Waste electrical and electronic equipment (WEEE) has been received much attention recently due to rapid changes in materials and shorter replacement of consumer products. Most of WEEEs are collected and recycled at the designated recycling centers in Korea, and final residues after recycling, sorting and shredding them to separate valuable and recyclable parts in series are left as forms of shredded plastic mixtures, which would be a problem to be resolved. By further plastics separation the polyurethane foams are mostly remained and becomes waste to be treated by appropriate methods. Gasification to produce syngas and incineration to recover energy for such polyurethane foam waste could be utilized instead landfill presently treated. In this study the experiment was conducted to evaluate such performance characteristics of thermal processes. Pelletized solid refuse fuel (SRF) was fabricated to feed into the test furnace even though it was light with low density. Thermogravimetric analysis, proximate analysis and higher heating value were made. During gasification and incineration, gas composition with gaseous pollutants were measured. Due to nitrogen content in polyurethane, nitrogen containing gaseous substances such as NH3 and HCN were observed with varying equivalent air ratios (ERs). The assessment of polyurethane waste foam to energy using incineration and gasification was made with finding out the optimal condition of air injection to emit less pollutants in both operations. Produced syngas could be utilized as energy fuels by lowering pollutants emission.

It is known that mackerel and pork belly release a strong odor in the process of roasting. We evaluated a dilution factor of odor arising during roasting mackerel or pork belly and the relative odor strength using several cooking tools and analyzed compounds causing odors with gas chromatograph / mass detector. Roasting pans used were grill with lid, electric grill without lid and general roasting pan, and a grill with lid can attach the activated carbon charcoal deodorant at the inside of lid. And all electric grills have a drip tray under the heater. We investigated characteristics of odor emission depending on the presence of water and deodorants in these cooking tools. Study has shown that roasting mackerel produces approximately 36 time more odors than roasting pork belly, and the reduced odor emission when roast with water. And it shows the reduced deodorant effect when cooked with water after attaching activated carbon charcoal in the cooking pan. Major odor causing compounds arising when cooking mackerel and pork belly were aldehydes with high boiling point such as octyl aldehyde with a low odor threshold value.

In this study those currently operating pyrolysis oil plant were selected for the investigation. The yield of the oil andfuel was assessed for its use as fuel and the char component analysis, and the reaction time to collect contaminantscollected and analyzed. As the result, about 40% of the oil was yielded and oil could be used as an alternative fuel. Char’sleaching test analysis result was satisfied with the landfill standard. And emission of Dioxin and pollutants was analyzed.The highest concentration of dioxin was 0.7347ng I-TEQ/Sm3. The result satisfied the requirement however the emissionconcentration was changed depending on the input Fuel. Therefore the appropriate pollution control facility should berequired.

This paper addresses the fugitive emission factors of showcase at use-phase and disposal-phase. The residual quantities of Korean-made fifty- two waste showcase were weighed, using a commercial recover of refrigerants to determine the emission factors at the disposal-phase. On the other hand, the emission factors at use-phase were estimated from the residual quantities and operating times. The average residual rate of fifty two scarp showcase is determined to be 75.6 ± 5.3%. The emission factor at the use-phase is estimated to be 2.8 ± 0.7%/yr in the case of using average age of 11.1 years and the average residual rate determined here. The emission factor at the disposal-phase, refrigerant is accomplished has not recycled, the residual rate was assumed that the emission factor. We estimate 7.8 g/yr for the average emission quantity of refrigerant per operating showcase, while 234.4 g for that per waste showcase. Since the chemical compositions of refrigerant of waste showcase were the same as those of new refrigerant, it is expected that the refrigerant recovered from waste showcase can be reused for refrigerant.

Although scrap domestic refrigerator is regarded as a major source of HFC-134a, little information is available for its emission characteristics of HFC-134a. This paper addresses the fugitive emission factors of domestic refrigerator at usephase and disposal-phase. The residual quantities of Korean-made forty three scrap domestic refrigerators were weighed using a commercial recover of refrigerants to determine the emission factors at the disposal-phase. On the other hand, the emission factors at use-phase were estimated from the residual quantities and operating times. The average residual rate of forty three scarp domestic refrigerators is determined to be 75.1 ± 5.2%. The emission factor at the use-phase is estimated to be 2.4 ± 0.5%/yr as a result of using average age of 12.3 years and the average residual rate determined here. The emission factor at the disposal-phase is determined to be 31.9% after adopting 38% of the recycling rate of refrigerant reported by Recycling Center. We estimate 2.9 g/yr for the average emission quantity of HFC-134a per operating refrigerator, while 33.5 g for that per scrap domestic refrigerator. Since the chemical compositions of refrigerant of scrap domestic refrigerator were the same as those of new refrigerant, it is expected that the HFC-134a recovered from scrap domestic refrigerator can be reused for refrigerant.

Odor from sewage treatment plants have the potential to cause significant annoyance and to impact the amenity. In this study, odor emission characteristics at unit process of 48 sewage treatment facilities in 39 plants were evaluated using composite odor concentration and hydrogen sulfide (H2S) concentration. The values of composite odor concentration (geometry mean) and H2S concentration (median) for sludge treatment processes are higher than those for the other treatment processes. The composite odor concentration and H2S concentration are distributed over a wide area in each process. Composite odor concentration (dilution ratio) was found to have the significant correlation with H2S concentration (p=0.000<0.05). The H2S concentration accounted for 67.1% of composite odor concentration.

Quantifying greenhouse gas (GHG) emission is important for evaluating various reduction measures for greenhouse gas, which causes significant negative impacts on earth. To estimate GHG emission from waste sector over the period of between 2000 and 2009 in Daejeon Metropolitan City, the 2006 IPCC (Intergovernmental Panel on Climate Change) and Korean GHG Inventory for local government guidelines and methodologies were employed. Four different waste treatment methods (landfill, incineration, biological treatment, and Sewage wastewater treatment) were evaluated to estimate GHG emission by following the guidelines. The trends of GHG emission rate by direct emission increased between 2000 and 2009 as a result of increased incineration rate. The solid waste sector was directly responsible for 307,700 tonCO2eq/yr in 2009. Incineration contributed approximately 57% of the GHG emission, while landfill disposal was responsible for about 30% of the GHG. Approximately 464,400 tonCO2eq/yr in 2009 was emitted by indirect emission from the waste sector. Based on the results, a variety of measures are needed to reduce the GHG emission from waste sector in Daejeon Metropolitan City along with implementing effective waste source reduction and recycling policy. More specifically, this evaluation proposed that among the possible reduction options, further source separation of recyclables as well as improved diversion of recyclable materials at proposed Daejeon resource recycling complex in 2014 would have the greater benefits for reducing GHG emissions in Daejeon Metropolitan City's waste sector.

The study is about variations in Carbonyl compounds concentration within apartment buildings according to pre-residence and residence. We consecutively investigated indoor air pollutants in 120 households in 6 cities at pre-residence and residence. Carbonyl compounds were collected using the 2,4-DNPH cartridge and were analyzed using HPLC. The carbonyls concentration of indoor air in the new apartments before occupation measured formadlehyde(76.0㎍/㎥), acetone(85.9㎛/㎥), acetaldehyde(13.8㎍/㎥). The carbonyls concentration of indoor air in the new apartments after occupation measured formadlehyde(233.1㎍/㎥), acetone(128.9㎍/㎥), acetaldehyde(29.8㎍/㎥), respectively. As a result, the mean concentration of carbonyl compounds within the pre-occupancy stage was lower than those of residence.

This study was designed to evaluate qualitatively and quantitatively the pollutant compositions, which were emitted from three types of mosquito repellents(MRs)(mat-, liquid-vaporized, and coil-type) by utilizing a 50-L environmental chamber. A qualitative analysis revealed that 42 compounds were detected on the gas chromatography/ mass spectrometer system, and that the detection frequency depended upon chemical types. Nine of the 42 compounds exhibited a detection frequency of 100%. Four aromatic compounds(benzene, ethyl benzene, toluene, and xylene) were detected in all test MRs. The concentration equilibriums in the environmental chamber were achieved within 180 min after sample introduction. The coil-type MR represented higher chamber concentrations as compared with the mat- or liquid-vaporized-type MR, with respect to the target compounds except for naphthalene. In particular, the chamber concentrations of ethyl benzene, associated with the use of coil-type MR, were between 0.9 and 65 mg m-3, whereas those of mat- and liquid-vaporized-type MRs were between 0.5 and 2.0 mg m-3and 0.3 and 1.4 mg m-3, respectively. However, naphthalene concentrations in the chamber, where a liquid-vaporized-type MR was placed, were measured as between 17.8 and 56.3 mg m-3, but not detected in the chamber, where a mat- or coil-type MR was placed. The empirical model fitted well with the time-series concentrations in the environmental chamber(in most cases, determination coefficient, R2 ≳ 0.9), thereby suggesting that the model was suitable for testing emissions. In regards to the target compounds except for benzene, although they were emitted from the MRs, health risk from individual exposure to them were estimated not to be significant when comparing exposure levels with no observed adverse exposure levels or lowest observed adverse exposure levels of corresponding compounds. However, it was concluded that the use of MRs could be an important indoor source as regards benzene.

Emission characteristics of volatile organic compounds (VOCs) were investigated in the flue gas emitted from wood drying process for plywood manufacturing. The moisture content of raw timber was average 48%, and its density was 831.55 kg/m3. But the moisture content of dried wood is needed less than around 10%, thus the moisture contents of flue gas should be remarkably high(about 18.2 V/V%). Therefore, the vapor in flue gas is equivalent to 320 ton-vapor/day when 1100 ton-wood/day is treated in the wood drying process. The temperature of flue gas ranges from 140℃ to 150℃ in each dryer stack with exception of the input site of wood(about 110℃). The velocity of flue gas in each stack ranges from 1.7 to 9.7 m/sec. In order to assess the concentrations and attribution rate of odorous compounds, it was analyzed about 40 VOCs in the flue gases. It was found that the major odorous compounds were 8 compounds, and the concentrations of major VOCs(ppm) were as follows; benzene: 0.054～0.052, toluene: 1.011～2.547, ethylbenzene: 0.472～2.023, m,p-xylene: 0.504～3.245, styrene: 0.015～0.148, o-xylene : 0.271～1.097, ethanol: 11.2～32.5, α-pinene: 0.908～10.578, β-pinene: 0.982～14.278. The attribution rate of terpenes (α-pinene, β-pinene) was about 60.56%, and that of aromatics and alcohols was about 22.77%, and 16.67%, respectively. It is suggested that the adequate control device should be used to control both the water soluble and non-soluble compounds because both compounds were mixed in flue gas.

It will be necessary to make proper management plans to preserve the air quality in good level for the public. In order to make these plans, source information and detail emission inventories of the city and near industrial areas should be given. However, lack of the source measurements data makes us more difficult to complete the source inventory. VOC source inventory could be utilized for the feasibility study to estimate the contribution of VOC sources presenting to the receptor such as residential area. It may give policy maker an idea how to control the air quality, and improve their social environment in the area. This study shows data that measured VOCs concentrations from the local industrial areas in Jeonju during from May 2005 to January 2006. The samples were collected from the near sources in 7 major factories in the industrial park as well as 5 general sources in near city Jeonju area to elucidate the abundances of speciated VOCs and their spacial and temporal distributions depending on source bases. Industrial sources are as follows; chemical, food, paper, wood, metal, non-metal (glass), and painting (coating) industries. The 5 general sources are sampled from tunnel, gasoline gas station, dry cleaning shop, printing (copy) shop, and road pavement working place in urban area. To understand the near source effect at receptor, samples from the 2 receptor sites (one is at center of the industrial complex and the other site is at distance residential area downwind from the center) were collected and analyzed for the comparison to source concentration. The mass contributions of the speciated VOC to total mass of VOCs measured from the different sources and ambient (2 receptors) were presented and discussed.

Nitrous oxide (N2O) is an important trace gas in the atmosphere not only because of its large global warming potential (GWP) but also because of the role in the ozone depletion in the stratosphere. It has been known that soil is the largest natural source of N2O in global emission. However, anthropogenic sources contributing from industrial section is likely to increase with rising the energy consumption, and transportation as well. In this study, a total of 32 gasoline-powered passenger vehicles (ranging from small to large engine's displacement and also ranging from aged catalyst to new catalyst) were tested on the chassis dynamometer system in order to elucidate the characteristics of N2O emission from automobiles under different driving modes. Ten different driving modes developed by NIER were adapted for the test. The results show that the N2O emission decreases logarithmically with increase of vehicle speed over the all test vehicles (N2O emission = -0.062 Ln (vehicle speed) + 0.289, r2=0.97). It revealed that the larger engine's displacement, the more N2O emission were recorded. The correlation between N2O emission and catalyst aging was examined. It found that the vehicles with aged catalyst (odometer record more than 8,0000km) emit more N2O than those with new catalyst. Average N2O emission was 0.086±0.095 N2O-g/km (number of samples=210) for the all test vehicles over the test driving modes.

In order to investigate the compositions and the emission rates of monoterpenes emitted from coniferous trees, those from Larix leptoleis (Sieb. et Zucc.) Gordon were measured. In spring and summer, the major monoterpenes were α-terpinene, α-pinene, myrcene; however, α-pinene and α-terpinene were most abundant in fall. The total mean monoterpene emission rates were 0.455 (㎍C/gdw/hr) during the whole period. The higher monoterpene emission rates were found in fall compared to those in spring and summer. In addition, the slopes (β value) between emission rate and temperature were two times lower in fall than those in spring and summer. It was also found that Larix leptoleis (Sieb. et Zucc.) Gordon had lower monoterpene emission rates than P. densiflora and P. rigida.

This study identified concentrations of air pollutants emitted from idling of vehicles such as cars, taxis, trucks, and buses. In this investigation we analyzed concentrations of SO2, NOx, CO, and CO2 emitted from exhaust pipe of vehicles as a function of vehicle type, mileage, exhaust volume, and fuel type using the GreenLine. Compact or light cars, which have relatively low exhaust volume, showed much higher exhaust concentrations of SO2, CO, and NOx than those emitted from vehicles with high exhaust volume. Vehicles using light oil showed much higher exhaust NOx concentrations than those of vehicles using gasoline. Vehicles using LPG and compact cars showed very high exhaust CO concentration compared to other vehicles. NOx exhaust concentrations were increased with increasing the mileage of vehicles.