The objectives of this research are to evaluate and compare the oxygen transfer coefficients(KLa) in both a general bubbles reactor and a micro-nano bubbles reactor for effective operation in sewage treatment plants, and to understand the effect on microbial kinetic parameters of biomass growth for optimal biological treatment in sewage treatment plants when the micro-nano bubbles reactor is applied. Oxygen transfer coefficients(KLa) of tap water and effluent of primary clarifier were determined. The oxygen transfer coefficients of the tap water for the general bubbles reactor and micro-nano bubbles reactor were found to be 0.28 hr -1 and 2.50 hr -1 , respectively. The oxygen transfer coefficients of the effluent of the primary clarifier for the general bubbles reactor and micro-nano bubbles reactor were found be to 0.15 hr -1 and 0.91 hr -1 , respectively. In order to figure out kinetic parameters of biomass growth for the general bubbles reactor and micro-nano bubbles reactor, oxygen uptake rates(OURs) in the saturated effluent of the primary clarifier were measured with the general bubbles reactor and micro-nano bubbles reactor. The OURs of in the saturated effluent of the primary clarifier with the general bubbles reactor and micro-nano bubbles reactor were 0.0294 mg O2/L․hr and 0.0465 mg O2/L․hr, respectively. The higher micro-nano bubbles reactor's oxygen transfer coefficient increases the OURs. In addition, the maximum readily biodegradable substrate utilization rates(Kms) for the general bubbles reactor and micro-nano bubbles reactor were 3.41 mg COD utilized/mg active VSS․day and 7.07 mg COD utilized/mg active VSS․day, respectively. The maximum specific biomass growth rates for heterotrophic biomass(μmax) were calculated by both values of yield for heterotrophic biomass(YH) and the maximum readily biodegradable substrate utilization rates(Kms). The values of μmax for the general bubbles reactor and micro-nano bubbles reactor were 1.62 day -1 and 3.36 day -1 , respectively. The reported results show that the micro-nano bubbles reactor increased air-liquid contact area. This method could remove dissolved organic matters and nutrients efficiently and effectively.

본 연구에서는 고비용의 실리카흄의 대체재로서 인산부산석고와 카올린을 활용한 시멘트매트릭스의 화학적, 기계적 성질에 대하여 분석하였다. 실험을 위하여 인산부산석고는 이수석고 형태인 건조석고, 반수석고, Ⅲ형 무수석고, Ⅱ형 무수석고로 실험용시료를 제조하였으며, 900℃에서 소성된 카올린은 서냉과 급냉의 형태로 제조된 메타카올린의 형태로 제조하였다. 또한 이재료를 활용하여 혼합시멘트를 제조하였으며, 제조된 시멘트를 사용하여 실리카 흄을 혼입한 시멘트 매트릭스와 재료적 성능을 비교 평가하였다. 실험결과 급냉제조된 메타카올린이 다른 재료에 비하여 성능이 우수한 것으로 분석되었다.

물유리계 그라우팅 공법은 침투주입 그라우팅으로 자주 적용되고 있으나, 시간경과에 따른 내구성 저하와 환경에 부정적 영향에 대한 문제가 부각되고 있다. 이에 마이크로시멘트계 무기질 재료의 ENG 공법이 이러한 물유리계 그라우팅 공법의 문제점을 극복하면서 우수한 침투성을 목표로 하여 개발되었다. ENG의 적용성을 파악하기 위해 체적변형시험, 용탈실험, 일축압축실험, 실내 투수실험 및 현장투수실험 그리고 중금속검출실험을 실시하였다. 그 결과 체적변형, 용탈량, 일축압축강도는 물유리 공법보다 월등히 우수하였으며, 투수실험에 있어서도 차수효과가 나타났다. 또한 중금속 검출량도 미미하여 환경에 부정적인 효과도 적을 것으로 판단된다.

The optimum design of power yacht belongs to the nonlinear constrained optimization problems. The determination of scantlings for the bow structure is a very important issue with in the whole structural design process. The derived design results are obtained by the use of real-coded micro-genetic algorithm including evaluation from Lloyd's Register small craft guideline, so that the nominal limiting stress requirement can be satisfied. In this study, the minimum volume design of bow structure on the power yacht was carried out based on the finite element analysis. The target model for optimum design and local structural analysis is the bow structure of a power yacht. The volume of bow structure and the main dimensions of structural members are chosen as an objective function and design variable, respectively. During optimization procedure, finite element analysis was performed to determine the constraint parameters at each iteration step of the optimization loop. optimization results were compared with a pre-existing design and it was possible to reduce approximately 19 percents of the total steel volume of bow structure from the previous design for the power yacht.

지표-지각환경을 구성하는 지질매체의 구조와 성질의 정량적-체계적 이해를 위한 예비연구로, 매질을 구성하는 입자의 모양, 크기, 충전 밀도가 공극 구조의 특성과 매질의 성질에 미치는 영향을 알아보기 위해 입자의 모양이 구형인 글래스 비드와 모양이 불규칙한 실리카 젤을 이용하여 입자 크기와 공극률이 서로 다른 다양한 다공성 매질을 준비하였고, 핵자기공명 현미영상을 이용하여 약 50 μm의 분해능으로 삼차원 영상을 획득하였다. 분석 결과, 지름 약 0.2~1.3 mm 크기의 입자로 구성된 다공성 매질의 비표면적은 2.5부터 9.6 mm2/mm3, 공극률은 0.21에서 0.38, 투수율은 11.6에서 892.3 D이며, 이는 일반적인 미고결 샌드가 갖는 값의 범위에 해당된다. 비표면적, 공극률, 투수율의 관계는 Kozeny 식에서 예상된 경향과 비교적 일치하였다. 상자집계 프랙탈 차원은 공극률, 비표면적과의 관련성이 높으며, 공극률이 0.29~0.38일 때 비표면적이 약 2.5부터 6.0 mm2/mm3까지 증가할수록 프랙탈 차원이 2.6에서 3.0까지 선형으로 증가하며, 공극률이 0.21~0.28일 때 비표면적이 약 2.5부터 9.6 mm2/mm3까지 증가할수록 프랙탈 차원이 2.5에서 3.0까지 선형으로 증가한다. 실제 다공성 사암에 포함된 유체의 삼차원 구조를 핵자기공명 현미영상으로 영상화하였고, 이에 대한 비표면적은 0.33 mm2/mm3, 공극률은 0.017, 투수율은 30.9 mD, 상자 집계 프랙탈 차원은 1.59로 계산되었다. 본 연구에서 제시된 것과 같이 핵자기공명 현미영상은 다양한 다공성 매질의 삼차원 공극 구조를 영상화할 수 있고, 삼차원 공극 구조에 대한 상자집계 프랙탈 차원은 본 연구에서와 같이 다양한 공극 구조에 대해 분석이 가능하며, 다공성 매질의 이동 특성을 나타내는 매개 변수들과 지진파 감쇠 등에 대한 조절 인자로 사용될 수 있을 것으로 기대된다.

In the high precision robot systems, the most popular tasks may be handling of micro-scale objects on a surface such as a micromanipulation robot system. In handling of micro-scale objects, the stiction effect becomes a fundamental issue since the micro-contact mechanics dominates the micromanipulation robot system. In the paper, a theoretical non-stick condition derived from the micro-contact mechanics is carried out for the propose of micro-scale object manipulation. To verify the non-stick condition, a micro-manipulation robot system equipped with a high precision stage system and a microscope system is developed. Experimental results show that the proposed non-stick condition guarantees successful micro-scale object manipulation.

Many lakes or irrigative reservoirs in Korea are rapidly contaminated due to the ever increasing pollutants. Although lots of treatment processes have been recommended and practiced, economical and technical improvement is currently needed. In this study, contaminated irrigation reservoir was treated using the proposed process which is consisted of fine air bubbles, coagulation and flotation. Fine bubbles, approximate diameter of 3 to 10 ㎛, were generated using cavitation in the pressurized tank and polyaluminum chloride was used as coagulants. This fine bubbles, coagulation and flotation effectively controlled the low density algae, for example, Chlorophyll-a was removed more than 97 %. Removal efficiency of COD, SS, T-N and T-P were 80.7%, 94.3%, 64.1% and 92.4%, respectively. Pollutants released from the sediments was removed more than 80% of organics and 60-70 % of nutrients. Consequently, fine bubbles coagulation and flotation process could be effectively used as an alternative treatment method for the purpose of control of lake water quality.

In this paper, a robotic system which consists of a precision manipulator and a micro gripper for a micro system assembly is presented. By the experiment, we proved that the developed the system gives acceptable performance when minute operations. Developed the micro-nano robot is actuated by newly proposed modular revolute and prismatic actuators. As an end-effector of this system, micro gripper is designed and fabricated with MEMS technology and the displacement of jaw is up to 142.8 micro meter. We think that new robot system will be appropriate for micro system assembly tasks and life science application

Rapid progress in urbanization has resulted in a change of the micro climate, especially in the urban area. In order to investigate the phenomenon of the heat island in the residential micro climate, a field survey was carried out by 4 sets of the residential type in Jeonju under typical winter synoptic condition. As analytic methode, it is used the comparison on the relation of the Land-to-Coverage Rate to Heat Island and Oxygen Concentration. And as a key question it is asked how stable characteristics of the micro climate will result from the survey of the Heat Island and the Oxygen Concentration, used as indicator. To ensure the trustworthy result of research, it is calculated the critical influence of the wind velocity and the Land-to-Covearage Rate. As a result of comparative analysis, it could be confirmed that the local temperatures in all sets of the residential type were higher than the average temperature in Jeonju. But the housing type A "exclusive use for housing zone" has relativly the most stable and best living condition. On the contrary the residential type B and D has the worst toward the oxygen concentration in the time zone 9-12 a.m., which didn't reach the minimum of the oxygen concentration 20.5%. It means that the higer the development and population density is, the worse is the situation of the Quality of Life in the residential types in accordance with the heat island and oxygon concentration.

In order to make use of the protection effect against wind by the vegetation, it examined whether it should make what vegetation form and arrangement using the 2-dimensional non-hydrostatic model. When the foliage shielding factor increases, it becomes hard to take in protection effect against wind in a residential section. When it makes height of vegetation high, it becomes hard to take in protection effect against wind with height. In the comparison in the case where vegetation high is gradually made low toward wind-stream from a vegetation, and the case of making it low gradually, although former tends to receive the protection effect against wind by the vegetation, attenuation of wind velicity becomes large. In the comparison in the case where foliage shielding factor and distribution of density of leaf are gathered gradually toward wind-stream from a vegetation. It has been understood to evaluate to height the influence that the vegetation multi-layer model by which the heat revenue and expenditure in the direction of the vegetation height is considered is used, and to characterize the vegetation group by the parameter setting.

We developed a numerical model that considered the influences on the thermal environment of vegetation, water surfaces and buildings to predict micro climatic changes in a few km2 scales; and applied this model to the Mino residential development region in Osaka Prefecture by using a nested technique. The calculated temperatures and winds in the residential development region reasonably agreed with the observed ones. We then investigated the influences on the thermal environment of the construction of a dam, the change of the green coverage rate. The results obtained from the numerical simulations were qualitatively reasonable.

Separation of strontium ion from synthetic seawater in the contained liquid membrane permeator with two micro-porous films was performed. The permeator consisted of a liquid membrane and two cells for aqueous solutions. The liquid membrane consisted of D2EHPA(di-2-ethylhexyl-phosphoric acid) and DCH18C6 (dicyclohexano-18-crown-6), diluted to 30 vol % with kerosine and was trapped between two micro-porous hydrophilic films. This liquid membrane separated two aqueous solutions, one of which was synthetic seawater and the other of which was the stripping solutions consisting of 1㏖/L H2SO4 Solution. The effects of various operating parameters on the extraction rate and equilibrium extraction ratio of strontium ion from synthetic seawater were experimentally examined. The addition of DCH18C6 to the D2EHPA solution caused synergy effect on the extraction of strontium ion. The permeator extracted strontium ion from synthetic seawater effectively with high membrane life time.

북동태평양 C-C지역의 우리나라 광구에서 산출되는 망간단괴의 내부조직을 크게 주상조직 층상대, 첨상조직 층상대, 첨상조직 괴상대, 첨상조직 다공질대 및 괴상조직 괴상대로 구분하였다. 주상조직 층상대에서는 버나다이트(vernadite)가 가장 우세하게 산출되며, 첨상조직 층상대에서는 부서라이크(buserite)가 함께 산출된다. 첨상조직 괴상대는 부서라이트의 산출이 두드러지며, 부분적으로 토도로카이트(todorokite)가 수반된다. 첨상조직 다공질대는 첨상체 또는 구상체로 이루어지며 부분적으로 괴상조직으로 교대되는데 주로 토도로카이트와 부서라이트로 구성되어 있다. 괴상조직을 갖는 괴상대에서는 토도로카이트와 버네사이트(birnessite)가 부서라이트와 함께 산출된다. 각 조직대별로 미세조직을 이루는 엽리들에 대해 전자현미분석을 실시하였다. 엽리의 화학조성을 구성하는 요인은 상관계수 군집분석에 의해 Mn-K의 Mn군, Cu-Ni-Zn-Mg(Ca-Na)의 Cu-Ni-Mg군 Fe-Co-Ti(Ca-P)의 Fe군과 Si-Al의 Si군 등 네 개군으로 구분된다. 각 조직대는 세 개 또는 네 개의 군으로 구성되며 이들 각군은 단괴에서 산출되는 광물과 밀접한 관계를 가진다. Mn군은 토도로카이트, Cu-Ni-Mg군은 부서라이트, Fe군은 함코발트수산화철광물, 그리고 Si군은 규산염광물에서 주로 기인하는 것으로 생각된다. 엽리의 화학조성은 이들 광물의 조합과 구성광물의 화학조성에 따라 지배되고 한 조직대내에서도 여러종류의 조합을 보이는데 이는 각 조직대의 엽리들의 성인과 밀접한 관련이 있는 것으로 생각된다.

For the purpose of development of a liquid membrane permeator which separates metal ions from aqueous solutions continuously and effectively, a continuous membrane permeator with the membrane solution trapped between extraction and stripping phases by two micro-porous hydrophilic films was manufactured. Experimental researches on the separation of zinc ion from aqueous solutions were performed in the liquid membrane permeator with 30 vol % D2EHPA solution in kerosine as liquid membrane. As results, the liquid membrane permeator separates zinc ion from aqueous solutions continuously and effectively in the wide range of operating conditions. A simple mass transfer rate model using equilibrium constant of the extraction reaction for the system used were proposed, and the model was compared with experimental results of separation of zinc ion in the permeator. And the effects of operating factors, such as space time, pH of extraction solution, extraction temperature, on the separation rate of zinc ion in the permeator were experimentally examined.

A recently constructed commercial ship is a complexive integrated system like a small city in which has a generator, power distributing facilities, various radio equipments and high power circuit breakers are installed. Therfore it could make a malfunction of the microprocessor in the various control units which are so important during the ocean voyage of larger ship. This paper has studied whether is properly required or not on the view of the actual electro magnetic compatibility status on the electromagnetic interference and suceptibility test requirments listed on the IACS (International Association of the Classification Society). Through these results, we are looking forward to the new suggestions of the Electro Magnetic Compatibility test in order to reduce the malfunction in the ship regarding test item, test level, and test condition.

SPME device was applied to determine the THM in an aqueous solution. The 6 kinds of THM was quantitatively detemined by using GC-ECD which has the sample extracted on the SPME fiber from an aqueous solution for 10 min. The THM components were well separated from CHCl_3 to the last CHBr_3 within 13 mans at the condition. 6 kinds of the volatile halogenated organic compounds: CHCl_3, CHBrCl_2, CHBr_2Cl, CHCl_3, C_2Cl_4, and CHBr_3, showed well defined calibration graph with good linearity from a few ppb level up to several tens of ppb concentration. CHBr_2Cl and C_2Cl_4, were detected from a few samples among the 10 of river samples. CHCl_3, however, was detected in 4 sea water samples with the highest of 10 ppb among the polluted 6 positions. Trace level of CHBr_2Cl and few ppb level of CHBr_3 were also detected at the other two sample stations. Most of the 13 rain water samples collected from 6 sampling stations were contained ppb level of CHCl_3, and also CHBr_2Cl, and C_2Cl_4 were only detected at trace level at a few rain samples among them. We could recognize the fact that our air and water environment has already been contaminated by certain volatile halogenated organic compounds through this study.