In the nuclear fuel cycle (NFC) facilities, the failure of Heating Ventilation and Air Conditioning (HVAC) system starts with minor component failures and can escalate to affecting the entire system, ultimately resulting in radiological consequences to workers. In the field of air-conditioning and refrigerating engineering, the fault detection and diagnosis (FDD) of HVAC systems have been studied since faults occurring in improper routine operations and poor preventive maintenance of HVAC systems result in excessive energy consumption. This paper aims to provide a systematic review of existing FDD methods for HVAC systems therefore explore its potential application in nuclear field. For this goal, typical faults and FDD methods are investigated. The commonly occurring faults of HVAC are identified through various literature including publications from International Energy Agency (IEA) and American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE). However, most literature does not explicitly addresses anomalies related to pressure, even though in nuclear facilities, abnormal pressure condition need to be carefully managed, particularly for maintaining radiological contamination differently within each zone. To build simulation model for FDD, the whole-building energy system modeling is needed because HVAC systems are major contributors to the whole building’s energy and thermal comfort, keeping the desired environment for occupants and other purposes. The whole-building energy modeling can be grouped into three categories: physics-based modeling (i.e., white-box models), hybrid modeling (i.e., grey-box models), and data-driven modeling (i.e., black-box models). To create a white-box FDD model, specialized tools such as EnergyPlus for modeling can be used. The EnergyPlus is open source program developed by US-DOE, and features heat balance calculation, enabling the dynamic simulation in transient state by heat balance calculation. The physics based modeling has the advantage of explaining clear cause-and-effect relationships between inputs and outputs based on heat and mass transfer equations, while creating accurate models requires time and effort. Creating a black-box FDD model requires a sufficient quantity and diverse types of operational data for machine learning. Since operation data for HVAC systems in existing nuclear cycle facilities are not fully available, so efforts to establish a monitoring system enabling the collection, storage, and management of sensor data indicating the status of HVAC systems and buildings should be prioritized. Once operational data are available, well-known machine learning methods such as linear regression, support vector machines, random forests, artificial neural networks, and recurrent neural networks (RNNs) can be used to classify and diagnose failures. The challenge with black-box models is the lack of access to failure data from operating facilities. To address this, one can consider developing black-box models using reference failure data provided by IEA or ASHRAE. Given the unavailability of operation data from the operating NFC facilities, there is a need for a short to medium-term plan for the development of a physics-based FDD model. Additionally, the development of a monitoring system to gather useful operation data is essential, which could serve both as a means to validate the physics-based model and as a potential foundation for building data-driven model in the long term.

The site used for a nuclear facility can be released after decommissioning if the results of dose estimation meet the regulatory requirements and the site release is approved by the regulatory body. RESRAD-ONSITE, developed by the Argonne National Laboratory, is a computer code used to estimate the dose to the residents on radiologically contaminated sites. The dose estimation for site release should consider various exposure pathways, including inhalation, ingestion, and external exposure. This study used RESRAD-ONSITE to evaluate the internal exposure dose and identify radionuclides due to the intake of food produced on radiologically contaminated sites. The upper limit of the clearance level of radionuclides expected to remain at the site was used as the source terms for the dose evaluation. In addition, the amount of food intake per capita was obtained from eight countries using nuclear power generation as of 2020. The default values of RESRAD were used for other parameters except for intake by type of food and source terms. As a result of the dose evaluation, the contaminated water and vegetables showed a great contribution to the exposure dose. The dose due to tritium in drinking water was highest in the third year. In addition, regarding the intake of vegetables, the internal exposure due to 90Sr was the highest in the first year.

The domestic representative nuclear fuel cycle facilities are post-irradiation examination facility (PIEF) and Irradiated Examination Facility (IMEF) at KAERI. They have regularly operated since 1991 and 1993, respectively. Due to the long period of use, the facilities are ageing, and maintenance costs are increasing every year. The maintenance methods have mainly been breakdown maintenance (BM) and partially preventive maintenance (PM). They involve replacing components that have problems through periodic inspections by on-site inspectors. However, these methods are not only uncertain in terms of replacement cycles due to worker’s deviation on the inspection results, but also make it difficult to respond accidents developed through failures on the critical equipment that confines radioactive material. Therefore, an advanced operation and maintenance studied in 2022 through all of nuclear facilities operated at KAERI. Advancement strategy in four categories (safety, sustainability, performance, innovativeness) was analyzed and their priorities according to a facility environment were determined so a roadmap for advanced operation and maintenance could be developed. The safety and sustainability are higher importance than the performance and innovativeness because facilities at KAERI has an emphasis on research and development rather than industrial production. Thus, strategy for advancement has focused even more on strengthening the safety and sustainability. To enhance safety, it has been identified that immediate improvement of aged structures, systems, and components (SSCs) through large-scale replacement is necessary, while consideration of implementing an ageing management program (AMP) in the medium to long term is also required. Facility sustainability requires strengthening operation expertise through training, education, and cultivation of specialized personnel for each system, and addressing outstanding regulatory issues such as approval of radiation environment report on the nuclear fuel processing facilities and improvement work according to fire hazard analysis. One of the safety enhancement methods, AMP, is a new maintenance approach that has not been previously applied, so it had to be thoroughly examined. In this study, an analysis was conducted on the procedure and method for introducing an AMP. An AMP for nuclear fuel cycle facilities was developed by analyzing the AMP applied to the BR2 research reactor in Belgium and modifying it for application to nuclear fuel cycle facilities. The ageing management for BR2 has the objective to maintain safety, availability and cost efficiency and three-step process. The first step is the classification of SSCs into four classes to apply graded approach. Secondly, ageing risk is assessed to identify critical failure modes, their frequency and precursors. Final step involves defining measures to reduce the ageing risk to an acceptable level in order to integrate the physical and economic aspects of ageing into a strategy for inspection, repair, and replacement. Similar approach was applied to the nuclear fuel cycle facility. Firstly, the SSCs of nuclear fuel cycle facilities have been classified according to their safety and quality classifications, as well as whether they are part of the confinement boundary. The SSCs involved in the confinement boundary were given more weight in the classification process, even if they are not classified as safety-class. A risk index for ageing was introduced to determine which prevention and mitigation measure should be chosen. By multiplying the health index and the impact index, the ageing risk matrix provides a numerical score that represents guidance on the prevention and mitigation of ageing effect. The health index is determined by combining the likelihood of failure and engineering evaluation of the current condition of SSCs, whereas the impact index is calculated by taking into account the severity of consequences and the duration of downtime resulting from a failure. This ageing management has to be thoroughly reviewed and modified to suit each facility before being applied to nuclear fuel cycle facilities.

The Kori Unit 1 and Wolsong Units 1, commercial reactors in South Korea, were permanently shut down due to the expiration of their design lifetime. Therefore, nuclear power plants that have been permanently shut down must be dismantled, and the site must be finally released after removing the remaining radionuclides. Domestic regulatory standards for site remediation should not exceed 0.1 mSv per year based on effective dose. In addition, it is necessary to calculate the preliminary Derived Concentration Guideline Levels (DCGL) to prove that the conditions are met. Therefore, in this study, the input factor considering the geological characteristics of the site of Kori Unit 1 was investigated, and the preliminary Derived Concentration Guideline Levels were calculated and compared with the results of previous studies. As a result of comparative analysis, 60Co, 134Cs, and 137Cs, which are gamma-ray emitting radionuclides, had similar values to DCGL of previous studies A and B. However, 63Ni, a beta-rayemitting nuclide, was 5.94×104 Bq·g−1 in this study and 8.47×101 Bq·g−1in previous study B, resulting in a difference of about 700 times. In addition, in the case of 90Sr, this study and previous study A were derived similarly, but this study was 5.34×101 Bq·g−1 and previous study B was 1.18×10−1 Bq·g−1, resulting in a difference of about 450 times. This difference is judged to be because, unlike this study using only the industrial worker scenario, in the case of previous study B, the resident farmer scenario was mixed and used, which considers the internal exposure caused by ingestion of food produced in the contaminated area. In this study, it was confirmed that DCGL according to the change of geological factors of the site did not have a significant effect on gamma-ray-emitting nuclides. However, it was confirmed that considering the intake of food affects the DCGL of beta-ray-emitting nuclides. Therefore, there is a need to conduct future studies applying intake input factors that meet domestic conditions.

This study was conducted to evaluate the efficacy of mulberry cake mixed diet on larval growth of Protaetia brevitarsis. As a result of adding mulberry cake to oak fermented sawdust and mulberry fermented sawdust, the survival rate of P. brevitarsis larvae were higher than those of the control when mass rearing larvae. When fed oak fermented sawdust with 3, 5% and 10% of mulberry cake, the cumulative proportion of larvae over 2.5g was 92.9% at 65 days, 90.8% at 55 days, and 96.3% at 45 days after rearing at 25±1℃, respectively. When fed mulberry fermented sawdust with 3%, 5% and 10% of mulberry cake, the cumulative proportion of larvae over 2.5g was 86.2% at 85 days, 90.7% at 75 days, and 91.5% at 75 days after rearing at 25±1℃, respectively.

This study was conducted to evaluate the efficacy of mulberry leaf mixed diet on larval growth of Protaetia brevitarsis. As a result of adding mulberry leaves to oak fermented sawdust, the survival rate of P. brevitarsis larvae were higher than those of the control when mass rearing larvae. When fed oak fermented sawdust with 5%, 10% and 20% of mulberry leaves, the cumulative proportion of larvae over 2.5g was 93.1% at 65 days, 95.6% at 55 days, and 93.9% at 55 days after rearing at 25±1℃, respectively. Also, heavy metals were not detected in larvae of P. brevitarsis fed on mulberry leaves.

In order to develop the D. adamsi breeding technique that is highly likely to be used as an emotional pet insect, the results of the D. adamsi was collected in the large exhibition Jang Tae-san in Daejeon to the indoor breeding began to spawn after 10 days after the training, the egg laying period was 33.6 days, the average number of spawn per female was 27.7, and the period was 11.8 days. D. adamsi larvae bred with food of oak-boiled molted two times, the duration of 1st larvae development was 11.8 days, 2nd larvae 14.5 days, and the third larvae was 29.4, and the larvae were used to build houses using Masato(soil) and in the pupae, and then in April of the following year. D. adamsi has a characteristic to build a house with fallen leaves and spawn one or two eggs in the fallen leaves, and the results of the spawn mat test using fallen leaves, leaf mold and a sawdust, etc., and the number of spawn was high in the Masato was spread about 3 ~ 5cm, and a fallen leaves on a 10 cm or so, and the growth and survival rate of the larvae were also high. Larvae breeding density was 2 ~ 3 ℓ in the container size to raise the object was normal growth, the higher the density mortality was high and the growth was sluggish. Larvae feeding conditions were normally developed in dry fallen leaves and fermented fallen leaves, compared to the sterile fallen leaves, oak sawdust, sterile fallen leaves and oak sawdust was abnormal, the mortality rate was higher than 50%.

This investigates the microstructure and mechanical properties of Al hybrid material prepared by electromagnetic duo-casting to determine the effect of heat treatment. The hybrid material is composed of an Al-Mg-Si alloy, pure Al and the interface between the Al-Mg-Si alloy and pure Al. It is heat-treated at 373, 573 and 773K for 1h and T6 treated (solution treatment at 773K for 1h and aging at 433K for 5h). As the temperature increases, the grain size of the Al-Mg-Si alloy in the hybrid material increases. The grain size of the T6 treated Al-Mg-Si alloy is similar to that of one heat-treated at 773K for 1h. The interface region where the micro-hardness becomes large from the pure Al to the Al-Mg-Si alloy widens with an increasing heat temperature. The hybrid material with a macro-interface parallel to the tensile direction experiences increased tensile strength, 0.2% proof stress and the decreased elongation after T6 heat treatment. On the other hand, in the vertical direction to the tensile direction, there is no great difference with heat treatment. The bending strength of the hybrid material with a long macro-interface to the bending direction is higher than that with a short macro-interface, which is improved by heat treatment. The hybrid material with a long macro-interface to the bending direction is fractured by cracking through the eutectic structure in the Al-Mg-Si alloy. However, in the hybrid material with a short macro-interface, the bending deformation is observed only in the limited pure Al.

강원도농업기술원에서는 2003년 무름병에 비교적 강하고 화색과 화형이 우수하고 장미 분홍색을 가진 Zantedeschia rehmanni × hybrid ‘Super Gem’과 연한 노랑색 품종 Z. × hybrid ‘Black Magic’을 각각 모본과 부본으로 하여 인공 교배 하였다. 2006년에 개화특성을 검정하여 화색과 화형이 좋은 ‘GZ0616’를 선발하였으며, 2007년에 포장 재배하여 자구 증식률, 초장과 초세 등 1차 특성검정 후 2차 선발하였다. 2013부터 2015년까지 특성검정과 재배시험을 통하여 균일성과 안정성이 인정되어 ‘강교C4-6호’로 최종 선발되었으며, 2017년 2월에 ‘립스마일(Lip Smile)’로 품종등록 되었다. 화포 외부의 주 색은 연노랑바탕 적자색(Y2C+RP79C)이며, 화포 높이는 8.5cm, 폭은 6.2cm로 대형화이다. 개화소요일수는 64.3일, 초장은 66.0cm, 괴경은 80.0g이다. 기호도 평가에서도 ‘Captain Rosette’와 유사하였으며, 절화용으로 이용 가능하다.

To be better fit for highways, pavement systems are required to provide comfortable and safe driving and be structurally durable. Composite pavements can be an effective option as they are more durable by placing a high functional asphalt overlay on a rigid concrete base layer. In order to apply a composite pavement system to the field, it is necessary not only to develop technologies that prevent reflecting crack and deterioration of the base layer, but also to improve bonding performance of materials and ensure structural performance as a pavement system against traffic loading. In advanced countries like Japan, USA and Europe, high-functional composite pavement systems are being put into practice across new highway networks. In this study, we evaluated structural performance (rutting, reflecting crack, and deflection) by applying traffic loads of actual highways through an accelerated pavement tester (APT) of a composite pavement section made up of a quiet porous surface laid over a water-proofing layer, a continuously reinforced concrete base, and a lean concrete sub-base layer, which was developed with new pavement methods used for each layer prior to field application. The APT specimen was constructed with paving materials and equipment actually used on site in the same dimensions (W3.5m*L14m*H2m) as actual highway sections in Korea, and 3-axle double-wheel heavy load (45ton) cart type KALES(Korean Accelerated Loading and Environmental Simulator) traveling on the specimen in both directions was used to simulate traffic loading. After applying around 8,574,000 ESALs of traffic loads, no reflecting crack occurred on the asphalt surface of the composite pavement, without surface distress except for rutting. In order to examine what causes rutting of pavements, we surveyed thickness of pavements by layer and measured asphalt density.

In Korea, concrete pavements were first applied to highways in 1981 and as a result of continued increase in length over the past years, 2,592 km of concrete pavement network is currently in service, of which 1,399 km(54%) of concrete pavements is 10 years or older, and 233km(9%) is 20 years or older. The length of concrete pavement sections nationwide has been steadily on the rise every year (EXTRI, 2017). Approximately 54% of current concrete pavement highway network will reach the service life limit in 2025 which means around 660 billion won is needed for future pavement repair project (EXTRI, 2017). Given that concrete pavements beyond design life still have a remaining service life, it is economically advantageous to repair them before reconstruction. Asphalt overlays are a major repair method for older concrete pavements. Depending on the concrete pavement condition, thickness and mixture of asphalt overlays are determined. Service life of asphalt overlays varies by the presence, time and size of cracks in existing concrete pavements and reflecting crack at joints. Temperature change of concrete pavement is among the major reaction parameters of reflecting crack. Reflecting crack develops when asphalt bottom-up cracking by longitudinal shrinkage and expansion due to temperature change of the concrete base layer, top-down cracking by temperature difference between top and bottom of concrete, and shear stress by traffic loading are combined (Baek, 2010). Crack and joint behaviors of concrete pavement vary between the base layer and the concrete surface of composite pavement system, and different conductivity by mixture and thickness of asphalt overlay leads to temperature change of concrete base course. This study measured temperatures of each layer of diverse composite pavements in place on site and analyzed differences in temperature change of concrete base layer depending on mixture and thickness of asphalt overlays. Overlay thickness parameters were 5cm and 10cm, two values most widely used, while mixture parameters were SMA and porous asphalt. Based on temperature change of concrete surface, this study also evaluated the difference of temperature change in concrete base layer with an asphalt overlay on top. Findings from this study are expected to be utilized for studies on mechanism and modeling of reflecting crack in old concrete pavements with asphalt overlays.

The aim of the study was to investigate the effects of incentive spirometry and Ujjayi breathing technique on the pulmonary function of smokers. Subjects were individuals who had a smoking habit of at least a year. Subjects were randomly divided into 3 groups: the incentive spirometry group (n=8), Ujjayi breathing technique (n=9), and a group applying both incentive spirometry as well as Ujjayi breathing technique (n=8). Each intervention was performed twice a day, 5 times a week, for a total of 8 weeks whereupon the change in pulmonary function was evaluated. A spirometer was used to measure FVC, FEV1, and FEV1/FVC. The survey used for this study included the Fagerström Test of Nicotine Dependence (FTND) and the Shortness of Breath Questionnaire (SOBQ). Study results for the comparison within groups showed that in the group that performed both the incentive spirometry and Ujjayi breathing technique, FEV1 improved with statistical significance (p<.05). Furthermore, within this comparison the FEV1/FVC improved with statistical significance. Comparison amongst the groups showed no statistically significant differences in all areas. Following, to effectively increase pulmonary function in young adult smokers, both incentive spirometry and Ujjayi breathing technique should be employed together.

The purpose of this study is to improve practical skill evaluation method of mushroom - trained certified technician's practical skill evaluation which is one of national qualification tests based on national incompetency standards. One of the current National Competency Standards (NCS), mushroom - trained certified technician uses NCS based practical assessment method. In order to improve the current practical evaluation method, we try to improve practical evaluation method based on field customized problem solving ability and improve the practical evaluation method, various evaluation methods should be constructed. On the purpose of identify the diversity and problems of the evaluation method, the experts of the group consultation, the mushroom-related research institute and the related industry collaborated to identify the problems of the actual mushroom - trained certified technician practicum test, This study on the evaluation improvement method was carried out. In this study, the contents of practical test of the current mushroom traits were analyzed and the trends of the latest mushroom industry were widely reflected.