The objective of this study was to determine the effect of injection application of pig slurry on ammonia (NH3) and nitrous oxide (N2O) emission from timothy (Phleum pretense L.) sward. The three treatments were applied: 1) only water as a control, 2) pig slurry application by broadcasting, 3) pig slurry application by injection. The pig slurry was applied at a rate of 200 kg N ha-1. Total NH3 and N2O emission, expressed as a cumulative amount throughout the measurement time (40 days), was 2.68 kg NH3-N ha-1 and 6.58 g N2O-N ha-1, respectively, in the control. The injection application of pig slurry decreased total NH3 and N2O emission by 39.8% and 33.3%, respectively, compared to broadcasting application of pig slurry. The present study clearly showed that injection application exhibited positive roles in reducing N losses through NH3 and N2O emission.

본 연구 결과, 숙성처리는 지황의 비소화성 당류의 분해로 환원당이 증가하고, 쓴 맛의 원인인 카탈폴을 감소시킴으로서 지황의 소화성과 단맛의 증가에 긍정적인 영향을 줄 수 있을 것으로 생각되며, 비소화성 당류로부터의 환원당 증가와 카탈폴 감소를 위한 최적 온도는 각각 50℃와 30~40℃이었다. 따라서 본 연구에서 제안하는 숙성처리가 낮은 소화성과 쓴맛으로 인해 활용성이 낮은 지황의 소화성과 관능적 품질 개선에 활용될 수 있을 것으로 판단된다.

In the present study, we evaluated the effect of pH modulation on concentrations of odorous compounds and pollutants in pit slurry from pig operation building. A slurry sample was taken from the pit of a pig operation building where 50 finishing pigs [(Landrase × Yorkshire) × Duroc] were kept. Three levels of pH (6, 8 and 10) were measured and adjusted daily during the incubation periods using chemical reagents of 1 N HCl or 3 N NaOH. Concentrations of odorous compounds and pollutants were analyzed from slurry incubated for 7 days. When these material concentrations were compared with the pH 8 slurry which was the pH of pit slurry, levels of short chain fatty acids, indoles and total organic carbon were reduced 7%, 68% and 2%, respectively, in the pH 6 treatment (P<0.05). Ammonium nitrogen, phenols and total nitrogen concentrations were lower by 31%, 18% and 17%, respectively, than with the pH 10 slurry (P<0.05). When the odor contribution in pH treatments was assessed according to the odor activity value, it was found to be 23% lower in the pH 6 treatment compared with pH 8. The pH modulation would affect odor emissions and microbial activity from pit slurry. Although not all odorous compounds showed the reduction effect with the same pH control, this study can be effectively used as base data when using additives for pH control.

The present study demonstrates the effect of raw powder on the pore structure of porous W-Ni prepared by freeze drying of camphene-based slurries and sintering process. The reduction behavior of WO3 and WO3-NiO powders is analyzed by a temperature programmed reduction method in Ar-10% H2 atmosphere. After heat treatment in hydrogen atmosphere, WO3- NiO powder mixture is completely converted to metallic W without any reaction phases. Camphene slurries with oxide powders are frozen at −30 oC, and pores in the frozen specimens are generated by sublimation of the camphene during drying in air. The green bodies are hydrogen-reduced at 800 oC and sintered at 1000 oC for 1 h. The sintered samples show large and aligned parallel pores to the camphene growth direction, and small pores in the internal wall of large pores. The strut between large pores, prepared from pure WO3 powder, consists of very fine particles with partially necking between the particles. In contrast, the strut densification is clearly observed in the Ni-added W sample due to the enhanced mass transport in activation sintering.

Porous Cu with a dispersion of nanoscale Al2O3 particles is fabricated by freeze-drying CuO-Al2O3/camphene slurry and sintering. Camphene slurries with CuO-Al2O3 contents of 5 and 10 vol% are unidirectionally frozen at -30oC, and pores are generated in the frozen specimens by camphene sublimation during air drying. The green bodies are sintered for 1 h at 700oC and 800oC in H2 atmosphere. The sintered samples show large pores of 100 μm in average size aligned parallel to the camphene growth direction. The internal walls of the large pores feature relatively small pores of ~10 μm in size. The size of the large pores decreases with increasing CuO-Al2O3 content by the changing degree of powder rearrangement in the slurry. The size of the small pores decreases with increasing sintering temperature. Microstructural analysis reveals that 100-nm Al2O3 particles are homogeneously dispersed in the Cu matrix. These results suggest that a porous composite body with aligned large pores could be fabricated by a freeze-drying and H2 reducing process.

The objective of this study was to determine the effect of nitrification inhibitor dicyandiamide (DCD) and urease inhibitor hydroquinone (HQ) on ammonia (NH3) and nitrous oxide (N2O) emission from pig slurry applied to Timothy (Phleum pretense L.) sward. The daily emission of ammonia (NH3) and nitrous oxide (N2O) was monitored for 9 days in three different treatments; 1) control (only pig slurry application), 2) DCD treatment (pig slurry + DCD), and 3) HQ treatment (pig slurry + HQ). Most NH3 emission occurred after 4~5 days in three treatments. Total NH3 emission, expressed as a cumulative amount throughout the measurement time, was 1.33 kg N ha 1 in the control. The DCD and HQ treatment decreased total NH3 emission by 16.3% and 25.1%, respectively, compared to the control. Total N2O emission in the control was 47.1 g N ha 1. The DCD and HQ treatment resulted in a reduction of 67.9% and 41.8% in total N2O emission, respectively, compared to the control. The present study clearly indicated that nitrification and urease inhibitor exhibited positive roles in reducing N losses through NH3 and N2O emission.

This study was conducted to assess the efficacy of slurry acidification in reducing ammonia emission from manure storage and application. The non-fermented cattle manure (NFC) and swine slurry (SS) were acidified by sulfuric acid and stored in an acryl chamber for 168 and 96 hours, respectively. Ammonia emitted from the chamber was collected using an acid trap system. The amount of ammonia emission was significantly reduced when the livestock manures were treated with sulfuric acid. The absolute amount of ammonia in NFC increased rapidly starting from 48 h and 72 h in the control (pH 8.6) and acidified NFC (pH 6.5), respectively. The absolute amount of ammonia was the highest at 96 h (3.65 g kg ¯¹ h ¯¹) in the control and at 144 h (2.34 g kg ¯¹ h ¯¹) in pH 6.5 NFC. The cumulative ammonia content in the control continuously increased until 96 h and was maintained until 168 h, whereas the increase rate of emission gas accumulation in acidified NFC was much less throughout the experimental period. Acidification of SS mitigated ammonia emission as proven in NFC. The cumulative amount of ammonia emission was decreased by 49.4% and 92.3% in the acidified SS at pH 6.5 and pH 5.5, respectively, compared to the control at 96 h after treatment. These results indicate that ammonia emission can be significantly reduced by sulfuric acid treatment of livestock manure during processing and the subsequent land application.

Metallic porous materials have many interesting combinations of physical and geometrical properties with very low specific weight or high gas permeability. In this study, highly porous Cu foam is successfully fabricated by a slurry coating process. The Cu foam is fabricated specifically by changing the coating amount and the type of polyurethane foam used as a template. The processing parameters and pore characteristics are observed to identify the key parameters of the slurry coating process and the optimized morphological properties of the Cu foam. The pore characteristics of Cu foam are investigated by scanning electron micrographs and micro-CT analyzer, and air permeability of the Cu foam is measured by capillary flow porometer. We confirmed that the characteristics of Cu foam can be easily controlled in the slurry coating process by changing the microstructure, porosity, pore size, strut thickness, and the cell size. It can be considered that the fabricated Cu foams show tremendous promise for industrial application.

PURPOSES: Recently, crack, rutting, and stripping problems from the surface of asphalt pavements in National highway are observed and they affect the drivers to feel uncomfortable on the road. Surface treatments are recommended to use in distressed pavements due to costeffective, and improvement of surface performance. The purpose of this study is to evaluate the performance of micro-surfacing and polymer slurry seal treatments for distressed asphalt pavements. METHODS: Surface conditions and friction resistance are evaluated for asphalt pavements treated with micro-surfacing and polymer slurry seal mixes in National highway 30 line and 34 line. Visual observation is conducted and surface performance is measured by PES (Performance Evaluation Surveyor) in terms of crack ratio, rutting and IRI(International Roughness Index). BPN(British Pendulum Number) is measured by BPT(British Pendulum Tester) to evaluate the friction resistance in the field. RESULTS: The surface evaluation results are presented for asphalt pavement treated with micro-surfacing and polymer slurry seal treatments in National highway 30 line and 34 line. Based on the visual observation, micro-surfacing and polymer slurry seal treatments show better improvements in terms of cracks and stripping. Based on the surface conditions measured by PES vehicle, the surface performance of microsurfacing treatments improves from 53.3% to 54.2% and the surface performance of polymer slurry seal treatments improves from 21.6% to 59.7%. However, the friction resistance of both micro-surfacing and polymer slurry seal treatments decreases from 2.5% to 6.7%. Further, it should be verified to produce the surface exposed with aggregates during the construction process of both treatment methods in the field. CONCLUSIONS : Based on the performance evaluation results in the filed, the surface performance of asphalt pavement treated with micro-surfacing and polymer slurry seal treatments improves from 21.6% to 59.7%. While, the friction resistance of asphalt pavement treated with micro-surfacing and polymer slurry seal treatments does not improve. It can be concluded that current micro-surfacing and polymer slurry seal treatments would improve surface performance but would not improve the friction resistance.

This paper proposes a novel way of fabricating aligned porous Sn by freeze-drying of camphene slurry with stannic oxide (SnO2) coated Sn powders. The SnO2 coated Sn powders were prepared by surface oxidation of the initial and ball-milled Sn powders, as well as heat treatment of tin chloride coated Cu powders. Camphene slurries with 10 vol% solid powders were prepared by mixing at 50 oC with a small amount of oligomeric polyester dispersant. Freezing the slurry was done in a Teflon cylinder attached to a copper bottom plate cooled at −25 oC. Improved dispersion stability of camphene slurry and the homogeneous frozen body was achieved using the oxidized Sn powder at 670 oC in air after ball milling. The porous Sn specimen, prepared by freeze-drying of the camphene slurry with oxidized Sn powder from the heat-treated Sn/tin chloride mixture and sintering at 1100 oC for 1 h in a hydrogen atmosphere, showed large pores of about 200 μm, which were aligned parallel to the camphene growth direction, and small pores in their internal walls. However, 100 μm spherical particles were observed in the bottom part of the specimen due to the melting of the Sn powder during sintering of the green compact.

Metal foams have a cellular structure consisting of a solid metal containing a large volume fraction ofpores. In particular, open, penetrating pores are necessary for industrial applications such as in high temperature filtersand as a support for catalysts. In this study, Fe foam with above 90% porosity and 2 millimeter pore size was suc-cessfully fabricated by a slurry coating process and the pore properties were characterized. The Fe and Fe2O3 powdermixing ratios were controlled to produce Fe foams with different pore size and porosity. First, the slurry was preparedby uniform mixing with powders, distilled water and polyvinyl alcohol(PVA). After slurry coating on the polyure-thane(PU) foam, the sample was dried at 80℃. The PVA and PU foams were then removed by heating at 700℃ for 3hours. The debinded samples were subsequently sintered at 1250℃ with a holding time of 3 hours under hydrogenatmosphere. The three dimensional geometries of the obtained Fe foams with an open cell structure were investigatedusing X-ray micro CT(computed tomography) as well as the pore morphology, size and phase. The coated amount ofslurry on the PU foam were increased with Fe2O3 mixing powder ratio but the shrinkage and porosity of Fe foams weredecreased with Fe2O3 mixing powder ratio.