This research combines the liquid carbon precursor infiltration process for carbon/carbon composites with the fabrication procedure for organic, carbon-matrix friction materials in automotive. In the densification process, different liquid carbon precursors and numbers of densification cycle are adopted to investigate the influence on physical and mechanical properties, microstructure and tribological behavior. Experimental results indicate that the infiltration of liquid carbon precursors could improve the physical, mechanical properties and tribological performances of organic friction materials. The open porosity decreases with the number of densification cycle. Both bulk density and hardness increase with the number of densification cycle. The resin-based specimens show higher hardness and lower open porosity than those of the pitch-based specimens after each densification cycle. The tribological measurement of specimens with different carbon precursors shows that the pitch-based specimen shows lower and more stable friction coefficients and exhibits lower weight losses in comparison with other carbon precursors. Morphological observations show that a large area of smooth lubricative film was easily presented on the worn surfaces of the pitch-based specimens, whereas it was seldom observed on the worn surfaces of the preform specimen and resin-based specimens.

2017년부터 2018년까지 전북지역 오디 생산용 뽕나무에 발생하는 주요 해충의 발생 양상과 유기농업자재에 의한 뽕나무이 방제 효과를 조사하였다. 부안과 익산지역을 중심으로 수확 전 발생하는 주요 해충은 뽕나무이, 미국흰불나방, 뽕나무명나방, 노린재류, 꽃매미 6종이었으며 수확 후에는 미국흰불나방, 뽕나무명나방, 총채벌레, 미국선녀벌레, 노린재류 등 5종이 발생하였다. 또한 오디 생산용 뽕나무 재배시 가장 문제가 되는 병해충인 균핵병과 뽕나무이를 동시에 친환경적으로 관리하기 위해서는 데리스 추출물(데리스 90%) 250배와 황토유황 500배를 혼합하여 처리하는 것이 방제효과 97.6%로 효과적이었다. 선발된 유기농업자재에 효과적인 처리시기는 4월 상·중순이며, 7일 간격으로 3회 방제하면 94% 이상의 방제효과가 있고 약해도 발생하지 않아 유기농업자재를 이용한 뽕나무이의 친환경방제가 가능할 것으로 판단되었다.

As concerns about the pursuit of well-being culture and interest in safe food has increased and demand for organic agricultural products are increasing. This study was conducted to investigate the occurrence pattern of diseases and pests and to select effective organic materials for control of diseases and pests in organic watermelon. The watermelon was damaged by diseases and pests such as Didymella bryoniae, Podosphaera xanthii, Aphis gossypii, Tetranychus urticae, thrips, Spodoptera exigua, and Spodoptera litura. Among them, powdery mildew and cotton aphid are major disease and pest in organic watermelon. The occurrence of powdery mildew and cotton aphid initiated in the middle of May in Chungju and Eumseong. The control efficacy for eleven organic materials against powdery mildew was evaluated. As the results, the symptoms of plant disease were effectively reduced by more than 85% in the treatments of materials such as sodium bicarbonate 80% and sulfur 80%. The treatment of TFM-6 (insect repellent 2%+paraffin oil 68%) and TFM-7(cinnamomum ext. 10%+derris ext. 20% + citranella oil 30%) showed by more than 80% in control efficiency against cotton aphid. Tstudy was supported by the research project of RDA.(Project No.: PJ0125302018)

To abate the problem of odor from restaurants, a hybrid adsorbent consisting of organic and inorganic materials was developed and evaluated using acetaldehyde as a model compound was deveioped and evaluated. Powders of activated carbon, bentonite, and calcium hydroxide were mixed and calcinated to form adsorbent structure. The surface area of the hybrid adsorbent was smaller than that of high-quality activated carbon, but its microscopic image showed that contours and pores were developed on its surface. To determine its adsorption capacity, both batch isotherm and continuous flow column experiments were performed, and these results were compared with those using commercially available activated carbon. The isotherm tests showed that the hybrid adsorbent had a capacity 40 times higher than that of the activated carbon. In addition, the column experiments revealed that breakthrough time of the hybrid adsorbent was 2.5 times longer than that of the activated carbon. These experimental results were fitted to numerical simulations by using a homogeneous surface diffusion model (HSDM); the model estimated that the hybrid adsorbent might be able to remove acetaldehyde at a concentration of 40 ppm for a 5-month period. Since various odor compounds are commonly emitted as a mixture when meat is barbecued, it is necessary to conduct a series of experiments and HSDM simulations under various conditions to obtain design parameters for a full-scale device using the hybrid adsorbent.

PURPOSES : The objective of this study is to evaluate the performance of combined organic and inorganic hybrid mortar used as repair materials (UM mortar) for concrete road facilities by comparison with cement repair materials (RM mortar). METHODS: In order to produce UM mortar, four different levels of inorganic materials were adopted and the ratio of main resin to hardener was fixed at 1:2. For comparison, RM mortar made with cement repair materials was also produced. Fluidity, strength characteristics, length change, and freezing-thawing resistance of the mortars were measured at the predetermined periods. In addition, the microstructures of the mortars was performed on the 28-day mortar samples to examine the properties of the interfacial transition zone (ITZ). RESULTS : It was observed that the mechanical properties, except for compressive strength, and freezing-thawing resistance of UM mortars were much better than those of RM mortar. Furthermore, showing a densified ITZ properties on the UM mortars from the microstructural observation, the usage of UM mortars exhibited a beneficial effect on the enhancement of mortar properties. CONCLUSIONS: It is concluded that the application of combined organic and inorganic hybrid mortars is a possible option for the repair of deteriorated concrete road facilities.

유기농경지에서 문제가 되는 해충을 방제하기 위하여 농가에서는 식물추출물 등 다양한 자가제조 유기농업자재를 활용하고 있다. 본 연구에서는 농가 자가제조 유기농업자재를 이용하여 목화진딧물(Aphis gossypii)과 꽃노랑총채벌레(Franklineilla occidentalis)에 대한 살충효과를 시험하였다. 유기농업자재는 유기재배 농가에서 직접 수집하였으며 식물추출물로는 마늘, 돼지감자, 은행잎 등의 식물추출물과 목초액, 식물오일 등 8종의 자재를 이용하였다. 해충에 대한 살충시험은 25℃, 60% 습도 조건의 곤충사육실에서 이루어졌다. 처리시험을 위해 오이절편을 페트리디쉬에 넣고 시험곤충을 접종하여 농가수집자재를 원액, 30배, 100배, 300배로 희석하여 충체 살포법으로 처리하였다. 처리 후 24시간, 36시간, 72시간 후 사충률을 조사하였다. 진딧물의 경우 100배 희석처리에서 약초액비가 75%, 유화오일이 62.5% 은행잎액비가 42.5%의 살충효과를 각각 보여주었다. 꽃노랑총채벌레에는 협죽도와 마늘이 94.7%와 88.0% 살충효과를 보여주었다.

New three emitting compounds, AK-1, AK-2 and AK-3 including diazocine moiety were synthesized through Suzuki-coupling reaction. Physical properties such as optical, electroluminescent properties were investigated. UV-visible spectrum of AK-1, AK-2 and AK-3 in film state showed maximum 392, 393 and 401 nm. PL spectrum of AK-1, AK-2 and AK-3 showed maximum emission wavelength of 472, 473 and 435 nm. Three compounds were used as EML in OLED device: ITO/2-TNATA (60 nm)/NPB (15 nm)/EML (35 nm)/Alq3 (20 nm)/LiF (1 nm)/Al (200 nm). AK-3 OLED device showed C.I.E value of (0.18, 0.26) and luminance efficiency of 0.51 cd/A at 10 mA/cm2. New derivatives including diazocine moiety were introduced as OLED emitting material and the EL efficiency was increased by the proper combination of core and side group.

The comstock mealybugs had been occurred at a Muscat of Alexandria’ organic vineyard in Okcheon. They had beenfound in the vines’s trunk since mid-June and moved to cane and leaves since early July, and also had been found ingrape clusters since late-July. The number of comstock mealybug and the grape’s fruit damage in Eco-friendly vineyardswere higher than in conventional culture vineyard. And the marketability of green variety grape was more damaged fromcomstock mealybug than the black variety grape. Toxicities of 8 organic agricultural materials(OAM) were evaluated tocomstock mealybug at the recommended concentration. As a results, Lightyellow sophora and Derris extracts exhibitedstrong insecticidal activity with 100% mortality. When the Lightyellow sophora extract was uniformly distributed on thevine from early-July to mid-July, commercial grapes could be harvested. Therefore, I thought that we can control comstockmealybug by spraying OAM in a timely period.

This study was carried out to elucidate suppressive effect of loess-sulfur complex and neem oil on the development of leaf mold and fungus gnat in no-pesticide tomato farming system. Since tomato leaf mold occurred 15%, neem oil, loess-sulfur mixture and boscalid(47%, water soluble chemicals) 2,000 times, 1,000 times and 2000 times diluted was treated three times, respectively. When disease incidence of tomato leaf mold was investigated 20 days after final treatment, it was recorded 17% in neem oil treatment(control efficacy 40%) and 12.3% in loess-sulfur mixture treatment(control efficacy 59%). Among three control agents used, Boscalid(47%, water soluble chemicals) showed the best control effect against tomato leaf mold. When neem oil was diluted 250 times, 330 times and 500 times and treated in coir bag infected with fungus gnat, its control values was 69, 59, and 55%, respectively. There was no significant difference among three treatments. As a result, 500-fold diluted neem oil treatment is considered a good measure to control fungus gnat in the field condition.

There has been growing concern over the emissions of formaldehyde and VOCs from automotive interior materials, as these could have an important impact on the in-vehicle air quality (IVAQ) of automotive vehicles. Odor along with VOCs refers to the automotive interior smell emitted directly or indirectly from any part of an automotive interior, based on human olfactory senses and a comfort evaluation of vehicle quality. The objective of this paper is to compare the odor intensity using GC/MS analysis method and odor sensory test in accordance with ISO 12219-2. For the compounds having low odor threshold value and high VOC concentration, it was found that there was the same tendency in each field of odor whether the instrument analysis method or the odor sensory test method was used.

탄소섬유 한외여과막 및 광촉매 혼성 수처리를 위해 관형 여과막 외부와 원통형 막 모듈 내부 사이 공간에 광촉매를 충전하였다. 광촉매는 PP (polypropylene) 구에 이산화티타늄 분말을 플라즈마 화학증착 공정으로 코팅한 것이다. 휴믹산과 카올린 모사용액을 대상으로 막오염을 최소화하기 위해 10분 주기로 10초 동안 물 역세척을 시행하였다. 기존 결과와 동일하게 휴믹산을 10 mg/L부터 2 mg/L로 변화시킴에 따라, 막오염에 의한 저항 (Rf)이 감소하여 2 mg/L에서 최대 총여과부피 (VT)를 얻었다. 탁도와 휴믹산의 처리효율은 각각 97.1%와 74.2% 이상으로 휴믹산 농도의 영향을 받지 않았다. 그러나 기존 결과에서는 휴믹산의 농도가 증가할수록 휴믹산의 처리효율이 다소 증가하는 경향을 나타냈다.

탄소 한외여과막 및 광촉매 혼성 수처리를 위해 관형 여과막 외부와 원통형 막 모듈 내부 사이 공간에 광촉매를 충전하였다. 광촉매는 PP (polypropylene) 구에 이산화티타늄 분말을 플라즈마 화학증착 공정으로 코팅한 것이다. 휴믹산과 카올린 모사용액을 대상으로 막오염을 최소화하기 위해 10분 주기로 10초 동안 물 역세척을 시행하였다. 기존 결과와 동일하게 휴믹산을 10 mg/L부터 2 mg/L로 변화시킴에 따라, 막오염에 의한 저항(Rf)이 감소하여 2 mg/L에서 최대 총여과부피 (VT)를 얻었다. 탁도와 휴믹산의 처리효율은 각각 98.9%와 88.7% 이상이었다. UF 및 UF + TiO2, UF + TiO2 + UV 공정의 처리 분율 결과, 광촉매 흡착과 광산화에 의해 탁도는 거의 처리되지 않았으나, 광촉매 흡착 및 광산화에 의한 휴믹산 처리 분율은 각각 2.5%, 12.3%이었다. 기존 결과와 비교하면, 분리막의 재질과 기공의 크기에 따라 광촉매 흡착과 광산화에 의한 휴믹산의 처리 분율이 다르게 나타났다. 공정이 단순화될수록 180분 운전 후 막오염 저항(Rf,180)은 증가하였고, 최종 투과선속(J180)은 소폭 감소하였다.

유기농업에 자주 이용되는 축분퇴비와 작물잔사를 이용하여 질소무기화율을 추정하기 위한 항온실험을 수행하였다. 순무기화량은 유기자재 처리시 토양중 무기화된 질소(NH4-N + NO3-N)에서유기자재를 처리하지 않은 토양의 무기화된 질소량을 빼서 계산하였다. 담수 조건(논토양조건)에서 용출법을 이용하여 25oC에서 0, 1, 2, 3, 4, 6, 8, 16, 21주차에 무기화량을 조사하였다. 담수조건의 토양에 유기자재를 혼합한 후 지속적으로 물로 무기화된 질소를 용출하고 용출된 무기질소의 합을 이용한 무기화량을 추정하였다. 투입된 자재는 옥수수잔사, 알팔파, 수단그라스, 수수, 들깨잔사, 볏짚, 배추, 별꽃, 네마장황, 퇴비I, 퇴비II, 퇴비III, 유박, 토마토잔사, 수박잔사, 피마자박, 요소 이었고, 수행된 결과를 요약하면 다음과 같다. 1. 알팔파는 가장 높은 질소용출량을 나타내었다. 2. 자재 투입으로 토양 중 질산태 질소는 축적되지 않았다. 3. 침출수 중 암모니아태 질소의 누적량은 대부분의 유기자재에서 탄질비가 낮을수록 높은 무기화량을 보였다. 4. 볏짚과 퇴비I과 II를 제외한 대부분의 유기자재는 인산의 무기화를 증가시키지는 못하였다.

본 연구는 탄소 : 질소(탄질)비가 다른 유기자재를 시용하였을 때 시기별 양분의 동태와 유기재배 수수*수단그라스의 비료이용율에 미치는 영향을 조사하였다. 처리구는 질소함량 210kg/ha 수준으로 축분퇴비, 알팔파, 유박, 화학비료를 포함하였다. 유박과 알팔파는 가장 낮은 탄질비를 나타내었고 축분퇴비는 33.7 : 1의 가장 높은 탄질비를 보였다. 축분퇴비는 시용량이 가장 많았고 이에 따라 토양내 양분농도를 증가시켰다. 탄질비가 낮은 유박과 알팔파는 축분퇴비에 비해서 질소의 무기화율을 촉진시켰다. 질소이용효율은 화학비료구에 비해서 알팔파와 유박이 약 60% 전후를 나타내었고, 축분퇴비는 20% 이하의 효율이 관찰되었다. 인산의 이용효율은 알팔파가 가장 높았고 축분퇴비가 가장 낮았다. 이에 따라 탄질비를 고려한 유기자재를 선택해서 밭토양에 시비를 해야 할 것으로 판단되었다.