본 연구는 교과서에서 엘니뇨 현상의 대기 순환과 관련하여 서술된 내용의 물리적 정합성 문제와 개념적 오류 를 분석하고, 현직 지구과학 교사들의 엘니뇨에 대한 이해 특성을 조사하였다. 이를 위해 2009 개정 교육과정과 2015 개정 교육과정의 고등학교 교과서 총 22종을 대상으로 엘니뇨 시기 열대 태평양의 기압, 무역풍, 워커 순환에 대한 설 명과 표현을 비교·분석하였다. 교과서 분석 결과, 일부 교과서에서 엘니뇨 시기의 기압 배치와 무역풍 형성 원리가 상 충되는 내용을 담고 있었으며, 무역풍이 서태평양 일부 해역에서 서풍 계열로 전환되는 관측 결과에도 불구하고 이를 열대 태평양 전역의 현상으로 서술하는 문제점이 발견되었다. 또한 워커 순환의 경우 교과서마다 상이한 형태로 제시되 면서도 이것이 실제 순환인지 편차를 나타내는 것인지에 대한 명확한 설명이 부족하였다. 현직 교사들을 대상으로 한 개념 조사에서는 평년값으로부터의 편차를 절대적 크기로 표현하거나 기압 배치와 무역풍의 물리적 관계성을 설명하는 데 있어 정합성이 부족한 특징이 나타났다. 특히 교사들이 제시한 워커 순환이 교과서의 서술 내용과 유사한 패턴을 보여, 교과서 내용의 제한점이 교사들의 이해에 영향을 주었을 가능성을 시사하였다.

The economical manufacturing of high-quality graphene has been a significant challenge in its large-scale application. Previously, we used molten Sn and Cu as the heat-transfer agent to produce multilayer graphene on the surface of gas bubbles in a bubble column. However, element Sn and Cu have poor catalytic activity toward methane pyrolysis. To further improve the yield of graphene, we have added active Ni into Sn to construct a Sn–Ni alloy in this work. The results show that Sn–Ni alloy is much more active for methane pyrolysis, and thus more graphene is obtained. However, the graphene product is more defective and thicker because of the faster growth rate. By using 300 ml molten Sn–Ni alloy (70 mm height) and 500 sccm source gas ( CH4:Ar = 1:9), this approach produces graphene with a rate of 0.61 g/hr and a conversion rate of methane to carbon of 37.9% at 1250 ℃ and ambient pressure. The resulting graphene has an average atom layer number of 22, a crumpled structure and good electrical conductivity.

본 연구는 대기 중 장기간 노출로 인해 열화된 Ni-rich NCM811(LiNi₀.₈Co₀.₁Mn₀.₁O₂) 양극 소재의 계면 저항 증가 및 전기화학적 성능 저하 문제를 해결하기 위해, 물리적 열처리 방법을 제안하였다. NCM811 양극 소재는 대기 중 수분 및 이산화탄소와의 반응에 의해 표면에 불순물이 형성되기 쉬우며, 이는 고체전해질과의 계면 저항을 증가시켜 전고 체전지 시스템에서의 성능 저하를 초래한다. 이러한 문제를 해결하기 위해, 열화된 NCM811 양극 소재를 O₂ 분위기 에서 열처리하여 표면의 불순물을 효과적으로 제거하고 양극 표면의 전도성을 향상시킴으로써, 양극-고체전해질 간의 계면 저항을 현저히 감소시키는 결과를 얻었다. SEM, XRD, ICP 분석을 통해 열화된 NCM811 양극 소재의 표면 특성 변화를 분석하였으며, 열처리 후 NCM811 소재의 계면 특성이 개선됨에 따라 전기화학적 성능 또한 상용 NCM811 소재와 유사한 수준으로 회복되는 것을 확인하였다. 특히, O₂ 분위기의 물리적 열처리 방법은 Ni-rich NCM811 양극 소재의 열화를 효과적으로 억제하고 고체전해질과의 계면 접촉을 개선하여, 황화물계 전고체전지의 전기화학적 성능 을 획기적으로 향상시킬 수 있는 유망한 기술임을 입증하였다. 이러한 결과는 전고체전지 상용화를 위한 핵심 전략으 로 적용될 수 있을 것으로 기대된다.

이 연구는 <사자춤 소년>을 통해 중국 애니메이션의 스토리텔링 특성과 동시대성 을 고찰했다. 이를 통해 문화적 전통과 현대의 결합으로 형성된 중국 애니메이션의 특성을 밝혔다. 분석방법은 트랜스아이덴티티를 활용했다. 이후 동시대성을 시사하는 중국 애국주의와 청년들의 특징을 제시했다. 분석결과, <사자춤 소년>은 동시대 부 유하는 중국 청년들의 ‘자기’ 중심적 정체성 횡단의 스토리텔링적 특성이 있었다. 또 한 사자춤은 현대 중국의 놀이문화이자, 청년 억압을 해소의 동시대 문화 공감대임 을 밝혔다.

Electrochemical water splitting presents an optimal approach for generating hydrogen ( H2), a highly promising alternative energy source. Nevertheless, the slow kinetics of the electrochemical oxygen evolution reaction (OER) and the exorbitant cost, limited availability, and susceptibility to oxidation of noble metal-based electrocatalysts have compelled scientists to investigate cost-effective and efficient electrocatalysts. Bimetallic nanostructured materials have been demonstrated to exhibit improved catalytic performances for the oxygen evolution reaction (OER). Herein, we report carbon aerogel (CA) decorated with different molar ratios of Fe and Ni with enhanced OER activity. Microwave irradiation was involved as a novel strategy during the synthesis process. Inductively coupled plasma mass spectrometry (ICP-MS), X-ray diffraction (XRD), X-ray Photoelectron Spectroscopy (XPS), Scanning Electron Microscope (SEM), Energy dispersive X-ray spectroscopy (EDAX spectra and EDAX mapping), Transmission Electron Microscope (TEM), High-Resolution Transmission Electron Microscope (HR-TEM), and Selected Area Electron Diffraction (SAED) were used for physical characterizations of as-prepared material. Electrochemical potential towards OER was examined through cyclic voltammetry (CV), chronoamperometry, and electrochemical impedance spectroscopy (EIS). The FeNi/CA with optimized molar ratios exhibits low overpotential 377 mV at 10 mAcm− 2, smaller Tafel slope (94.5 mV dec− 1), and high turnover frequency (1.09 s− 1 at 300 mV). Other electrocatalytic parameters were also calculated and compared with previously reported OER catalysts. Additionally, chronoamperometric studies confirmed excellent electrochemical stability, as the OER activity shows minimal change even after a stability test lasting 3600 s. Moreover, the bimetallic (Fe and Ni) carbon aerogel exhibits faster catalytic kinetics and higher conductivity than the monometallic (Fe), which was observed through EIS investigation. This research opens up possibilities for utilizing bi- or multi-metallic anchored carbon aerogel with high conductivities and exceptional electrocatalytic performances in electrochemical energy conversion.

Compared with the traditional Haber Bosch process, green and pollution-free electrocatalytic nitrogen reduction (NRR) has received considerable attention in the electrocatalysis field in the last decade. To address the issue of its low reactivity as well as the existence of competitive reactions, efficient electrocatalysts are particularly important. In this paper, NiO nanomaterials were synthesized by a simple water bath reaction. The effect of different calcination temperatures on the structure of NiO catalyst and its catalytic activity was studied. Uniform NiO-600 nanoparticles (56 ± 9.3 nm) obtained at 600 ℃ showed the best electrocatalytic NRR activity with an NH3 yield of 12 μg h− 1 mg− 1 and a Faraday efficiency of 5.5% at -0.5V (vs.RHE). The small particle size of the nanoparticles provided more active sites and the oxygen-rich vacancies facilitated the adsorption and activation of N2, which improved the catalytic activity of NiO-600. This study highlights the need for calcination temperature regulation and the huge impact on catalyst structure.

에너지 패러다임의 변화가 요구되는 현대에 수소는 매력적인 에너지원이다. 이러한 수소를 정제하는 기술 중에서 분리막을 이용한 기술은 저비용으로 고순도의 수소를 정제할 수 있는 기술로 주목받고 있다. 그러나 수소 분리 성능이 뛰어 난 팔라듐(Pd)은 가격이 매우 비싸 이를 대체한 소재가 필요하다. 본 연구에서는 수소 투과 성능은 좋으나 수소 취성에 약한 니오븀(Nb)과 수소 투과 성능은 떨어지나 내구성이 뛰어난 니켈(Ni)과 지르코늄(Zr)을 혼합한 합금으로 분리막을 제조하여 1~4 bar, 350~450 °C 조건에서 수소 투과 특성을 확인하였다. Pd를 코팅하지 않은 Ni48Nb32Zr20 분리막의 경우 최대 0.69 ml/cm2/min의 투과량을 보였으며, Pd가 코팅된 경우에는 최대 13.05 ml/cm2/min의 투과량을 보였다.

Ni-CNT nanocomposites were synthesized via the electrical explosion of wire (EEW) in acetone and deionized (DI) water liquid conditions with different CNT compositions. The change in the shape and properties of the Ni-CNT nanopowders were determined based on the type of fluids and CNT compositions. In every case, the Ni nanopowder had a spherical shape and the CNT powder had a tube shape. However, the Ni-CNT nanopowders obtained in DI water exhibited irregular shapes due to the oxidation of Ni. Phase analysis also revealed the existence of nickel oxide when using DI water, as well as some unknown peaks with acetone, which may form due to the metastable phase of Ni. Magnetic properties were investigated using a Vibrating Sample Magnetometer (VSM) for all cases. Nanopowders prepared in DI water conditions had better magnetic properties than those in acetone, as evidenced by the simultaneous formation of super paramagnetic NiO peaks and ferromagnetic Ni peaks. The DI water (Ni:CNT = 1:0.3) sample revealed better magnetic results than the DI water (Ni-CNT = 1:0.5) because it had less CNT contents.

Lead-free perovskite ceramics, which have excellent energy storage capabilities, are attracting attention owing to their high power density and rapid charge-discharge speed. Given that the energy-storage properties of perovskite ceramic capacitors are significantly improved by doping with various elements, modifying their chemical compositions is a fundamental strategy. This study investigated the effect of Zn doping on the microstructure and energy storage performance of potassium sodium niobate (KNN)-based ceramics. Two types of powders and their corresponding ceramics with compositions of (1-x)(K,Na)NbO3-xBi(Ni2/3Ta1/3)O3 (KNN-BNT) and (1-x)(K,Na)NbO3-xBi(Ni1/3Zn1/3Ta1/3) O3 (KNN-BNZT) were prepared via solid-state reactions. The results indicate that Zn doping retards grain growth, resulting in smaller grain sizes in Zn-doped KNN-BNZT than in KNN-BNT ceramics. Moreover, the Zn-doped KNNBNZT ceramics exhibited superior energy storage density and efficiency across all x values. Notably, 0.9KNN-0.1BNZT ceramics demonstrate an energy storage density and efficiency of 0.24 J/cm3 and 96%, respectively. These ceramics also exhibited excellent temperature and frequency stability. This study provides valuable insights into the design of KNNbased ceramic capacitors with enhanced energy storage capabilities through doping strategies.

In this study, Ni-Y2O3 powder was prepared by alloying recomposition oxidation sintering (AROS), solution combustion synthesis (SCS), and conventional mechanical alloying (MA). The microstructure and mechanical properties of the alloys were investigated by spark plasma sintering (SPS). Among the Ni-Y2O3 powders synthesized by the three methods, the AROS powder had approximately 5 nm of Y2O3 crystals uniformly distributed within the Ni particles, whereas the SCS powder contained a mixture of Ni and Y2O3 nanoparticles, and the MA powder formed small Y2O3 crystals on the surface of large Ni particles by milling the mixture of Ni and Y2O3. The average grain size of Y2O3 in the sintered alloys was approximately 15 nm, with the AROS sinter having the smallest, followed by the SCS sinter at 18 nm, and the MA sinter at 22 nm. The yield strength (YS) of the SCS- and MA-sintered alloys were 1511 and 1688 MPa, respectively, which are lower than the YS value of 1697 MPa for the AROS-sintered alloys. The AROS alloy exhibited improved strength compared to the alloys fabricated by SCS and conventional MA methods, primarily because of the increased strengthening from the finer Y2O3 particles and Ni grains.

This work describes Ni–Ce–Cu metallic–organic framework (MOF) for the detection of non-essential amino acid l-cysteine. The tri-metallic Ni–Ce–Cu MOF was synthesized via a solvothermal method. The cyclic voltammetry and the differential pulse voltammetry techniques were used to examine the electrochemical detection of l-cysteine. The Ni–Ce–Cu MOF shows an oxidation peak in PB solution at pH 3.0 between the potential range of 0.0 and 0.7 V and strong electro-catalytic activity toward the oxidation of l-cysteine across a wide linear range of 0.1 to 250 nM and low detection limit (LOD) was calculated of 1.56 nM. The analysis of l-cysteine in milk and egg yolk samples showed with recovery range of 96.75–103.5% and 97.78–99.43% with RSD% of 2.3–3.2% and 2.7–7.2%, respectively. These results show the Ni–Ce–Cu MOF has high selectivity for l-cysteine detection in milk and egg samples.

With the increasing attention to environmental pollution caused by particulate matter globally, the automotive industry has also become increasingly interested in particulate matter, especially particulate matter generated by automobile brake systems. Here, we designed a coating composition and analyzed its mechanical properties to reduce particulate matter generated by brake systems during braking of vehicles. We designed a composition to check the mechanical properties change by adding Cr3C2 and YSZ to the WC-Ni-Cr composite composition. Based on the designed composition, coating samples were manufactured, and the coating properties were analyzed by Vickers hardness and ball-on-disk tests. As a result of the experiments, we found that the hardness and friction coefficient of the coating increased as the amount of Cr3C2 added decreased. Furthermore, we found that the hardness of the coating layer decreased when YSZ was added at 20vol%, but the friction coefficient was higher than the composition with Cr3C2 addition.

본 연구는 에너지 저장 응용을 위한 PVI-PGMA/LiTFSI 고분자 막 전해질 및 CxNy-C 유연 전극의 합성 및 특성 에 관한 연구이다. 이중 기능을 갖는 PVI-PGMA 공중합체는 우수한 이온 전도성을 나타내었으며, PVI-GMA73/LiTFSI200 막 전해질은 1.0 × 10-3 S cm-1의 최고 전도도를 달성하였다. CxNy-C 전극의 전기화학적 성능을 체계적으로 분석하였으며, C3N2-C는 나노와이어와 다면체로 구성된 높은 연결성을 갖는 하이브리드 구조와 이중 Co/Ni 산화물을 포함하여 풍부한 산 화환원 활성 부위와 이온 확산을 용이하게 하는 특징으로 인해 958 F g-1의 최고용량 및 최소한의 전하 전달 저항(Rct)을 달성 하였다. 흑연 탄소 껍질의 존재는 충전-방전 동안 높은 전기화학적 안정성에 기여하였다. 이러한 결과들은 고성능 에너지 저 장 장치인 슈퍼커패시터 및 리튬 이온 전지와 같은 첨단 에너지 저장 장비에 PVI-PGMA/LiTFSI 고분자 막 전해질과 CxNy-C 전극을 활용하는 잠재력을 보여주었으며, 지속 가능하고 고성능의 에너지 저장 기술을 더욱 발전시키는 길을 열어가 고 있다.

Graphene-derived materials are an excellent electrode for electrochemical detection of heavy metals. In this study, a MnO2/ graphene supported on Ni foam electrode was prepared via ultrasonic impregnation and electrochemical deposition. The resulting electrode was used to detect Pb(II) in the aquatic environment. The graphene and MnO2 deposited on the Ni foam not only improved active surface area, but also promoted the electron transfer. The electrochemical performance towards Pb(II) was evaluated by cyclic voltammetry (CV) and square wave anodic stripping voltammetry (SWASV). The prepared electrode exhibited lower limit of detection (LOD, 0.2 μM (S/N = 3)) and good sensitivity (59.9 μAμM−1) for Pb(II) detection. Moreover, the prepared electrodes showed good stability and reproducibility. This excellent performance can be attributed to the strong adhesion force between graphene and MnO2, which provides compact structures for the enhancement of the mechanical stability. Thus, these combined results provide some technical considerations and scientific insights for the detection of heavy metal ions using composite electrodes.

To investigate the effect of the catalyst and metal–support interaction on the methane decomposition behavior and physical properties of the produced carbon, catalytic decomposition of methane (CDM) was studied using Ni/SiO2 catalysts with different metal–support interactions (synthesized based on the presence or absence of urea). During catalyst synthesis, the addition of urea led to uniform and stable precipitation of the Ni metal precursor on the SiO2 support to produce Ni-phyllosilicates that enhanced the metal–support interaction. The resulting catalyst upon reduction showed the formation of uniform Ni0 particles (< 10 nm) that were smaller than those of a catalyst prepared using a conventional impregnation method (~ 80 nm). The growth mechanisms of methane-decomposition-derived carbon nanotubes was base growth or tip growth according to the metal–support interaction of the catalysts synthesized with and without urea, respectively. As a result, the catalyst with Ni-phyllosilicates resulting from the addition of urea induced highly dispersed and strongly interacting Ni0 active sites and produced carbon nanotubes with a small and uniform diameter via the base-growth mechanism. Considering the results, such a Ni-phyllosilicate-based catalyst are expected to be suitable for industrial base grown carbon nanotube production and application since as-synthesized carbon nanotubes can be easily harvested and the catalyst can be regenerated without being consumed during carbon nanotube extraction process.

본 연구는 코팅 방법을 활용한 단결정 양극 소재 연구로서 Ni-rich계 다결정 양극 소재로 부터 단결정 양극 소재를 합 성하여 사이클 구동 시 양극 소재의 안정성을 향상시키고자 한다. 양극 소재에 LixCoO2와 LixSnO3 를 각각 코팅하여 이차입자 내부 혹은 외부에 코팅층이 형성된 양극 소재를 합성한 후 이를 소결하여 단결정 형성에 대한 영향을 비교 하였다. 입자 외부에 LixSnO3가 코팅되어 열처리 된 Ni0.8Co0.1Mn0.1O2(NCM811)의 경우 코팅 처리 없이 열처리된 양극 소재 보다 개선된 수명특성을 보였으나, 단결정화가 이뤄지지 않았다. 입자 내부에 LixCoO2 코팅층이 형성된 NCM811 을 열처리 한 결과 이차입자 내부에 형성된 Co 코팅층이 결정화되어 50회 사이클 후 기준 단결정 양극 소재의 방전용 량인 117.34 mAh·g-1 대비 129.11 mAh·g-1의 높은 방전용량을 나타내었고, 형상제어를 통해 이성적인 단결정화가 이뤄 졌다. 본 연구는 다결정체인 Ni-rich 양극소재의 단결정화에 대한 유요한 통찰력을 제공할 것으로 예상한다.

In this study, an Al82Ni7Co3Y8 (at%) bulk metallic glass is fabricated using gas-atomized Al82Ni7Co3Y8 metallic glass powder and subsequent spark plasma sintering (SPS). The effect of powder size on the consolidation of bulk metallic glass is considered by dividing it into 5 m or less and 20–45 m. The sintered Al82Ni7Co3Y8 bulk metallic glasses exhibit crystallization behavior and crystallization enthalpy similar to those of the Al82Ni7Co3Y8 powder with 5 m or less and it is confirmed that no crystallization occurred during the sintering process. From these results, we conclude that the Z-position-controlled spark plasma sintering process, using superplastic deformation by viscous flow in the supercooled liquid-phase region of amorphous powder, is an effective process for manufacturing bulk metallic glass.

High-temperature oxidation of a Ni-based superalloy was analyzed with samples taken from gas turbine blades, where the samples were heat-treated and thermally exposed. The effect of Cr/Ti/Al elements in the alloy on high temperature oxidation was investigated using an optical microscope, SEM/EDS, and TEM. A high-Cr/high-Ti oxide layer was formed on the blade surface under the heat-treated state considered to be the initial stage of high-temperature oxidation. In addition, a PFZ (γ’ precipitate free zone) accompanied by Cr carbide of Cr23C6 and high Cr-Co phase as a kind of TCP precipitation was formed under the surface layer. Pits of several μm depth containing high-Al content oxide was observed at the boundary between the oxide layer and PFZ. However, high temperature oxidation formed on the thermally exposed blade surface consisted of the following steps: ① Ti-oxide formation in the center of the oxide layer, ② Cr-oxide formation surrounding the inner oxide layer, and ③ Al-oxide formation in the pits directly under the Cr oxide layer. It is estimated that the Cr content of Ni-based superalloys improves the oxidation resistance of the alloy by forming dense oxide layer, but produced the σ or μ phase of TCP precipitation with the high-Cr component resulting in material brittleness.

Environmental issues such as global warming due to fossil fuel use are now major worldwide concerns, and interest in renewable and clean energy is growing. Of the various types of renewable energy, green hydrogen energy has recently attracted attention because of its eco-friendly and high-energy density. Electrochemical water splitting is considered a pollution-free means of producing clean hydrogen and oxygen and in large quantities. The development of non-noble electrocatalysts with low cost and high performance in water splitting has also attracted considerable attention. In this study, we successfully synthesized a NiCo2O4/NF electrode for an oxygen evolution reaction in alkaline water splitting using a hydrothermal method, which was followed by post-heat treatment. The effects of heat treatment on the electrochemical performance of the electrodes were evaluated under different heat-treatment conditions. The optimized NCO/NF-300 electrode showed an overpotential of 416 mV at a high current density of 50 mA/cm2 and a low Tafel slope (49.06 mV dec-1). It also showed excellent stability (due to the large surface area) and the lowest charge transfer resistance (12.59 Ω). The results suggested that our noble-metal free electrodes have great potential for use in developing alkaline electrolysis systems.

The overall process, from the pre-treatment of aluminum substrates to the eco-friendly neutral electroless Ni-P plating process, was observed, compared, and analysed. To remove the surface oxide layer on the aluminum substrate and aid Ni-P plating, a zincation process was carried out. After the second zincation treatment, it was confirmed that a mostly uniform Zn layer was formed and the surface oxide of aluminum was also removed. The Ni-P electroless plating films were formed on the secondary zincated aluminum substrate using electroless plating solutions of pH 4.5 and neutral pH 7.0, respectively, while changing the plating bath temperature. When a neutral pH7.0 electroless solution was used, the Ni-P plating layer was uniformly formed even at the plating bath temperature of 50 oC, and the plating speed was remarkably increased as the bath temperature was increased. On the other hand, when a pH 4.5 Ni-P electroless solution was used, a Ni-P plating film was not formed at a plating bath temperature of 50 oC, and the plating speed was very slow compared to pH 7.0, although plating speed increased with increasing bath temperature. In the P contents, the P concentration of the neutral pH 7.0 Ni-P electroless plating layer was reduced by ~ 42.3 % compared to pH 4.5. Structurally, all of the Ni-P electroless plating layers formed in the pH 4.5 solution and the neutral (pH 7.0) solution had an amorphous crystal structure, as a Ni-P compound, regardless of the plating bath temperature.