In this study, benzoxazolo carbocyanine is of industrial importance as green-sensitizing dye in the spectral sensitization. Sensitizing dye was prepared by the reaction of 2-methyl-3-sulfopropyl-4,5-benzoxazolium (inner salt) with triethyl orthobenzoate in the presence of triethylamine. The product was identified by using various analytical tools such as elemental analyzer, IR spectrophotometer, UV-Vis spectrophotometer, 1H-NMR spectrometer, TGA and DSC. The maximum absorption peak in methanol solvent was 507 nm. Therefore, it was concluded that benzoxazolo carbocyanine dye can be used as sensitizing dye for the spectral sensitization of photographic emulsion and color cosmetics.

In order to fine antioxidant and whitening agent source from nature, the comparisons of antioxidative activity and tyrosinase inhibitory activity were carried out for various ethanol extract on Pueraria Radix, Poria Cocos, and Coptidis Rhizoma. Comparing for three ethanol extracts, the highest electron donating ability was found at Poria Cocos (81.2%), but, the highest SOD-like ability, at the Coptidis Rhizoma(58%). Xanthine oxidase experiment exhibited 23.3% of hindrance effect in Pueraria Radix, and 79.3% in Poria Cocos. To evaluate at the whitening effect, tyrosinase inhibitory activity was conducted. Tyrosinase inhibitory activity was detected at 17.9% in the Puerariae Radix, 5.2% in the Poria Cocos and 83.3% in the Coptidis Rhizoma. From these results, we suggest that the ethanol extracts from Pueraria Radix, Poria Cocos, and Coptidis Rhizoma can be used for cosmetic ingredients.

The performance of positive plates depends on the structure of the lead dioxide active mass. The positive active materials (PAM) consists of a skeleton, built up of agglomerates and macropores. Agglomerates, in their turn, comprise particles and micropores. This paper described a study conducted to determine the effects of different soaking times between the acid fill and formation stages of the tubular plate production. For the positive plates a lead oxide were filled into tubular bag with a red lead. After filling the positive plates were soaked in H2SO4 solution. X-ray diffraction(XRD), scanning electron microscopy(SEM) and electrical testing had been used to study the compositional and morphological aspects of the positive active material(PAM) just prior and after formation. Results indicate that PAM compositions were effected by the soaking time and acid density of H2SO4 solution. It can be seen that as the soaking time duration increases, α-PbO, Pb3O4, and Pb were all gradually sulphating. Composition of 3BS reached a maximum at around 3 h duration and H2SO4 of sp. gr. 1.10 on soaking. This results would suggest that the most beneficial conditions for soaking were the H2SO4 of sp. gr. 1.10 and 2 to 6 h of soaking.

The transformation of the liquid crystal complex made by binding of anionic surfactant, sodium dodecyl sulfate (SDS), into high charge density cationic polymer, the homopolymer of diallyldimethylammonium chloride (PDADMAC) was induced by adding of nonionic surfactants and investigated by means of microscopy and FE.SEM. Among nonionic surfactants in this experiments polyethylene glycol (3 mol) ether of lauryl alcohol (laureth-3) made variation in the complex. The laureth-3 transformed the complex into spherulite vesicle with the size of ca.100μm. This change increased the viscosity and the turbidity of the solution phase separated originally. Microscope showed that they are spherulite particles and polarized microscope suggested they are multi.lamellar liquid crystals. FE-SEM also proved that explicitly.

Hemp seed oil and evening primrose oil were incorporated into the diets of laying hens for 5 weeks and the level of gamma fatty acid in the eggs that the treated hens laid was then evaluated. Hens were fed corn-soybean based diets that contained 5% tallow, 5% corn oil (CO), 5% hemp seed oil (HSO), or 5% evening primrose oil (EPO). The hemp seed oil and evening primrose oil influenced the amount of gamma linolenic acid found in the eggs through blood. The level of gamma linolenic acid in the plasma was significantly higher in hens that received the HSO and EPO diets than in those that received the tallow and CO diets. The HSO and EPO diets led to a 1.09% and 4.87% increase in egg gamma linolenic acids, respectively, when compared with eggs produced by hens treated with tallow and CO. Taken together, these data demonstrate that healthy eggs with increased gamma linolenic acids can be generated by minor diet modifications when hemp seed oil or evening primrose oil is included in the hen diet.

Recent years have brought remarkable developments in white light emitting devices (WLEDs) and white organic light-emitting devices (WOLEDs). However, their efficiency, CIE values, CRI and lifetime are still not ideal. This review covers detailed discussion about syntheses of organometallic complexes, inorganic phosphors and quantum dots used in WLEDs, WOLEDs and their electroluminescent properties until December 2007.

This study is focused on the antimicrobial activity of cyanobacteria Microcystis aeruginosa by the reduction and oxidation reaction of copper and zinc alloy metal fiber filter. Cu/Zn ion is easily makes radicals with molecular hydroperoxide. Especially, hydroperoxide radical shows strong toxicity to the strains. Plasma membrane causes conformational change when hydroperoxide radical binds to plasma membrane. Elution of copper ion from copper and zinc alloy metal fiber is detected in the cyanobacteria solution as 0.5 ppm, and that of zinc ion is 0 ppm respectively. Zinc ion is figured to form a hydroxide in the cyanobacteria solution and precipitated to form a sludge. The concentration of chlorophyll-a in the cyanobacteria solution was proved to be the index of antimicrobial level of Microcystis aeruginosa.

Nanocomposites with polypropylene/clay/wood flour were prepared by melt blending and injection molding. Thermal, mechanical and morphological properties were characterized. The addition of ballmilled clay, compatibilizer and wood flour significantly improved the thermal stability of the hybrids. The tensile modulus and strength of most hybrids was highly increased with the increased loading of clay, maleated polypropylene (MAPP) and wood flour (WF), compared to the PP/WF hybrids. The tensile modulus and strength of most hybrids were highly increased with the increased loading of ballmilled clay, MAPP and wood flour, compared to the hybrids with PP/WF. The transmission electron microscopy (TEM) photomicrographs illustrated the intercalated and partially exfoliated structures of the hybrids with ballmilled clay, MAPP and wood flour.

The flame-retardant coatings were prepared by blending the synthesized triphosphorus modified polyester in the previous paper and hexamethylene diisocyanate-trimer and curing it at room temperature. The characterization of the films of the prepared coatings was performed. It was confirmed that no deterioration of physical properties of PU coatings was observed with the increasing phenylphosphonic acid (PPA) contents. Flame retardancy was tested by a 45˚ Meckel burner method and LOI method. With the 45˚ Meckel burner method, CATBTP-20C and CATBTP-30C that contain 20 wt% and 30 wt% of PPA, flame retarding component, respectively, showed the first grade flame retardancy with 2.8~3.9 cm of char length ; and, with LOI method, they exhibited a good flame retardancy as a range of 30~32% of combustion values.

The polyamide-amide-imide (PAAI) was synthesized by reacting 4,4'-diaminobenzanilide (DBA) with trimellitic anhydride chloride using a two-stage heating. The precursor of polyamide-acids was formed at first stage and followed by the formation of imide of PAAI. Two polyamide-imides (PAIs) were prepared from benzidine (BZ) or 4,4'-diaminodiphenylether (DPE) with trimellitic anhydride chloride. These three polymers had glass transition temperature in the temperature range of 240-250℃. X-ray data were obtained on thin film specimens cured at 250℃. There was a minimal kind of short-range order consisting of the most probable distances between neighboring chains. The average segmental spacing of short-range order decreased in the order of polymers obtained from 4,4'-diaminobenzanilide (DBA), polyamide-imide, and 4,4'-diaminodiphenylether (DPE). The imidization of three polyamide-imides was confirmed by 15N MAS NMR and FT-IR spectroscopy. 15N NMR spectrum of cured polyamide-imide showed imide 15N peak, thereby providing an evidence for the imidization of three polyamide-imides.

Chemicals for cosmetics, including skin, the skin absorbs some of the research in the field of science or pharmacy recently, about the environment and the health of the heightened interest in skin absorption, and many other human attributes and absorption evaluation studies are underway in various areas. In this study, The effects of commercial permanent wave products to skin which are composed with cysteine and bases using rat. Results are as follows; the content of penetration 4 hours later with steady state and no significant changeable after 20 hours later. In cysteine groups lag time and permeability coefficient of young skin is 3.32hr and 0.102μg/cm2·hr, lag time and permeability coefficient of old skin is 4.04hr and 0.106μg/cm2·hr. In conclusion of study lag time and permeability coefficient in old skin and wounded skin are faster than healthy skin. We notified that fine rinkle and rash of skin were changeable in the case of treating with permanent wave drugs than normal skin.

xTiO2-ySiO2 system photocatalysts were developed by sol-gel method based on the change of production parameters, and their structure of crystallization and the specific surface area were measured. Considering the efficiency of the ethanol and phenol degradation using the catalyst, the conclusions were obtained as follows: By means of X-ray analysis of xTiO2-ySiO2 powder that is obtained from Titanium and Silicon alkoxide by sol-gel process, it is shown that crystal structure of anatase type is a dominating structure and, on the other hand, the structure of rutile also partly exists. The increase of SiO2 contents causes the decrease of the degree of crystallization of the gel, whereas the specific surface area preferentially increases. It is shown that more than 90% of ethanol and phenol are degraded when reaction time is about three and an hours, and the maximum degradation rate of ethanol and phenol is shown in 60TiO2-40SiO2 catalyst.

Transdermal therapeutic system(TTS) is often used as the method of drug dosage into the epidermic skin. Natural polymer were selected as ointment material of TTS. We investigated the permeation of natural polymer ointment containing drug in rat skin using horizontal membrane cell model. Permeation properties of materials were investigated for water-soluble drug such as Nicotinic acid N-oxide in vitro. These results showed that skin permeation rate of drug across the composite was mainly dependent on the property of ointment base and drug. Proper selection of the polymeric materials which resemble and enhance properties of the delivering drug was found to be important in controlling the skin permeation rate. This result suggests a possible use of natural polymer ointment base as TTS of antihyperlipoproteinemic agent.

The hydrosilylation is an addition reaction of Si-H bond to unsaturated double bonds, which provides a convenient mechanism to synthesize poly(dimethylsiloxane-co-methylsiloxane)copolymer having siloxy units in polymer backbone. In this study, Poly(dimethylsiloxane-co-methylsiloxane) copolymer was synthesized through the polymerization reaction of cyclopentasiloxane with poly(methyl-hydrogen) siloxane. Silicone-hydrogen functional group of the poly(dimethylsiloxane-co-methylsiloxane) copolymer was substituted to the alkyl groups by hydrosilylation. And their structure was analyzed with FT-IR, H-NMR and GPC instruments, respectively. Surface tension of the synthetic compounds is increased from 22dyne/cm to 25dyne/cm according to increase additional EO moles. The cmc which was evaluated by surface tension was ranged 10-5 to 10-4mol/L and it was decreased according to increase of dimethyl siloxyl content. HLB number of these surfactants was evaluated 9.5 to 11.5 range. These silicone surfactants is applied to self-emulsifier defoamer and personal care products as surface tension depressant, emulsifier, foam control agent.

In this article a reliable and rapid method based on specific turbidimetry is proposed for the determination of sizes of nanoparticles. Conventionally in specific turbidimetry specific turbidities for a colloidal dispersion are measured as a function of light wavelength, and compared to theoretical values calculated from Mie scattering theory for presumed particle sizes. In contrast specific turbidity at a fixed wavelength is measured in the proposed method, and particle sizes are determined from the prepared calibration curve. The calibration curve is a plot of specific turbidity vs particle size and in this case the specific turbidities are measured for a couple of samples of known sizes.

Development of white light emitting materials has been an interesting area for scientists and scientists have developed many organic, polymer and inorganic materials for white electroluminescent devices. Among them, single component small molecules gave best results in terms of efficiency, simplicity of device fabrication, and CIE values. Therefore, this review covers detailed discussion about syntheses of small compounds used in white organic light emitting devices until 2007.

The core-shell latex particles were prepared by sequential emulsion polymerization using alkyl methacrylate as a shell monomer and potassium persulfate (KPS) as an initiator. We study the effects of core-shell structure of calcium carbonate/alkyl methacrlyate in the presence of an anionic surfactant sodium lauryl sulfate (SLS) and polyoxyethylene alkyl ether sulfate (EU-S133D)). The structure of core-shell polymer were investigated by measuring to the thermal decomposition of polymer composite using thermogravimetric analyzer and morphology of latex by transmission electron microscope (TEM).

This study was done to investigate the antidiabetic and antioxidant effects of Lycii fructus in Streptozotocin (STZ)-induced diabetic rats. Diabetes was induced by intravenous injection of STZ at a dose 45mg/kg.b.w. dissolved in citrate buffer(pH4.5). The ethanol extract of Lycii fructus was orally administrated once a day for 7 days. The contents of serum glucose, total cholesterol were significantly decreaed (p<0.05) in Lycii fructus treated group compared to the those of STZ-control group, also content of Triglyceride (TG), Altherogenic index (AI) were decreased, but not statistically significant. But high density lipoprotein (HDL)-cholesterol and HDL-cholesterol/total cholesterol ratio (HTR) were increased in Lycii fructus treated group compared to the those of STZ-control group. The content of hepatic glycogen and activities of glucose-6-phosphate dehydrogenase(G-6PDH), glutathione-s-transferase(GST), superoxide dismutase(SOD) were significantly increased(p<0.05), glucose-6-phos-phatase(G-6pase)was significantly decreased(p<0.05) and The glutathione(GSH), glucokinase(GK) were increased. But not statistically significant In Lycii fructus treated group compared to the those of STZ-control group These results indicated that ethanol extract of Lycii fructus would have antidiabetic and antioxidant effects in STZ-induced diabetic rats.

The ion exchangers supported on silica gel containing primary, secondary, or tertiary amine groups show a behaviour that is weakly acidic, while the quaternary salts are strongly acidic. These properties change according to the hydrophilicities of the modifier functional groups. Ammonium salt derivatives supported on silica gel were prepared from silica modified with 3-Aminopropyltriethoxysiliane and N-3-(Trimethoxysilyl)propylehtylene diamine. The preparation and the ion exchange properties of two systems were discussed. Two systems have different hydrophilicities and contain ammonium chloride derivatives of 3-amminopropyltriethoxysilane and N-3-(triehtoxysilyl)propyl ethylene diamine supported on silica gel, SA+/Cl- and SA+/Cl-, respectively. The high affinity to perchlorate ion presented by the SA+/Cl- through the equilibrium studies of ion exchange led us to its application as an ion selective electrode for the perchlorate ion. The determination of the perchlorate ion in the presence of other anions and in complexes is very difficult. Few analytical methods are available and most of them are indirect. Both materials showed potential use as an ion exchanger; they are thermically stable, achieve equilibrium rapidly in the presence of suitable exchanger ions, and are easily recovered.

Pretreatment of eliminating FFA is needed to make biodiesel from animal fat recovered from leather wastes because its acid value is high. This study was carried out to investigate the influence of 4 different pretreatment methods, which are heterogeneous catalyst method, ion exchange resin method, low pressure.high temperature method, and alkali method on the eliminating FFA and fatty acid composition. The results showed that the rate of eliminating FFA increased in the order of alkali method > catalyst method > low pressure high temperature method > ion exchange method. In the case of pretreatment of alkali method using NaOH, the rate of eliminating FFA appeared more than 86% regardless of acid value. Therefore, it was considered that alkali method using NaOH was the most effective in the view of economical and productive aspects, taking it into account that the acid value of animal fat recovered from fleshing scrap generated during leather making processes was 7 to 8.