A number of roller-compacted concrete pavements (RCCP) have been constructed without saw-cut joints in order to save construction cost. Then it will allow natural cracks to randomly occur at the early age after concrete placement. Crack spacing of unjointed RCCP is crucial to ensure an adequate crack width and load transfer across the cracks since large crack spacing will result in excessive crack width and reduce load transfer efficiency that may be cause faulting, excessive deflection, and further cracking in RCCP slab. Due to pavement thickness, climatic condition, and material properties, unjointed RCCP may have different natural crack spacing. In this study, an analytical approach to predict natural crack spacing of an unjointed RCCP was developed. An analytical method based on elastic theory to calculate axial restraint stress using a bilinear slab-subbase interfacial constraint assumption was conducted. Curling stress induced by temperature gradient through the depth of the slab was also considered. The analytical model incorporates the environmental effect, strength gain and modulus of elasticity, coefficient of thermal expansion, drying shrinkage, base type materials, and slab geometries. The predicted crack spacing results obtained from the predictive model were validated through field measured data. The results showed a good agreement compared with crack spacing measured in the field. Furthermore, the result from a sensitive analysis using proposed predictive model showed that crack spacing increased when thickness of RCCP increased. The predicted crack spacing results may be used as input parameters to estimate crack widths in unjointed RCCP under given climatic condition, and material properties. If estimated crack width is excessive and cannot maintain an adequate load transfer across the cracks, saw-cut joints with an appropriate spacing should be provided in order to minimize crack width, and to prevent future cracking of RCCP leading to better performance.

Roller-compacted concrete (RCC) has been widely used for construction of pavements [1]. The strength of RCCP can be obtained from not only hydration of binder but also the aggregate interlock resulted from roller-compaction [2]. For this reason, RCCP normally achieves higher strength compared to conventional concrete pavement with similar cement content. Even though RCCP can be provided a good structural performance, it has been difficult to verify the long-term performance though actual field construction. Therefore, this study aimed to investigate the fatigue characteristics and crack development in RCCP based on full-scale fatigue test and accelerated pavement test. In case of full-scale fatigue tests, fatigue behavior was evaluated by using 1 m × 1 m dimensional RCC slab specimens obtained from the field in order to consider the field variability. Fatigue equation derived from this study shows that the number of load repetitions which causes fatigue failure at the same stress level is slightly larger than that of PCA fatigue equation. In order to evaluate the performance of RCCP, two phases of accelerated pavement test (APT) were conducted. In phase one, the performance of RCCP at two different strengths (35.6 and 30.4 MPa) was evaluated. In phase two, the performance of RCCP with different thickness (5, 7.5 and 10 cm) was investigated. The number of load repetition of fatigue crack occurrence in each section was compared to the estimated fatigue failure determined from fatigue equation of RCCP. The crack development in each section was compared to the AASHTO crack model for JPCP. Overall, it was confirmed that RCCP has equal or better performance compared to JPCP the estimation in term of fatigue cracking. The fatigue equation from PCA and cracking model from AAHTO can be used on RCCP at certain design thickness range.

PURPOSES: A composite pavement utilizes both an asphalt surface and a concrete base. Typically, a concrete base layer provides structural capacity, while an asphalt surface layer provides smoothness and riding quality. This pavement type can be used in conjunction with rollercompacted concrete (RCC) pavement as a base layer due to its fast construction, economic efficiency, and structural performance. However, the service life and functionality of composite pavement may be reduced due to interfacial bond failure. Therefore, adequate interfacial bonding between the asphalt surface and the concrete base is essential to achieving monolithic behavior. The purpose of this study is to investigate the bond characteristics at the interface between asphalt (HMA; hot-mixed asphalt) and the RCC baseMETHODS: This study was performed to determine the optimal type and application rate of tack coat material for RCC-base composite pavement. In addition, the core size effect, temperature condition, and bonding failure shape were analyzed to investigate the bonding characteristics at the interface between the RCC base and HMA surface. To evaluate the bond strength, a pull-off test was performed using different diameters of specimens such as 50 mm and 100 mm. Tack coat materials such as RSC-4 and BD-Coat were applied in amounts of 0.3, 0.5, 0.7, 0.9, and 1.1ℓ/m2 to determine the optimal application rate. In order to evaluate the bond strength characteristics with temperature changes, a pull-off test was carried out at -15, 0, 20, and 40 °C. In addition, the bond failure shapes were analyzed using an image analysis program after the pull-off tests were completed.RESULTS: The test results indicated that the optimal application rate of RSC-4 and BD-Coat were 0.8ℓ/m2, 0.9 ℓ/m2, respectively. The core size effect was determined to be negligible because the bond strengths were similar in specimens with diameters of 50 mm and 100 mm. The bond strengths of RSC-4 and BD-Coat were found to decrease significantly when the temperature increased. As a result of the bonding failure shape in low-temperature conditions such as -15, 0, and 20 °C, it was found that most of the debonding occurred at the interface between the tack coat and RCC surface. On the other hand, the interface between the HMA and tack coat was weaker than that between the tack coat and RCC at a high temperature of 40 °C.CONCLUSIONS: This study suggested an optimal application rate of tack coat materials to apply to RCC-base composite pavement. The bond strengths at high temperatures were significantly lower than the required bond (tensile) strength of 0.4 MPa. It was known that the temperature was a critical factor affecting the bond strength at the interface of the RCC-base composite pavement.

PURPOSES :Infiltration of moisture, polluted material, and deicer into concrete, accompanied by freeze and thaw can cause significant deterioration of concrete pavement. In order to protect concrete from deterioration, it is necessary to prevent the infiltration of these concrete external materials. The moisture-repellent agent, which is a surface treatment and maintenance material added to concrete structures to render them water resistant, has advantages such as prevention of water infiltration and security against air permeation. Nano-coat, which is referred to as silicon hydride, is typically used as a moisture-repellent agent. Therefore, in this study, an attempt is made to use penetration-type Nano-coat as an alternative in order to evaluate its applicability through environmental resistance tests.METHODS:This study aimed to evaluate the applicability of penetration-type Nano-coat, which can provide water repellency to concrete, in concrete pavements, through various environmental resistance tests such as freezing and thawing resistance, chloride ion penetration resistance, and surface scaling resistance tests. The applicability of penetration-type Nano-coat was demonstrated based on the specification of KS F 2711, KS F 2456, and ASTM C 672.RESULTS :In the case of penetration-type Nano-coat applied on sound concrete, an increase in concrete durability was demonstrated by the negligible chloride ion penetrability and the absence of scaling, as revealed by visual observation of the surface, after 50 cycles of scaling resistance test. In addition, test result of the application of penetration-type Nano-coat on deteriorated concrete established that concrete surface pretreated by grinding provided improved durability than non-treated concrete.CONCLUSIONS:This study indicates that penetration-type Nano-coat is applicable as an effective alternative, to increase the durability of concrete structures. In addition, it was known that pretreatment of deteriorated concrete surface, such as grinding, is required to improve the long-term performance of concrete pavement.

PURPOSES:Pavement textures can be categorized into four according to wavelength: microtexture, macrotexture, megatexture (roads), and roughness. Pavement surface texture influences a number of aspects of tire-pavement interaction such as wet-weather friction, tire-pavement noise, splash, spray, tire-wear, and rolling resistance. In particular, macrotexture is the pavement surface characteristic that considerably impacts tire-pavement noise. In general, it can be demonstrated that tire-pavement noise increases with the increase of texture depth and wavelength. Recently, mean profile depth (MPD) and wavelength have been used to evaluate tire-pavement noise. This study aimed to identify the relationship between mean profile depth and average wavelength for asphalt pavement based on the information obtained on a number of asphalt pavement sections.METHODS :Profile data were collected from a number of expressway sections in Korea. In addition, mean profile depth and average wavelength were calculated by using this profile data. Statistical analysis was performed to determine the correlationship between mean profile depth and average wavelength.RESULTS:This study demonstrates a linear relationship between mean profile depth and average wavelength for asphalt concrete pavement.CONCLUSIONS:The strong relationship between mean profile depth and average wavelength of asphalt pavement was determined in this study.

Workers are avoiding production/manufacturing sites due to the poor working environment and concern over safety. Small and medium-sized businesses introduce new equipment to secure safety in the production site or ensure effective process management by introducing the real-time monitoring technique for existing equipment. The importance of real-time monitoring of equipment and process in the production site can also be found in the ANSI/ISA-195 model. Note, however, that most production sites still use paper-based work slip as a process management technique. Data reliability may deteriorate because information on the present condition of the production site cannot be collected/analyzed properly due to manual data writing by the worker. This paper introduces the monitoring and process management technique based on a direct facility interface to secure safety in the field by improving the poor working environment and enhance there liability and real-time characteristics of the production data. Since the data is collected from equipment in real-time directly through the SIB-based interface and PLC-based interface, problems associated with workers’ manual data input are expected to be solved; safety can also be improved by enhancing workers’ attention to work by minimizing workers’ injuries and disruption.

후행 핵연료주기 경제성 평가는 추정 비용의 불확실성, 평가 대상기간의 장기성, 적용 할인율에 따른 계산결과의 변동성 등 많은 불확실성을 내포하고 있기 때문에 평가기관 또는 평가자에 따라 그 결과가 서로 상이하다. 본고에서는 지금까지 수행 된 주요 경제성 평가 연구들을 조사/분석하여 그 특징과 한계를 알아봄으로써 현재 국내에서 추진되고 있는 사용후핵연료 공론화 및 후행 핵연료주기 정책 연구 추진에 기초자료로 활용될 수 있도록 하고자 하였다. 분석 결과 사용후핵연료 재활용 옵션에 비해 직접처분 옵션이 유리하나, 입력 자료로 사용된 파라미터 값에 따라 결과의 불확실성이 많이 나타나 이 부분에 대한 추가적인 연구가 필요하다는 사실을 알 수 있었다.

Polluting gases emitted from industrial sites take compound forms consisting of gaseous and particulate phases. Localization of PTFE membrane filters has thus been initiated to remove particulate materials and mercury, which is a heavy and hazardous metallic element. More specifically, a PTFE membrane filter was fabricated by thermal laminating technology to vary porosity on the filter surface for removal of particulate materials thereon. Optimized equi-biaxial stretching ratio control enables minimization of large-size pore formation with an average pore size of 0.58 μm and improved air permeability of 8.03 cm3/cm2/sec. Various adsorbents were tested for removal of mercury vapor by surface treatment of the PTFE membrane filter. The filter’s surface was further altered using functional amine group compounds: one composed of silane coupling agent (APTMS) was found suitable as a mercury adsorbent. When ACF with a large surface area was used as support material, mercury removal efficiency increased threefold to 0.162 mg/g-ACF. Furthermore, the developed PTFE membrane filter was tested in its capacity of differential pressure and filtering efficiency using a pilot scale particulate removal unit. Stable and consistent differential pressure was maintained during long-term operation and less frequent periods of filter shutdown due to pores filling with 99.96% of particulate removal efficiency, which was more than satisfactory filtration efficiency.