The operating parameters considered in this study include evaporating and condensing temperature, degree of subcooling and degree of superheating. in R744-R717 cascade refrigeration system and R744 two-stage compression refrigeration system with the range of low temperature -50℃∼-30℃. The coefficient of performance(COP) of R744-R717 cascade refrigeration system is about 16∼20% greater than that of R744 two-stage compression refrigeration system in the range of evaporation temperature of -50℃∼-30℃. R744 two-stage compression refrigeration system is unstable because its coefficient of performance changes significantly depending on the evaporating temperature and total compression work, and compression efficiency decreases. In this case, not efficient for long-term use. Whereas R744-R717 R744-R717 is a cascade refrigeration system using eco-friendly refrigerants. And this system is a high-efficiency refrigeration system that performs well even under various operating conditions. This is why it can be configured by selecting a refrigerant suitable for the high temperature side and the low temperature side.

Wastewater management is increasingly emphasizing economic and environmental sustainability. Traditional methods in sewage treatment plants have significant implications for the environment and the economy due to power and chemical consumption, and sludge generation. To address these challenges, a study was conducted to develop the Intermittent Cycle Extended Aeration System (ICEAS). This approach was implemented as the primary technique in a full-scale wastewater treatment facility, utilizing key operational factors within the standard Sequencing Batch Reactor (SBR) process. The optimal operational approach, identified in this study, was put into practice at the research facility from January 2020 to December 2022. By implementing management strategies within the biological reactor, it was shown that maintaining and reducing chemical quantities, sludge generation, power consumption, and related costs could yield economic benefits. Moreover, adapting operations to influent characteristics and seasonal conditions allowed for efficient blower operation, reducing unnecessary electricity consumption and ensuring proper dissolved oxygen levels. Despite annual increases in influent flow rate and concentration, this study demonstrated the ability to maintain and reduce sludge production, electricity consumption, and chemical usage. Additionally, systematic responses to emergencies and abnormal situations significantly contributed to economic, technical, and environmental benefits.

밭농업의 일관화를 위해 개발된 복합작업기의 효율적인 운영전략은 연료절감의 목표와 함께 저속 로터리작업의 품질에도 중점을 두어야 한다. 본 연구는 둥근 두둑 복합작업기의 작업품질을 유지하는 적정조건에서 동력과 연료소비를 계상하고 비교하여 집약적 밭농업에서의 효율적인 작업기 운용전략을 제안하려 하였다. PTO 표준 시험성적을 이용한 Kim 모델은 임의의 부분 부하 상태에서 연료소비량(FC), 비체적 연료소비율(SVFC) 및 단위면적당 연료소비율(FCA)를 구하고 셀선도(shell diagram)를 얻을 수 있다. 따라서 개발된 복합작업기에 적용할 카테고리 1 트랙터(DK450)와 카테고리 2 트랙터(PX800)를 선정하고 적정운용 조건에서의 연료소비 특성을 비교하였다. 이전 연구를 바탕으로 이론적인 목표 작업속도는 3.0<SPDth<4.0km/h와 로터리 피치(p)가 35<p<47cm/rev인 범위를 적정한 작업 기준(criteria)으로 하여 운용조건을 선택하였다. 각 트랙터에서 적정한 운용조건의 사례들을 비교하면 작은 트랙터(DK 450)를 사용함으로써 얻을 수 있는 연료소비 절약율은 FC가 19.4%, SVFC가 21.1% 그리고 FCA가 29.9% 정도로 평가된다.

Diesel engine has the advantages of strong power, low fuel consumption and good durability, so it has been widely used in transportation, automobile, ship and other fields. However, the nitrogen oxides(NOx) and particulate matter(PM) emitted by diesel engines have become one of the main causes of air pollution. Especially during idling, the engine temperature is low, and there are more residual exhaust gases in the combustion chamber, resulting in the formation of more harmful emissions. In this study, performance of a single cylinder, four-stroke, direct injection (DI) diesel engine fueled with diesel–biodiesel mixtures has been experimentally investigated. The findings show that a remarkable improvement in PM–NOx trade-off can be achieved by burning diesel-bioethanol blend fuels.

The precipitation effect of Al-6%Si-0.4%Mg-0.9%Cu-(Ti) alloy (in wt.%) after various heat treatments was studied using a laser flash device (LFA) and differential scanning calorimetry (DSC). Solid solution treatment was performed at 535 oC for 6 h, followed by water cooling, and samples were artificially aged in air at 180 oC and 220 oC for 5 h. The titanium-free alloy Al-6%Si-0.4%Mg-0.9%Cu showed higher thermal diffusivity than did the Al-6%Si-0.4%Mg-0.9%Cu-0.2%Ti alloy over the entire temperature range. In the temperature ranges below 200 oC and above 300 oC, the value of thermal diffusivity decreased with increasing temperature. As the sample temperature increased between 200 oC and 400 oC, phase precipitation occurred. From the results of DSC analysis, the temperature dependence of the change in thermal diffusivity in the temperature range between 200 oC and 400 oC was strongly influenced by the precipitation of θ'-Al2Cu, β'-Mg2Si, and Si phases. The most important factor in the temperature dependence of thermal diffusivity was Si precipitation.

In this study, blending oils of diesel oil and butanol were used as fuel oil for diesel engine to measure combustion pressure, fuel consumption, air ratio and exhaust gas emission due to various operating conditions such as engine revolution and torque. Using these data, the results of analyzing the engine performance, combustion characteristics and exhaust emission characteristics such as NOx (nitrogen oxides), CO2 (carbon dioxide), CO (carbon monoxide) and soot were as follows. The fuel conversion efficiency at each load was highest when driven in the engine revolution determined by a fixed pitch propeller law. Except 30% butanol blending oil, fuel conversion efficiency of the other fuel oils increased as the load increased. Compared to diesel oil, using 10% and 20% butanol blending oil as fuel oil was advantageous in terms of thermal efficiency, but it did not have a significant impact on the reduction of exhaust gas emissions. On the other hand, future research is needed on the results of the 20% butanol blending oil showing lower or similar levels of smoke concentration and carbon monoxide emission rate other than those types of diesel oil.

CKD 추출액은 시멘트공정에서 발생한 폐기물인 CKD를 시멘트 원료로 재사용하기 위해 공정 방해물질로 작용하는 KCl을 추출한 폐수이며, 폐수처리시설 증설 등의 문제로 추출액 무방류 및 이를 재이용하고자 하였다. 이온교환법을 적용하여 KCl을 제거한 결과, 이온교환 후 추출액의 pH는 12.7 에서 pH 2 미만으로 감소하였으며 양이온교환수지의 H+가 이온교환을 거쳐 추출액에 용해되었음을 확인하였다. 이온교환의 선택성에 의해 Ca2+, K+ 순서로 제거되었으며, K+ 이온을 제거하기 위해 접촉시 간의 증가가 필요함을 판단하였다. 이온교환수지와 직접접촉시간이 약 6배 높은 접촉시간을 갖는 회분 식장치에서 연속흐름식장치 대비 4배 높은 K+ 제거 효율을, 7배 높은 Cl- 제거 효율을 확인하였다. 양이온교환수지의 H+가 음이온교환수지의 OH- 대비 1.2배 빠른 교환속도를 가짐을 추출액 pH 변화를 통해 확인하였다.

In this study, the performances of the refrigeration unit for the box under actual operating conditions were examined by using the constant temperature and humidity chamber (air enthalpy method). For this purpose, the degree of superheat, pressure, and temperature were measured while changing the EEV opening, the compressor speed, the outdoor temperature, and the load in the refrigeration cycle of the refrigeration unit. The highest cooling performance was found at EEV 33%. However, EEV 35% with low compression ratio and degree of superheat was the most reliable in terms of reliability. Considering the compressor speed and cooling performance, the refrigeration unit was in an optimal condition at the compressor speed 3,040RPM. The results of this study will be provided as basic data for the optimal design of refrigeration units for box.

In order to apply rotary atomizer to agricultural spraying system, the motor direct coupled rotary atomizer was proposed. The effect of operating conditions such as atomizing air flow rate, working fluid flow rate, and rotation speed of spinning cup on the atomization performance was investigated for the proposed direct coupled rotary atomizer. The motor speed was controlled in the range of 6,000 to 12,000 rpm using an alternating current transformer, and the atomizing air was supplied by the compressor. In this study, LDPA was used to analyze the spray characteristics of the rotary atomizer. The representative particle diameters of D10, SMD, MMD, D90, and DMax tended to decrease as the atomizing air flow rate and the motor speed increased, but increased as the working fluid flow rate increased. Also, SMD was found to be influenced by order of atomizing air flow rate> motor speed> working fluid flow rate, and DMax was influenced by order of operating fluid supply> motor speed> atomizing air flow rate.

막증발 (Membrane Distillation, MD) 기술은 역삼투 해수담수화 공정에서 발생하는 농축수의 처리 문제를 해결하고 공정 회수율을 증가시킬 수 있는 차세대 담수화 기술로 부각되고 있다. 하지만 MD 공정의 효율적 운영을 위해서는, 막의 오염 (Fouling) 및 젖음 (Wetting) 현상을 해결하여야 한다. 이 현상들은, 해수 속에 존재하는 성분, 막의 종류 등을 포함한 여러 가지 운영 조건 등에 따라 다를 수 있다. 따라서 본 연구에서는 막오염과 막젖음 현상이 어떻게 발생하는지 살펴보기 위해, MD 공정 운영 조건을 변화시키며 막투수도 및 여과저항, 처리수 전도도 등을 측정하고, SEM-EDX, LEP (Liquid Entry Pressure) 등을 이용하여 막을 분석하였다.

천연가스, 산업공정, 화석연료의 연소과정과 같은 대규모 고정 배출원에서 발생하는 온실가스인 CO2를 포집하기 위한 기술 개발이 전 세계적으로 활발하게 수행되고 있다. 특히, 습식 흡수 법은 비교적 낮은 CO2분압에서도 높은 제거 효율을 달성할 수 있어 많은 개발이 이루어져온 포집 기술이다. 하지만 흡수제의 재생에 필요한 에너지가 과다한 문제가 있으며, 충분한 부지가 확보되어야하기 때문에 공정 상용화에는 큰 걸림돌이 있다. 이러한 문제를 극복하고 공정 효율을 개선 할 수 있는 접촉분리막 공정 기술이 최근 주목받고 있다. 본 연구에서는 접촉분리막과 화학적 습식 아민 흡수제를 이용한 이산화탄소 제거 특성을 분석하였다.

본 연구에서는 선박용 엔진을 활용하여 E2, E3 사이클 시험 결과로부터 연료 내 황 함유량 변화에 따른 대기오염물질 배출 특성을 조사하였다. 테스트를 위해 사용된 엔진은 360 PS의 엔진(Doosan L126TIH engine)을 활용하였고, 동력계로는 Horiba-Schenck사의 400㎾급 동력계인 W400을 사용하였다. 엔진에서 발생되는 대기오염물질 계측을 위해서는 오스트리아 AVL사의 FTIR과 SPC 장비를 배기라인 후단에 장착해서 사용하였다. 실험 결과로는 E2, E3 사이클 모두에서 연료 내 황 함유량이 증가할수록 THC와 CO의 단위 출력 당 배출량은 감소하고 입자상물질은 증가하였다. 연료의 황 함유량이 증가할수록 동점도가 증가되어 엔진의 연료소모율이 좋아지는 것을 확인하였다. 이는 본 연구에 사용된 엔진의 경우 연료 분사압력이 일정한 상태에서 동점도 증가에 따른 분무입자의 평균입경이 커짐에 따른 연소 상태가 개선되었기 때문이라 생각되어진다. 질소산화물의 경우 이번 연구에서는 황함유량의 변화에도 배출량에서는 큰 변화를 보이지 않았다.

Forward osmosis (FO) process has been attracting attention for its potential applications such as industrial wastewater treatment, wastewater reclamation and seawater desalination. Particularly, in terms of fouling reversibility and operating energy consumption, the FO process is assumed to be preferable to the reverse osmosis (RO) process. Despite these advantages, there is a difficulty in the empirical step due to the lack of separation and recovery techniques of the draw solution. Therefore, rather than using FO alone, recent developments of the FO process have adapted a hybrid system without draw solution separation/recovery systems, such as the FO-RO osmotic dilution system. In this study, we investigated the performance of the hollow fiber FO module according to various operating conditions. The change of permeate flow rate according to the flow rates of the draw and feed solutions in the process operation is a factor that increases the permeate flow rate, one of the performance factors in the positive osmosis process. Our results reveal that flow rates of draw and feed solutions affect the membrane performance, such as the water flux and the reverse solute flux. Moreover, use of hydraulic pressure on the feed side was shown to yield slightly higher flux than the case without applied pressure. Thus, optimizing the operating conditions is important in the hollow fiber FO system.

열유도상분리법(TIPS) 및 연신의 복합공정으로 막증류(Membrane distillation, MD)용의 소수성 및 다공성 PVDF 중공사 분리막을 제조하였다. 제조된 분리막을 막증류 공정에 적용하여 처리수량을 극대화하기 위한 방안으로 모듈의 형태와 운전조건 및 병렬 연결 시 배관의 크기 영향을 확인하고자 하였다. 진공 막증류 모듈의 최적화 실험에서는 모듈 내 분리막의 충진율과 길이가 증가할수록 플럭스는 감소하며, 진공포트의 위치는 모듈을 수직으로 연결하였을 때 원수의 inlet 방향에 위 치할수록 플럭스 측면에서 가장 유리한 것으로 확인되었다. 모듈의 헤더배관의 크기선정에서는 중공사막의 내경면적과 헤더 배관의 내경면적이 동일할 경우 최대 플럭스를 나타냄을 확인할 수 있었으며, 모듈 내 선속도가 높을수록 높은 플럭스를 나타내지만 모듈에 작용하는 압력 역시 비례하여 증가하기 때문에 최적 선속도를 찾는 것이 필요하다.