PURPOSES : There has been increasing interest in South Korea on warm-mix asphalt (WMA) and cold-mix asphalt (CMA) technologies that allow production of asphalt pavement mixtures at comparatively lower temperatures than those of hot-mix asphalt (HMA) for use in pavement engineering. This study aims to evaluate the feasibility of replacing HMA pavement with WMA pavement with the goal of reducing CO2 emissions associated with asphalt production for road construction. METHODS : Changes in the dynamic modulus characteristics of WMA and HMA according to short-term and long-term aging were evaluated. In addition, the effects of water damage were evaluated for short- and long-term aging stages. RESULTS : For WMA, in the process of mixing and short-term aging, early-age dynamic modulus decreased owing to low temperature and reduced short-term aging (STA) time. This could result in early damage to the asphalt pavement depending on the applied traffic load and environmental load. CONCLUSIONS : Mastercurves of the dynamic modulus were used for comparative analysis of WMA and HMA. Compared to the dynamic modulus after STA of HMA, the estimated aging time determined by experiments for WMA to achieve the required stiffness was more than 48 hours, which is equiva-lent to approximately 4 to 5 years real service life when converted. It is considered that further studies are needed for performance optimization to achieve early-age performance of the asphalt mixes.

PURPOSES : The purpose of this study is to provide basic data to improve the service life of asphalt pavement using basalt aggregate in Jeju Island by evaluating the performance of asphalt pavement through analysis of material and structural aspects. METHODS : To evaluate the performance of Jeju Island's asphalt pavement, cracks, permanent deformation, and longitudinal roughness were analyzed for the Aejo-ro road, which has high traffic and frequent premature damage. Cores were collected from Aejo-ro sections in good condition and damaged condition, and the physical properties of each layer were compared and analyzed. In addition, plate cores were collected from two sections with severe damage and the cause of pavement damage was analyzed in detail. RESULTS : About 45% of the collected cores suffered damage such as layer separation and damage to the lower layer. The asphalt content of surface layer in the damaged section was found to be 1.1% lower on average than that in the good condition section, and the mix gradations generally satisfied the standards. The density difference between the cores of each layer was found to be quite large, and the air voids was found to be at a high level. CONCLUSIONS : Test results on the cores showed that, considering the high absorption ratio of basalt aggregate, the asphalt content was generally low, and the high air voids of the pavement was believed to have had a significant impact on damage. High air voids in asphalt pavement can be caused by poor mixture itself, poor construction management, or a combination of the two factors. Additionally, the separation of each layer is believed to be the cause of premature failure of asphalt pavement.

PURPOSES : This study intended to derive a methodology that can evaluate water splash caused by distress on the road surface based on experimental methods and to present quantitatively by analyzing the impact on road users. METHODS : Through literature review, the current problems of road pavement and drainage facility standards, the factors of road splash caused by puddle was selected to measure damage. Field measurements were conducted by setting different conditions for each factors and setting different conditions based on the hypothesis. In addition, water splash by surface distress type and puddle was measured to analyze using statistical techniques from correlation to multi-regression. RESULTS : The maximum and effective distance due to road splash increases as the driving speed, regardless of vehicle load and tyre type. Splash was measured according to the type of road distress to analyze the correlation between the influencing factors, and there was a weak correlation between the width and length of the puddle, depth and the effective distance. In addition, the interaction analysis showed that there was an interaction between the width of the water hole and the depth of puddle. Moreover, based on the multi-regression analysis, it was not statistical significant. This is judged to that the number of data samples used for this analysis is limited because the diversity of puddle conditions cannot be set differently for each type of distress. CONCLUSIONS : Since the distress of depending on the size, depth and shape of the road surface, it is necessary to calculate it and present maintenance standards, so this results present an experimental methodology that can intuitively evaluate damage cased by unestablished puddle. From this results, this is expected to be used as a quantitative indicator to evaluate the satisfaction of road users as a functional performance according to road surface condition.

In this paper, seismic performance evaluation was carried out for eight circular reinforced concrete columns designed seismically by KRTA[1]and KCI[8]. Primary design parameters for such columns included many longitudinal reinforcements, yield strength of reinforcements, the vertical spacing of spirals, aspect ratio, and axial force ratio. The test results showed that all the columns exhibited stable hysteretic and inelastic responses. Based on the test results, drift ratios corresponding to each damage state, such as initial yielding, initial cover spalling, initial core concrete crushing, buckling, and fracture of longitudinal reinforcement and final spalled region, were evaluated. Then, those ratios were compared with widely accepted damage limit states. The comparison revealed that the existing damage states were considerably conservative. This implies that additional research is required for the damage limit states of such columns designed seismically by current Korean design codes.

본 연구에서는 하수 재이용을 위한 역삼투막 공정에서 전처리 정밀여과막(MF) 손상에 대한 누출되는 다양한 수 질변화로써 막 손상 검지 방안을 제시하였다. 이를 위하여 역삼투막 유입수질 적합성 평가지표인 SDI (silt density index)를 3에서 5의 범위 내에서 막 손상 시 검지 감도를 정량화하기 위하여 전처리 분리막이 1에서 3가닥 파단에 따라 SDI는 1.92에 서 6.11까지 증가한 결과를 확인할 수 있었다. 일반적으로 3을 기준으로 역삼투막 유입수질로 설정하였을 때 분리막이 3가닥 까지 파단이 되어야만 막 손상 검지가 가능하다는 것을 의미하며 역삼투막의 오염은 잠재적으로 가속화되어 효율을 저하시 킬 수 있다. 또한 이때 누출되는 입자성과 유기물질에 대하여 0.45 μm 이상의 크기만 걸러주는 입자계수는 입도분포별 막 파 단 개수에 따라 일정한 패턴을 확인할 수 없었으며, TOC 농도는 약 2배의 변화패턴으로써 SDI와의 상관관계로써 TOC가 막 손상 수질지표로써 신뢰성이 높은 것으로 확인되었다. 수질분석결과와 더불어 USEPA에서 제시하는 막 손상 검지 방법 중 압력손실시험과 이를 기반으로 LRVDIT 모델의 적합성 평가를 한 결과 막 손상 또는 역삼투막 공정으로 유입되는 막오염물질 을 신속하게 확인할 수 있는 SDI 및 TOC를 포함한 LRVDIT 모니터링과 UCL 설정을 병행해야 한다.

This study introduces a newly developed PC non-bearing wall system to prevent the damage of RC wall-type apartments that have been heavily damaged by the 2017 Pohang Earthquake. In order to evaluate the performance of the developed PC non-bearing wall system, a static cyclic test is conducted. The prototype of test specimen is from the RC wall-type apartment which has been severely damaged by the 2017 Pohang Earthquake. The specimen with the conventional non-bearing wall system showed the similar damage of RC wall type apartment suffered from the Pohang Earthquake. In case of the specimen with the developed PC non-bearing wall system, cracks and damages were not transmitted between the walls due to the seismic slit and there were almost no cracks in the non-bearing walls. Therefore, the proposed non-bearing wall system, separated from the structural walls, could prevent spreading cracks to bearing walls and make it possible to effectively control damage due to earthquake loads.

PURPOSES: Spalling is one of the primary problems that lead to the damage of concrete pavements. The purpose of the study is to analyze the impact range of spalling that occurred in an area of concrete pavement by applying a variety of nondestructive and destructive testing methods. METHODS: Spalling of the concrete pavement was categorized into four different sizes, 0 cm, 7.5 cm, 15 cm, and 30 cm. Nondestructive and destructive tests were performed at the point of spalling and 1 m away, respectively, and the obtained results were compared. The nondestructive tests included the electrical resistance test and the ultrasonic velocity test as well as strength tests by Schmidt hammer and concrete tester. The destructive tests included the direct compressive strength test and the chloride content test using field cored specimens. The test results helped in the analysis of the correlation between the current spalling damage condition and the expected damage acceleration. RESULTS: Based on the present study, the repair area and depth of spalling for a partial depth repair was suggested. It was also shown that the size of the spalling is highly correlated with the chloride content and the electrical resistance of the concrete pavement. CONCLUSIONS: The degree of spalling deterioration was found to be highly correlated with the chloride content and electrical resistance of the concrete pavement and based on the results, the extent of repair could be determined more quantitatively.

PURPOSES: This study was conducted to investigate the causes of damage and to suggest proper repair methods for the sections in which a number of transverse cracks and faulting occurred in JCP (Jointed Concrete Pavement) slabs during the early-age performance period. METHODS: Field crack survey, FWD (Falling Weight Deflectometer) investigation, dowel bar installation condition survey, longitudinal profile survey, and in-situ core specimen inspection were conducted. . RESULTS : As a result of the analysis, it was found that there was no decline in the composite modulus of the subgrade reaction (k-value). The dowel bars were properly installed, but the LTE (Load Transfer Efficiency) of the joint and transverse cracks were analyzed to be very low. In addition, it was found that there are voids in the bottom of the slab at the joints and corners. Due to the excessive built-in curling in the early age of concrete pavement construction, upward curling displacement occurred at the joints and corners, resulting in voids at the bottom of the slab. As a result, it was found that transverse cracks occurred due to the defective joint LTE. CONCLUSIONS: Excessive built-in curling can cause early age cracks in the JCP slabs. In order to minimize the occurrence of reflection cracks after the application of the asphalt overlay in the future, concepts of alternative repair methods were proposed.

The purpose of this study is to evaluate the structural safety of cultural altar since its bearing capacity has been questioned due to weathering damages and sectional defections. This evaluation process consists two stages; which the first is field investigation and the second is structural modeling and analysis. Based on field investigation, all of the structural members supporting the altar were carefully examined and all the findings were accounted for the development of the structural modeling using the Midas computer program. Using a 3D scanner, the weight of the Buddha statue was applied to the structural modeling. Then, according to the allowable stress design method of KBC2016, the structural safety was evaluated. Based on this result, replacements of several structural members were recommended to increase the structural safety and value of cultural property.

Among the 8,700 in-service bridges in national highway, the steel bridges cover the 1600 sites and make up approximately the 20 percentage of the total amounts. Due to recent rapid increase both in traffic volume and in frequency of overloaded vehicles, the need for re-evaluating the fatigue life of the steel bridges is increasing. However, the existing fatigue life assessment method are too complicate and difficult to apply to field directly. To improve such deficiency of the existing fatigue life assessment procedures, this study reviews the fatigue life assessment methods in Eurocode and then proposes an easier and simpler fatigue life assessment procedure that could evaluate the remaining fatigue life of the steel bridges using traffic data collected from a high-speed weigh-in-motion system installed in the national highway network. The Proposed fatigue life evaluation method is as follows; 1. Calculation of fatigue resistance 𝛾𝑀f and fatigue strength Δ𝜎𝑐 used in design, 2. Calculation of partial safety factor 𝛾𝐹f for equivalent stress range, 3. Calculation of stress range Δ𝜎𝐸2 using influence line, 4. Calculation of damage equivalent factor λ, 5. Review of Fatigue state and evaluation of fatigue life. The Proposed method can omit the existing complicated and repetitive calculation. Therefore, proposed method can estimate the fatigue damage and the theoretical fatigue life simply by comparing with the existing method.

In this study, the seismic performance of concrete-steel composite moment frame structures equipped with seismic retrofitting systems such as seismic reinforcement, base isolators, and bracing members, which are typical earthquake damage mitigation systems, is evaluated through nonlinear dynamic analyses. A total of five frame models were designed and each frame model was developed for numerical analyses. A total of 80 ground acceleration data were used to perform the nonlinear dynamic analysis to measure ground shear force and roof displacement, and to evaluate the behavioral performance of each frame model by measuring inter-story drift ratios. The analysis results indicate that the retrofitting device of the base isolator make a significant contribution to generating relatively larger absolute displacement than other devices due to flexibility provided to interface between ground and column base. However, the occurrence of the inter-story drift ratio, which is a relative displacement that can detect the damage of the structure, is relatively small compared with other models. On the other hand, the seismic reinforced frame model enhanced with the steel plate at the lower part of the column was found to be the least efficient.

내염소성 원생동물인 크립토스포리디움, 지아디아 등 병원성 미생물의 제거에 대한 신뢰성을 확보하기 위해 정수 처리 공정에서 막여과 시스템이 각광받고 있으며, 이러한 신뢰성을 보증하기 위해 막 완결성에 대한 연구가 중요시되고 있다. 막 완결성 시험은 크게 직접법과 간접법으로 분류되는데, 직접법 중 압력기반의 시험은 버블포인트 이론을 근간으로 병원성 미생물의 최소 크기인 3 μm 크기 이상을 감지할 수 있는 감도로 USEPA Guidance Manual에서 제시하고 있다. 간접법은 온라 인 상태에서 연속적인 운전이 가능하다는 점에서 널리 사용되지만, 직접법에 비해 현저히 낮은 막 손상 감지 감도를 가지고 있 으며, 손상 부위를 특정 지을 수 없는 한계가 있기에 이러한 감지 감도를 개선해야 할 필요가 있다. 따라서 본 연구에서는 압 력 손실 시험에 의한 막 완결성 시험을 통해 막 파단 형태별, 파단 개수, 초기설정압력값에 따른 압력손실률과 LRVDIT 신뢰 성 범위를 상호 비교함으로써 막 손상에 따른 감도의 결과를 정량화하여 UCL 기준을 나타내어 비교 평가하였다.

The result of the previous work leads to the idea that the inner area of the hyperbolic shell generator should be minimized for the cooling tower with higher first natural frequency. In this study the inner area of the hyperbolic shell generator was graphically established under varying height of the throat and angle of the base lintel. From the graph, several shell geometries were selected and analysed in the aspect of the natural frequency. Three representative towers reinforced differently due to different first natural frequencies were analysed non-linearly and evaluated using a damage indicator based on the change of natural frequencies. The results demonstrated that the damage behaviour of the tower reinforced higher due to a lower first natural frequency was not necessarily advantageous than the others

The cryopreservation of sperm has become the subject of research for successful artificial insemination technologies. Antifreeze proteins (AFPs), one of the factors necessary for effective cryopreservation, are derived from certain Antarctic organisms. These proteins decrease the freezing point of water within these organisms to below the temperature of the surrounding seawater to protect the organism from cold shock. Accordingly, a recent study found that AFPs can increase the motility and viability of spermatozoa during cryopreservation.To evaluate this relationship, we performed cryopreservation of boar sperm with AFPs produced in the Arctic yeast Leucosporidium sp. AFP expression system at four concentrations (0, 0.01, 0.1, and 1 μg/ml) and evaluated motility using computer assisted sperm analysis. DNA damage to boar spermatozoa was measured by the comet assay, and sperm membrane integrity and acrosome integrity were evaluated by flow cytometry. The results showed that motility was positively affected by the addition of AFP at each concentration except 1 μg/ml (p<0.001).Although cryopreservation with AFP decreased the viability of the boar sperm using, the tail DNA analyses showed that there was no significant difference between the control and the addition of 0.1 or 0.01 μg/ml AFP. In addition, the percentage of live sperm with intact acrosomes showed the least significant difference between the control and 0.1 μg/ml AFP (p<0.05), but increased with 1 μg/ml AFP (p<0.001). Our results indicate that the addition of AFP during boar sperm cryopreservation can improve viability and acrosome integrity after thawing.

Determining of the shape in the process of design for natural draught cooling tower is very important, because the shape of hyperbolic shell is respond sensitively to dynamic behavior of the whole cooling tower against wind load. In engineering practice, the geometric parameters have been determining based on the natural frequency. This study analyses influence of the tower shell geometric parameters on the structural behavior. For three representative models were selected, they were analyzed based on evaluation of damage by means of nonlinear FE-method. As a result, a hyperbolic rotational shell with the small radius overall was the lowest damage index induced by sufficient capacity of the stress redistribution and thus a wind-insensitive structure.

교량의 교각 설계시에는 설계기준에 의거하여 차량의 충돌에 대비한 적절한 방호시설 등이 고려되고 있으나, 지하차도의 기둥 설계시에는 차량의 충돌과 관련된 규정이 없다. 또한 지하차도의 기둥은 상대적으로 폭이나 두께가 작아서 차량의 충돌에 의하여 큰 손상이 발생할 수 있다. 본 논문에서는 지하차도 기둥에 대한 충돌해석을 통하여 차량의 충돌에 의한 구조물의 손상을 평가하였다. 충돌해석에서는 지하차도 기둥의 물성과 형태 그리고 차량의 속도와 종류 등이 매개변수로 고려되었다. 수치해석 결과 지하차도 기둥이 심하게 손상되는 경우가 있었으며 따라서 지하차도의 기둥 설계시에는 차량 충돌에 대한 적절한 고려가 필요하다.

The deep see riser is often exposed to harsh ocean environment which may cause riser failure. If the riser fails, it may cause serious economical losses as well as environmental problems. Thus, monitoring the integrity of the rider for preventing sudden failure is very important. In this study, the structural behavior monitoring systems installed for the deep sea riser are examined, and, using the estimated behavior, the applicability of the structural integrity evaluation methods is examined via numerical analysis.

The purpose of this study is to improve the previous damage evaluation model for RC members which is proposed by Igarashi[1] in 2010.The previous model was not confirmed by enough data of damage such as, residual crack length, width and area for exfoliation of concrete, etc. In addition, validation of the model is still insufficient. Therefore, experiment of a real-scale RC structure and experiment of RC columns using the high-strength concrete were conducted to gather the data of damage in RC members. The investigation has been conducted gathering the data not only additional experiments data but also existing data for modification of damage evaluation model. It has been investigated on changing damage in RC due to axial force ratio, shear reinforcement and shear span ratio. As a result, several problems were founded in the previous model, such as, hinge length(lp), spacing of flexural crack(Sav,f), total width of flexural cracks regulated by maximum width of flexural crack(nf) and total width of shear cracks regulated by maximum width of shear crack(ns). New model is proposed and evaluated the damage properly.