In this paper, it is covered in detail the process of generating structural alternatives with geometry change and its optimization by StrAuto. The main roof structure of the Exhibition Center is modelled parametrically and the optimal alt is derived by observing volume changes according to geometry change of main roof truss. Existing studies performed optimization process through sections and properties due to the limitations of shape change, but this study have meaning of performing the optimization with geometry changes which is the most critical skills of StrAuto. By the process of securing a sufficient margin by geometry changes and reducing volume with the optimization of sections, despite of a partial optimization of large space structure, it could be reduced by 11.7% of the total volume.

Floating PV generation system, renewable energy power plant, is able to overcome the disadvantages of ground PV generation system and improve generating efficiency. The frame structural system is an established technology among a diversity of structural technologies which has been developed for related fields. In this paper, the both structural safety and characteristics of floating PV generation structures depend on the different placement angle of solar module are investigated to improve the commercial viability, the structural safety, and characteristics of floating PV generation structures. In addition, for the estimation of structural safety, FE analyses are conducted. From the results, the lower placement angle of solar module improves the structural safety of floating PV generation system.

본 연구에서는 쌍동형 카페리에 대한 기본 구조 설계 및 구조 해석을 위한 기법을 제시한다. 카페리와 같이 길이 50미터 이상 길이와 폭/ 비가 12보다 큰 중/소형 고속 선박의 강도 해석에 대한 규정이나 방법론은 아직까지 명확하게 제시되지 않고 있다. 따라서 본 논문에서 부재의 스캔 틀링은 한국선급기준을 적용하였고, 설계안에 대한 구조강도 검증을 위해서 카페리 전용선박 기준에 의해 추가적으로 검증하였다. 특히, 카페리 전 용선박 기준을 적용하여, Hull girder ultimate strength를 추가적으로 수행하여, 현재 기준에 의한 설계의 모호성을 극복하도록 제안하였다. 본 연구를 통해 도출된 연구 결과는 앞으로 고속 쌍동형 카페리의 구조설계 및 구조해석에 관련된 기본적인 자료로 유용하게 활용될 것으로 예상된다.

Numerical analysis has been carried out to investigate the structural characteristics of auxiliary shaft system in a compact special vehicle. Stress and deformation distributions with safe factor in the auxiliary axle system are compared. It can be seen that maximum stress happens near the local axle position and deformation at the air spring is also predicted. The results from this study could be applicable for optimal design of variable shaft system in the compact special vehicle.

The objective of this paper is to suggest structural design for the long-life housing apartment complex to save the construction cost. The key is to use unavailable underground space due to bearing walls or bad configuration of columns in apartments as the parking space. Therefore, the structural plan of apartment buildings considering the parking section in the underground should be designed. After analytical resutls of three cases, it is significant effect in saving construction cost.

The result of the previous work leads to the idea that the inner area of the hyperbolic shell generator should be minimized for the cooling tower with higher first natural frequency. In this study the inner area of the hyperbolic shell generator was graphically established under varying height of the throat and angle of the base lintel. From the graph, several shell geometries were selected and analysed in the aspect of the natural frequency. Three representative towers reinforced differently due to different first natural frequencies were analysed non-linearly and evaluated using a damage indicator based on the change of natural frequencies. The results demonstrated that the damage behaviour of the tower reinforced higher due to a lower first natural frequency was not necessarily advantageous than the others

본 연구에서는 간척지에서 플라스틱 온실의 기초안전성을 평가하기 위하여 강재 나선말뚝기초를 갖는 폭 6m 연동하우스 1개동과 강재 나선말뚝기초와 파이프줄기초를 각각 적용한 폭 8.2m 단동하우스 2개동을 SPT N값 이 2인 간척지 시험포장에 설치하여 플라스틱 온실의 인발량 및 침하량을 측정하였다. 또한 플라스틱 온실에 적용된 나선말뚝기초 3종(φ50, φ75 및 φ100)을 인근의 간척지 시험포장에 설치하여 인발저항특성을 시험하였다. 평가 기간 중 플라스틱 온실의 수직변위 움직임이 관측 되었지만 온실의 규모와 비교하여 그 변위는 무시할만한 수준이었다. 평가 기간 중의 최대 수직변위는 나선말뚝 기초를 적용한 연동하우스의 경우 +9.0mm(인발)~- 11.5mm(침하), 나선말뚝기초를 적용한 단동하우스의 경 우 +1.3mm~-7.7mm, 파이프줄기초를 적용한 단동하우스 의 경우 +0.9mm~-11.2mm로 나타났다. 나선말뚝기초의 허용인발력은 모두 극한하중 판정기준에 의해 판단할 수 있었으며 φ50mm, φ75와 φ100 나선말뚝기초의 최종 허용인발력은 각각 0.40kN, 1.0kN과 2.5kN으로 산정할 수 있었다. 평가기간 중 나선말뚝기초를 적용한 플라스틱 온실의 기초안전성을 최종적으로 판단하기에는 다소 무리가 있다고 판단되나 강재 나선말뚝기초를 간척지 플라스틱 온실의 기초로 사용하더라도 큰 문제는 없을 것으로 판단되었다.

The findings were summarized as follows. The safety check by manufacturer showed that 6 of 13 companies are over the average occurrence of defects. It was expected that there would be a difference between manufacturing technology capability and production system of each manufacturer. Consequently, manufacturers should institutionally improve and strengthen certification items for the upward standardization of safety certification before factory. Second, the safety check by year showed that the results of this study accord with those of previous studies on defect time. Consequently, manufacturers should classify the 3-year-old equipment for vehicle-mounted MEWP into a special check subject to do a nondestructive test according to proven results, and also reflect the test in a safety test system to do regular preventive activities of equipment defects. Third, the safety check by part showed that the boom and outrigger parts of vehicle-mounted MEWP have the most defects. Stress concentration resulted in defects as the boom part was most frequently operated in the structural parts for a real work. To prevent this, it is suitable to improve the hardness of boom materials. The outrigger part needs improvement in safety devices with materials. As an outrigger supports the overturning moment of equipment, it is most affected by its load based on the operating radius, resulting in fatigue crack.

Natural and expandable graphites were chemically treated in acidic aqueous solutions such as acetic acid or mixtures of acetic acid and nitric acid. Structures and thermal conductivities of the as-treated graphites were characterized in detail. Both graphites were significantly oxidized in the mixed acidic solution of H2SO4 and HNO3, which condition was generally used for the oxidation of carbon nanotubes. This considerable oxidation of graphites caused a depression of their thermal conductivity. The structural characteristics, obtained by XRD and XPS, show that the graphites treated in the relatively weak acidic conditions (acetic acid or mixture of acetic acid and nitric acid) were quite similar to the untreated graphites. However, the thermal conductivities of both acidic-treated graphites were remarkably increased.

PURPOSES: This study is primarily focused on evaluating the effects of the non-linear stress-strain behavior of RAP concrete on structural response characteristics as is applicable to concrete pavement. METHODS : A 3D FE model was developed by incorporating the actual stress-strain behavior of RAP concrete obtained via flexural strength testing as a material property model to evaluate the effects of the non-linear stress-strain behavior to failure on the maximum stresses in the concrete slab and potential performance prediction results. In addition, a typical linear elastic model was employed to analyze the structural responses for comparison purposes. The analytical results from the FE model incorporating the actual stress-strain behavior of RAP concrete were compared to the corresponding results from the linear elastic FE model. RESULTS : The results indicate that the linear elastic model tends to yield higher predicted maximum stresses in the concrete as compared to those obtained via the actual stress-strain model. Consequently, these higher predicted stresses lead to a difference in potential performance of the concrete pavement containing RAP. CONCLUSIONS : Analysis of the concrete pavement containing RAP demonstrated that an appropriate analytical model using the actual stress-strain characteristics should be employed to calculate the structural responses of RAP concrete pavement instead of simply assuming the concrete to be a linear elastic material.

본 연구는 벤처창업기업의 대표자 기술혁신역량과 경영진의 전문화, 기술사업 투 자계획의 타당성 등이 기업의 경영성과인 재무건전도와 나아가 부실화가능성에 미치는 영향에 대하여 구조방정식 모델(SEM)을 이용한 실증분석을 실시하였다. 본 연구는 2011년∼2012년 2 년 동안 1,419개 표본기업에 대한 기술보증기금 기술평가 전문가들의 현장평가 데이터와 기업 현황 조사정보 및 재무정보 등을 활용하였으며, 설립후 7년이내 기술력 기반의 벤처기업들 속성 상 ‘고위험⋅고수익’으로써 여타기업보다 부실화가능성이 높은 기업군인 점을 감안하여 이들 기 업을 연구대상으로 설정하였다. 분석 결과, 대표자의 풍부한 경험과 기술지식 등 기술혁신역량 과 경영진의 분야별 전문화를 바탕으로 한 체계적 조직운영, 그리고 적정규모의 기술사업 투자 ⋅재무관리 계획수립 및 합리적 추진 등을 통하여 기업의 성장성과 수익성 등 기업의 전반적인 재무건전도를 향상시키고, 나아가 단기적 부실화리스크도 감축시키는 것으로 확인되었다.

본 연구에서는 페이즈필드 설계법에 기반한 형상최적설계를 통해 개선된 패치안테나 금속 패치 부분의 형상 설계를 진행 하였다. 설계 목적은 패치 안테나의 목적 주파수에서의 방사 효율을 최대화 하는 것으로 설정하였고, 이에 따라 목적 함수는 반사손실을 나타내는 S-파라미터 값의 최소화로 정의하였다. 패치형상의 최적화 결과는 페이즈필드 설계법을 이용하여 도 출하였고, 최적화 결과의 회색영역을 제거하기 위해서 컷오프 방법을 적용하였다. 더불어 쿼터 정합기의 길이 변화를 통해 성능 개선 과정을 진행하였다. 이를 통해 도출해낸 최종 형상에 대한 해석 결과, 목표 주파수에서의 S-파라미터 값이 -1.14dB에서 -12.73dB로 개선됨을 확인하였다.

본 논문에서는 온실 구조물의 구조 성능 검토 시 적합한 모델링 방법을 제시하기 위해 대상 온실 구조물을 선정하고 지점 및 접합부 조건 그리고 케이블 요소의 단면적을 변화시켜 가며 파라메트릭 스터디를 수행하였으며, 이들 파라메터의 변화에 따른 대상 구조물의 주요 모드 형상 및 고유진동수 변화를 조사하였다. 또한 대상 구조물에 대해 현장 가속도계 측정법을 이 용하여 상시진동을 계측하여 주요 모드 형상 및 고유진동수를 측정하여 해석 결과와 비교하였다. 이들 비교 결과로부터 대 상 온실 구조물의 해석에 적합한 모델링 기법을 제시하였다.

Structural dynamic system involves random variables conditions such as material property, geometric parameters and applied loads. This uncertainties result from the structural parameter are carefully considered the dynamic structural response in displacement, stress, and natural frequencies. The random vibrational system must be designed to withstand a certain amount of the fluctuation with respect to the uncertainties. Harmonic response of a spring-mass system is mathematically modelled with the probabilistic finite element method using the Monte Carlo simulation. The aim of this paper is to find the optimal lowest frequency for the spring-mass system with random input variables and response parameters to the displacements. The probabilistic design is carried out using ANSYS probabilistic design module in a commercial application software and then the optimal design is sequentially solved. An efficient and practical optimal design evaluation method is proposed for the design of the harmonic system. The numerical results are obtained where the next highest frequency of the system and displacements treated as constraints.

The technique of VR and AR utilizing HMD and peripherals was due to launch the products in which the research developers predicting the market magnification satisfy the request of the users in 2016. In the suddenly change game market, because of reflecting global technique and standardization trend, the white paper on Korean games and ICT standardization roadmap published for the development of Korea game industry are important in the decision procedure of the prediction of the game industry and game marketing and technology development and standardization support policy related to the game. In this paper, I analyze the present condition of Korean game industry through published white paper on Korean games and ICT standardization roadmap since 2012 by the year 2016 and suggested the competitiveness strengthening measure of Korean game industry required for the pathfinding of the global game market.