In this study, factors analysis is performed for reducing friction in elevation motion of a large television stand over 50-inch. The first is a pipe type cross-section control for accurate position control of the piston rod. Here it was compared with the pipe type and labyrinth type orifice cross-section. The second study is for specification decision and volume compensation experiment as an apparatus for compensating of the volume of the cylinder is compressed as the volume of piston rod. Consequently, in the orifice cross section study between pipe type and labyrinth type through CAE and experimental consideration, cross section of labyrinth type orifice is preferred for reducing of friction. The result of total consideration in stability problem and performance of volume compensation for specification decision and volume compensation experiment is determined the final speculation of hollow rod φ8×φ4 and riveting system.

In this study, factors analysis is performed for reducing friction in elevation motion of a large television stand over 50-inch. The first is a pipe type cross-section control for accurate position control of the piston rod. Here, it was compared with the pipe type and labyrinth type orifice cross-section. The second study attempted to reduce the frictional force the gas seal lip technology. As the result of the first study, in the orifice cross section study between pipe type and labyrinth type through CAE and experimental consideration, cross section of labyrinth type orifice is preferred for reducing of friction. As the result of the second study, in the gas seal lip technology, the outer-inner diameter of φ20×φ8 in the test result of hollow rod is revealed more proper if the weight of 50 inch television assumed as 30kgf.

충돌형태의 하중을 가지는 토석류는 큰 에너지를 가지는 하중이 충격을 통해 짧은 시간에 갑작스럽게 작용하여 구조물이 쉽게 파괴에 이르게 한다. 완충형 토석류 방호시설은 유연적 구조를 사용하여 구조물 이 충돌하는 토석류에 보다 긴 시간에 걸쳐 저항하도록 함으로써 저항성능을 높이는 형태의 구조물을 말 한다. 이러한 완충형 토석류 방호시설은 크게 내력을 지지하는 부분과 유연성을 담당하는 부분으로 나누 어지며, 압축스프링을 이용한 완충형 토석류 방호시설은 내력을 지지하는 부분을 두께가 두꺼운 와이어로 프로 구성하고 유연성을 담당하는 부분은 와이어로프에 압축스프링을 사용하여 유연성을 크게 증가시킨 새로운 형태의 방호시설을 말한다. 최근 집중호우와 국지성 폭우 등으로 인해 토석류 발생 빈도가 증가하고 있다. 이에 대한 방지책으로 많은 종류의 방호시설물들이 개발되고 설치되고 있으나 아직까지 이러한 산사태 방호시설물들에 대한 명 확한 설계방법이 제시되어있지 않다. 그 이유는 토석류의 토사유출량이나 운동에너지를 명확하게 정의하 는 것은 복잡한 과정을 거쳐야 하며, 어렵게 이를 정의하였다 하더라도 구조물 설계에 어떻게 적용시키는 가에 대한 방법적 문제가 존재하기 때문이다. 본 연구에서는 토석류의 토사유출량 산정을 프로그램화하여 단순화 시켰으며, 산정된 토사유출량을 사 용하여 개발된 압축스프링을 이용한 완충형 토석류 방호시설의 단면 형상과 단면 크기 설정 방법을 제시 한다. 먼저, 토석류의 토사유출량 산정을 프로그램화하기 위해 많이 사용되는 토사유출량 산정방법인 RUSLE방법을 사용하였다. 이를 프로그램화하기 위해 개념도를 파악하였으며 Excel의 script언어인 VBA 를 사용하여 구현하였다. 또한, 토석류가 발생하는 산악지형의 계곡형상은 단면형상이 주로 사다리꼴 형 태를 가지게 된다. 단면이 삼각형이나 사다리꼴 형태인 일반적인 토석류 방호시설의 저항단면크기는 시설 물의 높이를 결정하는 것이 핵심이다. 기존의 방법은 구조물의 높이를 산정하기 위해 평균폭을 가정하여 사용하였으나 이는 정확한 방법이 될 수 없다. 따라서 본 연구에서는 측정 가능한 하단의 폭과 앞서 산정 된 토석류의 양을 기반으로 정확한 구조물의 높이를 산정하는 방법을 제안하였다.

The polyurethane spring, which provides the restoring force for a sliding bridge bearing, governs the overall behavior of the bearing. An analytical model, therefore, which reflects actual geometrical shape and can be utilized easily in engineering practice, is needed to be developed. In this paper, a simplified model for analyzing the polyurethane spring utilized in the sliding bridge bearing is presented. The model is developed for a cylindrical tube based on Gent’s model, and can be utilized for various height-diameter ratios. The accuracy of the proposed model are compared to existing models via experimental data as well as numerical analysis results. The comparison result shows that the proposed model can be used in estimating mechanical behavior of the cylindrical tube shaped polyurethane spring.

Axial force of the bolt is very important for structural stability. To obtain stability of the structure, axial force of the bolt should satisfy the specification and be maintained over the time. Hence, It is important to the axial force of the bolt is measured and it manages. However, measuring of the axial force using sensors is very expensive. Torque method using frequently in the field is difficult to confirm accurately by the torque coefficient change. In this study, measuring of axial force using elastic force of the spring washer was studied. First, the relational formula is drawn about the pressure in which the spring washer model changes to the annular of the plane state. According to the axial force of the bolt, the necessity height of the spring washer is presented and the finite-element analysis model is recommended. The analysis model research, generally, the axial force of high strength bolt is confirmed. It expands to confirmation of the large caliber bolt.

The most time consuming operation during the tryout of new parts is the compensation of geometric deviations induced by springback. The variation of springback due to the noise factors such as material properties and forming conditions increase the difficulties of the compensation operation. If the forming process includes a drawing operation followed by a restriking operation, a robust design for springback compensation is needed for both operations. In this study, a new 2-stage procedure for robust springback compensation using Taguchi's orthogonal array experiments combined with the Pick-the-Winner rule and the design space reduction method is proposed. The effectiveness of the proposed method is shown with an example of the sidewall curl springback compensation in U-channel forming.

This study was conducted to analyze fishing capacity and bycatch by mesh size and entrance size of spring net pot conductedby water tank and field experiment. The water tank experiments were conducted by using traps with mesh size of 22 mm and entrance size of 120 mm and 140 mm, respectively in the water tank of NIFS. The field experiment was conducted using 5 kinds of spring net pot with mesh sizes of 20 mm, 22 mm, 35 mm and entrance size of 120 mm, 130 mm, 140 mm, 360 mm by coastal trap fishery vessel operating around the area of Geoje island. In the result of water tank experiments, the catch of conger eel was 1.5 times higher when using trap with entrance size of 140 mm than that of 120 mm. In the field experiment, when using same mesh size, the larger the entrance size, the higher amount of conger eel catch, bycatch and number of bycatch species. When using the same entrance size, the larger the mesh size, the lower amount of conger eel catch and number of bycatch species, whereas the amount of bycatch showed increasing trend.

It analyzes the new structure and mechanism of organ type accel pedal to have a double curve to obtain a low effort force has been devised an electronic accel pedal consisting of two springs. To confirm the characteristics of effort force on variation of spring constants for two springs, dynamic analyzes were performed by using the ADAMS software program. According to the result of the simulation analysis, new mechanism of organ type accel pedal has an inflection point of the curve of pedal effort force on variation of spring constants, k, in various range of pedal angle.

ㅊBy controlling the piston speed of the gas spring applying to the digital television stand application of the gas spring, a user can operate the elevation when the gas spring is working under long stroke(200～300 mm, the TV elevation displacement). According to stroke, by some devices with the problem rising from between the difference of external forces, the emotional quality in television elevational function is realized. The piston speed control technique is investigated to perform this experiment piston flow analysis and flow rate control for precise tubular cross section and propose a piston structure for elevation action. This study is for the development of the gas spring of the large size television stand with 50 inch over. In the gas spring development of elevation working, a device to compensate for the volume of the cylinder is generated as much the volume of the piston rod. As this study result, at the development of working gas spring, the hollow shaft is more favorable than the solid one in the apparatus to compensate for the cylinder volume generated.

Reinforced concrete shear walls are effective for resisting lateral loads imposed by wind or earthquakes. Observed damages of the shear wall in recent earthquakes in Chile(2010) and New Zealand(2011) exceeded expectations. Various analytical models have been proposed in order to incorporate such response features in predicting the inelastic response of RC shear walls. However, the model has not been implemented into widely available computer programs, and has not been sufficiently calibrated with and validated against extensive experimental data at both local and global response levels. In this study, reinforced concrete shear walls were modeled with fiber slices, where cross section and reinforcement details of shear walls can be arranged freely. Nonlinear analysis was performed by adding nonlinear shear spring elements that can represent shear deformation. This analysis result will be compared with the existing experiment results. To investigate the nonlinear behavior of reinforced concrete shear walls, reinforced concrete single shear walls with rectangular wall cross section were selected. The analysis results showed that the yield strength of the shear wall was approximately the same value as the experimental results. However, the yielding displacement of the shear wall was still higher in the experiment than the analysis. The analytical model used in this study is available for the analysis of shear wall subjected to high axial forces.

By controlling the piston speed of the gas spring applying to the digital television stand application of the gas spring, a user can operate the elevation when the gas spring is working under long stroke(200～300 mm, the TV elevation displacement). According to stroke, by some devices with the problem rising from between the difference of external forces, the emotional quality in television elevational function is realized. The piston speed control technique is investigated to perform this experiment piston flow analysis and flow rate control for precise tubular cross section and propose a piston structure for elevation action. This study is for the development of the gas spring of the large size television stand with 50 inch over. In the gas spring development of elevation working, a device to compensate for the volume of the cylinder is generated as much the volume of the piston rod. As this study result, at the development of working gas spring, the hollow shaft is more favorable than the solid one in the apparatus to compensate for the cylinder volume generated.

The general auto transmission uses the torque converter that has a good vibration damping force by launching performance and damping effect as power transfer unit. The vehicle equipped with auto transmission uses Lock up clutch system to improve the fuel efficiency. The Lock up clutch system is the major factor of the devices that increase the torque from engine to transmission in specific condition and also consist of the damper springs to transfer the torque stably. Damper spring controls the vibration of power transfer units and improve the impression of riding and durability, by being damping function on change torque from engine. In addition, not only the appearance and performance, but also these sensitive qualities as like vibration and noise can also be main factor to buy a car. Recently, in order to absorb the low vibration caused by vehicle structure vibration, the Low-stiffness damper has been on the rise. The damper spring should be considered and designed, considering the engine characteristic and direct connect of lock up clutch due to the stiffness of the spring and hysteresis has a major effects to the damper characteristic. This study can be used for analyzing the major factors to effect the NVH characteristic by evaluating the damper’s hysteresis according to change of spring stiffness.

This paper shows the feasibility on the application of E-glass fiber/epoxy(GFRP) composite materials to an automotive leaf spring. In order to keep much lighter weight by replacing the steel with the composite material, it is important to optimize the material parameters and design variables consisting of the structure. This paper focused on the effects of material compositions and its fiber orientations for estimating the static behaviors of leaf spring. First of all, basic material properties of GFRP composite were measured by five types of coupon specimens from ASTM standard test. The reverse implementation was also done to obtain the complete set of in-situ fiber and matrix properties from ply test results. Finally, the static spring rates was examined for the variation of thickness and material parameters such as fiber angles and resin contents of composite leaf spring.

복합재료 사이에 주파수 선택적 투과막(Frequency Selective Surface)을 삽입하여 동시경화 공정을 이용하여 주파수 선택적 투과 기능을 가지는 하이브리드 복합재료를 성형하면 재료들 간의 열팽창 계수와 강성의 차이로 인해 구조 내에 잔류 열응력이 발생하게 되고, 이로 인하여 스프링 백 현상이 발생한다. 따라서 복합재의 적층에 따른 영향을 알아보기 위해 복합재료의 적층각을 선택적 투과막(Frequency Selective Surface)을 중심으로 대칭과 비대칭 적층으로 적용하여 하이브리드 구조의 잔류 열응력을 예측하고, 이에 대한 스프링 백에 대해서 연구하였다.

The purpose of this study was to analyze of the upper extremities joint momet during handspring. The conclusion of this study were as follows First, Handspring touched on the hand when operating the landing, when the body becomes rigid, while the isometri

This paper proposes a software development evaluation index for the productivity related to Spring 2.5 and EJB 3.0 with same lightweight container architecture. Spring is a known successful open source standard model for lightweight container architecture. EJB in an enterprise environment as a standard framework is most commonly used in production. However, there is no comparison research about the performance of Spring 2.5 and EJB 3.0 with same identical platform. Quantitative analysis is supported as a part of LoC(Line of Code) analysis. There is a limit to develop the updated software with no the specific evaluating index for the productivity of the software. In this study, the development platform environment based on the same database schema system Spring 2.5 and EJB 3.0 is in the design and implementation. In addition, comparison and standardization of software development productivity assessment is to provide guidance.

형상기억합금의 복원력 및 복원량은 열 하중 및 기계적 하중으로 인한 마르텐사이트 상에서 오스테나이트 상으로의 상 변이에 의한 상변형률 발생에 기인한다. 복원력 및 복원량은 초기 형상 및 하중 부여 방식에 따라 차이가 발생하는데 적절 한 설계 전략없이 상변형률에만 의지한 경우 큰 복원력은 발생할 수 있어도 큰 복원량을 기대하기는 어렵다. 이는 형상기 억합금의 큰 복원력과 작은 복원량 간의 비대칭성에 기인하며 형상기억합금의 효율적인 이용에 걸림돌이 된다. 본 연구에 서는 형상기억합금의 상변이로 발생하는 복원량을 극대화하는 방안으로 형상기억합금 선이 이중으로 감겨있는 이중 나선 구조 형상기억합금 스프링을 제안한다. 그리고 열 하중에 의해 발생하는 복원량을 예측하고 단일 나선 구조 형상기억합금 스프링과 비교 분석하여 이중 나선 구조 형상기억합금 스프링이 단일 나선 구조 형상기억합금 스프링보다 성능 비대칭성 을 보다 완화시킬 뿐만 아니라 복원력 대비보다 큰 복원량을 가짐을 보였다.

Belleville springs can sustain relatively large loads with small deflections and belleville spring washers are especially suited for high loads in small places. Belleville springs are used singly or in stacks to achieve desired load such as power transmission components. The aim of this paper is to design for the belleville spring diameter and thickness to minimize volume of the system. The design is carried out using finding solution in a commercial spreadsheet application software, Microsoft Excel 2007. The numerical results are obtained where the displacement, stress and load in the spring are treated as constraints function.