One of the promising candidates for heat transfer fluid is molten chloride salts. They have been studied in various fields such as the electrolyte of pyroprocessing, the molten salt reactor coolant, and the energy storage system media. Main considerations for utilizing molten chloride salts are the compatibility of salts with structural materials. The corrosion behavior of structural materials in molten chloride salts must be understood to identify suitable materials against the corrosive environment. In this study, the corrosion behavior of a candidate structural material, Hastelloy N, in molten LiCl- KCl salt at 500°C were investigated by the electrochemical impedance spectroscopy (EIS) method. The sheet type of Hastelloy N was utilized as the working electrode in LiCl-KCl to measure the EIS data for 100 hours with 5 hours of time intervals. The EIS data were measured in the frequency range from 104 Hz to 10-2 Hz with the AC signal (amplitude = 20 mV) at open circuit potential. The capacitance semicircle observed in Nyquist plots for all periods indicates that charge-transfer controlled reactions occur. As the immersion time progresses, the radius of the semicircle in Nyquist plots and the impedance and phase angle in Bode plots decrease. These behaviors suggest a decreasing reaction resistance and the corrosion reactions are accelerated with the immersion time. The EIS data were fitted using the equivalent circuit to achieve quantitative results. Two capacitor-resistor components were considered due to the overlapped shape of two valleys in phase angle. The depressed shape of the semicircle in Nyquist plots led to the use of the constant phase element(Q) instead of the capacitor. Therefore, R(Q(R(QR))) circuit was selected to fit the EIS data. Fitting results show that the charge transfer resistance decreases dramatically within 1 day and then converges. The film resistance shows no clear trends, but the increase of the film admittance value indicates the decreased film thickness. Consequently, the film appears to exist like the oxide layer but it does not act as a protective layer. The real-time EIS data were measured in molten salt and provides the corrosion behavior over time. The corrosion mitigation strategy should consider that the corrosion of Hastelloy N accelerates over time and its intrinsic film cannot act as the protective layer. The next steps of this study are to evaluate other candidate structural materials and to demonstrate the presence of the film.

The recycling of solid waste materials to fabricate carbon-based electrode materials is of great interest for low-cost green supercapacitors. In this study, porous carbon foam (PCF) was prepared from waste floral foam (WFF) as an electrode material for supercapacitors. WFF was directly carbonized at various temperatures of 600, 800, and 1,000 oC under an inert atmosphere. The WFF-derived PCF (C-WFF) was found to have a specific surface area of 458.99 m2/g with multi-modal pore structures. The supercapacitive behavior of the prepared C-WFF was evaluated using a three-electrode system in a 6 M KOH aqueous electrolyte. As a result, the prepared C-WFF as an active material showed a high specific capacitance of 206 F/g at 1 A/g, a rate capability of 36.4 % at 20 A/g, a specific power density of 2,500 W/kg at an energy density of 2.68 Wh/kg, and a cycle stability of 99.96 % at 20 A/g after 10,000 cycles. These results indicate that the C-WFF prepared from WFF could be a promising candidate as an electrode material for high-performance green supercapacitors.

The central theme of this work is the synthesis of single-walled carbon nanotubes (SWCNTs) through the chemical vapor deposition method (CVD). Single-walled carbon nanotubes are synthesized using catalyst-chemical vapor deposition of acetylene at 750 °C temperature. X-ray diffraction study gives a characteristic peak (002) at 26.55° corresponding to the existence of carbon nanotube confirms that the particles are crystalline in nature and hexagonal phase. An SEM and HRTEM outcome gives surface morphology of SWCNTs. The elemental composition was confirmed by EDAX. The ideal concentration of single-walled carbon nanotubes was used to design a novel electrochemical sensor for determining paracetamol (PA) using cyclic voltammetry. Electrochemical determination of paracetamol is described using a single-walled carbon nanotube modified carbon paste electrode (SWCNT/MCPE). The SWCNT/MCPE was used in this study to detect paracetamol electrochemically at pH 7.2 in a 0.2 M PBS with a scan rate of 50 mV s− 1. A single-walled nanotube modified carbon paste electrode was used to develop a sensitive and selective electrochemical technique for the detection of PA. The SWCNT/MCPE showed excellent electrocatalytic activity towards the oxidation of paracetamol in phosphate buffer solution. Therefore, with increased oxidation currents, the voltammetric responses of paracetamol at the bare carbon paste electrode are organized within cyclic voltammetric peaks.

Pentachlorophenol (PCP), as one of the common pesticide and preservatives, is easily accumulated in living organisms. Considering the high toxicity of PCP, the development of an effective and sensitive inspection method to determine the residual trace amounts of PCP continues to be a significant challenge. Herein, a convenient and sensitive electrochemical sensor is constructed by modifying glassy carbon electrode with cerium dioxide ( CeO2) nanoparticles anchored graphene ( CeO2-GR) to detect trace PCP. Benefiting from the two-dimensional lamellar structural advantages, the extraordinary electron-transfer properties, as well as the intensive coupling effect between CeO2 nanoparticles and graphene, the afforded CeO2- GR electrode nanomaterial possesses excellent electrocatalytic activity for the oxidation of PCP. Under the optimum synthetic conditions, the PCP oxidation peak currents of developed CeO2– GR sample exhibit a wide linear range of 5–150 μM. Moreover, the corresponding detection limit of PCP on the CeO2– GR electrode is as low as 0.5 μM. Apart from providing a promising electrochemical sensor, this work, most importantly, promotes an efficient route for the construction of highly active sensing electrode materials.

Double-layer capacitors (DLCs) are developed with high surface electrodes to achieve a high capacitance value. In the present work, the initial bulk concentration of 1 mol/m3 and 3 mol /m3 are selected to show the consequential effects on the performance of a double-layer capacitor. A 1D model of COMSOL Multiphysics has been developed to analyze the electric field and potential in cell voltage, the electric displacement field and polarization induced by the field, and energy density in a double-layer structure. The electrostatics and the electric circuit modes in COMSOL are used to simulate the electrochemical processes in the double-layer structure. The analytical analysis of a double-layer capacitor with different initial bulk concentrations is investigated by using Poisson-Nernst-Plank equations. From the simulation results, the differential capacitance changes as a function of compact layer thickness and initial bulk concentration. The energy density varies with the differential capacitance and voltage window. The values of energy density are dominated by the interaction of ions in the solution and electrode surface.

This work reported the electrochemical and photoelectrochemical (PEC) properties of a new photoelectrode based on hematite Co-Fe2O3@NiO, a photoactive semiconductor, was prepared using a process involving a combination of the co-precipitation and microwave-assisted synthesis of Fe2O3, Co-Fe2O3 and Co-Fe2O3@NiO, respectively. The obtained products were characterized by X-Ray powder Diffraction (XRD), Scanning Electron Microscope (SEM), Energy Dispersive X-ray analysis (EDX), Ultraviolet–Visible (UV–vis) analysis, Fourier Transform Infrared spectroscopy (FT-IR). X-ray diffraction (XRD) pattern of the sample determined the crystal structure of α-Fe2O3 nanoparticles. The SEM image shows spherical nanoparticles. FTIR spectrospy spectrum confirmed the phase purity and chemical bond for the sample. Optical studies show a variation of band gap from 2.118 to 2.07 eV. The electrochemical and photoelectrochemical (PEC) performance of the films were examined by cyclic voltammetry, linear sweep voltammetry and chronoamperometry. The electrochemical oxidation of water achieved by Cobalt-doped Fe2O3@ GCE modified electrode exhibited the current density of 21 mA/g at 0.5 V vs. SCE for 5 at% of Co and reveals enhanced specific capacitance of 352.11 F/g. The catalytic performance of urea oxidation was measured by cyclic voltammetry on Co-Fe2O3@NiO nanoparticles modified glassy carbon electrode (GCE) in alkaline medium. The electrode Co-Fe2O3@NiO without annealing showed a peak current density of 1.59 mA/cm2 at 0.1 M urea in 1.0 M NaOH, which was 3.6 fold higher than that of Co-Fe2O3@NiO with annealing. In another part, this work reported the photoelectrochemical (PEC) properties of photoanode prepared by spin coating. The highest photocurrent 0.042 mA/cm2 at 0.5 V Vs SCE was obtained for 5% Co-Fe2O3@NiO while the photocatalytic oxidation of urea.

Hypercrosslinked polymers HCPs have been widely used as precursors to prepare porous carbon materials because of their highly ordered porous structure and large specific surface area. In this paper, we used a solvothermal method to prepare a hypercrosslinked polymer, and the HCPC-700-A was prepared using an activation method with the hypercrosslinked polymer as the precursor. The effects of different carbon–alkali ratios on the microstructure, composition and electrochemical properties of porous carbon HCP were studied. The results show that the surface of porous carbon HCPC-700-A presents a relatively regular geometric shape, and a large number of pore structures are mainly micro- and mesopores. The specific surface area is 2074.53 m2 g− 1, and the average pore size is between 1.29 and 1.93 nm. Porous carbon HCPC-700-1:2 has excellent electrochemical performance in 1 M H2SO4, and the specific capacitance is up to 464.4 F g− 1 at a current density of 1 A g− 1. The specific capacitance decay rate is 29.72% when the current density is increased from 1 A g− 1 to 8 A g− 1. After 5000 cycles, the capacitance retention rate is 91.16% at a current density of 2 A g− 1, showing excellent electrochemical performance, good cycle stability and perfect energy storage performance. This research provides new experimental ideas for HCPs in the electrochemical energy storage field.

In this study, N/S co-doped carbon felt (N/S-CF) was prepared and characterized as an electrode material for electric double-layer capacitors (EDLCs). A commercial carbon felt (CF) was immersed in an aqueous solution of thiourea and then thermally treated at 800 oC under an inert atmosphere. The prepared N/S-CF showed a large specific surface area with hierarchical pore structures. The electrochemical performance of the N/S-CF-based electrode was evaluated using both 3- electrode and 2-electrode systems. In the 3-electrode system, the N/S-CF-based electrode showed a good specific capacitance of 177 F/g at 1 A/g and a good rate capability of 41% at 20 A/g. In the 2-electrode system (symmetric capacitor), the freestanding N/S-CF-based electrode showed a specific capacitance of 275 mF/cm2 at 2 mA/cm2, a rate capability of 62.5 % at 100 mA/cm2, a specific power density of ~ 25,000 mW/cm2 at an energy density of 23.9 mWh/cm2, and a cycling stability of ~ 100 % at 100 mA/cm2 after 20,000 cycles. These results indicate the N/S co-doped carbon felts can be a promising candidate as a new electrode material in a symmetric capacitor.

The effect of hydrogen peroxide on the electrochemical behavior of iron was investigated in perchlorate solutions. Iron showed four distinct behaviors in the perchlorate solutions of pH 3.0. First, the active dissolution regions of Fe with two current waves were observed in the potential range of −0.7 to 0 V (vs. SCE). Second, the stable passivation was found in the potential range between 0 and 0.3 V (vs. SCE). Third, unstable passivation region was observed in the potential range of 0.3 to 1.2 V (vs. SCE). Finally, pitting corrosion was observed at a potential above 1.2 V (vs. SCE). The pH increase stabilized the passivation process of iron, whereas the increase in temperature had a negative influence by enhancing the passivation and pitting behaviors of iron. The presence of hydrogen peroxide at the concentrations below 1.45 mM had an adverse effect on the formation of the passive layer. However, at concentrations above 1.45 mM, hydrogen peroxide affected a beneficial influence on the formation of stable iron oxide layer in the active dissolution region. In addition, regardless of the hydrogen peroxide concentration, the presence of hydrogen peroxide mitigated the pitting corrosion of iron.

Liquid Bi pool is a candidate electrode for an electrometallurgical process in the molten LiCl-KCl eutectic to treat the spent nuclear fuels from nuclear power plants. The electrochemical behavior of Bi3+ ions and the electrode reaction on liquid Bi pool were investigated with the cyclic voltammetry in an environment with or without BiCl3 in the molten LiCl-KCl eutectic. Experimental results showed that two redox reactions of Bi3+ on inert W electrode and the shift of cathodic peak potentials of Li+ and Bi3+ on liquid Bi pool electrode in molten LiCl-KCl eutectic. It is confirmed that the redox reaction of lithium with respect to the liquid Bi pool electrode would occur in a wide range of potentials in molten LiCl-KCl eutectic. The obtained data will be used to design the electrometallurgical process for treating actinide and lanthanide from the spent nuclear fuels and to understand the electrochemical reactions of actinide and lanthanide at liquid Bi pool electrode in the molten LiCl-KCl eutectic.

높은 안전성과 견고한 기계적 특성을 가진 고체상 슈퍼커패시터는 차세대 에너지 저장 장치로서 세계적 관심을 끌고 있다. 슈퍼커패시터의 전극으로서 경제적인 탄소 기반 전극이 많이 사용되는데 수계 전해질을 도입하는 경우 소수성 표 면을 가진 탄소 기반 전극과의 계면 상호성이 좋지 않아 저항이 증가한다. 이와 관련하여 본 연구에서는 전극 표면에 산소 플라즈마 처리를 하여 친수화된 전극과 수계 전해질 사이의 향상된 계면 성질을 기반으로 더 높은 전기화학적 성능을 얻는 방법을 제시한다. 풍부해진 산소 작용기들로 인한 표면 친수화 효과는 접촉각 측정을 통해 확인하였으며, 전력과 지속시간을 조절함으로써 친수화 정도를 손쉽게 조절할 수 있음을 확인하였다. 수계 전해질로 PVA/H3PO4 고체상 고분자 전해질막을 사 용하였으며 프레싱하여 전극에 도입하였다. 15 W의 낮은 전력으로 5초간 산소 플라즈마 처리를 시행하는 것이 최적 조건이 었으며 슈퍼커패시터의 에너지 밀도가 약 8% 증가하였다.

This work describes the facile synthesis of silver nanoparticle-decorated zinc oxide nanocomposite through a simple glycol reduction method. The silver nanoparticle-decorated zinc oxide nanocomposite-based pencil graphite electrode has been validated as a perceptive electrochemical sensing podium towards nitrite. The morphology of the prepared nanocomposite has been characterized via specific spectroscopic and electrochemical techniques. The sensor exhibits a notable enhancement in the cyclic voltammetric response to nitrite oxidation at an ideal peak potential of 0.76 V in pH 6.0 acetate buffer. Under optimum conditions of nitrite directly expanded with their concentration in the range from 30 to 1400 μM with a detection limit of 14 μM.

The electrochemical type gas sensor has the advantage of being easy to use due its small size, and it is also relatively inexpensive. However, its output can easily vary depending on temperature and humidity conditions. Therefore, it is important to ascertain the exact output characteristics of a sensor according to the measuring environment in order to improve measurement accuracy for any set of given conditions. The purpose of this study is to obtain basic information about the output characteristics of a sensor that is used both indoor and outdoor according to the variation in temperature and humidity conditions in order to improve the accuracy of the sensor. To achieve this result, a calibration curve was made using ammonia standard gas and the calibration factor was calculated using the calibration curve and the measuring accuracy was confirmed with regard to the ammonia sensor. Based on the test results, the variation of the sensor output value was large in relation to temperature and humidity variation. It was found that the output value from the sensor at higher temperature and humidity conditions was also higher. However, the measuring accuracy of the sensor could be improved by more than 10% by applying the calibration factor and an average accuracy of more than 97% could be achieved. It is anticipated that the result of this study can be used as basic data to obtain more accurate results using electrochemical sensors for a given set of temperature and humidity conditions, and therefore, it can also be considered that the reliability and applicability of electrochemical sensors can be improved.

Ni-rich계 양극 소재는 낮은 가격과 높은 용량으로 인해 고용량 달성을 위한 상용화 소재로 주목받고 있지만, 이 소재의 경 우 전기화학적 불안정성으로 인한 한계를 가진다. 그래서 다양한 표면 코팅 방법을 통해 성능향상을 이루고 있지만, 성능향상이 소 재와 코팅 방법때문인지 또는 코팅 범위가 넓어진 것 때문인지는 모호하게 남아 있다. 본 연구에서는 전이금속으로 양극 활물질을 코팅할 때 전구체 코팅 범위에 따른 리튬이온배터리 전기화학 성능평가를 분석하였다. 상업용 LiNi0.8Co0.1Mn0.1O2 양극 소재 표면을 에탄올 용액에 용해된 리튬-코발트와 리튬-주석 아세테이트 전구체를 코팅하였고, 교반속도를 다르게 하여 (200 rpm 및 600 rpm) 전구체 코팅 범위를 다르게 하였다. 리튬-코발트 아세테이트 전구체의 경우 교반속도가 증가할수록 코팅 범위가 증가하였지만, 리튬 -주석 아세테이트 전구체의 경우 교반속도가 증가할수록 코팅 범위가 감소하였다. 하지만 원소의 종류에 관계없이 코팅 범위가 넓 은 경우에 상대적으로 우수한 전기화학적 성능을 나타내었다. 코팅된 양극 활물질의 물리적 특성은 SEM 및 XRD를 이용하여 분석하 였으며, 전기화학적 성능은 초기 충·방전 용량, 사이클 안정성 및 율속특성 테스트를 통해 조사하였다.

Tin/graphite composites are prepared as anode materials for Li-ion batteries using a dry ball-milling process. The main experimental variables in this work are the ball milling time (0–8 h) and composition ratio (tin:graphite=5:95, 15:85, and 30:70 w/w) of graphite and tin powder. For comparison, a tin/graphite composite is prepared using wet ball milling. The morphology and structure of the different tin/graphite composites are investigated using X-ray diffraction, Raman spectroscopy, energy-dispersive X-ray spectroscopy, and scanning and transmission electron microscopy. The electrochemical properties of the samples are also examined. The optimal dry ball milling time for the uniform mixing of graphite and tin is 6 h in a graphite-30wt.%Sn sample. The electrode prepared from the composite that is dry-ballmilled for 6 h exhibits the best cycle performance (discharge capacity after 50th cycle: 308 mAh/g and capacity retention: 46%). The discharge capacity after the 50th cycle is approximately 112 mAh/g, higher than that when the electrode is composed of only graphite (196 mAh/g after 50th cycle). This result indicates that it is possible to manufacture a tin/graphite composite anode material that can effectively buffer the volume change that occurs during cycling, even using a simple dry ball-milling process.

고용량 배터리에 대한 요구가 증가에 따라 기존 음극재보다 높은 용량(3,860 mAh/g)과 낮은 전기화학적 전위(– 3.040 V)를 갖는 리튬 금속 기반 음극재에 대한 연구가 활발하게 이루어지고 있다. 본 연구에서는 수열 합성을 통해 제작된 아나타제(anatase) 타입의 TiO2 나노 입자 기반한 PVdF-HFP/TiO2 복합체를 리튬 금속 음극의 계면 보호층으로 적용하였다. 결정구조 및 형상 분석을 통해 유/무기-리튬 나노복합체 박막의 형성을 확인하였다. 또한, 전지화학 테스트(사이클 테스트 및 전압 프로파일)를 통해 리튬 금속 음극의 전기화학 성능은 복합체 보호막이 TiO2 10 wt%, 코팅 두께 1.1 μm의 조건에서 가장 개선된 전기화학적 성능(콜롱 효율 유지: 77 사이클 동안 90% 이상) 발현을 확인하였다. 이를 통해, 처리하지 않은 리튬 전극 대비 본 보호층에 의한 리튬 금속 음극의 성능 안정화/개선 효과가 검증되었다.

As the size of market for electric vehicles and energy storage systems grows, the demand for lithium-ion batteries (LIBs) is increasing. Currently, commercial LIBs are fabricated with liquid electrolytes, which have some safety issues such as low chemical stability, which can cause ignition of fire. As a substitute for liquid electrolytes, solid electrolytes are now being extensively studied. However, solid electrolytes have disadvantages of low ionic conductivity and high resistance at interface between electrode and electrolyte. In this study, Li7La3Zr2O12 (LLZO), one of the best ion conducting materials among oxide based solid electrolytes, is fabricated through RF-sputtering and various electrochemical properties are analyzed. Moreover, the electrochemical properties of LLZO are found to significantly improve with co-sputtered Li2O. An all-solid thin film battery is fabricated by introducing a thin film solid electrolyte and an Li4Ti5O12 (LTO) cathode; resulting electrochemical properties are also analyzed. The LLZO/Li2O (60W) sample shows a very good performance in ionic conductivity of 7.3  108 S/cm, with improvement in c-rate and stable cycle performance.