This study was carried out to investigate of the combustion characteristics for the waste edible-oil and heavy oil on hot air heater. There was highly reduction in energy cost using by the hot air heater. The hot air heater to study with duct connector type, and the motor output was 2.2kW. The experimental factors for performance test, fan speed ranged from 1700 rpm to 1800rpm, and SFC, efficiency, exhaust gas emissions, and noise were measured. The results obtained were as follows; efficiency were increased to 87% at the heavy oil and was decreased to 79% on the waste edible-oil. The fuel consumption was decreased to 25L/h at the heavy oil and CO2 emissions was decreased in the case of the heavy oil

The combustion reaction of polyvinylchloride(PVC) was investigated using a thermogravimetric technique under an air atmosphere condition at several heating rates from 10 to 50℃/min. To obtain information on the kinetic parameters, the dynamic thermogravimetric analysis curve and its derivative were analyzed by a variety of analytical methods such as Kissinger, Friedman, Chatterjee-Conrad, Ozawa and Coats-Redfern methods. The combustion reaction of PVC proceeded in two steps; the first step was caused by the dehydrochlorination process in PVC, and the second step by the combustion of polyene. The comparative works for the kinetic results obtained from various methods should be performed to determine the kinetic parameters, because there are tremendous differences in the calculated kinetic parameters depending upon the mathematical method taken in the analysis.

In this study, the potential possibility of oxygenates on butyl ether(below BE) was investigated as an combustion activator for a direct injection diesel engine. It tested to estimate change of engine performance and exhaust emission characteristics for the diesel fuel and oxygenates additives blended fuel which has four kinds of blended ratio. The smoke of blended fuel(diesel fuel 80vol-%+BE 20vol-%) was reduced in comparison with diesel fuel, that is, it was reduced approximately 26%. And, power, torque and brake specific fuel consumption(BSFC) didn't have no large differences. But, NOx of BE blended fuel was increased compared with diesel fuel.

There are increased in using the bio-ethanol, as the carbon neutral attracts many researchers due to a reduction in carbon dioxide spotted as the global warming gas. A gasoline engine with 100% of the bioethanol was developed and used in Brazil already, but researches of using the bio-ethanol in diesel engines are lack. In this study, combustion tests with blend fuel of the gas oil and bio ethanol by 50% maximally due to a low cetane number of bio-ethanol were accomplished as a basic study of introduction of using the bioethanol in diesel engines. The result was that smoke emission was decreased with increase in proportion of the bio-ethanol, due to the increase of a amount of pre-mixed combustion with ignition delay. Although the amount of CO2 is reduced according as the bio-ethanol is used(carbon neutral), the emission of CO2 with increase in the proportion of the bio-ethanol was more increased due to lower a heat value of bio-ethanol than gas oil.

The combustion reaction of polypropylene was investigated using a thermogravimetric technique under an air atmosphere condition at several heating rates from 10 to 50℃/min. To obtain information on the kinetic parameters, the dynamic thermogravimetric analysis curve and its derivative were analyzed by a variety of analytical methods such as Kissinger, Friedman, Freeman-Carroll, Chatterjee-Conrad, Ozawa and Coats-Redfern methods. The comparative works for the kinetic results obtained from various methods should be performed to determine the kinetic parameters, because there are tremendous differences in the calculated kinetic parameters depending upon the mathematical method taken in the analysis.

This work was performed to investigate the distribution of the fuel droplet size around the bluff-body and the combustion characteristics. The geometry of the bluff-body influenced the spray shape and the combustion characteristics. Diameters of the bluff-body in this experiment are 6, 8, and 10mm and the impingement angles( θ) are 30°, 60°, and 90°. The measurement points were at the distances of 20 and 30mm axially from the nozzle. The SMD and Rosin-Rammler distribution was acquired by image processing technique(PMAS), and the mean temperatures were measured by thermocouple. The results obtained are as follows; In the condition of θ=60°, the values of SMD are not greatly varied compared to the other conditions. As the impingement angle of bluff-body was increased, the high temperature region was wider along radial direction. When the air-fuel ratio was increased, the CO concentration was decreased.

The characteristics of fluidized bed catalytic combustion for sludge treatment have been studied in a pilot scale of fluidized bed combustor. 1.0wt% Pt of catalyst supported on the spherical alumina was mixed with the spherical pure alumina as a bed material. Sewage sludge, heating value of which is 3,440 kcal/kg, was used as a waste sample in the experiment. Through the experiments, the various characteristics such as a bed temperature profile and flue gas(CO, SO2) concentration profile were investigated and the catalyst mixing ratio and sample feed rate were applied as experimental parameters. The experimental results showed that bed temperature was maintained more highly and flue gas concentration decreased with the increase of the catalyst mixing ratio, and bed temperature was maintained more highly also and flue gas concentration increased with the increase of the sample feed rate. The combustion efficiency of fluidized bed catalytic combustion of the sludge increased with the increase of the catalyst mixing ratio and sample feed rate and reached more than 96%.

The combustion characteristics, ignition delay, p-t, dp/dt, Q-t of diesel oil and fish oil blended diesel oils was investigated according to pressure and temperature in a constant volume combustion bomb. The results are as follows: 1) The influence of temperature and pressure on the ignition delay was almost constant in high temperature, regardless of the blending rates, and the ignition delay was shortest in the 60% blend. 2) The maximum pressure was high in order of with pure diesel oil, with the 20% blend and the 60% blend. 3) The rate of pressure rise was high in order of with pure diesel oil, with the 20% blend and the 60% blend. The rate of maximum pressure rise was significantly higher with pure diesel oil than with two blends. 4) The amount of accumulative heat release was large in order of with pure diesel oil, with the 20% blend and the 60% blend.

국산 소형어선용 예연소실식 디젤기관의 연료유를 가열할 경우, 연소특성 및 기관성능에 미치는 영향에 관하여 실험한 결과를 요약하면 다음과 같다. 1) 연료유 분사시작점은 연료유 가열온도의 증가에 따라 늦어지는 경향을 나타냈으며, 특히 저부하 운전시 늦어지는 경향이 현저했다. 2) 연소최고압력점은 연료유 가열온도의 증가에 따라 늦어졌으며, 연소최고압력은 연료유 가열온도 증가에 따라 감소하였으나 부하의 증가에 따라 증가하는 경향을 나타내었다. 3) 연료소비율은 부하의 증가에 따라 감소하였으며, 연료소비율이 가장 작은 연료유의 최적가열온도는 150℃부근임을 나타내고 있다. 4) 그을음농도는 부하와 연료유 가열온도의 증가에 따라 증가하는 경향을 나타냈다.

In this study, the combustion characteristics were investigated based on the biodrying solid recovered fuel (SRF) in a 5 Ton/day scale combustion boiler. The composition of the combustion gas containing the biodrying SRF was analyzed, the particulate matter, and its HCl content was determined with the air pollutant process test method. Mass balance, carbon balance, and combustion efficiency were calculated according to the equivalence ratio (ER) method; the energy recovery efficiency of the combustion boiler was also analyzed. The overall combustion efficiency of the biodrying SRF was 97.3 % and the energy recovery efficiency was 80.2%.

In the case of solid refuse fuel manufacturing facilities, residues, which are left-over from the process, are buried at a rate of 34% of incoming amount, and some are disposed of by combustion. The residues were upgraded by mechanical biological treatment and subject to attempts at combustion, and the bottom ash generated from combustion tests was applied to fabricate bricks for recycling. The brick was manufactured by substitutions of stone powder, cement, sand ranging from by 3 to 30% according to experimental conditions. These could be used as an interlocking block for the sidewalk or open spaces. The basic characteristics of the bottom ash and the water absorption, bending strength, compressive strength, and dimensions of the mixed bricks were tested. Results showed that 10% of the stone powder substitution was regarded as an optimal condition, and the brick quality was satisfactory under given standards, because the pozzolanic and hydration reactions occurred effectively.

By the end of 2012, the recycled proportion of domestic waste tires was 287,330 ton (93.9%) of the amount of waste tires discharged (305,877 ton). The waste tires have been reused for heat supply, material recycling and other purposes; the proportions are 50.1%, 20.7% and 23.1%, respectively. In the case of heat supply, waste tires are supplied to cement kiln (104,105 ton, 68%), RDF manufacture facilities (47,530 ton, 31%) and incinerators (1,923 ton, 1%). Recently, there has been an increase in the use of waste tires at power generation facilities as an auxiliary fuel. Thus, physico-chemical analysis, such as proximate analysis, elemental analysis and calorific value analysis have been carried out to evaluate potential of waste tires as an auxiliary fuel in Korea. The LHV (Lower Heating Value) of waste tires is approximately 20% higher than that of coal, at an average of 8,489 kcal/kg (7,684 ~ 10,040 kcal/kg). Meanwhile, the sulfur content is approximately 1.5wt. %, and balance of plant (e.g. pipe line, boiler tube, etc.) may be corroded by the sulfur. However, this can be prevented by construction and supplementation with refractories. In this study, TDF (Tire Derived Fuel) produced from waste tires was co-combusted with coal, and applied to the CFB (Circulating Fluidized Bed) boiler, a commercial plant of 100 tons/day in Korea. It was combined with coal, ranging from 0 to 20wt. %. In order to determine the effect on human health and the environment, gas emission such as dioxin, NOx, SOx and so on, were continuously analyzed and monitored as well as the oxygen and carbon monoxide levels to check operational issues.

생활폐기물 및 산업폐기물로부터 고형연료를 제조하는 과정에서 폐기물 반입량 대비 30 ~ 45%의 비율로 잔재물이 발생되어 매립되거나 일부는 소각장으로 반입되어 처리되고 있다. 이러한 잔재물은 함수율 40% 이상을 나타내어 그대로 매립되었을 경우 오염부하를 증가시킬 수 있으며, 매립에 의한 처분비용으로 전체 시설 운영비의 약 20%가 요구되는 실정이다. 이러한 잔재물은 양 및 질적인 측면에서 볼 때 추가 공정을 통하여 충분히 고형연료로 생산이 가능하다. Bio-drying 기술은 폐기물 내에 존재하는 생분해성 유기물질에 대한 미생물의 호기성 분해열을 이용하여 폐기물의 수분을 건조시키는 건조에너지 소모 및 설치/운영비를 최소화 할 수 있는 경제성이 우수한 기술이다. 본 연구에서는 고형연료화 시설에서 발생된 잔재물을 대상으로 Bio-drying 기술을 적용시켜 생산된 비성형 고형연료의 벤치규모 연소실험을 통해 연소 공기비에 따른 바닥재와 비산재의 발생 특성을 고찰하였다. 또한 기존 시중에 판매되고 있는 비성형 고형연료와의 연소특성 비교/분석을 통해서 Bio-dyring 고형연료의 연소특성을 파악하고 연소 조건의 최적화를 진행하였다. Bio-drying 고형연료와 판매용 고형연료의 연소 바닥재의 XRF 분석 결과 CaO, SiO2, Al2O3, Fe2O3가 주성분을 이루며 그 중에서 CaO 성분이 각각 36.6%와 48.6%로 가장 높게 나타났다.