Marine casualties originated from fishing vessel occupied about 70% of the whole marine casualties in Korea from 2001 to 2010, this ratio was not much changed as it was before. Therefore a pragmatic counterplan to decrease of casualties in fishing vessel is indispensable for reduction of the nationwide marine casualties. But since the casualties occurred by fishing vessel may have a different causes and counterplan according to the operating type of it, in this paper, fishing vessels classified into 12 types by operating method and inspected the causes and counterplan for that. The operating type of fishing vessel occurred the specific casualties more were jig boat in collisions and fire explosion, trap fishing boat, mixed fishing boats and inshore gill netter in collisions, stow netter in machinery damages and capsizing, offshore gill netter in machinery damages, fish carrier in collisions. It must be emphasized that the higher ranked types of vessels, especially jig boat have to take special care to the approaching vessels under way, trap fishing boat to rear look out and mixed fishing boat must keep on safety speed and be taken an education for advance the skill of operating radar as well. For all 12 types of fishing vessel, it is necessary for an operator to make strict precaution on the other vessel under way systematically and keep the regulation for preventing collisions, and for an engineer on watch to make a check the electricity and the engines periodically for reduction the fire explosion and machinery damages.

해양안전심판원에 따르면 선박의 등록 척수는 점차 줄어드는 추세이지만, 전체 해양사고 척수와 충돌사고 척수는 증가 추세를 보이고 있다. 2008년부터 2012년까지 최근 5년간 해양사고 발생 현황을 분석해 보면, 해양사고에서 충돌사고가 37 %로 가장 높게 나타났으며, 이러한 충돌사고에서 어선이 58 %로 가장 많이 발생되었는데, 그 중에서도 20톤 미만의 소형선박의 충돌사고가 26 %로 가장 많은 것으로 확인되었다. 또한, 충돌사고의 절반이 넘는 56 %의 선박이 충돌직전까지 상대선박을 발견하지 못한 것으로 분석되었는데, 이러한 사실은 충돌사고가 대부분 경계소홀로 인하여 발생한 것임을 알 수 있다. 따라서 이러한 충돌사고를 줄이기 위해 어선의 운항특성 및 운항과 관련된 제반 규정을 검토하여 어선의 승선 인원, 교육 및 훈련, 그리고 항해장비 측면에서 개선 및 보완할 수 있는 방안을 제시하였다.

Fishing efficiency of the squid jigging vessel using the LED and metal halide fishing lamp combination was analyzed to reduce the cost for fishing operation utilizing the fishing light system for high degree of efficiency in the squid jigging fishery (one of the representative coastal and offshore fisheries in Korea). This study aims to improve the nature of existing LED lamps and to develop fan-shaped LED lights having 180W of power and ±45˚ angle of light intensity distribution. The marine experiment for making a comparison of their fishing efficiency was tested by a 9.77 tons fishing vessel from Oct. through Dec. 2012. As a result, experimental fishing vessel showed slightly higher fishing efficiency than the average of metal halide lamp-equipped vessel and 20% energy savings. This means that the combination of LED and metal halide lamps would provide an efficient way to lower energy consumption while maintaining fishing efficiency.

The analysis of the written verdicts in recent five years was conducted to obtain preventive measures of collision between fishing vessel and non fishing vessel. As a result, a collision much happened in offshore trap for fishing vessel and below 5,000 tons of small and medium class for non fishing vessel. A person involved in a marine accident occupied 68% in sixth class deck officer and small boat operator for fishing vessel and 29% in third class deck officer for non fishing vessel. 90% of the collision happened in a underway by operating state and 84% in sight of one another by visibility state. The systemic radar training was required since 47% of the collisions was occurred on the condition of radar operation in fishing vessel. The main cause of poor lookout was a intensive fishing and poor lookout on movement by radar for fishing vessel and one man watch system and no recognition of one another by radar for non fishing vessel. This result is expected to contribute for the decrease of collision.

This study is aimed to find a control factor for the marine casualty of fishing vessel by using the risk quantitative method of marine casualty, and sequentially timed event analysis for the reason finding. The result is that collision, sinking, and capsizing took high risk need to be strongly controlled. And the accident reason and control factors distinguished are as follows. The 82.2% of collided fishing vessels have negligence of look out as a immediate cause, while it was judged that underlying causes were the characteristics of vessels and fishing method, lack of suitable complement, fatigue, the prejudice or ignorance on steering and sailing rules. So the control factors are; firstly needs educational control measures and in terms of systemic control approach expand the range of the certificate of competency more smaller tonnage.

One of representative Korean fisheries, jigging and angling has 5,700 vessels for squid and hairtail. Hairtail angling is the most typical fishery in Jeju and has an enormous impact on regional economy. However, the price hike in oil and labor costs triggered the necessity of developing a high efficient and energy saving fish luring lamp in recent times. For that reason, this study aimed to analyze the fishing performance of the aircooled LED lamp targeting hairtail angling fishery. The experiment was conducted from September through October in 2009-2011 for a 9.77 ton of fishing vessel setting up 100 lamps. The fishing performance was tested compared with 6 vessels using metal halide lamps in the same waters. As the LED lamp's performance goes up, different lamps were used in 2008 for 80W, 2009 for 120W and 2011 for 180W respectively. The catch and CPUE of the experimental vessel have gradually increased respectively taking the 4th and 6th place in 2009, the 4th and 2nd place in 2010, the 1st and 1st place in 2011 among the 7 vessels. In summary, the LED fishing lamp showed higher fishing performance than comparison groups. It saved 33% of oil consumption and cut down on operating expenses and greenhouse gases emission.

This study is aimed to utilize a basic data for setting up an allowable air noise with IMO standard in accommodation and working areas of 24m longer fishing vessels. The air noise in accommodation and working areas of 300 tons class squid-jigger were evaluated and the levels were compared to the allowable levels of IMO. The results indicated that the maximum range of noise levels was estimated to be between 54.8dB (A) and 83.2dB, and the correlation between the distance from the main engine to measuring point and the maximum noise level of each point was shown to be y=-13.8log (r)+92.91 (r2=0.821). In addition, except the case of making an accommodation area near to the engine room in 24m longer jigging vessels, it was evaluated that the accommodation noise regulation of 1,600 tons international voyage vessels with 60dB (A) or an improved noise level with 65dB (A) could be properly applied.

In order to test the applicability of bunker-A in a diesel engine for small-fishing boat, the investigation of the engine performance and the exhaust emission was performed under various conditions of fuel property, intake air pressure and fuel temperature. It was also performed based on IMO NOx Technical code. At high load, the energy consumption rate of bunker-A was lower than that of diesel oil, and the characteristics of exhaust emission of bunker-A were similar to those, and NOx emission rates of both fuels satisfied the IMO NOx emission regulation limits. The energy consumption rate and characteristics of exhaust emission were improved as the intake air pressure was increased, but these were not improved remarkably as the temperature of bunker-A was heated. However, at low load the energy consumption rate, CO emission rate and HC emission rate of bunker-A were higher than those of diesel oil, but NOx emission rates of the fuels were about the same. In addition, at low load the energy consumption rate and CO emission rate of bunker-A were increased as the intake air pressure and the temperature were higher than normal conditions. Accordingly, it is thought that the use of bunker-A in a kind of test engine is possible at high load. On the other hand, it is thought that more research is needed to improve the combustion efficiency under low temperature and low load condition.

This study intends to present a direction for the better reforming of fishers'onboard living conditions and proposals for preparing for ratification of the Work in Fishing Convention by means of making a comparison between standards on recent national fishing vessel accommodation facilities and standards on the Work in Fishing Convention and Its Recommendation, 2007, ILO. For the most part of standards on national fishing vessel accommodation facilities are somewhat insufficient to satisfy the provisions in Annex III of the Convention. Considering by items on fishing vessel accommodation facilities, the standards on insect protector, noise and vibration, heating and air conditioning, lighting, persons per sleeping room, recreational facility are not provided in national law. Headroom, separation of accommodation, sleeping room floor area, mattress size, mess room, galley and food storage are partially sufficient for the Convention. In case of sanitary facilities, national standards are not sufficient for the Convention. The other side, facilities related safety of ship and crew such as emergency escape etc., are fully sufficient for the Convention. These insufficiencies caused by different types of fishing vessel depend on originality of fishing method and practices. In the comparison between equivalent tonnage about vessel's length on convention and calculated tonnage of national existing fishing vessel, the difference are 226tons about length 24m and 501tons about length 45m. For that reason, headroom, persons per sleeping room, cabin of sicker and injured, sanitary facilities may decide to use gross tonnage in place of length (L) and the alleviating measure basis of convention. But in case of standards on sanitary facilities which are unsufficient for the Convention, specially in coastal fishing vessel length basis should be adopted with alleviating basis for less than length 24m.

The ship's heading information of hybrid GPS/EM compass were applied to the AIS of fishing vessel and examined the possibility of accuracy improvement. It is observed 453 each in AIS receiver of land among 3,982 each in AIS Rx/Tx transponder of the test ship at sea, and transmission interval according to the speed of ship is determined the 11.4% good transmitting data of the all information. In results, maximum compass error for the ship's heading of an EM compass was 19.1˚. The variance of ship's heading owing to the speed of ship is surveyed. The COG (Course Over Ground) was changed extremely in 180˚W-179˚E range under 4.9knots, and in 24˚W-23˚E range over 4.9knots. Finally, using the ship's heading of EM compass and the COG from GPS for the autopilot system of a small fishing boat and the ship's heading information of AIS results in danger on the own ship's navigation safety and leads to make confusion both the others and VTS (Vessel Traffic Service) center. Therefore, the hybrid GPS/EM compass is identified as the best system for a small fishing boat and is allowed to offer continuously a ship's heading information with high accuracy and stability.

This paper describes on the real-time monitoring of net setting and hauling process for fishing operations of Danish seine vessels in the southern waters of Korea as an application of a PC based ECDIS system. Tracking of fishing process was performed for the large scale Danish seine vessel of G/T 90 and 350 PS class using the fishing gear which the length of net, ground rope, head rope and sweep line including warp in both sides were 86m, 104m, 118m and 3,200m, respectively. Tracking information for net setting and hauling process was continuously recorded for 23 fishing operations performed on November and December, 2003. All measurement data, such as trawl position, heading, towing course and past track which was individually time stamped during data acquisition, was processed in real time on the ECDIS and displayed simultaneously on the ENC chart. The results indicated that after the separation of a marker buoy from Danish seiner, the averaged running speed of vessel and the averaged setting period while shooting the seine on the course of diamond shape to surround the fish school in the 23 fishing operations were 8.3 knots and 13.1 minutes, respectively. And with the maker buoy taken on board, the averaged running speed of vessel and the averaged towing period while closing the seine on the straight route was 1.0 knots and 47.0 minutes, respectively. After the closing stage of hand rope, the hand rope was towed by the averaged speed of 2.2 knots during the 13.0 minutes. The average area for route of diamond shape swept by sweep lines of the seine in 23 fishing grounds was 709,951.6m2. Further investigation is also planed to provide more quantitative tracking information and to achieve more effective surveillance and control of Danish seine vessels in EEZ fishing grounds.

The transmittance properties of fishing lamp of the squid jigging vessel was investigated during nighttime operations in the Northwest Pacific on 21 and 29 September 2005. The metal halide lamps of white color(2.0kW×168) in the air and metal halide lamp of white color(10.0kW×1) in the underwater were used as a fishing lamp for gathering squids. The relative irradiance of metal halide lamp in the air showed peak in 850nm of wave length. The relationship between underwater illuminance(Y) and water depth(X) of metal halide lamp light in the observation areas is represented, Y=84.137e-0.1105X, R2=0.9974. The distribution of underwater illuminance of measure points St. 1-5 showed low value of 0.11x in 80m depth.

In spite of many efforts, in the design of high speed fishing vessel the sea-keeping performance improvement without neglection of resistance-propulsion performance by hull form itself has its limitations. In this paper, the development of sea-keeping improving appendage pitching and trim improver for high speed planing hull on behalf of the hull form of fishing vessel has been introduced. The developed appendage verified its effectiveness in the full scale test and also has been proved the better resistance performance in the model test and full scale test.

본 연구에서는 10톤급(9.77 G/T) 소형 연안어선의 저항성능을 회류수조를 이용한 모형시험을 통하여 조사하고, 저항성능개선을 위한 선형특성과 초기 트림에 대한 영향을 검토하였다. 본 연구를 통하여 다음과 같은 몇가지 결론을 도출할 수 있다. (1) 선미 A.P. 이후 돌출부 길이를 키우는 것은, 트림이 억제되면서 선수부 쇄파 현상이 커질 수 있으나, 선미단에서 빠져나가는 유체의 흐름을 개선시켜 저항성능을 크게 향상시킬 수 있다. (2) 적절한 초기 트림을 줌으로써 저항성능이 크게 개선될 수 있다. (3) 선수부 유체흐름을 개선시키기 위해 챠인의 폭을 줄인 선형보다는 이 폭을 그대로 유지하는 것이 파가 선체의 선측을 타고 올라가는 것을 방지하고 트림을 키워 성능측면에서 유리하게 작용한다.

After studying the composition about the torsional shafting of main engine for fishing vessel with Power Take Off (PTO) System, the authors made a computer program using the transfer stiffness coefficient method (TSCM) for analyzing torsional vibration about the shafting with PTO system and nonlinear elastic coupling. The torsional shafting of main engine was separated by 3 types according to the connecting. The torsional shafting of main engine was separated by 3 types according to the connecting condition of main engine with propeller or the PTO system or both of them. In this paper, the change of natural frequencies and natural modes according to connecting condition of torsional shafting and nonlinear elastic coupling were analyzed. The accuracy of the TSCM was confirmed by comparing with the computational results of the Finite Element Method.

꽁치봉수망 조업시 어선의 집어등에 의한 수중환경의 변화를 밝혀 광 환경이 꽁치의 어획에 미치는 영향을 분석하기 위한 기초 단계로 수중 조도를 측정하여 꽁치가 분포하는 어획 수층의 광 환경을 분석한 결과를 요약하면 다음과 같다. 공기중에서 홍색 백열등과 할로겐등의 방사조도는 둘 다 1,052nm의 파장에서 최대치를 보인 후 감소하는 경향을 나타내었고, 600nm이하의 파장에서는 할로겐등이 홍색 백열등에 비해 방사조도가 약간 높게 나타났다. 공기중 조도는 좌현 선미에서 가장 높았고 선수에서 가장 낮게 나타났다. 조사해역에서의 집어등 불빛의 수중투과 특성은 50m 수층에서 각각 0.31x, 0.61x 이하로 나타났으며 일반적인 꽁치어장의 특성을 가진 어장에서 볼 때 , 꽁치가 집어되는 수층의 조도는 0.51x 이상인 것으로 보인다.

TPI는 고속 활주선의 소음, 진동, 트림 및 핏칭운동을 감소시킨 것으로 실선 시운전에서 증명되었다. 또한 모형시험에서 저항성능도 미소하게나마 개선시킨 것으로 입증되었다

한국 연근해에서 조업하고 있는 어선을 효율적으로 관리할 수 있는 어선관제시스템의 구축을 위한 기초 연구로서 제주도 성산포항을 거점으로 하여 조업중인 대형선망어선단의 어로과정의 ARPA 영상을 디지털신호로 변환시켜 분석하고 VTMS를 이용하여 모의실험을 행한 결과를 요약하면 다음과 같다. (1) 대형선망어선단의 어로과정을 분석한 결과 투망소요시간은 16분, 양망소요시간은 35분이었고, 앞잡이 배가 끌어 주는 로프의 길이는 200m, 투망시 선회경은 340.8m, 선회속도는 약 6kts로써 조업 과정을 명확하게 파악할 수 있었다. (2) 실선실험에서 구한 투.양망과정에 유향.유속을 NE, 2kts와 SW, 2kts로 가상하여 시뮬레이션한 결과, 각각 SW, NE 방향으로 편위됨을 알 수가 있었다. 이와 같이 어장환경정보 또는 어업 정보나 조선정보를 관제시스템에 가미함으로써 실제조업과 같은 상황을 예측할 수 있었으며, 클로즈업시킨 화면을 통해 투 양망중 예상되는 상황과 문제점을 검토할 수 있었다. (3) 시뮬레이션에서 사용한 VTMS의 레이더 관제범위는 16mile이었고, 관제범위를 넘었더라도 타관제선으로의 이관이 가능하였다. 또한, 관제선과 집단선단들과의 거리와 방위를 측정하고 분석하면 관제선의 위치선정이 용이함을 알 수 있었다. (4) 조업선들이 어황정보와 안전항행정보를 제공받아 안전하고 효율적인 조업을 행할 수 있는 어선관제 시스템(FVTMS)의 예측모델을 제시하였다. 이와 같이 VTMS용 관제시스템을 이용하여 선단조업어선의 어로과정에 대한 시뮬레이션 한 결과, 근접조업에 따른 잦은 경보와 추적 상실 등 몇가지 기능상의 문제점이 발견되었으므로 어선관제시스템(FVTMS)에 적합한 프로그램이 시급히 개발되어야 할 것으로 사료된다.

연안 소형 어선의 조업 효율을 향상시키기 위한 연구의 일환으로 소형 유압식 어로윈치시스템을 설계하고, auto tension 기능을 내장시켜 이 시스템의 개루프 상태에 대한 동적 응답 특성을 분석, 고찰한 결과를 요약하면 다음과 같다. 1. 본 연구에서 설계, 제작한 소형 윈치시스템은 갑판상 어느 장소에서도 조작이 가능하도록 원격조작방식을 채용하고 있기 때문에 어로 작업시의 인력 감소와 작업의 효율성을 높일수 있다고 생각된다. 2. 솔레노이드 밸브를 ou/off 조작하여 윈치를 구동할 때, 정전 및 역전 구동 조작에 대한 윈치 드럼의 회전 지연시간(dead time)은 각각 0.09 sec, 0.04 sec이었다. 또한 on/off 레버의 조작을 행한 직후 응답 특성은 약간 불안정하였지만, 짧은 경과 시간을 거쳐 안정되는 추종성능을 나타내었다. 3. 윈치를 auto tension mode로서 구동하는 경우, 윈치의 회전축에 55.9 kgf.m 이상의 토오크가 작용하면 윈치는 5.1 rpm의 회전속도로서 줄을 풀어내고, 그 이하의 토오크가 작용하면 11.1 rpm의 회전속도로서 줄을 감아들이는 자동 권양 윈치의 기능을 발휘한다. 4. 윈치의 auto tension mode에 대한 과도 응답에서 부하가 급격히 증가할 때와 감소할 때의 정정 시간은 0.12 sec, 0.2sec이었고, 그 때의 회전속도는 각각 11 rpm, 5.3 rpm이었다. 5. 원격제어조작에 따른 윈치의 토오크 및 회전속도에 대한 추종성능은 정전 구동에 있어서는 0.23 sec, 역전 구동의 경우에 있어서는 0.37 sec 이내로서 비교적 안정된 응답 특성을 나타내었다. 이상의 결과로부터 본 연구에서 설계한 소형 어선용 자동 권양 윈치 시스템은 인력을 절감하고, 부하의 급속한 변화에 대한 추종 성능이 현용 어로시스템에 비하여 매우 우수하기 때문에 해상에서 어로작업시 과부하에 대한 어구의 손상 방지 및 조업 효율의 향상에 크게 기여할 것으로 판단된다.