The aim of this study is to evaluate the possibility of damage to cultural assets resulting from vibrations generated by construction vehicle traffic. The cultural heritage's natural vibration frequency was determined to be 150Hz by measurement. The damping ratios were calculated as 4.7% using the logarithmic decrement approach and 4.3% using the half-power method. The vibration measurements obtained during vehicle operation indicated that, despite an increase in vehicle velocity of up to 15 km/h, the vibrations remained below the detectable level of 0.13 mm/sec. When the road is curved and the terrain is sloped, a suitable speed for vehicle operation was found to be around 17 km/h, at which point vibrations were seen. The highest recorded vibration amplitude at this velocity was 0.217 mm/sec, which remains below the stringent regulation limit of 2 mm/sec. Thus, it can be concluded that there is no actual harm caused by vibrations.

The recent increase in earthquake activities has highlighted the importance of seismic performance evaluation for civil infrastructures. In particular, the container crane essential to maintaining the national logistics system with port operation requires an exact evaluation of its seismic response. Thus, this study aims to assess the seismic vulnerability of container cranes considering their seismic characteristics. The seismic response of the container crane should account for the structural members’ yielding and buckling, as well as the crane wheel’s uplifting derailment in operation. The crane’s yielding and buckling limit states were defined using the stress of crane members based on the load and displacement curve obtained from nonlinear static analysis. The derailment limit state was based on the height of the rail, and nonlinear dynamic analysis was performed to obtain the seismic fragility curves considering defined limit states and seismic characteristics. The yield and derailment probabilities of the crane in the near-fault ground motion were approximately 1.5 to 4.7 and 2.8 to 6.8 times higher, respectively, than those in the far-fault ground motion.

최근 회전 회전기계의 건전성 관련 연구가 활발하게 진행중이며, 조선업의 대표적인 회전기계인 갠트리 크레인에도 이를 적용하고자 하는 연구가 활발하게 진행되고 있다. 하지만 조선업의 갠트리 크레인의 경우 상대적으로 낮은 RPM으로 구동되고 잦은 운 전과 정지가 이루어지며 충격, 소음 등의 외부환경 인자가 측정 데이터에 영향을 크게 미쳐 오차를 발생시킬 수 있다. 본 연구에서는 조선업의 내업공정에서 사용되는 갠트리 크레인의 Hoist 모사장비를 제작하여, 운전조건(RPM) 변화와 데이터 획득 센서의 위치 차이가 획득 데이터에 미치는 오차를 통계적으로 분석하였다. 연구결과 상대적으로 낮은 운전조건에서는 센서 위치 차이에 따른 획득 데이터 의 오차는 크게 발생하지 않았으나, 상대적으로 높은 운전조건에서는 획득 데이터의 오차가 크게 발생하는 것으로 확인하였으며, 회전 기계의 데이터 획득 시 운전조건과 획득 센서위치가 획득 데이터에 영향을 미치는 것으로 확인하였다.

Since cranes are a kind of complex human-machine systems, it is almost impossible to completely secure safety with current technologies. Therefore, managerial interventions to prevent human errors are needed for safely operating a crane. The Occupational Safety and Health law states that cabin-type crane operators should have crane drivers’ licence and crane-related operators (e.g., pendent-type crane operators, slinging workers) should take a special safety training. However, statistics on industrial accidents showed that fatalities due to crane accidents (185 accidents occurred during 2013~2017) were the highest among hazardous machinery and equipment. To effectively control the crane-related accidents, voices of crane workers need to be analyzed to investigate the current status. This study surveyed perceived causes of crane accidents and status of special safety training for crane workers of 387. The survey revealed that 24.3% of the respondents experienced crane accidents and 31.4% eye-witnessed crane accidents. 79% of the respondents pointed human errors such as improper crane operation and improper slinging as the first cause. Lastly, only 16.7% of the respondents took a professional special safety training; but the rest took lecture-based or incomplete education. The findings of the present study can be applied to improve crane-related policies and special safety training systems.

Crane is an important equipment for the transport of heavy goods in industrial sites, but it is also known as one of the most fatal machines. In order to reduce crane accidents, it is necessary to minimize human errors during crane operations. To achieve this, ergonomic design principles are recommended to be reflected from the crane design stage. The study analyzed the safety certification standards for crane that should be fulfilled at the crane design and manufacturing stage. This study selected five representative ergonomic design principles (feedback, compatibility, consistency, full-proof, and fail-safe) by surveying heuristic evaluation principles that are widely used for usability evaluation in early design stage. Next, the principles were applied to the safety certification standards to identify insufficient clauses. This study identified 12 insufficient clauses out of 119 in the current safety certification standards for crane and discussed their improvement directions to comply the ergonomic principles. The analysis results of this study can help of improving the safety certification standards and the method used in this study can also be applied to identify insufficient clauses in the safety certification standards for other industrial machines such as press machine and lift.

In this study, system modeling and dynamic analysis of crane are conducted. Especially, among many different kinds of a crane system, the issues on crane operating problems installed on the vessel are considered. As well known, marine systems including cranes are exposed to various disturbances such as vessel motions, hydrodynamic forces, wave and wind attack, etc. In order to analysis the system dynamic with environmental conditions, the authors derived the nonlinear dynamic model of offshore crane and derived a linear model which is used for designing the control system. Using the obtained nonlinear and linear models, simulations were conducted to evaluate the usefulness of the obtained models. By simulation and result evaluation, the usefulness of the linear model, which presents the dynamics, is effectively verified.

2016년 3월 6.67톤 어선이 크레인 작업을 하던 중 복원성 상실로 인한 전복 사고가 발생하였다. 전복은 충돌, 접촉, 좌초, 화재 및 폭발의 결과로 발생한 사고는 제외하고 선박이 뒤집힌 것을 말한다. 지난 9년동안(2010-2018), 전복 사고는 전체 해양사고의 2.34%를 차 지하고 있으며 증가와 감소를 반복하고 있다. 10톤 미만 소형어선의 주된 전복사고 원인은 부적절한 선적에 따른 복원성 상실이다. 어선 법에 따르면 소형 어선은 복원성과 1톤 미만 제한 하중 크레인에 대해서 복원성과 예비검사를 면제해 주고 있다. 본 연구는 고성에서 발 생한 소형 어선의 전복 사고 재결서의 원인으로 언급된 사항 중 크레인 증량에 따른 복원 모멘트 감소에 대해 실제 제원이 비슷한 어선 을 모델링하여 이를 통해 사고 전·후의 어선 상태를 가상하여 복원성을 비교하였다. 그 결과 기존 보다 무거운 크레인으로의 교체 시에는 복원 모멘트 감소와 현단몰입각의 감소로 전복의 위험성이 증가되었다. 표준재화 상태에서는 입·출항시 보다는 어로 활동을 하고 있는 상황에서의 복원 모멘트가 감소되는 것을 확인하였다.

This paper considers the problem of scheduling loading and unloading operations of a crane in a railway terminal motivated from rail-road container transshipment operations at Uiwang Inland Container Depot (ICD). Unlike previous studies only considering the total handling time of containers, this paper considers a bi-criteria objective of minimizing the weighted sum of the total handling time and tenant service time. The tenant service time is an important criterion in terms of terminal tenants who are private logistics companies in charge of moving containers from/to the terminal using their trucks. In the rail-road container shipment yard, the tenant service time of a tenant can be defined by a time difference between beginning and finishing loading and unloading operations of a crane. Thus, finding a set of sequences and time of the crane operations becomes a crucial decision issue in the problem. The problem is formulated as a nonlinear program which is improved by linearizing a nonlinear constraint in the model. This paper develops a genetic algorithm to solve the problem and performs a case study on the Uiwang ICD terminal. Computational experiment results show that the genetic algorithm shows better performance than commercial optimization solvers. Operational implications in terms of tenants are drawn through sensitivity analyses.

Construction sites have gradually become bigger and bigger according to Korea economic growth. Also use of tower crane and other heavy equipment has been increased. The increased use of heavy equipment like tower crane is leading to fatality incident. This study will verify hazards to influence tower crane incident through structural and positive verification and find which hazard influence incident risk. The result of this study is as follows. First, while there is a significant difference between safety managers and tower crane operators for working environment, safety management, personal manage among risk factors, we can not find any evidence on the difference in perception of tower crane incident risk between them. Second, task manage risk and personal manage risk has a significant positive effect on perception of tower crane incident risk. Third, while site environment risk has a significant positive moderating effect of task type between risk factors and perception of tower crane incident risk, personal environment risk has a significant negative moderating effect between them.