본 연구에서는 H-Beam 부재에 TRM(Total Reinforced Member)공법의 적용을 통한 부재의 구조성능개선에 대하여 분석하였다. TRM공법은 가교의 성능개선을 위해 적용되는 여러 공법 중 프리스트레스 도입을 통해서 H-Beam 부재의 구조성능을 개선하는 공법이다. 우선 본 연구에서는 해석적인 시뮬레이션을 통해서 TRM공법의 적용 가능성을 확인하였다. 1차적으로 수치 해석을 통해서 프리스트레스 도입을 위한 선행하중을 결정하고, 순수 H-Beam 부재와 L형 강재가 용접된 부재 그리고 TRM공법이 적용된 3가지의 부재에 대한 구조성능 변화를 해석을 통해서 확인하였다. 그리고 해석적인 결과의 검증 및 공법의 현장적용 가능성을 평가하기 위하여 순수 H-Beam 부재와 TRM공법이 적용된 2가지의 부재에 대한 3점 굽힘 시험을 수행하였다. 실험을 통하여 TRM공법이 적용된 부재에서 순수 H-Beam 부재대비 하부 플랜지의 발생응력 및 최대처짐이 각각 20.60%, 16.87% 감소 하는 결과를 확인하였다.

본 연구는 요철형 암반굴착 락볼트 공법에 관한 것으로 암반 확공굴착 드릴비트를 이용하여 실험체를 제작하고, 요철이 없는 모델과 요철을 형성시킨 모델의 인발저항 성능을 평가하기 위한 실험방법을 제시하고 실물실험을 통해 요철형 암반 굴착 락볼트의 성능을 평가하였다. 요철형성 모델은 슬립이 일어나기 전 암석의 취성파괴가 발생하였으며, 무형성 모델보다 평균 1.65배의 저항효과를 보였고 그라우트로 충전된 요철은 압축력에 의해 그라우트가 파괴되더라도 암석 내에서의 2차적인 인장저항효과를 보였다. 또한, 요철의 깊이가 150mm일 경우는 60mm의 경우보다 약 1.12배 인발저항효과를 나타내었다. 암석의 취성으로 인해 암석과 그라우트간의 부착력이 상대적으로 큰 것으로 나타났으며, 반복적이고 균일한 실험결과의 도출은 불가능 했으나 요철형성 효과에 대한 충분한 검증이 이루어졌다. 향후 요철의 길이나 개수 등의 변수에 따른 추가실험과 성능평가를 통해 최적의 요철형성 설계가 가능할 것으로 판단된다.

자연재해 발생을 예방하기 위한 방재센서 기술이 중요하며 광섬유를 이용한 센서에 대한 관심이 높아지고 있다. 본 논문은 광섬유 센서 내장 탄소섬유시트로 보강된 RC보의 계측된 데이터로 결함 탐지 연구를 수행하였다. 미분의 국부적 변동 특성을 이용한 Method Ⅰ과 컨벌루션 방법을 이용한 Method Ⅱ를 비교, 분석하였다. 다른 차원의 데이터를 비교하기 위해서 무차원화 시켰으며, 분석 결과 Mehtod Ⅱ가 결함의 위치를 예리하게 잘 탐지하는 것으로 나타났다. Method Ⅱ인 컨벌루션에 사용 되는 필터 벡터를 잘 응용하면 더 좋은 효과를 기대할 수 있을 것으로 판단된다.

Cured-in-place-pipe(CIPP) is the most adopted trenchless application for sewer rehabilitation to extend the life of the existing sewer without compromising both direct construction and indirect social costs especially applied in the congested urban area. This technology is globally and domestically known to be the most suitable for partial and full deteriorated pipe structure rehabilitation in a sewer system. The typical design of CIPP requires a significant thickness of lining to support loading causing sewage flow interruption and increasing material cost. This paper presents development of a high strength glass fiber composite lining material for the CIPP application and structural test results. The test results exhibit that the new glass fiber composite lining material has 12 times of flexural strength, 6.2 times of flexural modulus, and 0.5 Creep Retention Factor. These test results can reduce lining design thickness 35% at minimum. Even though taking into consideration extra materials such as outer and inner films for actual field applications, the structural capacity of the composite material significantly increases and it reduces 20 percent or more line thickness as compared to the conventional CIPP. We expect that the newly developed CIPP lining material lowers material costs and minimizes flow capacity reduction, and fully replaceable to the conventional CIPP lining materials.

Since electric energy is used in industry, mass production and various conveniences are provided. To provide convenience for the construction and operation of such electric energy transmission and distribution facilities, it is increasing that the demand for special purpose vehicles, that is, telescopic aerial work platform vehicles. When working active electric work using the telescopic aerial work platform vehicles, due to active electric work is inevitable, it is essential to ensure insulation performance for the safety of the operator. In this paper, we study the design and development of mechanical properties for filament winding process of glassfiber/epoxy composite, it is required to boom of telescopic aerial work platform vehicles. The glass fiber/epoxy composite filament winding process and its mechanical properties were evaluated to replace the existing ATOS80 boom. By filament winding process it was obtained the mechanical properties required for the design analysis of the glass fiber/epoxy composite boom. Using this, the insulated boom for the 30m class aerial work vehicle was designed and was manufactured by applying the filament winding process. The fabricated composite boom was evaluated by the static strength test to meet the required strength. The maximum displacement was 84mm and the crack occurred at the maximum load of 8981N. It satisfied the maximum lifting load of 4900N and 210mm the maximum displacement required for the boom.

PURPOSES: This study developed a new backfill method for mini trenching. The purpose of this study is to evaluate the performance of the new backfill method in the field. METHODS: In this study, asphalt pavement was created to verify mini trenching. Trenching test sections were then made in various trench widths in the asphalt pavement. The trench widths were 10 cm, 15 cm, 20 cm, and 25 cm. For the trenching test section, a general backfill method and new backfill method (2-layer SCB) were devised and applied. To evaluate the test section, a vehicle loading test and FWD (falling weight deflectometer) test were performed. RESULTS : In the vehicle loading test, the duct vertical strain of the general section was up to 22 times larger than that of the 2-layer SCB section. According to the results of the FWD test, the D0 deflection of the 2-layer SCB section was smaller than that of the general section. These results indicate that 2-layer SCB has a good structural performance. With the use of FWD data, BLI (base layer index) and MLI (middle layer index) were analyzed. BLI is an indirect index for evaluating base layer. The BLI of the 2-layer SCB section was smaller than that of the general section, because the bottom layer (cellular mortar) of the 2-layer SCB is superior to that of the general section. MLI, on the other hand, is an indirect index for evaluating subbase layer. As the trench width increases, MLI increases. The MLI of the 2-layer SCB section was smaller than that of the general section. These results indicate that the damage is relatively greater when the trench width increases and that the 2-layer SCB strengthens a relatively weakened subbase. CONCLUSIONS: In this study, the performance of the 2-layer SCB was analyzed. The results of the study showed that good performance was obtained when 2-layer SCB was applied to a mini trenching section.

This research proposes an optimal flushing operation technique in an effort to prevent secondary water pollutions and accidents in aged pipes, and to improve the cleaning effect of unidirectional flushing. Water flow directions were analyzed using EPANET 2.0, while flushing and air scouring experiments in forward and reverse directions were performed in the field. In 42 experiments, average residual chlorine concentration and turbidity were improved after cleaning compared to before cleaning. It was found that even when the same cleaning method was used, further improvement of cleaning effect was possible by applying air injection and reverse direction cleaning techniques. By means of one-way ANOVA(Analysis of variance), it was also possible to statistically verify the need of actively utilizing air injection and reverse direction cleaning. Based on correlation between turbidity and TSS, the total amount of suspended solids removal was estimated for 874 flushing operations and 194 air scouring operations. The result showed that air scouring used more discharge water than flushing by an average of 4.9 m3 yet with larger amounts of suspended solids removal by an average of 145.9 g. The result of analysis on turbidity values from 887 flushing operations showed low cleaning effect of unidirectional flushing for the pipes with diameters over 300 mm. In addition, the turbidity values measured during cleaning showed an increasing tendency as pipe age increased. The methodology and results of this research are expected to contribute to the efficient maintenance and improvement of water quality in water distribution networks. Follow-up research involving the measurement of water quality at regular time intervals during cleaning would allow a more accurate comparison of discharge water quality characteristics and cleaning effects between different cleaning methods. To this end, it is considered necessary to develop a standardized manual that can be used in the field and to provide relevant trainings.