초고층 구조물 및 특수 구조물의 수요 증가로 별도 다짐 없이도 타설 가능한 고유동 콘크리트에 대한 연구가 활발히 진행되고 있다. 고유동 콘크리트는 유동화제 사용 및 다양한 시멘트계 재료로 배합 되는데, 배합실패 또는 유동화제의 과다 첨가 등으로 인해 타설 시 콘크리트 재료분리를 발생 시킬 수 있다. 재료분리는 블리딩 및 골재의 침하로 콘크리트 내구성에 큰 영향을 미치기 때문에 정확하게 평가하여야 한다. 이에 따라, 습식체가름에 따른 기존 평가 방법의 한계점을 보완하기 위해 전기비저항 측정을 이용하여 고유동 콘크리트의 재료분리에 끼치는 영향을 분석하고 평가하고자 하였다.

As a result of this study, the testor penetration resistance and the hardness of the durometer are considered highly correlated and are thought to be effective when using the durometer to determine the setting time in the field structure.

Recently, high-performance and high-fluidity concrete have been studied and developed because high-rised build is constructed. An early-age properties of these concretes have been studied and developed bacause of comparing existed concrete. This study proposed non-destructive method as electrical resistivity measurement, which evaluates setting time of cement-based materials. An assessment of the effect on the setting time was studied on the addition of a superplasticizer to delay the setting time and the curing temperature to promote the setting time. 6th of samples prepared mortar according to adding superplasticizer(PNS) or curing temperature and measured the electrical resistivity during 24 h. As the results, mortars which curing higher temperature were promoted rising time which is setting time in the electrical resistivity, also mortars which adding superplasticizer were retard rising time.

Recently, high-performance and high-fluidity concrete have been studied and developed because high-rised build is constructed. high-performance and self-consolidating concrete is demanded high strength as low w/cm and fluidity as adding superplasticizer. However, these superplasticizer are changed early-age property such as bleeding, segregation and late setting time etc. This study persents the setting time of fluidity mortars evaluated using the measurement of eletrical resistivity. 7th Samples prepared mortars which were adding polycarboxylate type superplasticizer(Ester) or poly naphthalene sulfonate(PNS) and measured the electrical resisitivity during 24 h. As a results, mortars which added superplasticizers were late rising time which is setting time in measurement of electrical resistivity. However, degree of hardening of PNS mortar were higher than Ester mortar.

본 연구는 다성분계 고유동 모르타르의 특성에 관한 연구이다. 보통 포틀랜드 시멘트(OPC), 고로슬래그 미분말(GGBFS), 칼슘설포알루미네이트(CSA) 그리고 초속경시멘트(URSC)를 혼합한 결합재이다. GGBFS는 OPC 질량에 대해 30%(P7 series), 50%(P5 series) 그리고 70%(P3 series)치환하였고, CSA와 URSC는 10%와 20%를 치환하였다. 혼화제는 폴리카르복실계를 사용하였다. 모든 배합의 물-결합재 비(w/b)는 0.35로 일정하다. 실험은 미니슬럼프, V-funnel, 압축강도 그리고 건조수축을 측정하였다. 실험결과 CSA와 URSC의 치환율이 증가하면 혼화제 사용량, V-funnel 시간 그리고 압축강도는 증가하였다. 또한 응결시간과 건조수축은 CSA와 URSC의 치환율이 증가함에 따라 감소하였다. CSA는 건조수축을 감소시키지만 URSC는 효과가 미미하다. CSA와 URSC를 혼합한 결합제는 상호보완 작용에 의해 건조수축 감소효과가 컸다. 이는 URSC의 초기강도 향상효과와 CSA의 팽창과 장기강도 향상효과 때문이다.

This research presents the results of the strength and drying shrinkage properties to study the effect of ground granulated blast furnace slag(GGBFS), fly ash(FA) and calcium sulfoaluminate(CSA) for activated ternary blended slag cement. The activated ternary blended cement(ATBC) mortar were prepared having a constant water-cementitious materials ratios of 0.4. The GGBFS contents ratios of 100%, 80%, 70% and 60%, FA replacement ratios of 10%, 20%, 30% and 40%, CSA ratios of 0%, 10%, 20% and 30% were designed. The superplasticizer of polycarboxylate type were used. The activator was used of 10% sodium hydroxide(NaOH) + 10% sodium silicate(Na2SiO3) by weight of binder. Test were conducted for mini slump, setting time, V-funnel, water absorption, compressive strength and drying shrinkage. According to the experimental results, the contents of superplasticizer, V-funnel and compressive strength increases with an increase in CSA contents for all mixtures. Moreover, the setting time, water absorption ratios and drying shrinkage ratio decrease with and increase in CSA. One of the major reason for the increase of strength and decrease of drying shrinkage is the accelerated reactivity of GGBFS with alkali activator and CSA. The CSA contents is the main parameter to explain the strength development and decreased drying shrinkage in the ATBC.

A Controlled Low-Strength Materials (CLSM) is suitable for mine backfilling because it does not require compaction owing to it high fluidity and can be installed quickly. Therefore, a CLSM utilizing CO2-solidified Circulating Fluidzed Bed Combustion (CFBC) coal ash was developed and it’s properties were investigated, since. CO2-solidification of CFBC coal ash can inhibit exudation of heavy metals. The chemical composition and specific surface area of Pulverized coal Combustion fly ash and CFBC fly ash were analyzed. The water ratio, compressive strength and length change ratio of CLSM were confirmed. The water ratios differed with the specific surface area of the CLSM. It was confirmed that the porosity of CLSM affected its compressive strength and length change ratio.

최근 건설현장에서 작업자의 고령화 및 숙련공 부족 현상이 중요 문제로 부각되고 있으며, 또한 최근 건설구조물이 점차 고층화, 대형화됨에 따라 부재의 형상이 복잡해지고 있다. 이러한 건설 환경의 변화에 따라 국내 및 국외에서 고유동 콘크리트에 대한 연구 및 개발이 증대되고 있다. 고유동 콘크리트는 재료분리 없이 굳지 않은 콘크리트의 유동성을 개선시켜 다짐 작업 없이 자기 충전이 가능한 콘크리트를 말한다. 하지만 고유동 콘크리트는 인장 및 휨 강도의 저하와 균열 등의 문제점을 가지고 있다. 따라서 본 연구에서는 문제점을 해결하기 위하여 고유동 콘크리트에 양마섬유를 혼입하였다. 양마섬유의 경우 천연섬유로 친환경적이며 이산화탄소의 흡수량이 많아 콘크리트 생산과정에서 배출되는 이산화탄소의 양을 상쇄시킬 수 있을 것으로 보인다. 또한, 기존 콘크리트의 섬유 보강재로 사용되었던 황마와 유사한 특성을 지녔으며 짧은 생육 기간으로 대량생산이 가능하여 경제적이다. 양마섬유는 섬유 표면이 거칠어 콘크리트와의 부착력이 뛰어나고 섬유의 인장력이 우수하여 콘크리트의 인장강도 증진과 균열 저감 효과가 있을 것으로 사료된다. 또한, 산업부산물의 일종인 플라이애쉬와 고로슬래그를 혼입하여 탄소저감 효과와 폐기물의 처리로 환경적인 측면에서 긍정적인 효과가 기대된다. 따라서 본 연구에서는 이와 같은 재료로 시멘트의 일부를 대체하여 양마섬유를 혼입한 고유동 콘크리트의 강도 특성을 알아보고자 하였다.

본 연구는 규산나트륨(Na2SiO3)으로 활성화된 고유동 대량치환슬래그 시멘트의 기초특성에 관한 연구이다. 고로슬래그 미분말 (GGBFS)은 보통포틀랜드 시멘트(OPC)의 40%에서 80%까지 질량치환하고 칼슘설포알루미네이트(CSA)는 2.5%와 5.0% 치환하였다. 규산나 트륨(Na2SiO3)은 전체 결합재(OPC+GGBFS+CSA) 질량의 2%와 4% 추가하였다. 모든 배합의 물-결합재 비(w/b)는 0.35이다. 본 연구에서는 미니슬럼프, V-funnel, 응결시간, 압축강도와 건조수축을 측정하였다. 실험결과 유동화제 양, V-funnel, 응결시간과 건조수축은 CSA와 Na2SiO3가 증가함에 따라 감소하였다. 그러나 압축강도는 CSA와 Na2SiO3가 증가함에 따라 증가하였다. 이러한 원인 중 하나는 CSA와 Na2SiO3가 GGBFS의 활성화를 촉진하였기 때문이다. 최고의 성능을 나타낸 배합은 CSA 5.0% + Na2SiO3 4%를 혼합한 시험체이다.

The mechanical properties were evaluated to examine the optimum adding amount of AC and UT viscosity agent by mixing two viscosity agent according to the adding ratio. When the ratio of AC and UT viscosity agent was 5:5, It was most suited for high-fluidity concrete with low binders by increasing workability and effect of reducing viscosity.

The flowability and compressive strength were evaluated to examine the effect of biner mixing ratio on the high-fluidity concrete with low binders. When the binder mixing ratio (OPC, BFS, FA) was 7:2:1, It was most suited for high-fluidity concrete with low binders by increasing workability and compressive strength.

The mechanical properties were evaluated to examine the optimum adding amount of AC and UT viscosity agent by mixing two viscosity agent according to the adding ratio. When the ratio of AC and UT viscosity agent was 5:5, It was most suited for high-fluidity concrete with low binders by increasing workability and effect of reducing viscosity.

The flowability and compressive strength were evaluated to examine the effect of biner mixing ratio on the high-fluidity concrete with low binders. When the binder mixing ratio (OPC, BFS, FA) was 7:2:1, It was most suited for high-fluidity concrete with low binders by increasing workability and compressive strength.

In this study, CO2 reduction type quaternary component high fluidity concrete was produced with more than 80%r eduction in cement quantity to increase the use of industrial by product sand enhance construction performance, there by reducing CO2 emissions. Furthermore, theq uality properties, and CO2 reduction performance of this concrete were evaluated. As a result of the quality evaluation of quaternary component blended high fluidity concrete with CO₂reduction, the target performance could be achieved with a 80% or more reduction of cement quantity by mixing a large amount of industrial byproducts. The required performance level was obtained even though the flow, mechanics, and durability characteristics decreased a little compared to conventional mix.

This paper presents an experimental study investigating the bond characteristic of steel bars (D13, D16) on fluidity concrete mixed with recycled marble powder under tensile loads. Experimental results showed that average bond strengths of D13 series specimens and D13 series specimens were 18.00MPa and 15.67MPa respectively, and that specimen with the larger diameter of rebar that adhesion strength had the lower bond strength.

본 연구에서는 고압송용 고유동콘크리트 개발을 위한 기초적인 연구의 일환으로 펌프압송시 압송관내 콘크리트가 받는 압력을 재 현할 수 있는 가압장치를 개발하였다. 이를 통하여 펌프압송할 경우 발생되는 품질변화의 원인 중 압력에 의한 단위수량 감소에 중점을 두어 가 압에 따른 콘크리트용 굵은골재의 흡수 특성 및 고유동콘크리트 내부 굵은골재의 흡수 특성을 평가하였으며, 고유동콘크리트의 가압 전·후 압 축강도를 평가하였다. 실험결과, 250 bar의 높은 압력이 작용할 경우 부순굵은골재 및 강자갈의 흡수율은 표건 흡수율 이상으로 증가되지 않는 것으로 나타났으며, 경량굵은골재의 흡수율은 표건 흡수율 이상으로 증가되는 것으로 나타났다.

This study was evaluated the field applicability of high fluidity concrete for pc sleeper using high volume fly ash.

In this study, viscosity was minimized for production of viscosity-agent type high fluidity concrete with normal strength, and segregation resistance was maximized with viscosity agent and use of superplasticizer. Their applicability and physical property were examined.