The removal efficiency of VOC was tested for five air cleaners selected in terms of type and cleaning performances. Toluene, representative VOCs, was selected and used as the test gas. In order to indicate toluene removal capacity, toluene removal efficiency in a chamber and a duct was investigated with different measurement devices such as gas detecting tubes and GC/MSD. Changes in toluene concentration in the chamber were measured with GC/MSD. The test results showed that the performances of the test models in the test chamber were superior to those in the duct, however, they did not differentiate the performances of test models. According to our test study, toluene removal capacity calculated from the changes in toluene concentration with time was a good indicator for VOCs removal performance.

The deodorization performances of ammonia, acetic acid and acetaldehyde were tested for each of all forty five air cleaners sold in the online shops and department stores. The removal performances of toluene and formaldehyde were also investigated and the results were compared to the deodorization performances for the air cleaners. Filter-type and complex type air cleaners which used activated carbon filters showed superior in odor removal performances to those of ionizer type and wet type air cleaners. Toluene and formaldehyde were readily removed for the most of filter-type and complex type air cleaners. Ionizer air cleaners had little removal ability for the toluene and formaldehyde.

The characteristics of adsorption and desorption of benzene and toluene were investigated at a fixed bed packed with the activated carbon and activated carbon fiber. Through breakthrough experiments under various feed concentration conditions, it was found that the slope of mass transfer zone and the tailing in the breakthrough curves were different from the feed conditions due to different heats of adsorption. In hot nitrogen desorption, the regeneration time and mass transfer zone of the toluene desorption curve were longer than those of the benzene desorption curve because of the difference in adsorption affinity. With an increase in the regeneration temperature, the height of roll-up and the sharpness of desorption curves increased but the regeneration times decreased. The adsorption capacities of the activated carbon and activated carbon fiber after three-time thermal regenerations decreased about 25% and 37% for benzene and 18% and 25% for toluene, respectively. To investigate the effect of the regeneration temperature on the energetic efficiency, the characteristic desorption temperatures of toluene and benzene were investigated by calculating purge gas consumption and temperature.

The VOCs(Volatile Organic Compounds) is one of the major cause for the atmosphere pollution. Breakthrough behavior of benzene and toluene in adsorption bed packed with activated carbon was experimentally studied. Composition and temperature of the gas flowing in the bed was measured and breakthrough curves for each component was obtained. Breakthrough time of benzene was earlier than that of toluene due to relatively weak adsorptivity. The relationship between breakthrough time and flow rate was obtained. The shape of temperature change with time was dependent on the position in the bed. Temperature changed faster and sharper in the inlet than in the outlet. It was noted that breakthrough behavior could be affected by the heat transfer properties.

In the separation of toluene/n-heptane mixture by the emulsion type liquid membrane in a batch system, the effect of surfactants on the separation factor and membrane stability were studied over the surfactant concentration ranging from 0.1 to 1.5 wt% at the contact time of 5 and 10 minutes and the settling time 5 and 10 minutes. The surfactants used were triethanol amine lauryl sulfate. The separation factor reached its maximum value at the surfactant concentration of 0.5 wt%. It was found that the percentage of membrane breakup reached its minium values and the separation factor showed its maximum value at the surfactant concentration of 0.5 wt%, which confirmed that efficient separation could be effect when emulsion liquid membrane were stable because of low membrane break up.

In the separation of toluene/n-heptane mixture by the emulsion type liquid membrane in an batch system, the effect of surfactant on the separation factor and membrane stability was studied over the surfactant concentration ranging form 0.1 to 1.5wt％ at the contact time of 5 and 10 minutes. and the settling time of 5 and 10 minutes. The surfactant used was sodium lauryl sulfate. The separation factor reached its maximum value at the surfactant concentration of 0.5wt％ for surfantant. It was found that the percentage of membrane breakup reached its minimum values and the separation factor showed its maximum value at the surfactant concentration of 0.5wt%. which confirmed that efficient separation could be effect when emulsion liquid membrane was stable because of low membrane breakup.

Ulmus davidiana Nakai (UDN) has been traditionally used as a herbal medicine to treat inflammatory diseases in Korea. In the present study, we investigated the anti-ecotoxic potential of a 116 kDa glycoprotein isolated from UDN (UDN glycoprotein) in human intestinal epithelial INT-407 cells. We demonstrated that UDN glycoprotein (20 μg/mL) could inhibit the production of lactate dehydrogenase (LDH) induced by toluene, an ecotoxic substance. Additionally, we found that the toluene-induced intestinal cytotoxicity was mediated by the phosphorylation of p38 Mitogen-Activated Protein Kinase (MAPK) via the production of intracellular Reactive Oxygen Species (ROS). The UDN glycoprotein significantly decreased the levels of ROS production and p38 MAPK activation in toluene-stimulated INT-407 cells. Moreover, the UDN glycoprotein inhibits the phosphorylation of nuclear factor-kappa B (NF-κB), which is responsible for the production of LDH, in toluene-stimulated INT-407 cells. Collectively, our data indicate that UDN glycoprotein is a natural antioxidant and a modulator of ecotoxicity signaling pathways in human intestinal epithelial cells.

The photocatalytic decomposition characteristics of toluene, acetone, and methyl mercaptan (MM) by UV reactor installed with TiO2-coated perforated plane were studied. The removal efficiency of single toluene, acetone, and MM vapor was increased with increasing oxygen concentration, but decreased with increasing inlet concentration. Elimination capacity of single toluene, acetone, and MM vapor was obtained to be 628 g/m3․day, 1,041 g/m3․day, and 2,158 g/m3․day, respectively. Also, the photocatalytic decomposition of binary vapor consisted of toluene and acetone, toluene and MM, acetone and MM were observed. Elimination capacity of toluene mixed with acetone, toluene mixed with MM, acetone mixed with toluene, acetone mixed with MM, MM mixed with toluene, and MM mixed with acetone was 327 g/m3․day, 512 g/m3․day, 128 g/m3․ day, 266 g/m3․day, 785 g/m3․day and 883 g/m3․day, respectively. The inhibitory effect of acetone was higher than MM in photocatalytic decomposition of toluene, the inhibitory effect of toluene was higher than MM photocatalytic decomposition of acetone, and the inhibitory effect of toluene was higher than acetone in photocatalytic decomposition of MM.

In this study, the photocatalytic decomposition characteristics of single toluene, toluene mixed with benzene, toluene mixed with acetone, and toluene mixed methyl mercaptan (MM) by UV reactor installed with TiO2-coated perforated plate were studied. The photocatalytic decomposition rate of single toluene, toluene mixed with benzene, toluene mixed with acetone, and toluene mixed with MM fitted well on Langmuir-Hinshelwood (L-H) kinetics equation. The maximum elimination capacity was obtained to be 628 g/m3·d for single toluene, 499 g/m3·d for toluene mixed with benzene, 318 g/m3·d for toluene mixed with acetone, and 513 g/m3·d for toluene mixed with MM, respectively. The negative effect in photocatalytic decomposition of toluene are found to be in the order of acetone>benzene>MM.

Alumina-supported catalysts containing different transition metals such as Cu, Cr, Mn, Zn, Co, W were investigated for their activity in the selective oxidation of toluene. Catalytic oxidation of toluene was investigated at atmospheric pressure in a fixed bed flow reactor system over transition metals with Al2O3 catalyst. The result showed the order of catalytic activities for the complete oxidation of toluene was Mn > Cu> Cr> Co> W> Zn for 5wt.% transition metals/Al2O3. Mn/Al2O3 catalysts containing different amount of Mn were characterized by X-ray diffraction spectroscopy for decision of loading amount of metal to alumina. 5 wt.%Mn/Al2O3 catalyst exhibits the highest catalytic activity, over which the toluene conversion was up to 90% at a temperature of 289℃.

The purpose of this work is to study the adsorption and desorption characteristics of acetone vapor and toluene vapor from adsorption tower in the VOCs recovery device. The six kinds of activated carbon with different pore structures were used and the adsorption and desorption characteristics were compared according to pore structure, desorption temperature, and adsorption method, respectively. Adsorption capacity of acetone vapor and toluene vapor by batch method was higher than that by dynamic method. Especially, activated carbon with medium-sized or large pores had more difference in adsorption capacity according to adsorption methods as a result of gradually condensation of vapors on relatively mesopore and large pores. Activated carbons with relatively large pores and relatively small saturated adsorption capacity had excellent desorption ability.

Unlike water applications, the photocatalytic technique utilizing light-emitting-diodes as an alternative light source to conventional lamp has rarely been applied for low-level indoor air purification. Accordingly, this study investigated the applicability of UV-LED to annular-type photocatalytic reactor for removal of indoor-level benzene and toluene at a low concentration range associated with indoor air quality issues. The characteristics of photocatalyst was determined using an X-ray diffraction meter and a scanning electron microscope. The photocatalyst baked at 350 ℃ exhibited the highest photocatalytic degradation efficiencies(PDEs) for both benzene and toluene, and the photocatalysts baked at three higher temperatures(450, 550, and 650 ℃) did similar PDEs for these compounds. The average PDEs over a 3-h period were 81% for benzene and close to 100% for toluene regarding the photocatalyst baked at 350 ℃, whereas they were 61 and 74% for benzene and toluene, respectively, regarding the photocatalyst baked at 650 ℃. As the light intensity increased from 2.4 to 3.5 MW cm-1, the average PDE increased from 36 to 81% and from 44% to close to 100% for benzene and toluene, respectively. In addition, as the flow rate increased from 0.1 to 0.5 L min-1, the average PDE decreased from 81% to close to zero and from close to 100% to 7% for benzene and toluene, respectively. It was found that the annular-type photocatalytic reactor inner-inserted with UV-LEDs can effectively be applied for the decomposition of low-level benzene and toluene under the operational conditions used in this study.

Toluene desorption of modified activated carbon for microwave irradiation was evaluated. As a virgin GAC reacted from microwave energy, it created an "arcing" between GAC particles in desorption process. The arcing became more and more vigorous and achieved a red flame of GAC. The silica coated GAC(Si/GAC) was developed to prevent arcing phenomenon and temperature control problem. The result shows virgin GAC with 5wt%, 10wt% and 20wt% silica had no arcing and could control temperature very well. However, the adsorption rate of Si/GAC was decreased by coated silica amount due to decreasing surface area of GAC. The 5wt% Si/GAC adsorption rate was quite similar to virgin GAC adsorption rate. After adsorption, the toluene-loaded GAC and Si/GAC was reactivated by 2450MHz MW irradiation with 300W for 5 min. Quantitative desorption of the toluene was achieved at MW irradiation at 300W with desorption efficiencies as high as 98.59% to 84.65%% after four cycles.