PURPOSES : Concrete, which is a construction material, is the most widely used compression material; however, unlike steel, it exhibits nonlinear material characteristics. Therefore, to examine the behavior of structures under the nonlinear conditions of concrete materials, one must select an appropriate numerical-analysis technique and a reasonable material model. When performing the nonlinear numerical analysis of a structure using general-purpose structural analysis software, the stress–strain curve or the Mohr–Coulomb failure criterion is typically employed to consider the nonlinear material characteristics. In this study, an efficient nonlinear numerical analysis is conducted by defining the stress–strain curves and Mohr–Coulomb parameters applicable to Strand7 to examine and design the stability of reinforced concrete structures. METHODS : This study was conducted by improving existing data. Based on the tensile region of the concrete stress–strain curve presented in a simple shape and the results of the splitting test, the proposed Mohr–Coulomb parameter was improved based on regulations stipulated in the design standards of concrete structures. The characteristics and usability of the improved material models were examined using concrete splitting tensile and bending models. RESULTS : A yield area distribution similar to that of the reference data is obtained when the Mohr–Coulomb material model is used in the numerical analysis of the concrete splitting tension, thus confirming the validity of the model. In the Mohr–Coulomb material model, nonlinear resistance continues even after the maximum reaction force occurs. However, when the stress–strain curve material model is applied, at the moment the maximum reaction force occurs, the material yields and begins to be damaged. In addition, by applying the Mohr–Coulomb material model to the bending numerical-analysis model, the magnitude of stress in the tensile region from the initial stage exceeds the yield stress defined in the stress–strain curve. CONCLUSIONS : Based on a series of examples, the usability of the proposed concrete stress–strain curve and Mohr–Coulomb parameters is confirmed. However, to obtain numerical-analysis results that are consistent with the nonlinear behavior of actual structures, nonlinear testing of reinforced concrete structures shall be conducted and material models shall be improved.

Radiant tubes heat exchangers are critical components that facilitate the heat transfer process to steel in an annealing furnace, and it addresses several engineering problems, such as thermal stress and mechanical failure due to long-term thermal cycling, which can significantly affect the longevity of the tubes and maintenance requirements. In this study, we used commercial software (ANSYS) to simulate the thermal stress and deformation of radiant tubes subjected to extreme thermal conditions and pressure loads. We evaluated both thermally induced deformation and creep deformation, which is a time-dependent deformation under constant stress over the long term. The results showed that uneven temperature conditions and pressure loads lead to significant deformation and potential failures. To mitigate these engineering challenges, we also tested several designs that include supporting brackets. This study provides valuable insights for designing radiant tube heat exchangers in annealing furnaces to extend their lifespan and ensure system safety.

In order to investigate the optimum condition of the autofrettage process for the diesel engine fuel injection pipe, different values of autofrettage pressure, pressure rising time, pressure holding time, and repetition of autofrettage process were applied. Autofrettage was performed by applying the hydrostatic internal pressures of 604MPa, 535MPa, 500MPa on the fuel injection pipe, corresponding to theoretical 50%, 30%, and 20% overstrain levels, respectively. The autofrettage residual stresses in the injection pipe were experimentally determined by using X-ray diffractometer. As the overstrain level increased, the magnitude of compressive residual stress at the bore increased. It was found that the rising time to reach the autofrettage pressure, holding time at the autofrettage pressure, and repeated application of the autofrettage pressure on the pipe had no significant influence on the residual stress distributions.

This paper reports the results of an experimental examination using X-rays to test annealing materials for lapped bearing steel (STB2), to confirm the validity of the weighted averaging analysis method. The distribution behavior for the sin diagram and the presence or absence of differences in the peak method, half-value breadth method, and centroid method were investigated. When lapping the annealed bearing steel (STB2) material, a residual stress state with a non-directional steep gradient appeared in the surface layer, and it was found that the weighted averaging analysis method was effective. If there is a steep stress gradient, the sin diagram is curved and the diffraction intensity distribution curve becomes asymmetric, resulting in a difference between the peak method, half-value breadth method, and centroid method. This phenomenon was evident when the stress gradient was more than 2~3 kg/mm2/μm. In this case, if the position of the diffraction line is determined using the centroid method and the weighted averaging analysis method is applied, the stress value on the surface and the stress gradient under the surface can be obtained more accurately. When the stress gradient becomes a problem, since the curvature of the sin diagram appears clearly in the region of sin > 0.5, it is necessary to increase the inclination angle  as much as possible. In the case of a lapping layer, a more accurate value can be obtained by considering  in the weighted averaging analysis method. In an isotropic biaxial residual stress state, the presence or absence of  can be determined as the presence or absence of strain for sin≈0.4.

The most comprehensive and particularly reliable method for non-destructively measuring the residual stress of the surface layer of metals is the sin method. When X-rays were used the relationship of sin measured on the surface layer of the processing metal did not show linearity when the sin method was used. In this case, since the effective penetration depth changes according to the changing direction of the incident X-ray,  becomes a sin function. Since  cannot be used as a constant, the relationship in sin cannot be linear. Therefore, in this paper, the orthogonal function method according to Warren’s diffraction theory and the basic profile of normal distribution were synthesized, and the X-ray diffraction profile was calculated and reviewed when there was a linear strain (stress) gradient on the surface. When there is a strain gradient, the X-ray diffraction profile becomes asymmetric, and as a result, the peak position, the position of half-maximum, and the centroid position show different values. The difference between the peak position and the centroid position appeared more clearly as the strain (stress) gradient became larger, and the basic profile width was smaller. The weighted average strain enables stress analysis when there is a strain (stress) gradient, based on the strain value corresponding to the centroid position of the diffracted X-rays. At the 1/5 max height of X-ray diffraction, the position where the diffracted X-ray is divided into two by drawing a straight line parallel to the background, corresponds approximately to the centroid position.

본 논문에서는 역전파 방법 기반 자동미분법을 이용하여 설계민감도를 구하고 이를 응력제한조건을 고려한 위상최적설계에 적용 하였다. 응력제한조건이 있는 위상최적화문제는 특이점(singularity)과 응력의 국부성(local nature of stress constraint)문제, 그리고 설 계 변수에 대한 비선형성의 문제를 포함하고 최적해를 얻기가 매우 힘들다. 특이점 문제를 해결하기 위해서 응력 완화(stress relaxation) 기법을 사용하였고, 응력의 국부성을 해결하기 위해 p-norm을 이용한 전역 응력치를 제한조건에 사용하였다. 설계 변수에 대한 비선 형성을 극복하기 위해 해석적인 방법으로 정확한 설계민감도를 구하는 것이 중요하다. 위상최적설계에서 기존에는 보조변수방법 (adjoint variable method)을 사용하여 빠르고 정확한 설계민감도를 구했지만, 설계민감도를 해석적으로 구해야 하고, 보조평형방정식 을 추가로 풀어야 하는 어려움이 있다. 이를 해결하기 위해서 인공신경망에서 최적 가중치(weights)와 편차(biases)를 구할 때 쓰이는 역전파 기법을 이용하여 설계민감도를 구하고 이를 응력제한조건을 고려한 위상최적설계에 적용하였다. 역전파 기법은 자동미분에 쓰이는 기법으로 목적함수나 제한조건에 대한 설계민감도를 별도의 수식유도 없이 간단하게 구할 수 있는 장점이 있다. 또한, 미분값 을 구하는 역전파의 과정이 보조평형방정식을 푸는 것보다 계산시간이 빠르고 해석적 방법으로 구한 설계민감도와 같은 정확도를 보 여준다

세장 구조물은 동하중에 매우 취약한 구조시스템으로써 와흘림에 의한 와류유발진동(Vortex-Induced Vibration, VIV)이 발생 할 가능성이 크다. 또한 와류유발진동이 구조물의 고유진동수 영역에서 발생하는 경우 공진이 지속되는 Lock-in 현상으로 피로 파괴 의 우려가 있다. 본 논문에서는 공진주파수가 유동 조건의 변화에도 불구하고 유지되는 현상의 원인을 분석하기 위해서 유체로 인한 구조물의 동적 거동에 대하여 해석을 수행하였다. 유동의 방향과 수직 방향으로 자유 거동하는 1 자유도의 구조시스템의 2차원 원형 실린더 단면을 대상으로 비정상 층류영역을 가정하였다. 물체의 움직임을 고려하여 매시간 유동장의 격자를 재생성하는 Remeshing 기 법을 사용하였고 물체의 운동방정식과 유동의 지배방정식을 순차적으로 수치계산하는 유체-구조 연성 해석을 수행하였다. 본 연구에 서 구현한 Lock-in 현상은 선행연구와 잘 일치하였고, Lock-in 현상에서 운동진폭이 증가하는 특성이 잘 모사되었다. 또한 단면에서 전 단응력의 변화로 인한 박리현상과 공진주파수가 지속되는 현상의 관계를 분석하였다.

In this analysis, the analytical model was verified through the normal mode analysis of the piston for the 2.9 liter IDI (indirect injection) engine. Heat transfer analysis was carried out by selecting two cases of applied temperature using the validated model. The first case was a condition of 350℃ on the piston upper surface and 100℃ on the piston body and inner wall. In the second case, the conditions were set to give a temperature of 400℃ on the upper surface of the piston and 100℃ on the piston body and the inner wall. In addition, the temperature distribution due to heat transfer was obtained for the pistons with boundary conditions of two cases, and then the thermal stress distribution due to thermal expansion was obtained using the input. Using this analysis result, the thermal stress caused by thermal expansion due to the thermal conduction of the piston is examined and used as the basic data for design.

본 논문에서는 상용프로그램을 이용한 유한요소해석을 통하여 포스트텐션 정착구역에서 보다 효율적인 응력분산이 가능 한 비부착식 단일 강연선용 포스트텐션 정착구 형상을 개발하는 것을 목표로 하였다. 이를 위하여 정착구 형상을 구성하는 각 부분의 변수해석을 수행하였다. 본 연구에서 제안한 정착구 형상을 사용하였을 때 발생하는 최대파열응력이 기존의 정착 구를 사용한 경우와 비교하여 정착구역내의 최대파열응력이 감소함을 확인하였다. 또한 본 연구의 정착구 형상을 사용하는 경우 최대파열응력 산정을 위해 AASHTO 및 기존 연구자들의 파열력 산정식을 통해 산출된 파열력을 비교 및 분석하였다. 그 결과 정착구 형상에 따른 위치계수를 수정한 파열력 산정식을 적용할 경우 정착구역이 효율적인 보강설계가 가능할 것으 로 판단되었다.

고준위폐기물 처분용기를 처분장에서 처분 시 사고로 운송차량에서 추락낙하 하여 지면과 충돌하는 경우 처분용기에 가 해지는 충격력에 의해 처분용기에 응력이 발생한다. 본 논문에서는 고준위폐기물 처분용기의 구조안전성 설계과정의 일환으 로 이와 같은 충격력에 의하여 여러 가지 처분용기 모델에 발생하는 응력에 대한 비교연구를 수행하였다. 연구의 주된 내용 은 이와 같은 비교연구를 통하여 구조적으로 건전한 처분용기의 설계에 관한 것이다. 처분장에서 운반차량으로 처분용기 운 반 중 사고로 추락낙하 하여 지면과의 충돌 시에 처분용기에 가해지는 충격력은 기구동역학해석 상용 컴퓨터코드인 RecurDyn으로 구하였다. 이렇게 구한 충격력에 의하여 여러 가지 처분용기 모델에 발생하는 응력 및 변형은 유한요소해석 상용 컴퓨터코드인 NISA를 이용하여 구하였다. 이 응력과 변형 값들의 비교 검토를 통하여 구조적으로 건전한 처분용기에 대한 연구를 수행하였다. 연구결과 처분용기 내부 고준위폐기물 다발을 감싸는 외곽 벽의 두께가 두꺼워 질수록 또는 처분 용기의 직경이 커질수록 처분용기에 발생하는 응력이 커지는 것을 알 수 있었다. 그러나 처분용기에 가해지는 충격력도 처 분용기의 직경이 커짐에 따라 증가하였다. 그럼에도 불구하고, 단위 충격력 당 발생하는 변형의 크기는 직경이 증가함에 따 라 감소하였다. 따라서 결론적으로 직경이 증가할수록 처분용기는 구조적으로 건전함을 알 수 있었다.

섬유강화 복합재료는 열팽창 계수의 방향성을 갖고 있을 뿐만 아니라 제작과정 온도와 실제 사용온도 사이의 차이 때문에 필연적으로 열응력 효과를 받게 된다. 이러한 열응력에 의한 파손현상은 실제 항공우주산업에서의 응용이 증대되고 있는 두 꺼운 복합 적층판의 경우에 더욱 현저한 현상으로 적층판의 역학적 기능 및 파단강도에 큰 영향을 미치게 된다. 본 연구에서 는 복잡한 재질로 구성되고 높은 세장비를 가진 블레이드 날개 구조의 차원축소 및 열 응력 복원 이론을 소개하고 3차원 유 한요소모델과 비교결과를 통해 효율성과 정확성을 입증한다. 또한 차원을 축소한 모델링을 구성하고 복원이론를 이용하여 열적 환경에 적용된 복합재 보 단면의 열응력을 차원 복원하고 시각적으로 형상화하는 효율적인 복원해석 과정을 소개하고 자 한다.

This study performs finite Element stress analysis of flange connections at noise barriers with circular steel tubes, which have a light weight. Subsequent numerical simulation results for three types of models (standard, double, and standard models strengthen by ribs) present that the applied connections for target noise barriers constructed show suitable structural performance. In this paper, the existing finite element stress analysis using the ABAQUS program is further extended to study the local stress distribution of the noise barriers with new type circular steel tubes. The numerical results for various parameters are verified by comparing different types with stresses occurred in the noise barrier from the numerical simulation.

High voltage electric power transmitter GIS(Gas Insulated Switchgear) above 72.5kV needs to satisfy domestic Korean peninsular standard(ES-6110-0002) in KEPCO with respect to normal and special operation conditions which include internal gas pressure, dead weight, wind and seismic load. Some other requirements not described in Korean standard can be applied from other international standards such as IEC(International Electronical Committee) 62271-203 and 62271-207. The GIS is a kind of pressure vessel structure made of aluminum and filled with SF6 gas of internal pressure 0.4～0.5MPa. Finite element analysis of GIS is performed with such operational loads including seismic loading and the stability and reliability is determined according to ASME BPVC(Boiler and Pressure Vessel Code) SEC. VIII standard where the allowable stress level of the pressure vessel is suggested. The result shows that the stress of GIS is satisfied the allowable stress level and the safety factor is about 2.3 for Korean peninsular standard.

As the size of the wind power becomes larger, the development of the assembly type wind power which is advantageous in transportation and installation is active. This advantage comes from the economic point of view, and the stiffener is applied to the inner side, so that the safety is high. Large wind power require door openings for maintenance. The door opening has an irregular cross-section, and an excessive stress active due to the door opening. In this paper, the stresses occurring around the door opening was analyzed. As a result, small stress values were appeared in the tower, as the number of stiffeners were increased. Also, stress values were decreased a little in the tower as the opening shape become to ellipse was closer.

PURPOSES: This study is primarily focused on evaluating the effects of the non-linear stress-strain behavior of RAP concrete on structural response characteristics as is applicable to concrete pavement. METHODS : A 3D FE model was developed by incorporating the actual stress-strain behavior of RAP concrete obtained via flexural strength testing as a material property model to evaluate the effects of the non-linear stress-strain behavior to failure on the maximum stresses in the concrete slab and potential performance prediction results. In addition, a typical linear elastic model was employed to analyze the structural responses for comparison purposes. The analytical results from the FE model incorporating the actual stress-strain behavior of RAP concrete were compared to the corresponding results from the linear elastic FE model. RESULTS : The results indicate that the linear elastic model tends to yield higher predicted maximum stresses in the concrete as compared to those obtained via the actual stress-strain model. Consequently, these higher predicted stresses lead to a difference in potential performance of the concrete pavement containing RAP. CONCLUSIONS : Analysis of the concrete pavement containing RAP demonstrated that an appropriate analytical model using the actual stress-strain characteristics should be employed to calculate the structural responses of RAP concrete pavement instead of simply assuming the concrete to be a linear elastic material.