Among the test categories of the personal dosimetry performance test in Korea, the reference neutron radiation field used for the mixed neutron-photon radiation field is generated by a D2Omoderated 252Cf source. There are some differences depending on the standards, D2O-moderated 252Cf source consists of the 252Cf source surrounded by the D2O sphere with a diameter of 30 cm, covered with a Cd shell of thickness approximately 0.051 cm ~ 0.1 cm. In order to optimize the design of the D2O sphere and establish the neutron radiation field for the personal dosimetry performance test in Central Research Institute of KHNP, the neutron spectra have been simulated by MCNP 6.2 code by design conditions and evaluated dose conversion coefficients. In the consideration of neutron irradiation facility, the basic design structure was determined a D2O sphere with a diameter of covered with a Cd shell and a cylindrical well is in the middle of sphere. Neutron source transfer tube is inserted into this well-shaped structure and neutron source was withdrawn from the tube. And by changing the following design conditions in detail, the neutron spectra were evaluated; 1) the entire diameter of the D2O sphere (with or without the diameter of 7.5 cm of well-shaped structure) 2) the location of the neutron source (distance from D2O) 3) thickness of Cd shell 4) purity of D2O. As a source spectrum, the spectrum of bare- 252Cf recommended by ISO 8529-1 was adopted and spectra were tallied using F4 tally at a distance of 120 cm from the neutron source. Finally, the fluence to dose conversion coefficients were calculated using the simulated spectra. As a result of the evaluation, in case that an entire diameter of the D2O sphere with a diameter of the source tube is 37.5 cm, the fluence to dose conversion coefficient was evaluated to about 4.4% lower than an entire diameter of the D2O sphere is 30 cm. And in case that the distance between the D2O and the top of the neutron source was about 3.75 cm which is a radius of well-type structure, it was evaluated to about 1.4% larger than the distance was about 1 cm, and when the thickness of Cd was 0.1 cm, it was evaluated to 0.8% larger than when it was 0.051 cm. Finally, when the purity of D2O was 99.99%, it was evaluated 1.5% lower than when it was 99%. Except for the diameter of D2O sphere, the differences on the other conditions are acceptable considering the uncertainty of the simulation. Therefore, the design of D2O-moderated 252Cf source was determined by considering source integrity, economic perspectives, and dose conversion coefficient given in ISO 8529: a D2O sphere with an entire diameter of 37.5 cm, filled with above 99% purity of D2O, and covered with a cadmium thickness of 0.1 cm. The fluence to dose conversion efficient was evaluated as 110.10 pSv cm2 for ambient dose H*(10), 115.21 pSv cm2 for personal dose Hp(10) respectively.

Abstract In this study, micro-defects on/in carbon fibers were modified by irradiation with an electron beam, which improved the mechanical strength of single carbon fibers. The electron beam irradiation was 10 kGy (using a 1.5 MeV accelerator in the air). The total doses ranged from 100 to 500 kGy. The tensile strength of the single carbon fiber was measured using a universal testing machine. The micro-defects on the fiber surface were observed with scanning electron microscopy and atomic force microscopy, and those in the fiber were evaluated by Raman spectroscopy. In conclusion, the electron beam treatment produced changes in the micro-defects on/in the carbon fibers, resulting in up to 14% improvement in the tensile strength of single carbon fiber.

Several species of the genus Pseudo-nitzschia produce the neurotoxin domoic acid (DA) known to be responsible for amnesic shellfish poisoning. Recently off the coast of Geomundo and in Exclusive Economic Zone (EEZ) of Korea Strait, P. cf. brasiliana predominated in summer, 2010. As P. cf. brasiliana was new to Korea, we describe the morphological characteristics of the species. It was observed that cells were linear to lanceolate in valve and girdle view, 51~76 μm long and 1.9~2.6 μm wide. In the central part a large interspace was absent. The number of fibulae and striae in 10 μm were 30~37 and 31~37. Each stria contained 2~3 rows of poroids, with 10 to 14 poroids in 1 μm length. These morphological features of P. cf. brasiliana were found to be similar with the P. brasiliana, except with the fact that P. cf. brasiliana carred more numbers of fibulae/striae in 10 μm and poroids in 1 μm. Based on our observation, we suggest that P. cf. brasiliana is a newly identified Pseudo-nitzschia species or a variety of P. brasiliana.

This paper is to study the energy absorption characteristics of CF/Epoxy(Carbon Fiber/Epoxy Resin) laminated shell with the various curvatures subjected to transverse impact loadings under the low impact velocity in consideration of design of structural members for use of transportation machine, which are consisted of the characteristics of high stiffness, strength and lightweight. The curvature radius are associated with the energy absorption characteristics of CF/Epoxy laminated shell which is brittleness material. In all tests, maximum load of CF/Epoxy laminated plate is higher than that of laminated shell with curvature, but maximum deflection is lower. And then absorbed energy of laminated shell with curvature is higher than laminated plate(curvature radius is unlimited). As curvature radius is increased, the absorbed energy is increased in laminated shell with curvature.

본 연구에서는 PDMS (poly-dimethylsiloxane)와 PEBAX (polyether block amides) 분리막을 이용해 N2, O2, CF4와 SF6의 단일 기체 투과특성에 관하여 연구하였다. 다양한 압력으로 공급된 기체의 투과유량을 진공가압 연속흐름방식으로 측정하였으며, 이를 이용하여 투과도를 산정하였다. PDMS 분리막에서는 상부의 압력이 증가할수록 SF6를 제외한 다른 기체의 투과도는 감소하였다. 또한 SF6의 투과도가 CF4보다 높게 나타나고 있으며 이것은 SF6가 더 높은 임계온도를 가지고 있기 때문이다. PDMS 분리막에서 투과도는 O2 > N2 > SF6 > CF4 순으로 감소하였다. 반면에 PEBAX 분리막에서 기체의 투과 경향은 O2 > N2 > CF4 > SF6 순으로 감소하였다. 이러한 경향은 각 기체의 운동 반경의 크기(AA)(SF6 > CF4 > N2 > O2) 순서와 반대로 나타났다. SF6/CF4의 순수 기체의 선택도는 PDMS 분리막에서 0.7 MPa일 때 2.1로 나타났다.

중공사 고분자 분리막을 이용한 SF6를 분리 농축을 위한 운전조건을 결정하기 위해서는, 온도와 압력이 투과특성에 미치는 영향에 관한 연구가 필요하다. 본 연구에서는 다양한 온도와 압력이 부과된 조건에서 단일기체 투과실험을 수행하여, 중공사 고분자 분리막(PSF, PC, PI)을 통한 기체(N2, O2, SF6, CF4)의 투과특성을 연구하였다. 실험결과, 기체의 투과플럭스는 온도와 압력의 증가에 따라 일반적으로 증가하는 것으로 나타났으나, 분리막에 따른 투과플럭스의 차이가 관찰되었으며, 온도, 압력에 따른 투과플럭스 변화율은 기체의 특성(분자크기)에 따라 다른 것으로 나타났다. 온도 압력에 대한 투과플럭스를 3차원적으로 표현했을 때, 투과플럭스는 근사적인 평면 위에서 변화하는 것으로 관측되었다. 온도와 압력에 의한 투과플럭스 변화를 열역학적으로 분석하였으며, 투과플럭스 예측을 위한 경험적 모델로 평면특성의 1차 다항식 모델과 곡면 특성을 가진 2차 다항식 모델을 제안하였다. 그 결과 두 경험적 모델 모두 관측자료에 대한 높은 적합도를 보여 적용가능성을 확인하였다.

중전기의 유지 보수 및 교체 과정에서 절연체로 사용된 SF6 가스는 교체 충전과 정제과정에서 유입되는 공기와의 아크 방전에 의해 많은 종류의 부산물(N2, O2, CF4, SO2, H2O, HF, SOF2, CuF2, WO3 등)이 발생된다. 부산물 중에서도 대부분을 차지하는 것이 N2, O2, CF4이며, SF6가스를 재사용하기 위해서는 이들을 효과적으로 분리 회수하는 공정이 필요하다. 주요 부산물인 N2, O2, CF4와의 분리 효율 측면에서 분리막법은 기존의 흡착, 심냉법에 비하여 상대적으로 높은 효율을 보이고 있어 이에 대한 관심 또한 증가하고 있다. 따라서 본 논문에서는 중전기 산업에서 발생되는 SF6 가스 함유 농도 90 vol% 이상의 가스에 대하여 분리막법을 적용하여 N2, O2, CF4와 SF6 가스의 온도와 배출유량의 변화에 따른 분리 회수 가능성을 관찰하였다. PSF와 PC 중공사 분리막을 이용하여 고농도 SF6에 대한 분리 회수 실험 결과, PSF 분리막의 최대 회수율은 압력 0.3 MPa, 온도 25℃, 배출유량 150 cc/min에서 92.7%를 나타내었으며, PC 분리막에서는 압력 0.3 MPa, 온도 45℃, 배출유량 150 cc/min 일 때 74.8%의 최대 회수율을 나타내었다. 또한, 사용된 두 가지 분리막과 운전 조건에서 주요 부산물인 N2, O2, CF4의 최대 제거율은 각각 약 80%, 74%, 그리고 58.9%가 관찰되었다. 이로부터 분리막 공정은 고농도 폐 SF6 가스에서 주요 부산물로부터 SF6의 효과적인 분리 및 회수가 가능한 공정으로 적용할 수 있는 가능성을 파악 할 수 있었다.

IPCC (Intergonvernmental Pane1 of Climate Change)에서 CO2의 23,900배에 해당하는 지구온난화지수를 가진 SF6 (Sulphur hexafluoride) 가스와 중전기 산업에서 아크 발생에 의해 생긴 SF6의 주요 분해 부산물 중 하나이며 CO2의 6,300배에 해당하는 지구온난화지수를 가진 CF4 (Tetrafluoromethane) 가스의 배출에 대한 규제가 적극 검토되고 있다. 본 연구는 O2, CF4에 대한 SF6의 분리 회수의 기초 연구로써, 상용화된 PSF (polysulfone), PC (tetra-bromo polycarbonate)와 PI (polyimide) 고분자 분리막을 사용하여 O2, CF4와 SF6 가스의 압력과 온도 변화에 따른 투과도 및 투과선택도 연구를 수행하였다. 압력 변화에 따른 O2의 투과도는 PSF 중공사 분리막에서 압력 1.1 MPa일 때, 37.5 GPU로 가장 높게 나타났고, SF6와 CF4의 경우 압력 1.1 MPa에서 PC 중공사 분리막이 각각 2.7 GPU와 2.5 GPU로 가장 높은 투과플럭스를 나타냈다. 온도 변화에 따른 O2의 투과플럭스는 막의 온도가 45℃일 때 PSF 중공사 분리막이 41.2 GPU로 가장 높게 나타났고, SF6와 CF4는 막의 온도가 25℃일 때, PC 중공사 분리막이 각각 2.4 GPU와 2.3 GPU로 가장 높은 투과플럭스를 나타냈다. 압력과 온도 변화에 따른 O2/SF6와 CF4/SF6의 투과선택도 결과, 높은 단일 기체 투과플럭스를 보인 PSF와 PC 중공사 분리막이 가장 낮은 투과선택도를 나타내고, 가장 낮은 투과플럭스를 보인 PI 중공사 분리막이 가장 높은 투과선택도를 나타냄을 확인할 수 있다.

This paper is to study the energy absorption characteristics of CF/Epoxy(Carbon Fiber/Epoxy Resin) laminated shell with the various curvatures subjected to transverse impact loadings under the low impact velocity in consideration of design of structural members for use of transportation machine, which are consisted of the characteristics of high stiffness, strength and lightweight. The curvature radius are associated with the energy absorption characteristics of CF/Epoxy laminated shell which is brittleness material. In all tests, maximum load of CF/Epoxy laminated plate is higher than that of laminated shell with curvature, but maximum deflection is lower. And then absorbed energy of laminated shell with curvature is higher than laminated plate(curvature radius is unlimited), As curvature radius is increased, the absorbed energy is increased in laminated shell with curvature.

The surface treatment of C-type isotropic pitch-based carbon fiber was carried out by anodic oxidation in 5 wt% NH4NO3 electrolyte. The changes of fiber surface and carbon fiber/ABS resin composites were characterized by SEM, XPS and mechanical properties test. The oxygen functional groups on the surface, such as hydroxyl (-C-OH), carboxyl (-COOH) groups etc., increased after oxidation. Tensile strength, flexural strength and modulus of carbon fiber/ABS composites were also enhanced. However, the impact strength decreased with the improvement of the surface adhesion between CF and matrix.

PFC (perfluorocompound) gases have an extremely high global warming potential (GWP). A study of the destruction of NF3, CF4 and SF6 gases emitted from the semiconductor industry was attempted by plasma power at 4.4 kW, 5.5 kW, 6.0 kW, 6.6 kW, 7.6 kW, 8.1 kW and 9.1 kW. As electric power increased, DRE (destruction and removal efficiency) of NF3, CF4 and SF6 was also increased. It was confirmed through experiment that the DRE of NF3 is 99% at 7.6 kW, 97% for CF4 at 9.14 kW and 100% for SF6 at 7.6 kW of plasma power. By-products formed by PFC destruction were mainly F2, SO2F2, NOx and CO gases. In addition, particulate matter was formed, and particle were proven to be AlF3.

TV CF는 방송 프로그램의 시작과 중간 또는 끝 부분에 간단명료하게 메시지를 전달해야하는 절제된 영상으로, 수용자들 은 이를 통해 시장에 존재하는 제품에 관한 정보를 얻을 수 있고 어려운 판단의 기준으로 삼는다. 박카스는 오랜 기간 동안 TV광고를 통하여 상품이 아닌 시대의 트렌드를 반영하며 수용자들에게 공감과 찬사를 얻고 있으며 국민 광고로서 확고한 지위를 갖고 있다. 지난 2016년 3월부터 시작한 박카스의 새로운 캐페인 ‘나를 아끼자’의 ‘콜센터편’ ‘좋더라편’ ‘아껴서편’ 그리고 ‘생일파티편’까지 총 4편의 TV CF는 20대 젊은 세대들에게 위로와 응원의 메시지를 희망적으로 전달하였는데, 특 히 ‘콜센터편’은 이 시리즈의 첫 작품으로 광고 시작 1년 6개월이 지금까지도 계속해서 수용자들에게 회자되고 기억되고 있다. 이 연구에서는 ‘콜센터편’을 통하여 박카스 광고의 성공 이유와 차별점이 무엇인지를 살펴보고, 소비자 행동 이론을 모태로 한 수용자 정보처리과정을 활용하여 연구의 분석을 시도하고 있다. 수용자 정보처리 과정(Information Process)은 우연적이든 의도적이든 수용자가 노출된 광고에 주의를 기울이고 그 내용을 이해하여 새로운 신념이나 태도를 형성하거나 변화시키는 과정을 노출, 주의, 이해, 기억의 4단계로 구성하고 있다. 연구의 구성은 우선 수용자의 정보처리의 요인과 이 론적 논의를 진행하고, 이어서 ‘콜센터편’을 각각 노출, 주의, 이해, 기억의 단계로 세부적으로 분석하고 있다. 마지막 장에 서는 이를 통해서 수용자의 의사결정과정과 저장된 기억이 상품의 브랜드 이미지에 영향을 미칠 수 있는지 확인하고, 더불 어 수용자 정보처리과정이 TV광고의 분석 도구로서의 가능성을 살펴보고 있다.

A parametric study has been made numerically on the thermal incineration of CF4, one of the perfluorocarbons (PFCs) emerging recently as issues of public concern in a practical CDM incinerator developed for the thermal destruction of HFC-23. In doing this, a turbulent combustion model of the fast combustion approximation is reasonably assumed using the typical auxiliary fuel, CH4, for the supply of the heat, and the necessary species of hydrogen and oxygen atom. In addition, the performance of the stoichiometric gas mixture of hydrogen and oxygen (H2+ 1/2 O2) was examined as a special auxiliary fuel not only in order to enhance the thermal destruction efficiency but also the reduction of the CO2 emission by the elimination or the reduction of the auxiliary fuel CH4 in this incineration process. The calculation results showed that the thermal destruction efficiency of CF4 using methane as an auxiliary fuel increases with the amount of methane. However, the thermal destruction efficiency did not reach a satisfactory level (i.e., < 95%), even with the application of a CH4 amount more than four times of the stoichiometric value. This is explained by the improper turbulent mixing effect between CH4, CF4 and air especially in a large scale practical incinerator employed for the destruction of HFC-23. For the case of H2+ 1/2 O2 as the auxiliary fuel, however, the thermal destruction efficiency, surprisingly, reached almost 100%, which shows the high potential of the thermal destruction of CF4 by the use of HHO gas. Further, a detailed evaluation for the effect of the turbulent mixing on the thermal destruction of CF4 will be quite necessary, considering operating conditions together with the type of auxiliary fuels.

FRP reinforcement method is superior in safety and economic terms, but it's appears rapid degradation due to brittle fracture of reinforcing material. To solve this problem, study for PET sheet as reinforcement material was conducted by existing FRP reinforcement method. An experimental test was carried out by the amount of reinforcement and reinforcement types as the primary variable. As a results of this test, PET sheet appears ductility enhancement without rapid degradation. Consequently, it is judged that PET sheet is available to apply the field application.

Leaf mold disease in tomato (Solanum lycopersicum) is caused by Cladosporium fulvum, a fungal leaf pathogen. One of effective ways to control leaf mold is to breed disease-resistant tomato cultivars. Cf-4 and Cf-9 resistance (R) genes encode proteins that carry a leucine rich repeat domain and are located in plasma membrane. They trigger hypersensitive response following recognition of corresponding Avr4 and Avr9 proteins of C. fulvum, respectively. Cf-4 and Cf-9 genes are originated from wild tomato species S. habrochaites and S. pimpinellifolium and have been introgressed into commercial tomato cultivars. These two highly homologous orthologs exist as a cluster with four highly homologous paralogs. Due to this reason, development of genetic markers to distinguish these two functional R genes from their orthologs and paralogs is difficult. In this study, we tried to develop single-nucleotide polymorphism (SNP) markers to select tomato cultivars carrying resistant Cf-9 genotype. The genomic sequences of resistant Cf-4 and Cf-9 alleles, susceptible cf-9 alleles, and their paralogs were obtained from the GenBank database, and two functional SNPs causing non-synonymous substitution were found among them. Based on two SNPs, the Cf-9_2-SNP-F/R primer set for high resolution melting (HRM) analysis was developed. HRM analysis with this primer set could successfully distinguish tomato cultivars carrying resistant Cf-9 allele among 30 commercial tomato cultivars, which were characterized with the gene-based marker. These indicate that the SNP marker developed in this study is useful to trace Cf-9 genotype efficiently in marker-assisted selection in tomato.