Radiant tubes heat exchangers are critical components that facilitate the heat transfer process to steel in an annealing furnace, and it addresses several engineering problems, such as thermal stress and mechanical failure due to long-term thermal cycling, which can significantly affect the longevity of the tubes and maintenance requirements. In this study, we used commercial software (ANSYS) to simulate the thermal stress and deformation of radiant tubes subjected to extreme thermal conditions and pressure loads. We evaluated both thermally induced deformation and creep deformation, which is a time-dependent deformation under constant stress over the long term. The results showed that uneven temperature conditions and pressure loads lead to significant deformation and potential failures. To mitigate these engineering challenges, we also tested several designs that include supporting brackets. This study provides valuable insights for designing radiant tube heat exchangers in annealing furnaces to extend their lifespan and ensure system safety.

Heat shock proteins (HSPs) are highly conserved cellular proteins that contribute to adaptive responses of organisms to a variety of stressors. In response to stressors, cellular levels of HSPs are increased and play critical roles in protein stability, folding and molecular trafficking. The mRNA expression pattern of two well-known heat shock protein transcripts, HSP70 and HSP90 were studied in two tissues of nerve ganglia, cerebral ganglion and pleuropedal ganglion of Pacific abalone (Haliotis discus hannai). It was observed that both HSP70 and HSP90 transcripts were upregulated under heat stress in both ganglion tissues. Expression level of HSP70 was found higher than HSP90 in both ganglia whereas cerebral ganglion showed higher expression than pleuropedal ganglion. The HSP70 and HSP90 showed higher expression at Day-1 after exposed to heat stress, later decreased at Day-3 and Day-7 onwards. The present result suggested that HSP70 and HSP90 synthesize in nerve ganglion tissues and may provide efficient protection from stress.

In this analysis, the analytical model was verified through the normal mode analysis of the piston for the 2.9 liter IDI (indirect injection) engine. Heat transfer analysis was carried out by selecting two cases of applied temperature using the validated model. The first case was a condition of 350℃ on the piston upper surface and 100℃ on the piston body and inner wall. In the second case, the conditions were set to give a temperature of 400℃ on the upper surface of the piston and 100℃ on the piston body and the inner wall. In addition, the temperature distribution due to heat transfer was obtained for the pistons with boundary conditions of two cases, and then the thermal stress distribution due to thermal expansion was obtained using the input. Using this analysis result, the thermal stress caused by thermal expansion due to the thermal conduction of the piston is examined and used as the basic data for design.

The results of internal temperature. productivity and immunity analysis of the laying hen house by the thermal environment and the supply of cold drinking water were as follows. The external temperature was changed from the minimum of 18℃ at night and the maximum of 36℃ during the day, and the internal temperature of the laying hens varied from 20~31℃. Thermal imaging analysis showed that the body temperature of the laying hen decreased by 2.4℃ with the supply of drinking water. The laying hen amount increased 2.36g and laying hen rate increased 3.62%p. Albumin increased 6.1%, decreased AST 15%, and decreased cholesterol 12.7%. Immune activators increased and T cells and B cells increased to increase immunity.

PURPOSES : It is well known that low temperature cracking is one of the most serious distresses on asphalt pavement, especially for northern U.S. (including Alaska), Canada and the northern part of south Korea. The risk of thermal cracking can be numerically measured by estimating thermal stress of a given asphalt mixture. This thermal stress can be computed by low temperature creep testing. Currently, in-direct tensile (IDT) mixture creep test mentioned in AASHTO specification is used for measuring low temperature creep properties of a given asphalt mixture. However, IDT requires the use of expensive testing equipment for performing the sophisticated analysis process, however, very few laboratories utilize this equipment. In this paper, a new and simple performance test (SPT) method: bending beam rheometer (BBR) mixture creep testing equipment is introduced, and the estimated experimental results were compared with those of conventional IDT tests. METHODS: Three different asphalt mixtures containing reclaimed asphalt pavement (RAP) and roofing shingles were prepared in the Korea Expressway Corporation (KEC) research laboratory. Using the BBR and IDT, the low temperature creep stiffness data were measured and subsequently computed. Using a simple power-law function, the creep stiffness data were converted into relaxation modulus, and subsequently compared. Finally, thermal stress results were computed from relaxation modulus master curve using Gaussian quadrature approach with condierations of 24 Gauss number. RESULTS: In the case of the conventional asphalt mixture, similar trends were observed when the relaxation modulus and thermal stress results were compared. In the case of RAP and Shingle added mixtures, relatively different computation results were obtained. It can be estimated that different experimental surroundings and specimen sizes affected the results. CONCLUSIONS: It can be said that the BBR mixture creep test can be a more viable approach for measuring low temperature properties of asphalt mixture compared to expensive and complex IDT testing methods. However, more extensive research and analysis are required to further verify the feasibility of the BBR mixture creep test.

As a case study on aspect ratio behavior, Kaolin, zeolite, TiO2, pozzolan and diatomaceous earth minerals are investigated using wet milling with 0.3 pai media. The grinding process using small media of 0.3 pai is suitable for current work processing applications. Primary particles with average particle size distribution D50, ~6 μm are shifted to submicron size, D50 ~0.6 μm, after grinding. Grinding of particles is characterized by various size parameters such as sphericity as geometric shape, equivalent diameter, and average particle size distribution. Herein, we systematically provide an overview of factors affecting the primary particle size reduction. Energy consumption for grinding is determined using classical grinding laws, including Rittinger's and Kick's laws. Submicron size is obtained at maximum frictional shear stress. Alterations in properties of wettability, heat resistance, thermal conductivity, and adhesion increase with increasing particle surface area. In the comparison of the aspect ratio of the submicron powder, the air heat conductivity and the total heat release amount increase 68 % and 2 times, respectively.

Sex hormones including progesterons, androgens, and estrogens are influential in differentiation of ovarian tissues and competence of fertility. These steroid hormones derived from cholesterol are required for cumulus-oocyte complexes(COCs) during oocyte maturation. COCs is a total functional and active entity playing a central role in oocyte. Lipid metabolism in the mammalian COCs is controlled by environmental factors. The intracellular cholesterol contents go through remarkable changes. It plays an important part of oocyte developmental competence. However, heat stress affects steroid hormone by decreasing progesterone, estrogen concentrations, and resumption of meiosis in COCs maturation. Reduction of the hormone and meiotic resumption might lead to the decline of ovarian function, follicle maturation, and subsequent embryogenesis. In the same vein, heat stress also influence on germinal vesicle breakdown, lipolytic variations, and loss of the nuclear envelope in the course of maturation of oocytes. In summary, we examined the effects of thermal stress on oocyte maturation through steroid hormone contents of change identifying the molecular mechanisms of lipids metabolism. It may have the solution to further the therapy methods for disorders regarding sterility.

Previous studies have shown that Lonicera caerulea has a chemical protective effect. Phenolic and vitamin C contained in Lonicera caerulea prevent cancer, diabetes and cardiovascular disease, lower blood pressure and delay the aging process. However, the antioxidant mechanism of male reproductive system to heat stress is still unknown. Male reproductive system is very sensitive to heat. When scrotum temperature increase, oxidative stress can occur. Oxidative stress affects sperm motility and spermatogenesis, resulting in infertility. Therefore, we investigated the antioxidant effect of L. Caerulea in male genitalia by inducing oxidative stress by artificially exposing the testicles to heat at 42 ° C. The experiment was performed by dividing the ICR mouse into four groups. Each group is n = 5. Control group (C) and heat stress group (HS) were oral gavage administered D.W. Honey berry group (HB) and Honeyberry / heat stress group (HB + HS) were oral gavage administered honey berry (250mg / kg / day). HS groups (n=5, per n=5) received heat stress by exposing their lower bodies in the water bath at 42℃ for 30 minutes. We confirmed that there was a significant difference in the motility, morphology and the number of sperms using CASA(computer-assisted semen analysis). Lipid peroxidation assay results showed heat causes oxidative stress in serum. This study is conducting to investigate the antioxidant effect of L. Caerulea. Histologically analyzed the testicular form of each group, the activity level of heat shock protein and the level of reactive oxygen species were measured by Western blot and the level of catalase and HSP-90 was examined by RT-PCR analysis. Thus, studies of testicular morphology, sperm kinetics, hormone levels, heat shock protein expression and antioxidant enzymes under heat stress have shown that L. Caerulea ingestion has Anti-oxidant and thermal protective activity on the testis by heat damage.

PURPOSES : Thermal cracking (also called low-temperature cracking) is a serious stress for asphalt pavement, especially in eastern South Korea, the northern USA, and Canada. Thermal cracking occurs when the level of thermal stress exceeds the corresponding level of low temperature strength of the given asphalt materials. Therefore, computation of thermal stress is a key factor for understanding, quantifying, and evaluating the level of low-temperature cracking resistance of asphalt pavement. In this paper, two different approaches for computing thermal stress on asphalt binder were introduced: Hopkins and Hamming’s algorithm (1967) and the application of a simple power-law function. All the computed results were compared visually; then the findings and recommendations were discussed. METHODS: Thermal stress of the tested asphalt binder was computed based on the methodology introduced in previous literatures related to viscoelastic theory. To perform the numerical analysis, MATLABTM 2D matrix-correlation and Microsoft Excel visual basic code were developed and used for the function fitting and value-minimization processes, respectively. RESULTS : Different results from thermal stress were observed with application of different computation approaches. This variation of the data trends could be recognized not only visually but also statistically. CONCLUSIONS: It can be concluded that these two different computation approaches can successfully provide upper and lower limits (i.e. boundaries) for thermal stress prediction of a given asphalt binder. Based on these findings, more reliable and reasonable thermal stress results could be provided and finally, better pavement performance predictions could also be expected.

Low temperature cracking on asphalt material is one of the serious distresses for asphalt pavement built in northern U.S., Europe and Canada. Thermal stress is a key factor for measuring (and estimating) the resistant capability of asphalt pavement against low temperature cracking. For this reason, many road agencies have recognized thermal stress as a crucial parameter for evaluating the low temperature performance of asphalt pavement materials. Thermal stress is conventionally computed through two steps. First, the relaxation modulus E(t) is generated thorough the conversion of the experimental creep compliance data D(t). Then thermal stress (T℃) is numerically estimated solving convolution integral. In this paper, a one-step approach to the calculation of thermal stress is proposed. This method is based on Laplace transformation. Thermal stress and corresponding critical cracking temperature obtained with single- and double-step procedure on a set of three mixtures are graphically and statistically compared. It is observed that the application of Laplace transformation provides reliable computation results of thermal stress compared to the conventional computation approach.

Bemisia tabaci is a vector of Tomato yellow leaf curl virus (TYLCV) but Trialeurodes vaporariorum is not. To determine the effect of TYLCV acquisition on vector and non-vector, we compared various physiological characteristics between two species. Our results showed that TYLCV acquisition significantly affected B. tabaci but not T. vaporariorum. The B. tabaci increased susceptibility against thermal stress but weakened chill coma recovery, shortening of longevity, low fecundity and abbreviated developmental time by virus acquisition. At the molecular level, B. tabaci increased hsp70 and hsp90 levels by TYLCV ingestion. However, T. vaporariorum did not shown any changes of those characteristics. Therefore, the physiological manipulation of TYLCV was specific to vector species but not non-vector species.

섬유강화 복합재료는 열팽창 계수의 방향성을 갖고 있을 뿐만 아니라 제작과정 온도와 실제 사용온도 사이의 차이 때문에 필연적으로 열응력 효과를 받게 된다. 이러한 열응력에 의한 파손현상은 실제 항공우주산업에서의 응용이 증대되고 있는 두 꺼운 복합 적층판의 경우에 더욱 현저한 현상으로 적층판의 역학적 기능 및 파단강도에 큰 영향을 미치게 된다. 본 연구에서 는 복잡한 재질로 구성되고 높은 세장비를 가진 블레이드 날개 구조의 차원축소 및 열 응력 복원 이론을 소개하고 3차원 유 한요소모델과 비교결과를 통해 효율성과 정확성을 입증한다. 또한 차원을 축소한 모델링을 구성하고 복원이론를 이용하여 열적 환경에 적용된 복합재 보 단면의 열응력을 차원 복원하고 시각적으로 형상화하는 효율적인 복원해석 과정을 소개하고 자 한다.

FK506BP는 일명 FK506 binding protein 12이라 불리는 작은 펩티드로서 single 도메인을 가진 다. FK506BP는 면역반응 억제, 산화적 스트레스 및 염증과 관련이 있다. 본 연구의 목적은 참돔 (Pagrus major)을 저수온(8℃, 33 psu) 및 저염분(20℃, 10 psu) 상태에 노출시킨 후, FK506BP 유 전자의 발현을 관찰하는 것이다. 연구결과, FK506BP 유전자의 발현은 저수온(8℃, 33 psu) 및 저 염분(20℃, 10 psu)상태에서 유의적으로 증가하는 것으로 나타났다. 이 연구결과로서 FK506BP 유전자는 수온 및 염분 등의 환경 스트레스에 대한 생체지표유전자로서 역할을 한다고 제의 한다.

The sweetpotato whitefly Bemisia tabaci is a serious pest and virus vector of many crops. To understand thermal tolerance of B. tabaci at molecular level, effects of rapid and acclimated thermal stress were analyzed by measuring mRNA levels of two heat shock proteins (hsp), hsp23 and hsp90, of B. tabaci using quantitative real-time RT-PCR. Mortality of adult whiteflies were 65.5% by 45°C for 1 h but 100% by 50°C for 1 h. However, mortality by subsequent exposures to 35°C for 1 h then 45°C for 1 h was 43.3%. Comparison between rapid and acclimated heat shock treatments showed that different patterns between hsp23 and hsp90 levels. At acclimated condition, hsp90 was higher but hsp23 was lower than rapid heat shock. The results suggest that the heat acclimation response is possibly advantageous to whiteflies that are often exposed to drastic temperature fluctuations.