Research has been conducted on acoustic metamaterials that control the transmission characteristics of reflected and refracted waves using phase delay by resonators. Using one-dimensional theory, the phase delay equations for the 1/4 wavelength and Helmholtz resonator are presented. These one-dimensional analysis results are compared with the results predicted by three-dimensional FEM. The advantages and disadvantages of 1/4 wavelength and Helmholtz resonator were confirmed in implementing phase delay. An acoustic metamaterial with a refraction angle of 30° was manufactured using multiple tubes and then the sound pressure distribution was measured. A relatively large sound pressure was measured at the target position of 30°, which was compared with the 3D FEM analysis results. Simulations confirmed that a phase delay range closer to 2π was more effective in refraction, but varying the number of resonators was found to have minimal impact on which additional research is needed for generalization.

The structural integrity of concrete silos is important from the perspective of long-term operation of radioactive waste repository. Recently, the application of acoustic emission (AE) is considered as a promising technology for the systematic real-time health monitoring of concrete-like brittle material. In this study, the characteristics of AE wave propagation through concrete silo of Gyeongju radioactive waste repository were evaluated under the effects of groundwater and temperature for the quantitative damage assessment. The attenuation coefficients and absolute energies of AE waves were measured for the temperature cases of 15, 45, 75°C under dry and saturated concrete specimens, which were manufactured based on the concrete mix same as that of Gyeongju concrete silo. The geometric spreading and material loss were taken into account with regard to the wave attenuation coefficient. The attenuation coefficient shows a decreasing pattern with temperature rise for both dry and saturated specimens. The AE waves in saturated condition attenuate faster than those in dry condition. It is found that the effect of water content has a greater impact on the wave attenuation than the temperature. The results from this study will be used as valuable information for estimating the quantitative damage at the location micro-cracks are generated rather than the AE sensor location.

Single OLED and tandem OLED was manufactured to analyze the electroluminescence characteristics of DC driving, AC driving, and full-wave rectification driving. The threshold voltage of OLED was the highest in DC driving, and the lowest in full-wave rectification driving due to an improvement of current injection characteristics. The luminance at a driving voltage lower than 10.5 V (8,534 cd/m2) of single OLED and 20 V (7,377 cd/m2) of a tandem OLED showed that the full-wave rectification drive is higher than that of DC drive. The luminous efficiency of OLED is higher in full-wave rectification driving than in DC driving at low voltage, but decrease at high voltage. The full-wave rectification power source may obtain higher current density, higher luminance, and higher current efficiency than the AC power source. In addition, it was confirmed that the characteristics of AC driving and full-wave rectification driving can be predicted from DC driving characteristics by comparing the measured values and calculated values of AC driving and full-wave rectification driving emission characteristics. From the above results, it can be seen that OLED lighting with improved electroluminescence characteristics compared to DC driving is possible using full-wave rectification driving and tandem OLED.

본 연구에서는 해운대 해수욕장의 내습파랑특성과 해빈면적 변화와의 상관성을 파악하였으며, 파랑특성요소를 독립변수로 설정하고 해빈면적 일변화량을 종속변수로 하는 회귀분석을 수행하여 전체 및 세부구간(서측, 중앙, 동측)에 대한 해빈면적 변화량 산출식을 도 출하였다. 도출된 해빈면적 변화량 산출식에 약 10개월의 파랑관측자료를 대입하여 계산된 해빈면적과 실제 관측면적과의 비교를 통해 해빈면적 변화량 산출식의 정확도를 평가하고 해빈면적 변동특성을 분석하였다. 분석 결과, 해빈면적 변화량 산출식의 정확도는 평균 해빈폭 기준 1.5 ~ 2.7 m의 오차를 나타내었으며, 실제 관측면적과의 상관계수는 0.91 ~ 0.94의 분포를 보이며 매우 유사한 해빈면적 변화양상을 나타내었다. 또한, 세부구간별로 해빈면적 변화에 영향을 크게 미치는 파랑특성요소가 서측구간은 파향, 중앙구간은 파고, 동측구간은 파고와 주기인 것을 알 수 있었다. 이를 통해 연안정비사업이 해운대 해수욕장의 해빈면적 변동특성에 미치는 영향 및 연안정비사업의 효과를 파악할 수 있었다. 본 연구에서 도출된 해빈면적 변화량 산출식은 정도 높은 파랑예측자료가 확보될 경우 유의미한 장기간 해빈면적 변화 예측이 가능하므로 연안침식에 대한 선제적 대응 대책 수립 시 의사결정의 근거가 될 수 있는 기초자료 확보에 기여할 수 있을 것으로 기대 된다.

This study defines Korean wave stars as Korean wave human brands and examines the influence of the characteristics, attachment, and self-congruity of the Korean wave human brand on brand equity. For this, this study surveyed Chinese female consumers in their 20s and 30s who consume many Korean wave products from May 2018 to June 2018. First, human brand characteristics, attachment, self-congruity, Korean wave aspiration level, and brand equity according to demographic characteristics were identified. Second, characteristics, attachment, self-congruity, and the aspiration level of the Korean wave human brand showed correlations with brand equity. However, brand awareness, a sub-factor of brand equity, does not show correlations with self-congruity. Third, characteristics, attachment, self-congruity, and Korean wave aspiration level had a positively influenced brand equity. Fourth, when looking into the mediated effect of attachment on brand equity, both human brand characteristics and self-congruity showed a partially mediated effect. Fifth, when analyzing the adjustment effect in the Korean wave aspiration level, a group with higher Korean wave aspiration level showed more correlations with attachment and brand equity. This study found that attachment and self congruity are important elements in forming human brand and brand equity. This study is significant in that it verified the influence of Korean wave brand power that has been on the rise recently on brand equity and provided a theoretical basis that has allowed researchers to determine that the characteristics, attachment, and self-congruity of Korean wave human brand significantly influence brand equity.

When a train enters a tunnel, a pressure wave is generated. This pressure wave propagates in the tunnel and emits as micro pressure wave at the opposite tunnel exit. This pressure wave could appear as a sound pulse in a particular environment and cause hazardous effects on the environment near the tunnel exit. When planning tunnels, it is necessary to take appropriate measures to reduce the magnitude of the micro pressure wave. In this study, we investigated the existing micro pressure wave management standards and studied the signal processing method and the sound evaluation method which were used in setting the appropriate management standard for the evaluation of the micro pressure wave.

Information and communication technologies are developing rapidly as IC chip size becomes smaller and information processing becomes faster. With this development, digital circuit technology is being widely applied to mobile phones, wireless LANs, mobile terminals, and digital communications, in which high frequency range of GHz is used. In highdensity electronic circuits, issues of noise and EMC(Electro-Magnetic Compatibility) arising from cross talk between interconnects or devices should be solved. In this study, sheet-type electromagnetic wave absorbers that cause electromagnetic wave attenuation are fabricated using composites based on soft magnetic metal powder and silicon rubber to solve the problem of electromagnetic waves generated in wireless communication products operating at the frequency range of 2.4 GHz. Sendust(Fe-Si-Al) and carbonyl iron(Fe-C) were used as soft magnetic metals, and their concentrations and sheet thicknesses were varied. Using soft magnetic metal powder, a sheet is fabricated to exhibit maximum electromagnetic attenuation in the target frequency band, and a value of 34.2dB(99.9 % absorption) is achieved at the target frequency.

In this paper, optical infrared thermography simulation using thermal wave imaging technique is performed to analyze the thermal characteristics of delamination defects. In this study, lock-in thermography(LIT) and pulsed thermography(PT) simulation was performed to analyze the samples of european traditional tiles with delamination defects, and the analytical modeler was developed through the ANSYS 19.2 transient thermal analysis tool. Applied sinusoidal heating with modulation frequency according to pulse heating and phase locking technique. The thermal response of the sample surface by heating was recorded and then data analysis was performed. The temperature gradient characteristics of each technique were compared, and phase angle was calculated for the LIT to analyze the parameters for the experiment setting. The simulation model was developed as a useful data for practical optical infrared thermography tests.

다중적층구조는 상대적으로 두꺼운 주 적층구조(ply)와 얇은 층간구조(interlayer)를 반복하여 붙여서 만들어진다. 적층구조의 동적 파괴 페리다이나믹 해석을 효율적으로 수행하기 위해 주 적층구조만 실제 페리다이나믹 절점으로 모델링하고 층간구조는 가상의 절점으로 간략히 모델링하는 비국부 가상 층간구조 모델링 기법을 도입한다. 이를 통해 얇은 층간구조의 수치적 이산화 정도는 무시하고 상대적으로 두꺼운 주 적층구조를 해석하기에 적절한 수준의 수치적 이산화만으로 효율적인 페리다이나믹 모델링 및 해석을 수행할 수 있다. 본 연구에서는 가상 층간 구조 페리다이나믹 해석의 파동 전파 특성을 분석한다. 층간 구조는 인접한 적층판들을 접합하는 역할뿐만 아니라 적층판 사이의 에너지 전달 특성에도 영향을 주기 때문에 적층구조물의 변형 및 운동에도 중요한 역할을 하는 것을 확인하였다. 또한 경계 근처에서 페리다이나믹 절점은 불완전한 형태의 비국부 영역을 구성하는데, 이를 통해 완전한 비국부 영역을 구성하는 내부 절점과 경계 근처의 절점에서 재료 물성치 효과가 달라지게 된다. 본 연구에서는 이와 같은 표면 효과를 보정하기 위해 비국부 체적 기반의 보정법을 도입하고, 표면 효과 보정이 다중적층 구조물의 파동 전파에 미치는 영향을 조사한다.

선박의 고속, 대형화 및 규제강화의 추세에 따라 유동소음의 중요성이 강조되고 있다. 그러나 항공, 철도 등의 공력소음 분야에서 유동소음을 설계에 반영하고 있는 것에 반해 조선해양분야에서는 고려되지 않고 있다. 본 연구에서는, 선체유기 유동소음의 해석절차를 정립하고 쇄파의 영향이 작고 선체선형에 의한 유기소음의 특성이 뚜렷한 파랑관통형 선형에 대해 소음특성을 분석하였다. 선체유기 유동소음의 주요 메커니즘인 난류경계층 내부의 복잡한 난류유동과 구조물의 유체-구조 연성적 소음원은 벽면변동압력을 이용하여 가진력을 모델링하고 파워흐름해석법을 이용하여 진동음향 응답해석을 수행하였다. 주파수 영역 및 선체부위에 따라 상의한 소음특성을 가지며 저주파수 영역에서 선형의 영향이 상대적으로 크고 유속에 비례하는 경향을 확인할 수 있었다.

In this paper, we study the effect of cooling dehumidification process and wave heat exchanger on the reduction of white smoke and the efficiency by combination of heat exchanger with numerical analysis method. For this purpose, four types of heat exchange systems combined with 5-stage wave heat exchangers were selected to analyze the heat transfer characteristics of the heat exchange system in the winter condition. As the high temperature exhaust air flowed from HX 1 to HX 5, the final outlet temperatures of the four heat exchange systems(Cases 1, 2, 3 and 4) gradually decreased. The heat transfer rate and dehumidification amount were the best in Case 1 and Case 3, respectively. It can be seen that the heat flow in the heat exchanger is different according to the combination of the four kinds of wave heat exchanger and the fluid flow.

In this study, the heat transfer characteristics of pilot wave heat exchanger for white smoke reduction system was investigated. The performance of the wave and honeycomb heat exchanger combined with the first stage, second stage and third stage was tested using a calorimeter. Air and water inlet/outlet temperature and flow rate, pressure drop and dehumidification amount were measured to compare the heat transfer performance according to the type and the combination of heat exchanger. The heat transfer rate and dehumidification amount of the wave heat exchanger were higher than that of the honeycomb heat exchanger, and the pressure drop was low. As the stage increased, the heat transfer rate and the increase of the dehumidification amount were more pronounced, and the pressure drop linearly increased. The wave heat exchanger had a lower flow resistance than the honeycomb heat exchanger with the honeycomb structure and had a higher heat transfer effect due to the convection, so the water outlet temperature was higher in the wave heat exchanger.

In this study, the heat flow characteristics of wave heat exchanger was investigated by being applied to the white smoke reduction system. Through numerical analysis, the heat transfer and flow characteristics of the wave heat exchanger with the change of inlet condition of air-side and water-side were analyzed. To investigate the temperature, the absolute humidity, heat transfer rate, pressure drop and turbulence characteristics of the wave heat exchanger, the simulation analysis was conducted by using the commercial computational fluid dynamics software (Solidworks Flow Simulation) under uniform flow conditions. As the inflow rate of air decreased and the inflow temperature of water increased, the heat transfer coefficient of the wave heat exchanger decreased. When the experimental conditions of water-side were the same, the air outlet temperature and absolute humidity of the wave heat exchanger increased with increasing inflow rate of air. To reduce the white smoke, the air outlet temperature and absolute humidity of the wave heat exchanger must be reduced. Therefore, the lower the air velocity and the water inflow temperature into the wave heat exchanger, the more effective it is.

In this study, we conducted an empirical analysis using structural equation modeling (SEM) by distributing questionnaires to 208 Chinese tourists who constitute the largest proportion of foreign tourists visiting South Korea. The survey was conducted in a face to face (FTF) manner with the aim to contribute to globalization of Korean cuisine through comprehensive analysis of the effects of preference characteristics of Korean wave dramas on the relationship among images, attitudes, and purchase intentions for Korean cuisine. The main actor characteristics among the preference characteristics of Korean wave dramas had a significant effect on the attitudes and purchase intentions for Korean cuisine. However, the thematic characteristics among the preference characteristics of Korean wave dramas did not have a significant effect on the purchase intentions for Korean cuisine; in addition, the production characteristics did not have a significant effect on the attitudes and purchase intentions for Korean cuisine. The eco-friendly and health images of Korean cuisine had a significant effect on the purchase intentions for Korean cuisine, and the attitudes toward Korean cuisine significantly affected the purchase intentions for Korean cuisine. Based on the results of this study, it is considered necessary to continuously publicize Korean cuisine through Korean wave dramas to build positive attitudes toward Korean cuisine through enhanced images of Korean cuisine.

This study presents the behavioral characteristics of submerged floating tunnels under harsh environmental conditions. To evaluate the dynamic characteristics of the submerged floating tube moored by tethers, hydrodynamic analysis was performed in time-domain. To consider the irregular wave loading condition, JONSWAP wave spectrum was used with specific significant wave height and peak period. For applying the irregular wave in the explicit dynamic analysis procedure, equivalent regular wave components which have same wave energy were applied to the external force term with random phases. According to this study, lateral and vertical motion can be effectively controlled by adjusting initial tether angle and draft. Evaluation of fatigue damage of mooring lines can be conducted by analyzing the dynamic structural stresses with appropriate S-N curves and stress concentration factors. This study also dealt with short-term fatigue analysis for checking the tethers. According to this study, cumulative fatigue damage of the tethers is definitely affected by the essential design factors such as design draft of the tunnel and tether arrangement.

실제 국내에서 관측된 가속도를 이용한 스펙트럼 값이 내진설계기준보다 상대적으로 크게 나타나는 경향을 보 이며, 특히 고진동수 구간에서 국내 내진설계 기준이 국내 고유의 지반증폭 특성을 제대로 반영하지 못하고 있어 문제 점이 많다고 지적되어 왔다. 지반증폭 특성을 분석할 때 여러 가지 방법이 제시되어 왔으며 본 연구는 현장에서 자주 적용되고 있는 지반진동의 수평/수직 스펙트럼 비율을 이용하는 방법을 적용하였다. 이 방법은 S파 및 레일리파를 이용 하는 것으로부터 출발하였으나, 최근 Coda파 및 배경잡음 등에 확대 적용되어 지반의 동적인 증폭특성 연구에 많이 이용되고 있다. 제한된 연구 기간 동안 4개 변전소시설 관측소 각각 2개 지점(노두 및 시추공)에서 운영되었고 본 연구는 4개 관측소의 노두에서 동시에 관측된 3개 중규모 지진의 가속도 지반진동(S파, Coda파 및 배경잡음)을 이용하여 지반 증폭을 분석하였다. 분석결과는 4개 관측소 각각에 대해 기존 연구결과인 시추공 지반증폭 특성과 상호 비교하였다. 또 한 각각 관측소 및 지점에서 지반의 우월진동수를 이용하여 각각 지반에 대한 등급분류도 시도하였다. 각각의 지진관측 소마다 저진동수 및 고진동수 특성, 관측소 고유의 우월진동수가 서로 상이하여 관측소 고유의 증폭특성을 보여주었다. 대다수 관측소는 S파, Coda파 및 배경잡음 에너지를 분석한 결과와 많은 부분이 유사함을 보여 주었다. 물론 본 연구 로부터 도출된 결과를 다른 방법에 적용하여 얻어진 결과와 비교한다면 지반의 동적 특성 및 지반분류 연구에 많은 정 보를 제시할 수 있다고 판단된다.

지반진동은 지진원, 지각감쇠 및 지반의 증폭특성 등 3가지 주요 인자로 구성되어 있다. 이 중 지반 증폭특성은 지진원 및 지각감쇠를 신뢰성 있게 평가하기 위해 반드시 고려하여야 한다. 본 연구의 목적은 수평/수직(H/V) 스펙트럼 비를 이용하여 각 관측소의 지반증폭 특성을 평가하는 것이다. 주파수 영역에서 H/V 스펙트럼 비를 구하는 방법은 Nakamura(1989)에 의해 처음으로 제시되었으며, 초기에는 상시미동의 표면파 특성을 이해하기 위해 사용되어 왔다. 최 근에 와서 강진동의 전단파 에너지 등으로 확장되면서 지반 증폭특성 연구에 많이 이용되고 있다. 본 연구는 예당저수 지 인근에 4개의 관측소에서 관측된 6개의 가속도 지반진동을 이용하여 H/V 스펙트럼 비를 분석하였고 각 지반진동의 S파, Coda파 및 배경잡음 각각으로부터 분석된 지반증폭 특성을 상호 비교하였다. 분석결과, 4개 관측소는 각각의 우월 주파수 대역(YDS: ~11 Hz, YDU: ~4 Hz, YDD: ~7 Hz)에서 관측소 고유의 증폭특성을 보여준다. 본 연구의 도출 결과 와 다른 방법을 통해 구한 결과의 비교 평가는 국내 지반의 동적특성 및 지반분류 연구에 유익한 정보가 될 것으로 판 단된다.