This study was carried out to investigate the proper wattage and installation distance for the efficient use of nano-carbon fiber infrared heating lamp (NCFIHL), a heating device advantageous for heating energy saving, when the production of watermelon plug seedlings in the plug seedling nursery in winter season. Six small beds were divided into plastic film, and 700 W and 900 W nano-carbon fiber infrared heating lamps were installed at 100 cm above the bed. 1 lamp at central (control), 60 cm interval (2 lamps), and 40 cm interval (3 lamps) heating lamps were installed in each bed inside the greenhouse. All treatments, except the control, were set to keep the night air temperature at 20℃ after lighting the NCFIHL. The leaf temperature showed a tendency to increase fast as the install distance was narrow. The leaf length and leaf width tended to increase as the installation distance of the 700 W heating lamp was narrow. The compactness was high in 700 W heating lamp with 40 cm of installation distance. Therefore, in consideration of maintaining the set temperature at night, installing 700 W electric lamps at 40 cm was an efficient power and installation distance for watermelon grafted seedlings considering economic feasibility.

This paper studies the flow characteristics inside the low-temperature carbonization(LTF) including sealing chamber with labyrinth. The flow behavior inside the furnace was analyzed according to different labyrinth shapes. The effects of labyrinth baffle number, and clearance between upper and lower baffles in the sealing chamber were investigated. The large vortex and stagnation region are generated in the chamber when the gap between the baffle and baffle is small. As a result, the gas discharge flow rate can be increased by 29.4% when the flow space of labyrinth is made 75% of the baffle length.

Energy storage systems should address issues such as power fluctuations and rapid charge-discharge; to meet this requirement, CoFe2O4 (CFO) spinel nanoparticles with a suitable electrical conductivity and various redox states are synthesized and used as electrode materials for supercapacitors. In particular, CFO electrodes combined with carbon nanofibers (CNFs) can provide long-term cycling stability by fabricating binder-free three-dimensional electrodes. In this study, CFO-decorated CNFs are prepared by electrospinning and a low-cost hydrothermal method. The effects of heat treatment, such as the activation of CNFs (ACNFs) and calcination of CFO-decorated CNFs (C-CFO/ACNFs), are investigated. The C-CFO/ACNF electrode exhibits a high specific capacitance of 142.9 F/g at a scan rate of 5 mV/s and superior rate capability of 77.6% capacitance retention at a high scan rate of 500 mV/s. This electrode also achieves the lowest charge transfer resistance of 0.0063 Ω and excellent cycling stability (93.5% retention after 5,000 cycles) because of the improved ion conductivity by pathway formation and structural stability. The results of our work are expected to open a new route for manufacturing hybrid capacitor electrodes containing the C-CFO/ACNF electrode that can be easily prepared with a low-cost and simple process with enhanced electrochemical performance.

Cu matrix composites reinforced with chopped carbon fiber (CF), which is cost effective and can be well dispersed, are fabricated using electroless plating and hot pressing, and the effects of content and alignment of CF on the thermal properties of CF/Cu composites are studied. Thermal conductivity of CF/Cu composite increases with CF content in the in-plane direction, but it decreases above 10% CF; this is due to reduction of thermal diffusivity related with phonon scattering by agglomeration of CF. The coefficient of thermal expansion decreases in the in-plane direction and increases in the through-plane direction as the CF content increases. This is because the coefficient of thermal expansion of the long axis of CF is smaller than that of the Cu matrix, and the coefficient of thermal expansion of its short axis is larger than that of the Cu matrix. The thermal conductivity is greatly influenced by the agglomeration of CF in the CF/Cu composite, whereas the coefficient of thermal expansion is more influenced by the alignment of CF than the aggregation of CF.

이 연구는 탄소섬유시트의 보강겹수와 보강위치에 따른 I형 PFRP 휨부재의 휨보강 효과에 대해 조사하였다. 또한, 탄소섬유시트로 보강한 PFRP 휨부재의 실험적, 이론적으로 확인하기 위해 유한요소해석을 실시하였으며, 휨실험 결과와 이론적 해석결과를 비교분석하였다. 휨실험 결과와 유한요소해석 결과는 이론적인 결과와 비교한 결과 일치하는 경향을 보였고, 휨보강 효과가 큰 탄소섬유시트 2겹을 보강한 시편에서 결과에서 오차가 가장 크게 발생하였다.

취성특성을 가진 탄소섬유복합체의 인장특성을 결정하기 위해 ASTM D 3 0 39에 따라 인장시험을 실시하였다. 극한시 점에 박리, 부분파단으로 인해 스트레인 게이지의 계측값의 변동성이 커져 신뢰성을 확보하기 어렵기 때문에 극한응력과 탄성 계수를 이용한 유효극한변형률을 제안하고, 극한계측변형률과 상호보완하였다. 특히 게이지가 비정상적으로 작용할 경우에도 적용이 가능하다는 장점이 있다. 또한 유효극한변형률을 결정하는 탄성계수는 단일시편에서 여러 변형률 구간에 대하여 평가하여 비교 검증할 수 있다.

Tungsten disulfide (WS2), a typical 2D layerd structure, has received much attention as a pseudocapacitive material because of its high theoretical specific capacity and excellent ion diffusion kinetics. However, WS2 has critical limits such as poor long-term cycling stability owing to its large volume expansion during cycling and low electrical conductivity. Therefore, to increase the high-rate performance and cycling stability for pseudocapacitors, well-dispersed WS2 nanoparticles embedded in carbon nanofibers (WS2-CNFs), including mesopores and S-doping, are prepared by hydrothermal synthesis and sulfurizaiton. These unique nanocomposite electrodes exhibit a high specific capacity (159.6 F g−1 at 10 mV s−1), excellent high-rate performance (81.3 F g−1 at 300 mV s−1), and long-term cycling stability (55.9% after 1,000 cycles at 100 mV s−1). The increased specific capacity is attributed to well-dispersed WS2 nanoparticles embedded in CNFs that the enlarge active area; the increased high-rate performance is contributed by reduced ion diffusion pathway due to mesoporous CNFs and improved electrical conductivity due to S-doped CNFs; the long-term cycling stability is attributed to the CNFs matrix including WS2 nanoparticles, which effectively prevent large volume expansion.

In this study, gas flow pattern and temperature distribution in a laboratory scale low temperature furnace for carbonization were numerically analyzed. The furnace was designed for testing carbonization process of carbon fibers made from polyimide(PI) precursor. Nitrogen gas was used as a working gas and it was treated as an ideal gas. Three-dimensional computational fluid dynamics analysis for steady state turbulent flow was used to analyze flow pattern and temperature field in the furnace. The results showed that more uniform velocity profile and axisymmetric temperature distribution could be obtained by varying mass flow rate at the inlets.

이 연구는 탄소섬유시트의 보강겹수에 따른 I형 PFRP 휨부재의 휨보강 효과를 조사하기 위해 길이 600mm의 PFRP 휨부재와 상하부 플랜지에 1mm 두께의 탄소섬유시트로 보강하여 휨실험을 수행하였다. 또한, 탄소섬유시트의 보강겹수와 보강 위치에 따른 I형 PFRP 휨부재의 휨보강 효과와 단면 감소량에 대해 조사하였다. 그 결과 2겹으로 보강하였을 때 휨강도와 휨강성이 증가함을 확인하였다.

In this study, carbon fiber Z-pins were fabricated by applying the different manufacturing process, and pull out test was performed for the dumbbell type of test specimens. Carbon fiber Z pins with smooth surface(type I) and stepped surface(type II, type III) were fabricated by using autoclave. Carbon fiber Z-pins with stepped surface were manufacturing method, that is, mold forming and machining process. The experimantal results show that carbon fiber Z pins have superior pull-out characteristics to carbon steel Z-pins. Pull-out load and pull-out toughness of carbon fiber Z pins with stepped surface are larger than those of carbon fiber Z-pins with smooth surface. Pull-out load and pull out toughness of mold f ormed Z-pin are 31% and 218% larger than those of smooth surfaced Z-pins, respectively.

Commercial carbon fiber is sized with Bisphenol A type epoxy, a thermosetting resin, to prevent fiber damage due to friction during weaving and manufacturing processes. When the thermoplastic resin is used as the base material, the interface between the carbon fiber and the thermoplastic resin is very weak because the bonding force with the thermosetting resin is not good, which greatly affects the mechanical properties of the composite material. Therefore, in order to improve the mechanical properties of the thermoplastic composite material, a process of removing the epoxy sizing layer on the surface of the carbon fiber in a furnace is required. In this process, the physical properties of the carbon fiber are changed according to the change of carbon fiber heat treatment conditions. In this paper, the study was carried out to evaluate the tensile strength required for automobile parts by extrusion and injection of thermoplastic resin based carbon fiber composites. Depending on the heat treatment temperature and time of the carbon fiber was a slightly tensile strength of the carbon composite material occurs, the tensile strength of the carbon composite material with a 6 hour heat-treated carbon fiber was measured at 550 ℃ the highest to 93 MPa. When the heat treatment holding time is more than 6 hours or the heat treatment temperature is more than 600 ℃, it may be the damage to the carbon fiber, which can cause a decrease in the tensile strength of the carbon fiber composite material.

As carbon fibers have the high performance, such as high strength, light weight, and high corrosion resistance, they are gradually expanding and growing at various industries. In particular, this study was conducted to determine whether the market could be applied to street lanterns among the construction sectors expected to grow in scale. In this study, the material characteristics of street lanterns using carbon fiber composites were studied in order to determine whether carbon fiber composites could be applied as a substitute for stainless steel and cast iron street lanterns. The physical relationship was experimentally evaluated to obtain a suitable material through the comparison of physical properties of fiber composite materials.

To improve the performance of carbon nanofibers as electrode material in electrical double-layer capacitors (EDLCs), we prepare three types of samples with different pore control by electrospinning. The speciments display different surface structures, melting behavior, and electrochemical performance according to the process. Carbon nanofibers with two complex treatment processes show improved performance over the other samples. The mesoporous carbon nanofibers (sample C), which have the optimal conditions, have a high sepecific surface area of 696 m2 g−1, a high average pore diameter of 6.28 nm, and a high mesopore volume ratio of 87.1%. In addition, the electrochemical properties have a high specific capacitance of 110.1 F g−1 at a current density of 0.1 A g−1 and an excellent cycling stability of 84.8% after 3,000 cycles at a current density of 0.1 A g−1. Thus, we explain the improved electrochemical performance by the higher reaction area due to an increased surface area and a faster diffusion path due to the increased volume fraction of the mesopores. Consequently, the mesoporous carbon nanofibers are demonstrated to be a very promising material for use as electrode materials of high-performance EDLCs.