This paper describes a development of design tool for knowledge based engineering(KBE) that covers structural, aerodynamic, and optical analysis of large-scale telescope structures. A module of the commercial program Adaptive Modeling Language(AML) was used to develop a knowledge-based design tool that reflects the design of parameters for rapid design change and analysis. Through this study, it is proposed a design tool with a knowledge based engineering and a function based design technique. The knowledge based engineering design is good at frequent design changes, and it is effective to extract a core design behavior from previous designs. It is concluded that the developed tool can bring fair effects in implementing a time and cost-effective design environment.

SUS hexagonal bar has been widely used to make many kinds of hexagonal bolt/nuts and fittings. Peeling machine is used to make lustrous and clean surface of SUS circular bar in order to remove rust and impurities from surface of raw SUS circular bar. Similarly, roll unit system is used to make SUS hexagonal bar from SUS circular bar with lustrous and clean surface. Roll unit system is mainly divided into two parts ; one is roll unit and the other is mold frame. The purpose of this study was to evaluate the structural stability of mold frame supporting roll unit with numerical analysis. As the numerical analysis result, higher structural stability was gradually shown in order of models 4, 2, 3 and 1. It was considered that the structural stability of this study was influenced by the decrease of mold frame size, especially height decrease.

본 논문에서는 이단계 칼만필터를 활용한 구조물의 3 자유도 동적변위 계측 시스템을 소개한다. 개발 시스템은 센서 모듈, 베이스 모듈, 컴퓨테이션 모듈로 구성되어 있다. 센서 모듈은 100Hz 샘플주파수의 고정밀 가속도를 계측하는 포스피드백 가 속도계와 10Hz의 샘플주파수의 저정밀도의 속도, 변위를 계측하는 저가의 RTK-GNSS로 구성되어 있다. 계측된 데이터는 LAN 케이블을 통하여 컴퓨테이션 모듈로 전송되고, 컴퓨테이션 모듈에서 이단계 칼만필터를 활용하여 100Hz 샘플주파수의 고정밀 변위를 실시간으로 산정한다. 개발 시스템의 변위 계측 정밀도를 검증하기 위해 미국, 캘리포니아에 위치한 San Francisco-Oaklmand Bay bridge 에서 현장 실험을 수행하였으며, 실험 결과 1.68mm RMS 오차를 보임을 확인하였다.

This study investigated a bio-tensegrity structural system that combines the characteristics of a general tensegrity structural system with a biological system. The final research objective is to accomplish a changeability for the structural system as like the movement of the natural bio-system. In the study, we present a shape finding procedure for the two stage bio-tensegrity system model inspired by the movement pattern of animal backbone. The proposed system is allowing a dynamic movement by introducing the concept of “saddle” for the variable bio-tensegrity structure. Several shape finding analysis example and results are presented and shows a efficient validation and suitability.

In this study, The recent national interest is focused on the welfare of the people, and new projects in the construction sector are being reduced, and the aging of infrastructure is not getting attention. In domestic case, most of the infrastructures were built in the 1970s to 1980s, and the road extension is also steadily increasing. Therefore, the costs to bridge maintenance from around 2010 by a similar route to that of advanced countries are also 4 times And it is time to pay attention to maintenance as well as construction. Therefore, a study was carried out on the valuation method considering bridge condition evaluation, which is a part of BIM library building and assembly program development. The proposed value evaluation method will be used as an index of the existence of bridges by comparing the cost required for maintenance and reinforcement of the target bridges and the costs required for dismantling and disposal in the bridge management system of the future program

A finite element impact simulation study was performed to assess structural performances of a guard-rail system for roadside using new steel materials (SS275) in the KS standard. The type SS275 shows an enhanced tensile strength in comparison with the former type SS400. Subsequent simulation results present that the improved model performs much better in containing and redirecting the impacting vehicle in a stable manner. The numerical results for various parameters are verified by comparing different models with dynamic responses determined in the barrier from the crash simulation.

Construction techniques and materials are developing and structures are designed to be irregular shaped, and therefore more detailed structural analysis is required. The purpose of this study is to analyze the cause of accidents related to falsework systems during construction and discuss prevention methods in order to prevent accidents relate to prefabricated shoring system during construction. In this paper structural analysis was conducted to study the influence of slab irregularity on system supports and analysis to investigate the participation of the bracing in the system support.

본 연구에서는 5층에 설치된 능동질량감쇠기를 사용하여 5층 철골구조물의 처음 세 개 모드의 모드 특성을 식별하였다. 이 건물은 병진모드와 비틀림모드의 고유진동수가 매우 근접하며, 이 경우 정확한 모드 분리와 모달 파라미터 식별은 매우 어렵다. 사인 하중 가진실험을 수행하여 모드 진동수, 감쇠비, 질량, 모드형상을 식별하였고, 근접한 모드 응답을 분리하였다. 식별된 시스템은 동일 한 입력신호를 사용하여 측정된 구조물의 응답과 매우 근접한 응답을 추정할 수 있다.

In order to improve the seismic performance of structures, friction pendulum system (FPS) is the most commonly used seismic isolation device in addition to lead rubber bearing (LRB) in high seismicity area. In a nuclear power plant (NPP) with a large self weight, it is necessary to install a large number of seismic isolation devices, and the position of the center of rigidity varies depending on the arrangement of the seismic isolation devices. Due to the increase in the eccentricity, which is the difference between the center of gravity of the nuclear structure and the center of stiffness of the seismic isolators, an excessive seismic response may occur which could not be considered at the design stage. Three different types of eccentricity models (CASE 1, CASE 2, and CASE 3) were used for seismic response evaluation of seismically isolated NPP due to the increase of eccentricity (0%, 5%, 10%, 15%). The analytical model of the seismic isolation system was compared using the equivalent linear model and the bilinear model. From the results of the seismic response of the seismically isolated NPP with increasing eccentricity, it can be observed that the effect of eccentricity on the seismic response for the equivalent linear model is larger than that for the bilinear model.

본 연구에서는 다양한 변수를 갖는 병렬 RC 구조벽체시스템에 대한 성능기반설계의 타당성과 이에 따른 모멘트 재분배 개념의 적용성을 분석하기 위해 횡력을 지지하는 병렬 RC 구조벽체시스템에 대한 비선형해석을 수행하였다. 설계변수(철근 비, 콘크리트변형률, 벽체높이)가 병렬 RC 구조벽체시스템의 거동에 미치는 영향을 분석하였으며 이를 기반으로 병렬 RC 구조벽체시스템의 성능기반 설계를 위한 고려사항을 제안하였다. 비선형해석 결과, 병렬 RC 구조벽체시스템 성능기반 설계 와 모멘트 재분배 개념의 적용을 위해서는 연결보의 항복여부에 대한 고려가 필요한 것으로 나타났다. 높은 벽체의 경우, 연 결보가 항복하지 않고 탄성 상태로 거동할 수 있기 때문에 고층 병렬 RC 구조벽체시스템에 대해 성능기반 설계 및 모멘트 재분배 개념을 적용하기 위해서는 벽체에 높은 수준의 소성변형능력을 필요로 하며, 이를 위해 벽체 압축단부에 횡보강을 필수적으로 실시해야 한다.

This paper analyzed structural behaviors of the staggered truss system, typically used in low seismicity regions, resisting the lateral loads such as wind and seismic load. A comparative study of cost and efficiency was carried out by analysing and designing the 10- and 20-story buildings with various types of truss, including pratt, howe, warren, K-, and vierendeel, which may typically be used in staggered truss system. In design, column and truss members are selected in group, and the efficiency of the member design was judged by average demand capacity ratio of the all members in same group. And economic analysis of the system was investigated by the quantity of the structural members. As a result, staggered truss system with the pratt truss and warren truss showed the most economical and efficient performance for 10-story building, and 20-story building, respectively.

This paper is a study on the nonlinear behavior of polyhedron curved space roof as building structures of quasicrystal system. The quasicrystal is made up of two kinds of parallel hexahedrons, and all the line elements of the parallelepiped have the same length. The quasicrystal design grid dome has a pentagonal symmetry and all members have the same length. This paper described form of design gird dome, and showed the analysis conditions. Also, The displacement-load curve is shown through the analysis and we grasped the flow of the load and forces through analysis of design grid dome applied quasicrystal system.

The objective of this research is to development of a parametric design system for membrane structures. The parametric design platform for the spatial structures has been designed and implemented. Rhino3D is used as a 3D graphic kernel and Grasshopper is introduced as a parametric modeling engine. Modeling components such as structural members, loading conditions, and support conditions are developed for structural modeling of the spatial structures. The interface module with commercial structural analysis programs is implemented. An iterative generation algorithm for design alternatives is a part of the design platform. This paper also proposes a design approach for the parametric design of Spoke Wheel membrane structures. A parametric modeling component is designed and implemented. SOFiSTik is examined to interact with the design platform as the structural analysis module. The application of the developed interface is to design optimally Spoke Wheel Shaped Ductile Membrane Structure using parametric design. It is possible to obtain objective shape by controlling the parameter using a parametric modeling designed for shape finding of spoke wheel shaped ductile membrane structure. Recently, looking at the present Construction Trends, It has increased the demand of the large spatial structure. But, It requires a lot of time for Modeling design and the Structural analysis. Finally an optimization process for membrane structures is proposed.