during the sulfo-selenization treatment. The effect of sodium doping on the structural and electrical properties of the CZTSSe thin films were studied using FE-SEM(field-emission scanning electron microscopy), XRD(X-ray diffraction), XRF(X-ray fluorescence spectroscopy), dark current, SIMS(secondary ion mass spectrometry), conversion efficiency. The XRD, XRF, FE-SEM, Dark current, SIMS and cell efficiency results indicated that the properties of sulfo-selenized CZTSSe thin films were strongly related to the sodium doping. Further detailed analysis and discussion for effect of sodium doping on the properties CZTSSe thin films will be discussed.

A boron-doped diamond(BDD) electrode is attractive for many electrochemical applications due to its distinctive properties: an extremely wide potential window in aqueous and non-aqueous electrolytes, a very low and stable background current and a high resistance to surface fouling. An Ar gas mixture of H2, CH4 and trimethylboron (TMB, 0.1 % C3H9B in H2) is used in a hot filament chemical vapor deposition(HFCVD) reactor. The effect of argon addition on quality, structure and electrochemical property is investigated by scanning electron microscope(SEM), X-ray diffraction(XRD) and cyclic voltammetry(CV). In this study, BDD electrodes are manufactured using different Ar/CH4 ratios (Ar/CH4 = 0, 1, 2 and 4). The results of this study show that the diamond grain size decreases with increasing Ar/CH4 ratios. On the other hand, the samples with an Ar/CH4 ratio above 5 fail to produce a BDD electrode. In addition, the BDD electrodes manufactured by introducing different Ar/CH4 ratios result in the most inclined to (111) preferential growth when the Ar/CH4 ratio is 2. It is also noted that the electrochemical properties of the BDD electrode improve with the process of adding argon.

Lithium-ion batteries have been considered the most important devices to power mobile or small-sized devices due to their high energy density. LixCoO2 has been studied as a cathode material for the Li-ion battery. However, the limitation of its capacity impedes the development of high capacity cathode materials with Ni, Mn, etc. in them. The substitution of Mn and Ni for Co leads to the formation of solid solution phase LiNixMnyCo1-x-yO2 (NMC, both x and y < 1), which shows better battery performance than unsubstituted LiCoO2. However, despite a high discharge capacity in the Ni-rich compound (Ni > 0.8 in the metal site), poor cycle retention capability still remains to be overcome. In this study, aiming to improve the stability of the physical and chemical bonding, we investigate the stabilization effect of Ca in the Ni-rich layered compound Li(Ni0.83Co0.12Mn0.05)O2, and then Ca is added to the modified secondary particles to lower the degree of cationic mixing of the final particles. For the optimization of the final grains added with Ca, the Ca content (x = 0, 2.5, 5.0, 10.0 at.%) versus Li is analyzed.

연료 전지 구동 시 전기화학적 활성은 촉매와 연료, 전해질이 만나는 삼상계면에서 일어나며 연료전지의 성능은 이 삼상계면의 수에 영향을 받는다. 인산이 도핑된 Polybenzimidazole (PA-doped PBI)을 기반으로 한 고온 고분자 전해질막 연료전지 (HT-PEMFC)의 경우 막 내의 인산이 전해질의 역할을 하며 삼상계면 및 연료전지의 성능에 영향을 끼친다. PBI 막 내의 인산은 고분자 합성 용매인 폴리인산의 가수분해에 의해 생성된다. 본 연구에서는 Sol-Gel 법(Direct casting 법)으로 제조된 PA-doped PBI 막의 가수분해 조건을 달리하여 이에 따른 연료전지의 성능을 비교하여 보았다.

Nitrogen (N)-doped protein-based carbon as platinum (Pt) catalyst supports from tofu for oxygen reduction reactions are synthesized using a carbonization and reduction method. We successfully prepare 5 wt% Pt@N-doped protein-based carbon, 10 wt% Pt@N-doped protein-based carbon, and 20 wt% Pt@N-doped protein-based carbon. The morphology and structure of the samples are characterized by field emission scanning electron microscopy and transmission electron micro scopy, and crystllinities and chemical bonding are identified using X-ray diffraction and X-ray photoelectron spectroscopy. The oxygen reduction reaction are measured using a linear sweep voltammogram and cyclic voltammetry. Among the samples, 10 wt% Pt@N-doped protein-based carbon exhibits exellent electrochemical performance with a high onset potential of 0.62 V, a high E1/2 of 0.55 V, and a low ΔE1/2= 0.32 mV. Specifically, as compared to the commercial Pt/C, the 10 wt% Pt@N-doped proteinbased carbon had a similar oxygen reduction reaction perfomance and improved electrochemical stability.

Sb-doped SnO2 (ATO) transparent conducting films are fabricated using horizontal ultrasonic spray pyrolysis deposition (HUSPD) to form uniform and compact film structures with homogeneously supplied precursor solution. To optimize the molar concentration and transparent conducting performance of the ATO films using HUSPD, we use precursor solutions of 0.15, 0.20, 0.25, and 0.30 M. As the molar concentration increases, the resultant ATO films exhibit more compact surface structures because of the larger crystallite sizes and higher ATO crystallinity because of the greater thickness from the accelerated growth of ATO. Thus, the ATO films prepared at 0.25 M have the best transparent conducting performance (12.60±0.21 Ω/□ sheet resistance and 80.83% optical transmittance) and the highest figure-of-merit value (9.44±0.17 × 10-3 Ω-1). The improvement in transparent conducting performance is attributed to the enhanced carrier concentration by the improved ATO crystallinity and Hall mobility with the compact surface structure and preferred (211) orientation, ascribed to the accelerated growth of ATO at the optimized molar concentration. Therefore, ATO films fabricated using HUSPD are transparent conducting film candidates for optoelectronic devices.

Fluorine-doped tin oxide (FTO) coated NiCrAl alloy foam is fabricated using ultrasonic spray pyrolysis deposition (USPD). To confirm the influence of the FTO layer on the NiCrAl alloy foam, we investigated the structural, chemical, and morphological properties and chemical resistance by using USPD to adjust the FTO coating time (12, 18, and 24 min). As a result, when an FTO layer was coated for 24 min on NiCrAl alloy foam, it was found to have an enhanced chemical resistance compared to those of the other samples. This improvement in the chemical resistance of using USPD NiAlCr alloy foam can be the result of the existence of an FTO layer, which can act as a protection layer between the NiAlCr alloy foam and the electrolyte and also the result of the increased thickness of the FTO layer, which enhances the diffusion length of the metal ion.

Boron-doped diamond (BDD) electrode has an extremely wide potential window in aqueous and non-aqueous electrolytes, very low and stable background current and high resistance to surface fouling due to weak adsorption. These features endow the BDD electrode with potentially wide electrochemical applications, in such areas as wastewater treatment, electrosynthesis and electrochemical sensors. In this study, the characteristics of the BDD electrode were examined by scanning electron microscopy (SEM) and evaluated by accelerated life test. The effects of manufacturing conditions on the BDD electrode were determined and remedies for negative effects were noted in order to improve the electrode lifetime in wastewater treatment. The lifetime of the BDD electrode was influenced by manufacturing conditions, such as surface roughness, seeding method and rate of introduction of gases into the reaction chamber. The results of this study showed that BDD electrodes manufactured using sanding media of different sizes resulted in the most effective electrode lifetime when the particle size of alumina used was from 75~106 μm (#150). Ultrasonic treatment was found to be more effective than polishing treatment in the test of seeding processes. In addition to this, BDD electrodes manufactured by introducing gases at different rates resulted in the most effective electrode lifetime when the introduced gas had a composition of hydrogen gas 94.5 vol.% carbon source gas 1.6 vol.% and boron source gas 3.9 vol.%.

N-doped carbon nanofibers as catalysts for oxygen-reduction reactions are synthesized using electrospinning and carbonization. Their morphologies, structures, chemical bonding states, and electrochemical performance are characterized. The optimized N-doped carbon nanofibers exhibit graphitization of carbon nanofibers and an increased nitrogen doping as well as a uniform network structure. In particular, the optimized N-doped carbon nanofibers show outstanding catalytic activity for oxygen-reduction reactions, such as a half-wave potential (E1/2) of 0.43 V, kinetic limiting current density of 6.2 mA cm-2, electron reduction pathways (n = 3.1), and excellent long-term stability after 2000 cycles, resulting in a lower E1/2 potential degradation of 13 mV. The improvement in the electrochemical performance results from the synergistic effect of the graphitization of carbon nanofibers and the increased amount of nitrogen doping.

ZnO with wurtzite structure has a wide band gap of 3.37 eV. Because ZnO has a direct band gap and a large exciton binding energy, it has higher optical efficiency and thermal stability than the GaN material of blue light emitting devices. To fabricate ZnO devices with optical and thermal advantages, n-type and p-type doping are needed. Many research groups have devoted themselves to fabricating stable p-type ZnO. In this study, As+ ion was implanted using an ion implanter to fabricate p-type ZnO. After the ion implant, rapid thermal annealing (RTA) was conducted to activate the arsenic dopants. First, the structural and optical properties of the ZnO thin films were investigated for as-grown, as-implanted, and annealed ZnO using FE-SEM, XRD, and PL, respectively. Then, the structural, optical, and electrical properties of the ZnO thin films, depending on the As ion dose variation and the RTA temperatures, were analyzed using the same methods. In our experiment, p-type ZnO thin films with a hole concentration of 1.263 × 1018 cm−3 were obtained when the dose of 5 × 1014 As ions/cm2 was implanted and the RTA was conducted at 850 oC for 1 min.

Fluorine-doped tin oxide (FTO) nanoparticles have been successfully synthesized using ultrasonic spray pyrolysis. The morphologies, crystal structures, chemical bonding states, and electrochemical properties of the nanoparticles are investigated. The FTO nanoparticles show uniform morphology and size distribution in the range of 6-10 nm. The FTO nanoparticles exhibit excellent electrochemical performance with high discharge specific capacity and good cycling stability (620mA h g−1 capacity retention up to 50 cycles), as well as excellent high-rate performance (250 mA h g−1 at 700mAg−1) compared to that of commercial SnO2. The improved electrochemical performance can be explained by two main effects. First, the excellent cycling stability with high discharge capacity is attributed to the nano-sized FTO particles, which are related to the increased electrochemical active area between the electrode and electrolyte. Second, the superb high-rate performance and the excellent cycling stability are ascribed to the increased electrical conductivity, which results from the introduction of fluorine doping in SnO2. This noble electrode structure can provide powerful potential anode materials for high-performance lithiumion batteries.

The PBI membrane doped with phosphoric acid (PA) is one of the promising candidates for HT-PEMFC. The proton conductivity of PA doped PBI depends on the acid doping level (ADL). The method to fabricate porous PBI membrane using porogen were reported to increase the ADL. However, high ADL cause complete loss of the mechanical strength of the membranes. In this research, the dead-end porous PBI membranes were prepared using progen to increase the mechanical strength than porous PBI membrane and proton conductivity. The dead-end porous PBI membranes were investigated in terms of ionic conductivity, ADL, SEM and mechanical strength.

Bi2Te3 related compounds show the best thermoelectric properties at room temperature. However, n-type Bi2Te2.7Se0.3 showed no improvement on ZT values. To improve the thermolectric propterties of n-type Bi2Te2.7Se0.3, this research has Cu-doped n-type powder. This study focused on effects of Cu-doping method on the thermoelectric properties of n-type materials, and evaluated the comparison between the Cu chemical and mechanical doping. The synthesized powder was manufactured by the spark plasma sintering(SPS). The thermoelectric properties of the sintered body were evaluated by measuring their Seebeck coefficient, electrical resistivity, thermal conductivity, and hall coefficient. An introduction of a small amount of Cu reduced the thermal conductivity and improved the electrical properties with Seebeck coefficient. The authors provided the optimal concentration of Cu0.1Bi1.99Se0.3Te2.7. A figure of merit (ZT) value of 1.22 was obtained for Cu0.1Bi1.9Se0.3Te2.7 at 373K by Cu chemical doping, which was obviously higher than those of Cu0.1Bi1.9Se0.3Te2.7 at 373K by Cu mechanical doping (ZT=0.56) and Cu-free Bi2Se0.3Te2.7 (ZT=0.51).

본 연구에서는 발광층의 전자와 정공의 재결합 영역을 확인하고, 단계적 도핑구조를 이용하여 여기자들의 효율적인 분배를 통해 roll-off 효율을 감소시켜서 녹색 인광 유기발광다이오드의 수명 증가 를 나타냈다. 발광층 내 호스트는 양극성의 4,4,N,N'-dicarbazolebiphenyl (CBP)를 사용하여 전하의 이 동을 원활하게 하였다. 발광층을 네 구역으로 분할하여 각각 소자를 제작하였고, 네 구역의 도판트 농도 에 따라 발광효율과 수명 향상을 보였다. 이로써 발광층 내의 단계적 도핑구조를 이용하여 캐리어와 여 기자들이 원활하게 분배된 것을 확인하였다. 기준소자 대비 발광층의 도판트 농도를 5, 7, 11, 9% 순서 로 단계적 도핑구조를 적용한 device C의 수명이 약 73.70% 증가하였고, 휘도 효율은 51.10 cd/A와 외 부 양자 효율은 14.88%의 성능을 보였다.

Eu2+/Dy3+-doped Sr2MgSi2O7 powders were synthesized using a solid-state reaction method with flux (NH4Cl). Thebroad photoluminescence (PL) excitation spectra of Sr2MgSi2O7:Eu2+ were assigned to the 4f7-4f65d transition of the Eu2+ ions,showing strong intensities in the range of 375 to 425nm. A single emission band was observed at 470nm, which was the resultof two overlapping subbands at 468 and 507nm owing to Eu(I) and Eu(II) sites. The strongest emission intensity ofSr2MgSi2O7:Eu2+ was obtained at the Eu concentration of 3mol%. This concentration quenching mechanism was attributableto dipole-dipole interaction. The Ba2+ substitution for Sr2+ caused a blue-shift of the emission band; this behavior was discussedby considering the differences in ionic size and covalence between Ba2+ and Sr2+. The effects of the Eu/Dy ratios on thephosphorescence of Sr2MgSi2O7:Eu2+/Dy3+ were investigated by measuring the decay time; the longest afterglow was obtainedfor 0.01Eu2+/0.03Dy3+.

투명 전도성 산화물로서 알루미늄과 붕소가 함께 도핑된 아연산화물(AZOB)이 900℃에서 분무 열분해법에 의해 제조되었다. 얻어진 마이크론 크기의 AZOB 분말은 알루미늄, 붕소 및 아연의 수용액으로부터 얻어진다. 분무 열분해로 얻어진 마이크론 크기의 AZOB 분말은 700℃에서 두 시간동안의 후 소성 과정과 24 시간 동안의 볼 밀링을 통해 나노 크기의 AZOB으로 변환된다. AZOB을 구성하는 일차 입자의 크기를 Debye-Scherrer 식에 의해 계산하였고 압축된 AZOB 펠렛의 표면 저항을 측정하였다.

마이크론 크기를 가지는 ITO(indium tin oxide) 입자들은 인듐과 틴의 수용성 전구체들과 유기 첨가제를 분무 열분해하여 얻었다. 유기 첨가제로서는 에틸렌글리콜과 시트르산을 이용하였다. 분무 열분해 시 에틸렌글리콜과 시트르산과 같은 유기첨가제를 첨가하지 않고 얻어진 ITO 입자들은 구형이며 속이 꽉찬 형태를 가지는데 비해 유기 첨가제를 첨가하여 분무 열분해를 하면 얻어지는 ITO 입자들은 유기 첨가제의 양이 증가 할수록 껍질이 얇고 다공성이 증대된 중공 입자가 얻어진다. 유기첨가제를 첨가하지 않고 분무 열분해를 통해 얻어지는 마이크론 크기를 가지는 ITO는 700℃에서 두 시간 동안의 후소성과 24 시간동안의 습식 볼밀링에 의해 나노 크기의 ITO로 전환되지 않으나, 유기첨가제를 첨가하고 분무 열분해를 통해 얻어지는 마이크론 크기를 가지는 ITO는 700℃에서 두 시간 동안의 후소성과 24 시간 동안의 습식 볼밀링에 의해 나노 크기의 ITO로 쉽게 전환되었다. 응집된 나노 크기의 ITO의 일차 입자의 크기를 Debye-Scherrer 식에 의해 계산하였고 ITO 입자를 압축하여 만든 펠렛의 표면저항을 측정하였다.

유기태양전지의 투명전극으로서 기존의 값비싸고 깨지기 쉬운 Indium Tin Oxide (ITO) 전극을 대체하고자, 전도성 고분자인 poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS)를 적용하였다. 솔벤트의 도핑 농도에 따른 PEDOT:PSS 박막의 전기 전도도와 표면 거칠기의 특성 변화를 관찰하고, 그 결과가 PEDOT:PSS를 투명전극으로 사용한 유기태양전지의 특성에 미치는 영향을 연구하였다. PEDOT:PSS의 솔벤트 농도가 증가함에 따라, 박막의 표면 거칠기가 증가하고, 이는 유기태양전지의 단락전류의 변화를 야기했다. 또한, 소자의 홀 이동층이 얇아짐에 따라 광활성층의 단파장영역의 광흡수가 증가하는 것을 관찰할 수 있었다.

The existing metal getters are invariably covered with thin oxide layers in air and the native oxide layer must be dissolved into the getter materials for activation. However, high temperature is needed for the activation, which leads to unavoidable deleterious effects on the devices. Therefore, to improve the device efficiency and gas-adsorption properties of the device, it is essential to synthesize the getter with a method that does not require a thermal activation temperature. In this study, getter material was synthesized using palladium oxide (PdOx) which can adsorb H2 gas. To enhance the efficiency of the hydrogen and moisture absorption, a porous layer with a large specific area was fabricated by an etching process and used as supporting substrates. It was confirmed that the moisture-absorption performance of the SiO2/Si was characterized by water vapor volume with relative humidity. The gas-adsorption properties occurred in the absence of the activation process.