PURPOSES :The purpose of this study was to determine the optimum mix design of the content of 100 % reclaimed asphalt pavement (RAP) for spray injection application with different binder types.METHODS:Literature review revealed that spray injection method is the one of the efficient and economical methods for repairing a small defective area on an asphalt pavement. The Rapid-Setting Polymer modified asphalt mixtures using two types of rapid setting polymers-asphalt emulsion and a quick setting polymer asphalt emulsion-were subjected to the following tests to determine optimum mix designs and for performance comparison: 1) Marshall stability test, 2) Retained stability test, 3) Wet track abrasion test, and 4) Dynamic stability test.RESULTS AND CONCLUSIONS :Type A, B, and C emulsions were tested with different mix designs using RAP aggregates, to compare the performances and determine the optimum mix design. Performance of mixtures with Type A emulsion exceeded that of mixtures with Type B and C emulsion in all aspects. In particular, Type A binder demonstrated the highest performance for WTAT at low temperature. It demonstrated the practicality of using Type A mixture during the cold season. Furthers studies are to be performed to verify the optimum mix design for machine application. Differences in optimum mix designs for machine application and lab application will be corrected through field tests.

Butanol has an ability to improve the ignition quality due to its lower latent heat of vaporization; it has an advantage to reduce a volume of a fuel tank because its energy density is higher than that of ethanol. Also, butanol-diesel oil blending quality is good because butanol has an effect to prevent the phase-separation between two fuels. Even if the blended oil contains water, it can reduce the corrosion of the fuel line. Thus, it is possible to use butanol-diesel oil blended fuel in diesel engine without modification, and it may reduce the environment pollution due to NOx and particulate and the consumption of diesel oil. Therefore, some studies are being advanced whether butanol is adequate as an alternative fuel for diesel engines, and the results of the combustion and exhaust gas emission characteristics are being presented. Though the injection and spray characteristics of butanol are more important in diesel combustion, the has not yet dealt with the matter. In this study, the influence in which differences of physical properties between butanol and diesel oil may affect the injection and spray characteristics such as injection rate, penetration, spray cone angle, spray velocity and process of spray development were examined by using CRDI system, injection rate measuring device and spray visualization system. The results exhibited that the injection and macroscopic spray characteristics of two fuels were nearly the same.

분리막 오염을 감소시키고 투과유속 향상을 위하여 관형분리막 모듈 내에 공기 분사노즐관을 삽입시켰다. 분리막 의 평균 기공크기는 0.1 μm이며 이스트를 오염물질로 사용하였다. 모든 투과실험은 노즐관을 모듈에 장착하고 공기를 주입 하지 않는 실험을 먼저 실시하고 연속해서 공기를 주입하는 투과실험을 하였다. 그 다음 노즐관을 제거한 후 공기를 주입시 키지 않으면서 투과유속을 측정하였다. 측정된 투과유속은 공기주입 효과를 분석하기 위하여 비교하였다. 공기주입에 대한 투과유속은 거의 일정하거나 증가하였다. 노즐관이 장착되고 공기 주입을 하지 않을 경우의 투과유속이 빈 관형 모듈의 경우 보다 높았다. 운전압력을 0.4 bar까지 감소시키면 노즐관이 장착되지 않는 경우와 비교하여 공기를 주입할 경우 투과유속이 21%까지 향상되었다. 기체량이 증가하여 기/액체 2상 흐름이 stratified-smooth에서 intermittent 상태로 변화됨에 따라서 공기 주입에 의한 투과유속은 30% 이상으로 증가하였다

The purpose of this study was to explore olfactory sensitivity of odors from injection molding processing. To do this, the experiment was carried out in an injection molding factory, and participants were exposed to the environment where odor-substances (Formaldehyde, Benzene, Toluene, Ethylbenzene, Xylene, Styrene) exist. In addition, we used the subjective scale using semantic adjectives as an olfactory sensitivity. As a result, the assessment structure of olfactory sensitivity was composed of eight factors (irritant, thermal, tense, unique, like-dislike, active, stable, masculine), and the main factor which was irritant characteristics explained 20% of the total olfactory sensibility. These results suggested that odors from injection molding processing would cause more negative emotional responses than the flavor which is mainly used in olfactory sensitivity. This study, as a basic study of the improvement in a factory environment for the efficiency of work, has limits in that it was conducted to the extent of identifying the olfactory sensitivity structure of those who were at a laboratory and who were exposed to the environment of odor substance induced in the injection molding processing. Therefore, for the method of removing malodorous substance, the effect of materials which can neutralize it, and the comparison of a direct performance in the environment where negative sensitivity structure exists, a series of studies which aim to improve the environment of injection molding factories, such as performance assessment in the environment of a factory and an office need to be conducted. It is expected that when these studies are put together, the improvement guidelines will be provided as a type that can maximize the effectiveness of work in the factory environment where injection molding processing is done.

An injection unit is the important part which guide the melted resine into the mold. Once injection molding is performed, there will be a pressure of 33 MPa built up inside of injection cylinder body. It was confirmed that the crack occurs by internal stress on the 9 mm material when the machine is used for long time. Because the cylinder rod has material thickness of 9~12 mm during manufacturing process on the cylinder body, there would be 3 mm thickness differences. In this experiment, IDEAS, a computer aided structure analysis software, is used to present the optimized design condition. Insert rod with inner diameter of 9 mm was set as a normal and vary 3 mm in x, y axis direction. When the internal pressure of 33 MPa occurs at the injection unit, fix the x and y direction and find out the stress acting only in z axis. It was confirmed that the stress of 45~82 N/mm 2 was built up when the left of cylinder body had been set 9 mm by using a structure analysis. Also, it has been verified the thickness of the material on the left need to be greater and equal than 12 mm to prevent a material crack by an internal stress.

MEN1 환자에서 췌장 NET는 30-80% 동반된다. 증상 및 악성 가능성이 있는 경우 수술적 절제가 예후에 중요한 영향을 미친다. 수술이 불가능한 췌장 NET에 대해 EUS-EI를 고 려할 때는 합병증과 불완전 치료 및 재발 가능성에 대한 주 의 깊은 고려가 필요하다.

목 적 : 본 연구는 수술 전 양성 및 악성 간 병변 환자에 대하여 자유호흡기법(free breathing technique)을 사용하여 b-value (50, 500, 800, 1000)를 변환시켜 조영제 주입 전·후 현성확산계수가 어떤 수치적인 변화를 나타내는지 연구하고 악성 종양의 평가 자료로 유용한지 알아보고자 하였다. 대상 및 방법 : 본 연구는 후향적 연구로써 임상윤리위원회(institutional review board, IRB)의 승인(PNUHIRB-17)을 얻어 진행하였으며 연구 기간은 2015년 11월 01일부터 2016년 01월 30일까지 부산 소재 일개 P대학교 병원을 내원하여 수술전 간 MRI 검사를 의뢰 받은 환자 38명을 대상으로 하였다. 연구에 사용된 프로토콜(protocol)은 본원에서 시행되고 있는 간 검사에 최적화된 검사기법(TR:5100 ms, TE: 79 ms, SPAIR, NEX: 6, b-value type: 50, 500, 800, 1000)으로 조영제 주입 전 축삭면 확산강조영상을 자유호흡기법으로 영상을 획득하고 PRIMOVIST 10 ml (Gd-EOB-DTPA) 주입후 20분 지연기(hepatobilliary phase)에 동일하게 반복 시행하였다. 사용된 확산강조영상은 SE single-shot EPI (echo planar imaging)을 이용하여 b-value값을 50, 500, 800, 1000 s/mm2으로 세분화하여 검사를 하였다. 정량적 평가시 Image J와 work station을 사용하여 평가 하였으며 세분화 되어있는 b-value 값에 따라 ADC map을 나타내고, 이에 대하여 병변에 관심영역을 설정하여 현성확산계수를 구하였다. 통계적 분석은 대응표본 t-Test를 사용하였으며, p < 0.05 일때 통계적으로 유의하게 평가되었다. 결 과 : 간세포암의 경우 조영제 주입 전과 후의 현성확산계수의 수치는 pre ADC (500, 800, 1000: 1.238, 1.040, 1.007 × 10-3 s/mm2), post ADC (500, 800, 1000: 1.225, 1.094, 1.002 × 10-3 s/mm2)를 나타내었다(p>0.05). 간전이암의 경우 pre ADC (500, 800, 1000: 1.450, 1.472, 1.332 × 10-3 s/mm2), post ADC (500, 800, 1000: 1.438, 1.441, 1.354 × 10-3 s/mm2)를 나타냈고(p > 0.05), 혈관종의 경우 pre ADC (500, 800, 1000: 1.591, 1.365, 1.217 × 10-3 s/mm2)와 post ADC (500, 800, 1000: 1.906, 1.614, 1.396 × 10-3 s/mm2)는 변화 있는 결과를 나타내었다(p>0.05). 결 론 : 결론적으로 양성 종양의 경우 조영제 주입 전과 후의 결과의 연관성이 크지 않았고, 규칙성이 없었다. 하지만 간세포암의 악성병변(LR-5)의 경우 조영제 주입 후가 양성 병변에 비해 통계적으로 의미 있게 낮은 현성계수의 값을 보였으며, 정성적 분석에 향상을 가져왔다. 본 연구에서 제시한 바와 같이 복부 확산강조영상의 경우 질병과 검사 순서에 따라 현성확산계수의 결과 값과 확산강조영상의 명확도가 다르게 측정 될 수 있으므로 조영 전과 후의 확산강조영상을 병행한다면 좋을 것이라고 사료되며, 조영후의 현성확산계수와 이용 가능한 검사 시퀀스를 병행한다면 양성 및 악성 질환 감별의 진단에 효율성을 가져올 것이라고 판단되었다

디젤엔진에서는 2차 분사 시스템은 다양한 배기 시스템에 적용이 가능하고, 엔진 제어와 관계없이 독립적으로 제어가 가능하기 때문에 환원제 희석 면에서도 후분사 또는 다른 농후한 환원제 분위기 형성 방법 등에 비해 장점이 많다. 2차 분사 시스템에서는 환원제의 공급 방법에 따라서 촉매의 효율은 달라질 수밖에 없다. 환원제는 일정압력 이상으로 유지 및 최적화가 필요하고, 인젝터의 위치 및 각도의 선정은 매우 중요한 인자이다. 본 논문에서는 2차 분사 조건을 변화시켜 환원제의 농도와 양을 변화시켰다. De-NOx 촉매 시스템에서 최대의 NOx 정화 효율에 적합한 환원제 분사 조건들의 선정이 필요하고, 분무 도달거리, 분무 평균 입경, 분무각, 분사량 등의 분무 특성과 환원제의 균일 분포를 잘 파악하여야 한다. 이와 같은 목적을 위하여 2차 분사에서 충돌판 형상에 의한 분무 및 거동 특성은 가시화 방법과 디지털 화상 처리 기법을 사용하여 분석하였으며, 충돌판 형상의 영향성과 각 형상에 대한 최적 각도 범위를 도출하였다.

화물창의 내부 세정은 압축공기 또는 고압수를 이용하고 있으나 전용 세정기를 이용하지 않은 경우 위험성이 높은 작업이다. 이 연구에서는 화물창 고압세척기를 개발하기 위해 분사노즐의 유동특성을 수치해석 기법을 적용하여 고찰하였다. 그 결과 입자의 크기는 영향은 크지 않았으며 공급압력이 높을수 록 노즐부 끝단에서 유속과 분사거리는 지수함수로 증가하였다.

The purpose of this research was to prepare silibininloaded nano sized liposomes to improve their aqueous solubility and to optimize the preparation method. For the preparation, specific amount of cholesterol was dissolved into ethanol. After that, phosphatidylcholine from egg yolk (~60%) was dissolved into mixture about 20, 40, and 60 mg/mL, and subsequently, silibin in was dissolved into organic phase at approximate 250, 500, and 1000 μg/mL, respectively. The organic phase was regularly injected at 0.9 mL/min into phosphate buffered saline (PBS) using peristaltic pump under stirring. Liposomes were formed spontaneously as soon as lipid phase was in contact with the aqueous phase. Then, the liposome suspension was kept under stirring for 15 min. Thereafter, ethanol was removed by rotary evaporation under reduced pressure. As the result, silibin in loaded liposomes were circular shape which had lipid bilayer at edge of the liposome droplets and were multilamellarvesicles. In addition, average size of silibinin loaded liposome droplets were 148.27, 144.52, and 173.46 nm at 250, 500, and 1000 μg/mL silibinin concentrations, respectively. Zeta potentials of liposome particles were showed about -9.64, -12.03, and -12.79 mV. As concentration of phosphatidylcholine in ethanol increased, droplet size and zeta potential of the liposome increased. The average encapsulation efficiency of obtained liposome suspensions was 57.6%. In conclusion, the liposome preparation method established can be used to encapsulate various hydrophobic bioactives for food application such as beverage.

Biodiesel as alternative energy source of the traditional petroleum fuels has increased interest, because environmental pollution based exhaust emissions from vehicle became serious. The advantage of biodiesel produced from esterification of vegetable and animal oils can be used without the modification of existing diesel engine, but glycerin is generated by production process. In this study, the usability of non-esterification biodiesel as an alternative fuel was investigated in a indirect injection diesel engine. The non-esterification biodiesel has not generated glycerin in esterification process and reduced the 20 percent of cost because it has not used methanol in the production process. Experiments were conducted by using the 5, 10 and 20 percentage of biodiesel and 4 and 8 percentage of biodiesel with 1 and 2 percentage of WDP in baseline diesel fuel. The smoke emission of biodiesel was reduced in comparison with diesel fuel, but power, torque and brake specific energy consumption was similar to diesel fuel.

Ni(OH)2 hollow spheres have been prepared by solvent displacement crystallization using a micro-injection device, and the effect of process parameters such as concentration and the relative ratio of the injection speed of the precursor solution, which is an aqueous solution of NiSO4·6H2O, to isopropyl alcohol of displacement solvent have been investigated. The crystal phases after NaOH treatment are in the β-phase for all process parameters. A higher concentration of NiSO4·6H2O aqueous solution is injected by a micro-injection device and bigger Ni(OH)2 hollow spheres with a narrower particle size distribution are formed. The crystallinity and hardness of the as-obtained powder are so poor that hydrothermal treatment of the as-obtained Ni(OH)2 at 120oC for 24 h in distilled water is performed in order to greatly improve the crystallinity. It is thought that a relative ratio of the injection speed of NiSO4·6H2O to that of isopropyl alcohol of at least more than 1 is preferable to synthesize Ni(OH)2 hollow spheres. It is confirmed that this solution- based process is very effective in synthesizing ceramic hollow spheres by simple adjustment of the process parameters such as the concentration and the injection speed.

A powder injection molding process is developed and optimized for piezoelectric PAN-PZT ceramics. Torque rheometer experiments are conducted to determine the optimal solids loading, and the rheological property of the feedstock is evaluated using a capillary rheometer. Appropriate debinding conditions are chosen using a thermal gravity analyzer, and the debound specimens are sintered using sintering conditions determined in a preliminary investigation. Piezoelectric performance measures, including the piezoelectric charge constant and dielectric constant, are measured to verify the developed process. The average values of the measured piezoelectric charge constant and dielectric constant are 455 pC/N and 1904, respectively. Powder injection molded piezoelectric ceramics produced by the optimized process show adequate piezoelectric performance compared to press-sintered piezoelectric ceramics.

PURPOSES: The objective of this study was to determine the optimum ratio of mix design, for a reclaimed asphalt pavement (RAP) content of 100%, for spray injection application. METHODS: A literature review revealed that spray injection is an efficient and cost-effective application for fixing small defective regions of an asphalt pavement. Rapid-setting polymer-modified asphalt mixtures prepared from two types of rapid-setting polymer asphalt emulsion were subjected to Marshall stability and wet track abrasion tests, in order to identify the optimum mix designs. RESULTS and CONCLUSIONS : Different mix designs of type A and type B emulsions were prepared using RAP and virgin aggregates, in order to compare the performance and determine the optimum mix design. The performance of mixtures prepared with RAP was superior to that of mixtures containing virgin aggregates. Moreover, for optimum ratio of the design, the binder content prepared from RAP was set to 1~2% lower than that consisting of virgin aggregates. Compared to their Type A counterparts, type B mixtures consisting of a reactive emulsion performed better in the Marshall stability and wet track abrasion tests. The initial results confirmed the advantages associated with using RAP for spray injection applications. Further studies will be performed to verify the difference in the optimum mix design and performance obtained in the lab-scale test and tests conducted at the job site by using the spray injection machine.

Powder injection molding (PIM), which combines the advantages of powder metallurgy and plastic injection molding technologies, has become one of the most efficient methods for the net-shape production of both metal and ceramic components. In this work, plasma display panel glass bodies are prepared by the PIM process. After sintering, the hot isostatic pressing (HIP) process is adopted for improving the density and mechanical properties of the PIMed glass bodies. The mechanical and thermal behaviors of the prepared specimens are analyzed through bending tests and dilatometric analysis, respectively. After HIPing, the flexural strength of the prepared glass body reaches up to 92.17 MPa, which is 1.273 and 2.178 times that of the fused glass body and PIMed bodies, respectively. Moreover, a thermal expansion coefficient of 7.816 × 10−6/oC is obtained, which coincides with that of the raw glass powder (7.5-8.0 × 10−6/oC), indicating that the glass body is fully densified after the HIP process.

Injection rate, injection quantity and injection timing of fuel are controlled precisely by electric control in CRDI system.Particularly, injection rate being influenced with injection pressure affects to spray characteristics and fuel-air ratio, so it is a very important factor in diesel combustion. In this study, injection rates in accordance with injection pressure at a constant ambient pressure were measured with Zeuch's method. Under the same condition, non-evaporating spray images were taken with a high speed camera and analyzed carefully with Adobe Photoshop CS3. Macroscopic spray characteristics and breakup processes in the spray could be found from the examined and analyzed data. Injection start time and injection period were practically affected with injection pressure. Also, initial injection rate, spray penetration, spray angle and breakup of high density droplets region in the spray were affected with injection pressure. The results and techniques of spray visualization and injection rate measurement in this study would be practically effective to study a high pressure diesel spray for common rail direct injection system.

Seven outbreaks of foot-and-mouth disease (FMD) have occurred in South Korea during the period January 2000-September 2015. The Korean government changed national goal to FMD-free country with vaccination after the November 2010 outbreak when approximately 3.5 million cattle and pigs were culled. With regard to vaccination, Korean pig producers have claimed that the occurrence of injection site reaction (inflammatory or non-inflammatory granuloma) is potentially associated with intensive vaccination campaign since 2011. The present study was undertaken to assess the incidence of injection site lesions in slaughtered pigs caused by FMD vaccination and the corresponding economic losses. Data obtained from two meat packers were classified into 3 vaccination periods: non-vaccination (July-November, 2010, n=96,959); one injection (July-November, 2014, n=162,089); and two injections (March-July, 2015, n=161,928). A total of 420,976 carcasses from 6,526 farms were analyzed. The incidence of the lesions was 18.6% for non-vaccination, 46.5% for one injection, and 73.7% for two injections. Economic loss per head slaughtered due to removal of the lesions was estimated to 1,302 won (US$ 1.1) for non-vaccination, 8,286 won (US$ 7.2) for one injection, and 17,378 won (US$ 15.1) for two injections (converted using 2015 exchange rate where Korean won 1,150 = 1 US$). It was estimated that the national annual losses excluding costs of an FMD vaccine and its application is US$ 115 million for one injection and US$ 241 million for two injections. The adoption of measures that cause minimal tissue damages and economic losses would appear to be of high priority.

목 적 : 복부 dynamic검사 시 조영제 주입 후 환자의 이상 반응 발생 빈도 및 조영제의 신호 대 잡음비 분석을 통해 적정한 조영제 주입 속도를 알아보고자 하였다. 대상 및 방법 : 2013년 4월부터 2014년 9월까지 3.0T MRI system(Magnetom Tim Trio, Siemens, Germany)을 이용하여 Gadoxetic acid(Primovist, Bayer Schering Pharma)를 사용한 309명(남자 223명, 여자 86명)을 대상으로 Liver dynamic검사를 하였고, Gadodiamide(Ominisacn, GE healthcare)을 사용한 247명(남자 148명, 여자 99명)을 대상으로 Cholangio, Pancreas MRI 상복부 검사를 시행하였다. Saline은 주입 속도를 조영제와 동일하게 주입했으며 그 양은 30ml로 고정하고 gadoxetic acid의 양은 0.1ml/kg, 조영제의 주입속도는 1.0cc/sec, 1.5cc/sec, 2.0cc/sec로 60sec, 100sec을 측정했다. Gadodiamide의 양은 0.2ml/kg, 조영제 주입 속도는 1.5cc/sec, 2.0cc/sec, 2.5cc/sec로 60sec, 120sec을 측정했으며 Volumetric Interpolated Breath-hold Examination(VIBE) sequence를 적용하여 영상을 획득하였다. 상복부 MRI검사 시 조영제의 주입속도에 따른 이상 반응 유무 및 발생 빈도를 분석하고 획득한 영상은 PACS viewer에서 각 phase 별로 ROI를 5~15mm로 main portal vein, liver parenchyma, aorta를 세 곳 설정하여 각 부위의 SNR을 60초, 100초, 120초 검사 중심으로 정량 분석하였다. 결 과 : Liver MRI의 arterial phase 시간대 이상 반응(일시적 호흡곤란, 기침, 구토, 가슴 답답함 등) 발생 빈도는 2.0cc/sec는 98명 중 23건(23.5%), 1.5cc/sec는 116명 중 44건(37.9%), 1.0cc/sec에서 95명 중 22건(23.2%)으로 나타났다. SNR은 조영제주입 속도를 2.0cc/sec로 했을 때 60초 검사에서 portal vein 439.13±38.26, liver parenchyma 250.54±28.54, aorta 311.74±33.24였고 100초에서는 312.01±20.29, 283.88±28.60, 250.38±22.68이었다. 1.5cc/sec의 경우 60초 검사에서 portal vein 415.81±42.43, parenchyma 247.14±28.24, aorta 305.48±30.16, 100초엔 각각 339.20±32.12, 273.65±29.28, 264.66±29.84였다. 1.0cc/sec의 경우 60초 검사는 portal vein 400.44±42.43, parenchyma 237.95±28.30, aorta 307.24±33.69, 100초는 359.17±31.67, 259.13±27.90, 280.49±32.74였다. Cholangio MRI는 2.5cc/sec는 90명 중 6명(6.7%), 2.0cc/sec는 87명 중 3명(3.4%), 1.5cc/sec에서 70명 중 4명(5.7%)이 arterial phase에서 이상 반응이 발생됐다. 신호대 잡음비는 2.5cc/sec로 조영제 주입 시 60초 검사에서 portal vein 659.09±59.10, liver parenchyma 367.40±39.09, aorta 537.40±41.82였으며 120초에서 각각 546.79±40.35, 376.15±28.79, 470.59±36.99였다. 2.0cc/sec로 주입했을 땐 60초에 portal vein 648.18±61.19, parenchyma 360.49±41.35, aorta 540.07±51.77이었고 120초는 각각 559.26±52.35, 343.70±38.27, 474.57±42.02였으며 1.5cc/sec로 주입 시엔 60초에 portal vein 637.62±54.24, parenchyma 358.85±42.87, aorta 544.25±47.16였고 120초는 562.35±39.57, 303.91±40.20, 481.22±40.14이었다. 결 론 : 조영제의 주입 속도를 2.0cc/sec로 했을 경우 Liver MRI는 저속 주입 시 보다 60초와 100초 검사에서 이상 반응의 증가없이 SNR이 더 좋은 영상을 획득했다. Cholangio MRI 또한 60초와 120초 검사에서 2.5cc/sec로 주입했을 때 저속 주입 시 보다 SNR이 더 우수한 영상을 얻을 수 있었다.

This study was developed the rapid heating and cooling device using peltier module for uniform cooling. make the rapid heating and cooling device(RCHD), for traditional water cooling device(TWCD) method and the rapid heating and cooling method warpage were compared and were analyzed and the materials used crystalline PP polymer. various warpage were compared for the process parameters such as packing pressure, packing time, mold temperature. in the crystalline PP polymer, TWCD method has higher warpage than RCHD method and show the result to be a bit more uniform cooling. RCHD method has higher warpage than TWCD method as cooling time and packing time increases and TWCD method has higher warpage than RCHD method as mold temperature increases.