Stainless steel is used in many industrial fields due to its excellent properties such as workability, strength, ductility, and corrosion resistance, and various properties required in the manufacturing field depending on the constituent components. pump impellers used in seawater and underwater require high corrosion resistance and high rigidity to prevent corrosion and damage, so they are a representative part group to which Stainless materials are applied. Through the introduction of the CMT(Cold Metal Transfer) process, a manufacturing method through WAAM(Wire Arc Additive Manufacturing) technology, which has advantages of lower production cost and excellent fatigue strength compared to the existing casting method, is being proposed. Recently, prior research on the WAAM process has been conducted on various materials, but most of the research results published so far are focused on the DED(Direct Energy Deposition) process, and a good WAAM shape design study using austenitic stainless steel is lacking. in this study, using the CMT process, the relationship between the change in bead shape and process parameters was confirmed in the BoP(Bead on Plate) welding experiment using wire made of austenitic stainless steel STS-308.

Because of the International Maritime Organization(IMO)'s regulation to regulate emissions of ships, a change is taking place to replace ship fuels from Heavy Fule Oil(HFO) to Liquefied Natural Gas(LNG). In the case of LNG, it is a material obtained by liquefying Natural Gas(NG), and it is -163 degrees below zero, and the volume is reduced to 1/600 level. The material of the tank that can store LNG must be a material that can safely store LNG in a cryogenic environment, and the materials of the tank that can store LNG are limited in the International Code of the Construction and Equipment of Ships Carrying Liquefied Gases in Bulk(IGC Code). Among the materials listed in the IGC Code, 9% nickel steel is used as a material for LNG fuel propulsion tanks that are recently ordered because of relatively high mechanical properties under cryogenic environments. In this study, the mechanical properties of butt welds were measured following the weld reliability evaluation of Flux Cored Arc Welding(FCAW) butt welds made of 9% nickel steel by PARTI. The measured mechanical properties are tensile strength, bending strength, hardness, and cryogenic impact test required by the classification for Welding Procedure Specification(WPS) approval.

Because of the International Maritime Organization(IMO)'s regulation to regulate emissions of ships, a change is taking place to replace ship fuels from Heavy Fule Oil(HFO) to Liquefied Natural Gas(LNG). In the case of LNG, it is a material obtained by liquefying Natural Gas(NG), and it is -163 degrees below zero, and the volume is reduced to 1/600 level. The material of the tank that can store LNG must be a material that can safely store LNG in a cryogenic environment, and the materials of the tank that can store LNG are limited in the International Code of the Construction and Equipment of Ships Carrying Liquefied Gases in Bulk(IGC Code). Among the materials listed in the IGC Code, 9% nickel steel is used as a material for LNG fuel propulsion tanks that are recently ordered because of relatively high mechanical properties under cryogenic environments. In this study, butt welding was performed on a 9% nickel steel material using Flux Cored Arc Welding(FCAW), the most widely used welding method in shipyards. In PARTI, after securing the welding conditions, cross-sectional observation results analysis, liquid penetrating test, and radiographic test were performed to verify the reliability of the weld.

알루미늄합금 6061-T6 판재에 대하여 마찰교반용접과 텅스텐 이너트 가스 용접의 교차 용접부의 미세조직과 기계적 특성에 있어서 용접 순서의 영향을 분석하기 위한 시험편을 성공적으로 제작하였다. FSW-ED 시험편이 다른 조합들보다 가장 좋은 기계적 특성을 나타내었다. 흥미롭게도, TIG-FSW ED 시험편이 FSW-TIG ED 시험편보다 높은 인장강도를 나타내었다. 용접부 경도의 경우, FSW 시편이 TIG-FSW 및 FSW-TIG 시험편보다 높은 값을 나타내었고, TIG-FSW 시험편이 FSW-TIG 시험편보다 높은 값을 나타내었다. FE-SEM을 이용한 인장 파면에 대한 관찰을 통하여, 모든 시험편에서 연성파괴를 나타내는 다양한 크기의 딤플들이 관찰되었다. FSW-TIG 시험편의 파면에서는 용융지(熔融池) 표면 영역에서 기공들이 관찰되는 반면, TIG-FSW 시험편에서는 기공의 형성은 관찰되지 않았다. 경도와 미세조직의 결과를 통해 TIG-FSW 공정이 FSW-TIG 공정보다 높은 인장강도를 확보할 수 있는 공정임을 확인하였다.

As the International Maritime Organization (IMO)'s environmental regulations on ship emissions become strict, the demand for ships powered by Liquefied Natural Gas (LNG) is rapidly increasing worldwide. Compared to other materials, high manganese steel has the advantages of superior impact toughness at cryogenic temperatures, a small coefficient of thermal expansion, and low cost of base materials and welding rods. However, there is a limitation in that the mechanical properties of the filler material are lower than the base material having excellent mechanical properties. In this study, after performing a high manganese steel laser butt welding experiment, the welding performance was evaluated through mechanical property (yield strength, tensile strength, hardness, cryogenic impact strength) tests of the weld. As a result, it was observed that the yield strength and tensile strength of the high manganese steel laser welding part was 97.5% and 93.5% of the base metal respectively. Also the hardness of welding part was 84.2% of the base metal. The cryogenic impact strength of the welding part and the base metal were over the 27J, the level of welding part is 76.1% of the base metal.

The bead geometry according to the welding conditions was analyzed through the laser fillet welding experiment of 9% Ni steel, and the relationship between the shear strength and the five bead geometry measured by selecting the main bead geometry of the fillet weld was analyzed. Among the welding conditions, the welding conditions that directly affect the penetration depth are welding speed and laser power, and the working angle and beam position have a great influence on the formation of leg of vertical and horizontal members. The bead shape, which greatly affects the shear strength, is the horizontal member length, neck thickness, and weld length, and has a proportional relationship with the shear strength. As a result of confirming the relationship between shear strength and bead shape through the derivation of the trend line, it was confirmed that the length of the vertical member, whose R2 value was 0.92, was most closely related to the shear strength.

In this study, Equivalent fracture strain and Fracture energy were evaluated with the small punch test(SP test) for friction stir welded(FSW) Al6061-T6 sheets. With the three rotation speeds and the three feeding rate, The nine different conditions of FSW were prepared for the SP test. The SP test specimens were manufactured and tested on the advancing side, center, and retreating side to the tool rotation direction. From the SP test data, the equivalent fracture strain and the fracture energy were analyzed. The high value of equivalent fracture strain was attained form tool rotational speed 900RPM and feeding rate 330mm/min. It is found that its characteristic is about 14% higher than the value of condition 1100RPM-330mm/min that have the lowest value. The high value of fracture energy was obtained from the tool rotation speed 900RPM and feeding rate 330mm/min. The lowest fracture energy, which from 1000RPM-300mm/min, was approximately 16% difference to the highest value.

P92 steel weldment scheduled to use for next generation ultra super critical(USC) boiler header is assessed on creep characteristics. The test method to assess local structure of weldment is small-punch creep(SP-Creep) test, which is a kind of micro test proved the availability on evaluation of mechanical property for local structure. The results for P92 steel weldment are compared with that of tensile creep test for same microstructures of steel weldment. Overall, the creep resistance of coarse grain HAZ(CGHAZ) at 650℃ is inferior to the other structures while fine grain HAZ(FGHAZ) is most superior in the P92 steel weldment. The power law relationships can be obtained for each weldment structures(BM, ICHAZ, FGHAZ, CGHAZ and W.M) of USC boiler header

구조용 강재의 용접부는 강재(Base metal, BM), 용접모재(Weld metal, WM), 열영향부(Heat affected zone, HAZ)로 구성된다. 용접부를 구성하는 이들 세 부분의 구조적 성질은 서로 다를 것이므로, 강재의 용접부의 구조 거동은 BM, WM, HAZ로 구성된 복합체의 거동으로 고려할 수 있다. 본 연구에서는 용접부를 구성하는 BM, WM, HAZ 각각의 탄성계수를 나노압입으로 도출하고, 이들의 복합거동(composite action)을 고려한 용접부의 등가탄성계수(equivalent elastic modulus)를 산정하였다.

국내에서 개발중인 콘크리트 저장용기는 방사성 물질의 격납 건전성을 유지하기 위하여 내부에 캐니스터를 포함하고 있다. 본 논문에서는 콘크리트 저장용기 내부 캐니스터의 뚜껑 용접시, 용접시간 저감과 이에 따른 캐니스터 용접부의 구조적 건 전성을 확보하기 위한 방안으로, 정상, 비정상 및 사고조건에서 캐니스터 용접부 균열을 진전시키는 하중에 의해 발생되는 균열 깊이를 분석하여, 용접부의 최대 허용결함깊이를 평가하였다. 정상, 비정상 및 사고조건에서의 구조해석은 범용 유한 요소해석 프로그램인 ABAQUS를 사용하였으며, 허용결함깊이는 ASME B&PV Code Section XI에 따라 막응력과 조합하중 에 대해 평가하였다. 평가결과 콘크리트 저장용기의 캐니스터 용접부의 허용결함깊이는 18.75 mm로 평가되었으며, 이는 NUREG-1536에서 권고하고 있는 임계결함깊이를 만족하고 있는 것으로 나타났다.

There is a growing demand for improving the welding quality by reducing the machining error and improving the quality of the machined surface in the beveling for the improvement of the welding groove of the thick plate. For this purpose, it is necessary to develop an automatic beveling machine that adopts a cutting method that replaces the conventional oxygen flame cutting method. In this study, the cutting characteristics according to the machining conditions were evaluated during the face milling applied to the thick plate welding groove. We measured and evaluated cutting force for the machining conditions such as cutting depth, feed rate, chamfer angle, workpiece material, and material of the tool. We expect that this study is used as basic data for designing the stiffness of the spindle, the strength of the fixture and the power of the spindle and the feeding device when designing the automatic beveling machine.

The chassis frame generally consists of side members, cross beams, and several mounting brackets. Strength and fatigue behaviors of welded joints between members and brackets in a frame are a very complex phenomena, which comes basically due to the structural geometry, non-homogeneous material, and welding residual stresses. Therefore, the prediction of fatigue life for the welded structure is very difficult compared to that for the simple geometry. This paper presents the structural and fatigue analysis results for a body frame and welded joints under system durability loads. In order to fatigue assessment of welded joints, local stress approach is used for its simplicity, which is based on the several empirical S-N curves that are associated with welded joint types and loading modes. The estimated fatigue cycles of the welded areas in a frame were satisfied the target cycles under system load conditions.

In this study, the effect of the friction stir welding (FSW) was compared with that of the gas tungsten arc welding (GTAW) on the microstructure and microhardness of Cu-Ni alloy weldment. The weldment of 10 mm thickness was fabricated by FSW and GTAW, respectively. Both weldments were compared with each other by optical microstructure, microhardness test and grain size measurement. Results of this study suggest that the microhardness decreased from the base metal (BM) to the heat affected zone (HAZ) and increased at fusion zone (FZ) of GTAW and stir zone (SZ) of FSW. the minimum Hv value of both weldment was obtained at HAZ, respectively, which represents the softening zone, whereas Hv value of FSW weldment was little higher than that of GTAW weldment. These phenomena can be explained by the grain size difference between HAZs of each weldment. Grain size was increased at the HAZ during FSW and GTAW. Because FSW is a solid-state joining process obtaining the lower heat-input generated by rotating shoulder than heat generated in the arc of GTAW.

The dissertation is on the measurement of the strain caused by the characteristics and the temperature changes of the TIG welded zone which is used with 3D ESPI system that is functionally modified through the laser ESPI system. Experimental results have derived from the fact that the welded zone has micro crack during the various phased of the process such as rolling, alkali cleaning, air cooling and heat processing due to the repetitious up-and-down of the temperature. Especially, both 60℃ and 90℃ are selected to measure the strain on the welded zone which can be effected by these two temperatures in the manufacturing process. The flat plate differences between ESPI and the strain gage are within 2 %, and they are the exactly same with the results from the temperature changes of 60 ℃ and 90 ℃, and also within 3 % and 4 %. As the tensile load increase, the strain of aluminum material increases linearly. Also the same effect are observed as the temperature goes up with irregular-line type. The comparison of the strain by ESPI and the strain gage in the welded specimen is within the 2.6% when it is under the room temperature and low-load conditions, while it is measured within 3 % under the high load condition.

The purpose of this study is to determine more variables in welding characteristics of ATOS(Steel for Automobile Structure) 80 high tensile steel available in market, and examine how welding characteristics of ATOS 80 vary depending on changes in improvement angle of welding sections. In regard to major characteristics of this study, it focused on analyzing welding characteristics of ATOS 80 by changing improvement angle of welding sections into 40°, 50° and 60° and by changing root gap into 2㎜ and 3㎜. And it also used radiograph test to examine observations of major defects on welding section.