To evaluate system reliability of a composite structure consisting of more than two structural members, it is necessary to identify that the members are connected to each others in parallel or in serial. Especially for parallel composite system, it is also necessary to confirm that mechanical properties of materials for the members are brittle or ductile. For parallel system of brittle materials, if one part fails, that part cannot resist load anymore and the whole load transfers to the other part. However, for parallel system of perfectly plastic materials, if one part fails, that part can maintain the amount of its maximum load capacity and the remaining load transfers to the other part. In this study, a methodology to determine reliability index for composite structures consisting of quasi-brittle materials. By assuming quasi-brittle materials as brittle or perfectly plastic materials, the upper and lower bounds of the reliability index can be determined. The reliability index for parallel system of quasi-brittle materials is then determined by interpolating the upper and lower bounds indices using ductility number extracted from stress-strain curves of quasi-brittle materials.

In this study, a real-scale specimen of Steel-Confined Prestressed Concrete (SCP) composite girder was tested in a three points bending. Furthermore, vibration tests were performed to verify the dynamic stability of the SCP composite girder for railway bridges. The results of the experimental test were similar to stable rigidity behavior until the static actuator limit load (6300 kN). That is, the SCP composite girder showed a stable rigidity behavior in the ultimate load (3,174 kN) as well as the service load (1,076 kN). Finally, the possibility of resonance of the SCP composite girder has been found to be low.

These days, the Composite Slabs with Deep deck plate was commonly used in domestic construction site, and, the application of the Slim Floor system was increased from the Enlargement and High-rise Building. But, Slim Floor system using the deep deck was shown safety problem caused by the deflection and local buckling in construction phase when used to more than 6m. Therefore, for solving the problem, the installation of the shores is essential. This study is realize the long span slab without shores from control the deflection through applied the pre-tensioning elements in cap deck. In addition, by applying the pre-tensioning member as the tensile member of the Cap Deck composite slab, the pre-tensioning member for the shores tries to be used as the structural member. Accordingly, to determine the flexural performance of the Cap deck composite slab through the pre-tensioning force in tensile member, and, the composite effect of the cap deck composite slab by the experiments.

Vegetable leather 표면 코팅에 사용된 폴리우레탄 수지는 glycerol의 함유를 mole% 비로 달 리하면서 합성하였다. 합성된 폴리우레탄 수지의 기계적 특성은 SEM, FT-IR, UTM 등을 이용하여 측 정하였다. 친환경적인 고분자 수지의 관심이 고조됨에 따라 용제의 사용을 최소화한 vegetable leather 코팅에 사용되는 수분산 수지를 합성하였다. 지방족 3가 알콜인 glycerol의 mole% 비가 증가함에 따라 내마모도, 인장강도가 증가함을 알 수 있었다. 반대로 연신율, 내굴곡 물성은 감소함을 알 수 있었다. Toluene을 이용한 내용제성 물성측정 결과에는 glycerol의 mole% 증가에 따른 물성 증감 효과는 없었 다.

고급지방산 메틸 에스테르류의 소포제를 합성하고 FT-IR과 1H-NMR 분석을 통해 확인하였 다. FT-IR을 이용하여 합성된 물질의 특징인 -C=O기는 1740 cm-1 부근에서, 그리고 C-O기는 1175 cm-1 피크 값을 가지는 것을 확인하였다. 또한 1H-NMR 분석을 통해 에스테르의 -C=O의 Chemical shift가 2.29 ppm에서 나타나는 것을 확인하였다. 표면장력은 Surface Tensiometer CBVP-43을 이용하여 측정하였다. 표면장력은 17.7에서 21 dyne/cm 값을 가진다. SLS 수용액에서의 소포능은 Ross-Miles법을 통해 측정되었다. 4종류의 소포제 중 소포능 은 스테아르산메틸을 이용하여 제조한 소포제가 가장 뛰어난 것으로 측정됐다.

Other countries(USA, Europe) have performed the fire resistance design of buildings by the alternative performance design methods, which are based on fire engineering theories. However, in Korea, the process on the alternative fire resistance performance design has only suggested without any applications for real steel structures. Therefore, In the case of steel structures stagnant research on refractory measures face difficulties in introducing fire resistance design. In this study, first of all, Intumescent paint was analyze the thermal properties(thermal conductivity, specific heat and density). In Sequence, using the section factor by H-standard section propose of section concrete filled steel tube and hollow. finally presents a reasonable thickness Intumescent paint takes time to target performance of the proposed cross-section steel tube.

Chrysene 및 Pyrene 유도체를 합성하였고, 열적 안정성은 phenanthrene기를 도입한 BC6이 mp: 406oC 이었다. 용액상태에서 Host-Dopant 시스템으로 각각의 분광특성을 측정하여 NP5-BC1, NP5-BC5 system이 우수한 결과를 얻을 수 있었고, 이들의 밴드갭은 3.04, 2.66, 2.67eV 이었다.

This study presents the design and implementation of a structural health monitoring system based on acceleration measurements which used to observe and investigate the structural performance of the administration building in Seoul National University of Education during an earthquake event. The frequency and spectrum are analyzed to assess the building performance during an earthquake shaking which took place on March 31st, 2014. The results indicate that : the vibration of the roof is more clear and dominant during the shaking, and the response of building during earthquake is so small and safe.

The numerical study of laminar syngas-fuel/air mixture with 10% hydrogen content impinging plate was conducted. Effects of impinging distance, Reynolds number and equivalence ratio were major parameters on combustion and emission for stagnation point. The numerical result calculated by SPIN application of the CHEMKIN software. There result showed the following : The Peak point of the axial velocity, the flame temperature and CH reaction were appeared in tip of the inner reaction zone. The emission results in impinging flame of syngas fuel show that the characteristics of NOx emission traced well with adiabatic temperature trend and CO emission due to fuel rich condition increased continuously with respect to the equivalence ratio.

In this study, cobalt nanopowder is fabricated by sonochemical polyol synthesis and magnetic separation method. First, sonochemical polyol synthesis is carried out at 220oC for up to 120 minutes in diethylene glycol (C4H10O3). As a result, when sonochemical polyol synthesis is performed for 50 minutes, most of the cobalt precursor (Co(OH)2) is reduced to spherical cobalt nanopowder of approximately 100 nm. In particular, aggregation and growth of cobalt particles are effectively suppressed as compared to common polyol synthesis. Furthermore, in order to obtain finer cobalt nanopowder, magnetic separation method using magnetic property of cobalt is introduced at an early reduction stage of sonochemical polyol synthesis when cobalt and cobalt precursor coexist. Finally, spherical cobalt nanopowder having an average particle size of 22 nm is successfully separated.

NiAl2O4 nanoparticle was synthesized by a reverse micelle processing for inorganic pigment. N (NO3)2·6H2O and Al(NO3)3·9H2O were used for the precursor in order to synthesize NiAl2O4 nanoparticles. The aqueous solution, which consisted of a mixing molar ratio of Ni/Al, was 1:2 and heat treated at 800~1100 oC for 2h. The average size and distribution of synthesized NiAl2O4 powders are in the range of 10-20 nm and narrow, respectively. The average size of the synthesized NiAl2O4 powders increased with an increasing water-to-surfactant molar ratio and heating temperature. The crystallinity of synthesized NiAl2O4 powder increased with an increasing heating temperature. The synthesized NiAl2O4 powders were characterized by X-ray diffraction analysis(XRD), a field emission scanning electron microscop (FE-SEM), and a color spectrophotometer. The properties of synthesized powders were affected as a function such as a molar ratio and heating temperature. Results indicate that synthesis using a reverse miclle processing is a favorable process to obtain NiAl2O4 spinels at low temperatures. The procedure performed suggests that this new synthesis route for producing these oxides has the advantage of being fast and simple. Colorimetric coordinates indicate that the pigments obtained exhibit blue colors.

본 연구에서는 메탄 대향류 확산 화염내 탄소나노튜브의 합성에 대하여 실험 및 수치적 연구를 수행하였다. 아세틸렌을 일정비율로 메탄에 혼합하여 연료 가스로 사용하였으며, 탄소나노튜브의 합성을 위한 촉매로서 페로센이 이용되었다. 주요 인자로는 메탄 연료에 대한 아세틸렌의 혼합비율이며, 2 %, 6 %, 10 %로 혼합하였다. 탄소나노튜브를 채취한 그리드 위의 탄소나노튜브 합성 특성은 SEM 이미지로 분석되었다. 수치해석에서 화학반응 메카니즘으로는 GRI-Mech 3.0 이 적용되었다. 수치결과로는 아세틸렌 혼합 비율이 증가할수록 화염 온도도 증가하며 CO 몰분율도 증가하는 것을 알 수 있다. 실험결과로는 2% 아세틸렌 혼합 화염이 6 % 및 10 % 혼합 화염과 비교해 탄소나노튜브 합성이 잘 이루어졌음을 알 수 있었다. 이것은 6 % 및 10 % 아세틸렌 혼합화염의 경우 과도한 카본 소스의 생성이 발생해 오히려 화염 내 카본소스가 촉매입자로의 공급을 방해하기 때문이라 생각한다. 이 결과로부터 양호한 질의 탄소나노튜브 생성을 위해서는 적정한 양의 카본소스가 생성되어야 한다는 것을 알 수 있었다.

Eu2+/Dy3+-doped Sr2MgSi2O7 powders were synthesized using a solid-state reaction method with flux (NH4Cl). Thebroad photoluminescence (PL) excitation spectra of Sr2MgSi2O7:Eu2+ were assigned to the 4f7-4f65d transition of the Eu2+ ions,showing strong intensities in the range of 375 to 425nm. A single emission band was observed at 470nm, which was the resultof two overlapping subbands at 468 and 507nm owing to Eu(I) and Eu(II) sites. The strongest emission intensity ofSr2MgSi2O7:Eu2+ was obtained at the Eu concentration of 3mol%. This concentration quenching mechanism was attributableto dipole-dipole interaction. The Ba2+ substitution for Sr2+ caused a blue-shift of the emission band; this behavior was discussedby considering the differences in ionic size and covalence between Ba2+ and Sr2+. The effects of the Eu/Dy ratios on thephosphorescence of Sr2MgSi2O7:Eu2+/Dy3+ were investigated by measuring the decay time; the longest afterglow was obtainedfor 0.01Eu2+/0.03Dy3+.

NATM의 미세 구조는 SEM, FT-IR, 인장특성, 그리고 [NCO]/[OH]의 mole %, 입도분석에 의해 측정하였다. 친환경적인 NATM에 관한 관심이 고조됨에 따라 스테인레스 등의 금속코팅에 더욱더 중요한 무용제 도료의 발전을 이끈다. 우리는 스테인레스 스틸의 부식을 방지할 수 있는 NATM(New Austria Tunnel Method)의 수지를 합성하였다. 폴리우레탄과 에폭시로 합성한 혼성 수지는 일반적 NATM 수지와 도료와 비교하여 강도와 내구력이 매우 양호하다. 혼성수지는 폴리올, 에폭시, MDI, 실리콘 계면활성제, 촉매, 가교제, 충전제로 구성된다. 충전제인 fume silica는 경화속도를 가속시킬 뿐만 아니라 열적 장벽으로 물성이 우수함을 나타냈다. NATM 수지의 기계적 특성은 [NCO]/[OH]의 mole%와 fume silica가 증가함에 따라 강도가 증가하였다. 결론적으로 가교제와 fume silica가 함유된 혼성수지의 미세구조는 스테인레스 스틸같은 금속물질의 열경화코팅을 위한 좋은 물질이다.

In this study, we synthesize silica-core gold-satellite nanoparticles (SGNPs) for the surface-enhanced Raman scattering (SERS) based sensing applications. They consist of gold satellite nanoparticles (AuNPs) fixed on the silica core nanoparticles, which sizes of AuNPs can be tunned by varying the amount of reactants (growth solution and reducing agent). Their surface plasmon resonance (SPR) properties were characterized by using UV-vis spectroscopy, showing that the growth of AuNPs on silica cores leads to the light absorption in the longer wavelength region. Furthermore, the size increase of AuNPs exhibited the dramatic change in SERS activity due to the formation of hot spots. The optimized SGNPs showing enhancement factor ~3.8x106 exhibited a detection limit of rhodamine 6G (R6G) as low as 10-8M. These findings suggest the importance of size control of SGNPs and their SPR properties to develop highly efficient SERS sensors.

To improve the noise and vibration problems of the existing public parking systems, new floor system was proposed. This system consists of the Sandwich Plate System(SPS), steel beam and post-tensioned steel tendons. To verify the dynamic characteristics such as the natural frequency and damping ratio of the system, the free vibration test was performed. Test results showed that the natural frequency of the SPS composite beam was 23.8Hz and it was increased by 3.8% by installing the post-tensioned tendons. The damping ratio of the specimen with tendons was about 1.64%.

Anthraquinone 구조의 1,5- 위치와 1,8- 위치에 aromatic amino기의 변화에 따른 최대흡수파장에 미치는 영향을 알아보기 위해 1,5-dichloroanthraquinone, 1,8-dichloroanthraquinone에 각각 aniline, 2-aminobenzothiazole, 1-aminonaphthalene을 도입한 화합물 a1, b1, a2, b2, a3, b3을 합성하였다. 합성된 aromatic diaminoanthraquinone 화합물의 분광특성 뿐만 아니라 용해도 특성 및 열적 안정성을 분석하였다. 최대흡수파장을 비교하면 a1, b1에 비해 a2, b2는 파장의 변화가 없었고, a3, b3은 10 nm 이하의 장파장 이동을 보인다. 이것으로 amino기의 변화에 따른 최대흡수파장에 미치는 영향은 크지 않다는 것을 알 수 있다.

Hydrophilic SiO2 layers were obtained by the atmospheric-pressure plasma treatment. Superhydrophobic SiO2 layers were first deposited by the electrospray deposition method. The electrospunable solution that was prepared based on the solgel method was sprayed on Si (100) substrates. The surface of the electrosprayed SiO2 layers consisted of the agglomeration of nano-sized grains, which led to a very high roughness and revealed a very high contact angle to water droplets over 162˚. After having been exposed to the atmospheric Ar/O2 plasma, the observed superhydrophobicity of the SiO2 layers were greatly changed: a dramatic variation of the water contact angle from 162˚ to 3˚, namely realization of superhydrophillicity. Interestingly, the surface microstructure was almost preserved. According to the XPS analysis, it is more likely that thanks to the plasma exposure, the surface of SiO2 layers will be cleaned in terms of organic species that are hydrophobic-inducing, consequently leading to the hydrophilic nature observed for the plasma-exposed SiO2 layers.

To synthesize Sn nanoparticles (NPs) less than 30 nm in diameter, a modified polyol process was conducted at room temperature using a reducing agent, and the effects of different pH values of the initial solutions on the morphology and size of the synthesized Sn NPs were analyzed. tin(II) 2-ethylhexanoate, diethylene glycol, sodium borohydride, polyvinyl pyrrolidone (PVP), and sodium hydroxide were used as a precursor, reaction medium, reducing agent, capping agent, and pH adjusting agent, respectively. It was found by transmission electron microscopy that the morphology of the synthesized Sn NPs varied according to the pH of the initial solution. Moreover, while the size decreased to 11.32 nm with an increase up to 11.66 of the pH value, the size increased rapidly to 39.25 nm with an increase to 12.69. The pH increase up to 11.66 dominantly promoted generation of electrons and increased the amount of initial nucleation in the solution, finally inducing the reduced-size of the Sn particles. However, the additional increase of pH dominantly induced a decrease of PVP by neutralization, which resulted in acceleration of the agglomeration by collisions between particles.