지표면의 불투수층 증가는 빗물의 토양침투를 감소시키고 우수 침투를 제한하여 표면 유출에 의한 피해를 야기하였으며, 홍수 도달시간이 단축됨에 따라 첨두 유출량이 증가하므로 배수 시스템의 용량 부족 및 침수 피해를 초래하였다. 이에, 환 경부에서는 생태면적률 제도를 도입하여 저영향 개발(Low Impact Development, LID) 기술 도입의 활성화를 도모하고 있 으며, 이 중 투수블록포장이 약 40%를 차지하고 있다. 그러나, 주로 표층 콘크리트 블록의 품질기준 마련 및 성능 개선 연 구가 수행되었으며, 하부구조의 우수 침투 능력을 평가한 연구는 미흡한 실정이다. 특히, 투수성능이 증가할수록 구조적 지 지력이 감소하므로 내구성을 만족하는 범위에서 투수계수를 충족하는 입도분포를 실험적 연구를 통해 제시할 필요가 있다. 따라서, 시험체 내 수두를 일정하게 유지시켜 일정 시간동안 유입되는 하부 유출량을 측정하였으며, 같은 입도분포일 때 잔 골재 함량이 증가할수록 투수계수가 감소하는 것으로 나타났다. 이처럼 골재 입도분포 특성에 의해 물이 하부로 침투되는 유출량이 상이하므로 정량적인 평가를 통해 투수계수를 만족하는 적정 입도 기준의 제시가 가능할 것으로 판단된다.

본 연구는 일반홍삼(70 °Brix)과 발효홍삼(45 °Brix)에 대한 항산화 성분 분석 및 항산화 효능 측정을 위한 적정 분석시료 함량을 설정하고, 홍삼의 발효에 따른 항산화성의 변화를 조사하였다. 홍삼의 flavonoid 및 phenolics 함량 측정은 일반홍삼과 발효홍삼 각각 농축액 시료 3 g을 증류수로 100배 희석하여 측정용 시료 1 mL 당 홍삼농축액 20-30 mg을 사용하는 것이 시료 채취와 낮은 흡광도에 의한 오차도 줄일 수 있었다. 홍삼의 항산화성 측정으로 홍삼 시료 mg 당 DPPH에 대한 전자공여능 및 ABTS radical 소거능은 일반홍삼과 발효홍삼 모두 농축액 분석시료 20-30 mg/mL에서 가장 안정적이었다. 세포에서의 항산화 효능으 로 ROS의 소거능은 일반홍삼과 발효홍삼 모두 농축액 분석시료 20 mg/mL 전후에서 ROS radical 소거능의 차이가 가장 컸으며 분석에 적합한 농도였다. Flavonoid 함량과 ROS radical 소거능은 발효홍삼 농축액이 일반홍삼 농축액보다 더 높았으나, radical 소거능은 유사하였다. 같은 농도의 일반홍삼과 발효홍삼을 비교할 경우 발효홍삼이 일반홍삼보다 항산화 효과가 더 높았다. 일반홍삼 및 발효홍삼의 항산화성 물질의 정량 및 그 항산화 효능을 측정하기 위해서는 농축액의 농도 차이에도 불구하고 일반홍삼과 발효홍삼 각각 농축액 2-3 g을 채취하여 100배 희석하여 분석 시료로 사용하는 것이 적합하였다.

Solar energy has been recognized as an alternative energy source that can help address fuel depletion and climate change issues. As a renewable energy alternative to fossil fuels, it is an eco-friendly and unlimited energy source. Among solar cells, thin film Cu2ZnSn(S,Se)4 (CZTSSe) is currently being actively studied as an alternative to heavily commercialized Cu (In,Ga)Se2 (CIGS) thin film solar cells, which rely upon costly and scarce indium and gallium. Currently, the highest efficiency achieved by CZTSSe cells is 14.9 %, lower than the CIGS record of 23.35 %. When applied to devices, CZTSSe thin films perform poorly compared to other materials due to problems including lattice defects, conduction band offset, secondary phase information, and narrow stable phase regions, so improving their performance is essential. Research into ways of improving performance by doping with Germanium and Cadmium is underway. Specifically, Ge can be doped into CZTSSe, replacing Sn to reduce pinholes and bulk recombination. Additionally, partially replacing Zn with Cd can facilitate grain growth and suppress secondary phase formation. In this study, we analyzed the device’s performance after doping Ge into CZTSSe thin film using evaporation, and doping Cd using chemical bath deposition. The Ge doped thin film showed a larger bandgap than the undoped reference thin film, achieving the highest Voc of 494 mV in the device. The Cd doped thin film showed a smaller bandgap than the undoped reference thin film, with the highest Jsc of 36.9 mA/cm2. As a result, the thin film solar cells achieved a power conversion efficiency of 10.84 %, representing a 20 % improvement in power conversion efficiency compared to the undoped reference device.

In this investigation, samples of the chemical (Hg1-xPbxBa2Ca1.8Mg0.2Cu3O8+δ) were prepared utilizing a solid-state reaction technique with a range of lead concentrations (x = 0.0, 0.05, 0.10, and 0.20). Specimens were pressed at 8 tons per square centimeter and then prepared at 1,138 K in the furnace. The crystalline structure and surface topography of all samples were examined using X-ray diffraction (XRD) and atomic force microscopy (AFM). X-ray diffraction results showed that all of the prepared samples had a tetragonal crystal structure. Also, the results showed that when lead was partially replaced with mercury, an increase in the lead value impacted the phase ratio, and lattice parameter values. The AFM results likewise showed excellent crystalline consistency and remarkable homogeneity during processing. The electrical resistivity was calculated as a function of temperature, and the results showed that all samples had a contagious behavior, as the resistivity decreased with decreasing temperature. The critical temperature was calculated and found to change, from 102, 96, 107, and 119 K, when increasing the lead values in the samples from 0.0 to 0.05, 0.10, and 0.20, respectively.

본 논문에서는 시멘트에 탄소나노튜브를 혼입하여 전기 전도성을 향상시킨 복합재료의 압저항 특성을 딥러닝 기반 트랜스포머 알 고리즘을 적용하여 분석하였다. 훈련 데이터 확보를 위한 실험수행을 병행하였으며, 기존 연구문헌을 참조하여 배합설정, 시편제작, 화학조성 분석, 압저항 성능측정 실험을 수행하였다. 특히 본 연구에서는 탄소나노튜브 혼입 시편뿐 아니라 플라이애시를 바인더 대 비 50% 대체한 시편에 대한 제작 및 성능평가를 함께 수행하여, 전도성 시멘트 복합재료의 압저항 특성 향상 가능성을 탐구하였다. 실 험결과, 플라이애시 대체 바인더의 경우 보다 안정적인 압저항 특성결과가 관찰되었으며, 측정된 데이터의 80%를 이용하여 트랜스 포머 모델을 훈련시키고 나머지 20%를 통해 검증하였다. 해석 결과는 실험적 측정과 대체로 부합하였으며, 평균 절대 오차 및 평균 제 곱근 오차는 각각 0.069~0.074와 0.124~0.132을 나타내었다.

In this study, the elastic properties of aluminium nanocomposite representative volumetric element (RVE) reinforced with GNP have been analysed. Pure aluminium is lightweight and has low strength which is not suitable for various aerospace applications. Adding graphene to aluminium gives a highly strengthened nano-matrix. A 3D multiscale finite element (FE) representative volumetric element (RVE) has been developed to estimate the mechanical behaviour of GNP-reinforced aluminium graphene nanocomposite (AGNC). The factors influencing the behaviour of AGNC have been investigated with different weight fractions (wt%), sizes and orientations of GNP. The Young’s modulus of AGNC is enhanced by increasing the wt% of GNP and reducing the size of GNP in the aluminium matrix. The Young’s modulus of AGNC with 1% wt% has been enhanced two times and yield strength by five times than pure Al matrix. In the case of different sizes of GNP, the strength of 15-nm-diameter GNP AGNC enhanced two times and medium-sized GNP, i.e. 30 nm has shown a great combination of strength and ductility. After that different orientations have also influenced the mechanical properties and enhancement shown in layered orientation compared to different angles of GNP.

The study used the whole-life carbon assessment method to conduct a thorough carbon-neutral evaluation of a standard steel structure. To further assess carbon emissions, 11 design-changed models were evaluated, with changes made to the span between beams and columns. The results of the carbon emission assessment showed savings of approximately 13.1% by implementing the stage of the beyond life cycle. Additionally, the evaluation of carbon emissions through design changes revealed a difference of up to 42.2%. These findings confirmed that recycling and structural design changes can significantly reduce carbon emissions by up to 48.6%, making it an effective means of achieving carbon neutrality. It is therefore necessary to apply the stage of beyond life cycle and structural change to reduce carbon emissions.

Epoxy-based composites find extensive application in electronic packaging due to their excellent processability and insulation properties. However, conventional epoxy-based polymers exhibit limitations in terms of thermal properties and insulation performance. In this study, we develop epoxy-based siloxane/silica composites that enhance the thermal, mechanical, and insulating properties of epoxy resins. This is achieved by employing a sol–gelsynthesized siloxane hybrid and spherical fused silica particles. Herein, we fabricate two types of epoxy-based siloxane/ silica composites with different siloxane molecular structures (branched and linear siloxane networks) and investigate the changes in their properties for different compositions (with or without silica particles) and siloxane structures. The presence of a branched siloxane structure results in hardness and low insulating properties, while a linear siloxane structure yields softness and highly insulating properties. Both types of epoxy-based siloxane/silica composites exhibit high thermal stability and low thermal expansion. These properties are considerably improved by incorporating silica particles. We expect that our developed epoxy-based composites to hold significant potential as advanced electronic packaging materials, offering high-performance and robustness.

Metal additive manufacturing (AM) has transformed conventional manufacturing processes by offering unprecedented opportunities for design innovation, reduced lead times, and cost-effective production. Aluminum alloy, a material used in metal 3D printing, is a representative lightweight structural material known for its high specific strength and corrosion resistance. Consequently, there is an increasing demand for 3D printed aluminum alloy components across industries, including aerospace, transportation, and consumer goods. To meet this demand, research on alloys and process conditions that satisfy the specific requirement of each industry is necessary. However, 3D printing processes exhibit different behaviors of alloy elements owing to rapid thermal dynamics, making it challenging to predict the microstructure and properties. In this study, we gathered published data on the relationship between alloy composition, processing conditions, and properties. Furthermore, we conducted a sensitivity analysis on the effects of the process variables on the density and hardness of aluminum alloys used in additive manufacturing.

The physical and antibacterial properties of ophthalmic lenses fabricated by copolymerization with hydrogel monomers using two types of graphene were measured, and their usability as contact lens materials was analyzed. For polymerization, silicone monomers, including SID-OH, 3-(methacryloxy)propyl tris(trimethylsiloxy)silane, and decamethylcyclopentasiloxane, were used, and N,N-dimethylacetamide, ethylene glycol dimethacrylate as a crosslinking agent, and azobisisobutyronitrile as an initiator were added. Also, graphene oxide nanoparticle (GON) and graphene nanoplate (GNP) were used as an additive, and the physical properties of the lenses fabricated after copolymerization were evaluated. The fabricated lenses satisfied the basic physical properties of general hydrogel contact lenses and showed the characteristics of lenses with high water content, and the disadvantage of very weak durability, due to low tensile strength. However, it was confirmed that the tensile strength and antibacterial properties were greatly improved by adding GON and GNP. With GON, the oxygen permeability and refractive index of the fabricated lenses were slightly improved. Therefore, it was determined that the graphene materials used in this study can be used in various ways as a contact lens material.

대표적인 짚공예 가운데 하나인 맥간공예(혹은 보릿대 조각공예)는 표면이 매끄럽고 광택이 나는 보릿대를 활용하고 있으며 최근에 국내뿐 아니라 해외로 전파되고 있다. 보릿대 표면의 줄기 방향과 나란한 미세 줄무늬는 맥간공예 작품에 입체감과 각도에 따른 색감을 갖게 한다. 하지만 아직까지 보릿대 표면의 형상과 물성이 체계적으로 분석되지 않은 실정이다. 본 연구에서는 고해상도 실체현미경과 고해상도 3차원 X-ray 현미경을 이용하여 보릿대의 미세구조를 이미징할 뿐만 아니라 보릿대의 물접촉각과 인장 강도를 측정하여 보릿대의 재질을 분석하였다. 이를 통해 보릿대 최외각에 존재하는 4-6 μm 너비의 미세요철에 의한 줄무늬, 소수성을 띈 겉면, 친수성을 띈 속면, 그리고 60 MPa 정도의 줄기 방향의 항복강도를 갖는 보릿대 특성을 확인하였다. 본 연구에서 제시한 분석 방법으로 볏짚을 비롯한 다른 짚공예에 사용되는 짚 재료의 특성을 파악한다면 짚의 재질을 최대로 활용한 새로운 짚공예로 이어질 것이다.

본 연구는 생분해성 용기 개발의 연구성이 대두됨에 따 라서 동물성 재료로 제조한 생분해성 용기의 개발의 목적에 있다. 연구 결과 돈피, 우피, 닭피에 있어서 돈피가 우수한 수율과 단백질 분자량을 가진 것으로 나타났다. 이에 돈피를 이용하여 생분해 용기를 개발하였으며, 단면적 확인 결과 호두 껍질 분말 10%를 첨가한 처리구에서 적은 공극을 보였으며, 호두 껍질 분말 20%를 첨가한 처리구에서 공극의 크기가 큰 것을 확인할 수 있었다. 물성 연구 결과 호두 껍질 분말 10% 처리구가 더 높은 경도를 나타 내었으며, 호두 껍질 분말 20% 처리구가 더 높은 탄력성을 나타내었다. 압축강도는 호두 껍질 분말 20% 처리구가 더 높은 값을 나타내었다. General bacteria, E. coli 연구 결과 모든 일자에서 불검출되어 미생물로부터의 안정성은 더 장기간으로 실험해볼 필요가 있을 것으로 보인다. 또한 높은 항균 능력과 생분해능의 결과를 보여 저장 기간의 안정성이 높은 용기의 개발과 환경의 영향을 최소화 할 수 있을 것으로 판단된다. 따라서 돈피 젤라틴에 난각과 호두 껍질 분말을 넣어 제조한 생분해성 용기의 개발의 기초 데이터로 이용될 수 있을 것으로 생각된다.

Non-face-to-face lectures have become a necessity rather than an option since COVID-19, and in order to improve the quality of university education, it is necessary to explore the properties of non-face-to-face lectures and make active efforts to improve them. This study, focusing on this, aims to provide basic data necessary for decision-making for non-face-to-face lecture design by analyzing the relative importance and execution satisfaction of non-face-to-face lecture attributes for professors and students. Based on previous research, a questionnaire was constructed by deriving 4 factors from 1st layer and 17 from 2nd layer attributes of non-face-to-face lectures. A total of 180 valid samples were used for analysis, including 60 professors and 120 students. The importance of the non-face-to-face lecture properties was calculated by obtaining the weights for each stratified element through AHP(Analytic Hierachy Process) analysis, and performance satisfaction was calculated through statistical analysis based on the Likert 5-point scale. As a result of the AHP analysis, both the professor group and the student group had the same priority for the first tier factors, but there was a difference in the priorities between the second tier factors, so it seems necessary to discuss this. As a result of the IPA(Importance Performance Analysis) analysis, the professor group selected the level of interaction as an area to focus on, and it was confirmed that research and investment in teaching methods for smooth interaction are necessary. The student group was able to confirm that it is urgent to improve and invest in the current situation so that the system can be operated stably by selecting the system stability. This study uses AHP analysis for professors and students groups to derive relative importance and priority, and calculates the IPA matrix using IPA analysis to establish the basis for decision-making on future face-to-face and non-face-to-face lecture design and revision. It is meaningful that it was presented.

본 연구의 목적은 생체 신호 측정 압력 및 인장 직물 센서의 전극을 자수 공정을 이용하여 제작할 때 전도사의 필요 물성을 파악하는 것이다. 스마트 웨어러블 제품의 전극을 전도사를 이용한 자수 공정을 통해 전극 및 회로 등을 제작하면 불필요한 재료 손실이 없고 복잡한 전극 모양이나 회로 디자인을 컴퓨터 자수기를 이용하여 추가 공정 없이 제작할 수 있다. 하지만 보통의 전도사는 자수 공정 내의 부하를 못 이기고 사절 현상이 발생하기에 본 연구에서는 silver coated multifilament yarn 3종류의 기계적 물성인 S-S curve, 두께, 꼬임 구조 등을 분석하고 동시에 자수기의 실의 부하를 측정하여 자수 공정 내 전도사의 필요 물성을 분석하였다. 실제 샘플 제작에서 S-S curve의 측정 결과가 가장 낮은 silver coated polyamide/polyester가 아닌 silver coated multifilament의 사절이 발생하였으며 그 차이는 실의 꼬임 구조와 사절이 일어난 부분을 관찰한 결과 수직으로 반복적인 부하가 일어나는 자수 공정에서 꼬임이 풀리면서 사절이 일어나는 것을 알 수 있었다. 추가적으로 압저항 압력/인장 센서를 제작하여 생체 신호 측정용 지표인 gauge factor를 측정하였으며 스마트 웨어러블 제품의 대량 생산화에 중요한 부분인 자수 전극 제작으로의 적용 가능성을 확인하였다.

This study examined the optimal temperature and time conditions to maintain high quality Dongchimi during the fermentation and storage period. Dongchimi was fermented at low (5oC), medium (10 and 15oC), and high (20oC) temperatures until the acidity reached 0.2, 0.3, and 0.4%. respectively. From the consumer’s preference test enrolling five consumers, Dongchimi fermented at 15oC until an acidity of 0.3% (for approximately six days) was evaluated to be the optimal status because of its high score of overall acceptance, taste, and odor of consumers. To determine the optimal storage temperature of fermentation, Dongchimi was stored at three different temperatures (−1, 2, 5oC) for four weeks after fermenting at 15oC for six days. During the storage period, most of the physicochemical properties (pH, acidity, reducing sugar content, and organic acid) and microbiological properties changed significantly in the 2 and 5oC groups, resulting in a significant change in descriptive sensory analysis of Dongchimi. These results indicate that fermentation at 15oC and storage at −1oC for Dongchimi enables it to maintain the best quality for a long time.

This study was carried out to standardize the material properties of roll-over protective structure (ROPS) for agricultural tractor. The material properties which were obtained from stress-strain curve, a result of tensile test stress, were used to apply to the virtual test and varied from one production lot to the other and from one manufacturer to the other. And the finite element analysis was performed on the ROPS according to the OECD code. The results show that the load-displacement curves of virtual test were approximately equal to the actual test curves. The manufacturer or lot has been shown to have little effect on the properties of the material. Therefore, it is expected that the representative values that can be used in the finite element analysis can be determined by averaging the property values.

The purpose of this study is to analyze the factors influencing consumers purchasing of domestic, imported and craft beer through AHP analysis and to provide implications for marketing for each beer market. In this study, theories and calculations related to AHP analysis were thoroughly examined and selection attributes were determined by referring to existing theories. A total of 164 consumers who have purchased beer were the target of the survey. The results were analyzed by AHP analysis and the differences were analyzed. It was confirmed that the domestic, imported, and craft beer had the highest weight in the taste in the first layer. At this time, we can confirm that imported, and craft beer has a relatively high weight on taste and domestic beer has a relatively high weight on brand image. We also found that design and advertising images do not have a significant impact on beer selection. Even though it is study on beer, we can find people have different preference between their orgin. In this study, it is possible to show what type of factors does the beer manufacturing and distribution company should concentrate on by analyzing factors that consumers consider, unlike other studies focusing on consumption status of existing beer.

This research is carried out to analyze the effects of Styrene and PVP on the properties of silicone hydrogel lenses. Styrene group and PVP(Polyvinylpyrrolidone) are used as additives for a basic combination containing silicone monomer, TSMA(trimethylsilyl methacrylate) and DMA(n,n-dimethylacrylamide) added to the mix at ratios of 1~10 %. Silicone hydrogel lens is produced by cast-mold method. The polymerized lens sample is hydrated in a 0.9 % saline solution for 24 hours before its optical and physical characteristics are measured. Measurement of the physical characteristics of the produced material shows that the refractive index is 1.3682~1.4321, water content 77.11~45.73 %, visible light transmittance 95.14~88.20 %, and tensile strength 0.0652~0.3113 kgf. The results show a decrease of refractive index as the ratio of additives and water content decreases. The result of the stabilization test of polymerization show an increase of extractables along with increase of the ratio of additives, but the difference is not significant for all samples, so it can be judged that the stabilization of the polymer is maintained. Therefore, the additions of styrene and PVP should be taken into consideration for their effects on the physical properties of silicone hydrogel lens.