Oxide semiconductor, represented by a-IGZO, has been commercialized in the market as active layer of TFTs of display backplanes due to its various advantages over a-Si. a-IGZO can be deposited at room temperature by RF magnetron sputtering process; however, additional thermal annealing above 300oC is required to obtain good semiconducting properties and stability. These temperature are too high for common flexible substrates like PET, PEN, and PI. In this work, effects of microwave annealing time on IGZO thin film and associated thin-film transistors are demonstrated. As the microwave annealing time increases, the electrical properties of a-IGZO TFT improve to a degree similar to that during thermal annealing. Optimal microwave annealed IGZO TFT exhibits mobility, SS, Vth, and VH of 6.45 cm2/Vs, 0.17 V/dec, 1.53 V, and 0.47 V, respectively. PBS and NBS stability tests confirm that microwave annealing can effectively improve the interface between the dielectric and the active layer.

This paper reports slug bubble dynamics on modified surface with two-dimensional graphene film in downward-facing nucleate boiling. Behaviors of slug bubbles were observed with high speed camera, and post-processing was followed to measure departing speed, frequency, and diameter of slug bubbles, which were important to analyze boiling performance change. The graphene-modified surface showed enhanced boiling heat transfer coefficient (BHTC) and critical heat flux (CHF). The effect of surface modification on slug bubble dynamics was quantitatively analyzed; bigger slugs departed from the modified surface with faster speed but same frequency, compared with the bare. It seems that the BHTC enhancement is caused by increase of bubble diameter, resulting in increase of its departing speed. The higher speed of departing bubble could extend the hydrodynamic limit of vapor removal from downward-facing surface, so that CHF performance could be enhanced.

표고(Lentinula edodes), 노루궁뎅이(Hericium erinaceus), 느타리(Pleurotus ostreatus)의 버섯수확후배지(spent mushroom substrate, SMS)를 퇴비화에 활용하였다. 퇴비화 온도변화는 50oC 이상에서 7일에서 10일 동안 지속 되어 30일에 부숙이 완료되었다. 퇴비화 된 LeCSMS, HeCSMS는 130%, 80% 무종자에 대한 종자 발아지수를 보여 부숙도에 대한 종자 발아지수를 충족하였다. 퇴비화에 따른 물리 화학적 변화를 조사한 바 pH 범위가 4-5 에서 6-7로 증가 되었고 EC는 1-1.4 dS/m로 소폭 감소 되었으며 유기질 함량은 LeCSMS에서 36.9%로 SMS에 비하여 60% 이상 가장 큰 폭으로 감소 되었다. LeCSMS 를 기준으로 N (1.2%), P(2.3%), K(0.77%)함량이 조사되었으며 중금속은 모든 CSMS에서 기준치 이하였으며 Ca, Mg는 30%에서 60%이상 증가하였다. C/N비는 LeCSMS, HeCSMS에서 15% 낮았으나 PoCSMS에서 32%로 높게 나타났다. LeCSMS 처리에 따른 고추 유묘 생육효과는 시판 유기퇴비 처리구 등 대조 구에 비하여 초장이 60% 이상 높게 성장했으며 옆폭, 옆장, 옆수에서 다른 대조 구 에 비하여 모두 우수한 생육 효과를 보였다.

재생 불가능한 에너지 자원이 수년에 걸쳐 고갈됨에 따라, 재생 에너지 생산을 위한 보다 효과적인 방법에 대한 연구가 증가되었다. 연로전지 개발의 한 분야인 미생물 연료전지(MFC)는 이중 성능의 잠재력 덕분에 발전하였다. MFC는 박테리아와 같은 전극 감소 생물에서 전력을 모아서 전기 에너지를 생산한다. MFC는 폐수를 연료로 사용하여 에너지를 생산하고 폐수를 정화한다. 양성자 교환막(PEM)은 양극과 음극 챔버의 분리막으로, 양성자만 효과적으로 통과할 수 있게 하는 중요한 역할을 한다. Nafion은 MFC에 상업적으로 사용되는 PEM이지만 비용, 생산 시간, 양성자 전도성 차원에서 보완할 점들이 많다. 본 리뷰 논문에는 Nafion을 대체할 수 있는 새로 개발된 PEM 몇 가지를 논의하였다. 또한, PEM, 혼합 PEM 및 복합 PEM에 기반한 MFC를 요약하고자 한다.

PURPOSES : In this study, the installation of drowsy rest areas and accidents are analyzed. The factors that affected the accidents caused by drowsy drivers in rest areas are analyzed to improve the safety of rest areas. METHODS : By comparing and analyzing the installation status of the rest areas for drowsy drivers, the accident status were analyzed. The logistic regression model was used to analyze the factors that affect accidents in the drowsy rest area. RESULTS : Most rest areas were installed below the installation criteria. Several accidents occurred when the vehicle entered the drowsy rest area. These rest areas had a short entry ramp, and no safety facilities were installed. The logistic regression model showed that the risk of an accident is lowered when the deceleration lane is longer than 215 m. Additionally, the risk of an accident is lowered when the rest area is installed in the straight section or the curve section, wherein the curve radius is greater than 2 km. CONCLUSIONS : In this study, we evaluated the installation status of the rest areas for drowsy drivers by comparing installation elements. Most rest areas for drowsy drivers were installed at different lengths of the ramp. Some of these were installed on the slope or curved sections of the road. We analyzed the accident status and developed an accident modal using the logistic regression model to identify the factors that affect accidents. It will be necessary to analyze accidents in drowsy rest areas continuously to improve safety for drowsy drivers.

This paper reports the pH effect of reduced graphene oxide (RGO) colloids on formation of three dimensional (3D) graphene network in nucleate boiling condition, so called boiling method. When nucleated bubbles grow on the hot surface, thin liquid film beneath the bubble is supposed to be dried, in which RGO flakes become close to each other and form a structure. Accordingly, what happened when they are in high particle density would be a key issue for the formation of 3D graphene network. Here, we changed pH and oxidation level of RGO colloids so that their effect was observed on extent of 3D graphene network after boiling method. As pH was lower, i.e. being acid, the RGO colloids become unstable, resulting in 3D structure rather than 2D structure. Similarly, As oxidation level was lower, i.e. being more reduced, it showed a tendency to form 3D structure.

Amorphous In-Ga-Zn-O (a-IGZO) thin film transistors, because of their relatively low mobility, have limits in attempts to fulfill high-end specifications for display backplanes. In-Zn-O (IZO) is a promising semiconductor material for high mobility device applications with excellent transparency to visible light region and low temperature process capability. In this paper, the effects of working pressure on the physical and electrical properties of IZO films and thin film transistors are investigated. The working pressure is modulated from 2 mTorr to 5 mTorr, whereas the other process conditions are fixed. As the working pressure increases, the extracted optical band gap of IZO films gradually decreases. Absorption coefficient spectra indicate that subgap states increase at high working pressure. Furthermore, IZO film fabricated at low working pressure shows smoother surface morphology. As a result, IZO thin film transistors with optimum conditions exhibit excellent switching characteristics with high mobility (≥ 30cm2/Vs) and large on/off ratio.

This study deals with the effects of austempering time on the microstructure and mechanical properties of ultrahigh strength nanostructured bainitic steels with high carbon and silicon contents. The steels are composed of bainite, martensite and retained austenite by austempering and quenching. As the duration of austempering increases, the thickness of bainitic ferrite increases, but the thickness of retained austenite decreases. Some retained austenites with lower stability are more easily transformed to martensite during tensile testing, which has a detrimental effect on the elongation due to the brittleness of transformed martensite. With increasing austempering time, the hardness decreased and then remained stable because the transformation to nanostructured bainite compensates for the decrease in the volume fraction of martensite. Charpy impact test results indicated that increasing austempering time improved the impact toughness because the formation of brittle martensite was prevented by the decreased fraction and increased stability of retained austenite.

Lightly reinforced concrete (RC) moment frames may suffer significant damage during large earthquake events. Most buildings with RC moment frames were designed without considering seismic loads. The load-displacement response of gravity load designed frames could be altered by masonry infill walls. The objective of this study is to investigate the load-displacement response of gravity load designed frames with masonry infill walls. For this purpose, three-story gravity load designed frames with masonry infill walls were considered. The masonry infilled RC frames demonstrated larger lateral strength and stiffness than bare RC frames, whereas their drift capacity was less than that of bare frames. A specimen with a partial-height infill wall showed the least drift capacity and energy dissipation capacity. This specimen failed in shear, whereas other specimens experienced a relatively ductile failure mode (flexure-shear failure).

이 연구는 유기농 식물성 계면활성제의 화장품 가용화력에 관한 연구이다. 유기농으로 인증된 원료를 사용하여 고순도의 폴리글리세릴-10올리에이트와 폴리글리세릴-10스테아레이트를 합성하여 우수한 가용화력을 가진 계면활성제를 개발하였다. 이 혼합원료의 이름을 Solubil ORG-1300으로 칭하였다. 이 원료의 외관은 엷은 노란색의 페이스트이었고, 특이한 고유의 냄새를 가지고 있었다. 비중은 1.15, 산가는 0.072±0.1로 순도가 높았다. 이 계면활성제의 HLB값은 평균값=15.1로 Griffin식을 사용 하여 계산하였다. 유기농 가용화제가 향과 오일을 어떻게 가용화되는가를 메커니즘적으로 해석하였다. 가용화 실험은 두 가지 오일에 대하여 성능실험을 통하여 육안으로 판별하고 UV분광광도계로 890nm에서 투과도를 측정하여 투명도를 평가하였다. 이 결과 베르가못오일을 가용화하는데 필요한 계면활성제의 농도는 약 2배정도가 필요한 것으로 나타났다. 또한 토코페릴아세테이트를 가용화하는데 필요한 계면활성제의 농도는 약 8배정도가 필요한 것으로 나타났다. pH변화에 따른 가용화력을 실험한 결과 pH=3.5의 산성영역, pH=7.2의 중성영역, pH=11.5의 알칼리성영역에서도 안정화된 가용화력을 보였다. 화장품의 응용분야로써 보습스킨토너 처방을 성공적으로 개발하였다. 이러한 결과를 바탕으로 스킨케어, 베이비 로션, 민감성 혹은 아토피 피부용 화장품에 폭넓게 응용이 가능할 것으로 기대한다.

This paper reports an uncertainty analysis of quantitative visualization methodology for slug bubble dynamics in downward-facing nucleate boiling condition. Measurement of dynamics of slug bubble, i.e. departing speed, frequency, and diameter, is very important to predict safety margin of thermal systems in moving vehicle. By employing high speed visualization and post-processing, we quantitatively measured the volume and location of slug bubble, so that vapor generation rate and departing speed data were derived from their time differentiation. As a visualization methodology, its reliability was evaluated via uncertainty analysis. For 95% confidence interval, uncertainty of vapor generation rate and departing speed were 3% and 2%, respectively, and which were one order lower than standard deviation of those data.

Microbubble is a part of advanced water treatment technologies, and there are several ways for microbubble generation. A strategy using Venturi (convergent-divergent) nozzle with air-suction holes has advantage of energy and time saving compared with the others. Here, we used 3D printer to make the various nozzle geometries in order to understand two-phase flow in the Venturi nozzle and air-breaking mechanism. It was evaluated the effects of convergent and divergent angles independently on air-suction rate and pressure drop, and the two-phase flow (air bubbles and liquid water) were observed. The convergent angle strongly affect the air-suction rate corresponding with increase of pressure drop. Meanwhile, as the divergent angle increased, it became dominant the minor loss by sudden enlargement of flow area, so that the air-suction rate and pressure drop showed decreased.

To meet the current demand in the fields of permanent magnets for achieving a high energy density, it is imperative to prepare nano-to-microscale rare-earth-based magnets with well-defined microstructures, controlled homogeneity, and magnetic characteristics via a bottom-up approach. Here, on the basis of a microstructural study and qualitative magnetic measurements, optimized reduction conditions for the preparation of nanostructured Sm-Co magnets are proposed, and the elucidation of the reduction-diffusion behavior in the binary phase system is clearly manifested. In addition, we have investigated the microstructural, crystallographic, and magnetic properties of the Sm-Co magnets prepared under different reduction conditions, that is, H2 gas, calcium, and calcium hydride. This work provides a potential approach to prepare high-quality Sm-Co-based nanofibers, and moreover, it can be extended to the experimental design of other magnetic alloys.