The study used the whole-life carbon assessment method to conduct a thorough carbon-neutral evaluation of a standard steel structure. To further assess carbon emissions, 11 design-changed models were evaluated, with changes made to the span between beams and columns. The results of the carbon emission assessment showed savings of approximately 13.1% by implementing the stage of the beyond life cycle. Additionally, the evaluation of carbon emissions through design changes revealed a difference of up to 42.2%. These findings confirmed that recycling and structural design changes can significantly reduce carbon emissions by up to 48.6%, making it an effective means of achieving carbon neutrality. It is therefore necessary to apply the stage of beyond life cycle and structural change to reduce carbon emissions.

A smart tuned mass damper (TMD) was developed to provide better control performance than a passive TMD for reduction of earthquake induced-responses. Because a passive TMD was developed decades ago, optimal design methods for structural parameters of a TMD, such as damping constant and stiffness, have been developed already. However, studies of optimal design method for structural parameters of a smart TMD were little performed to date. Therefore, parameter studies of structural properties of a smart TMD were conducted in this paper to develop optimal design method of a smart TMD under seismic excitation. A retractable-roof spatial structure was used as an example structure. Because dynamic characteristics of a retractable-roof spatial structure is changed based on opened or closed roof condition, control performance of smart TMD under off-tuning was investigated. Because mass ratio of TMD and smart TMD mainly affect control performance, variation of control performance due to mass ratio was investigated. Parameter studies of structural properties of a smart TMD was performed to find optimal damping constant and stiffness and it was compared with the results of optimal passive TMD design method. The design process developed in this study is expected to be used for preliminary design of a smart TMD for a retractable-roof spatial structure.

In this study, a winch and load motion control system design method is introduced. Especially, the winch and load (moving cart) are connected with long wire rope which is extended to few kilometers long. Therefore, the rope length changes such that many dynamic parameter values are changed as well by winding and releasing the rope from the winch system. In this paper, the authors designed the control system by considering the real time parameter variation to occupy and keep good control performance continuously. The effectiveness of introduced method was evaluated by simulation results.

This study investigates on the tuning stainless steel(STS630) to understand for groove cutting characteristics. For this purpose, we observed the cutting force according to feed rate and cutting speed variation and performed the computational analysis due to groove cutting depth. In groove cutting of stainless steel, there were principal force, feed force and radial force by arranging the highest cutting force in order. In case of wall thicknesses of 0.3mm and 0.5mm at groove cutting, principal force increases according to the increase of feed rate but it is not related to cutting speed. We found the unstable region of cutting force that is caused to the friction resistance of cutting tool and elastic deformation of groove wall. In computational analysis, we confirmed that the more feed rate increases, the more strain increases around the tooth root.

In the manufacturing industry fields, thousands of quality characteristics are measured in a day because the systems of process have been automated through the development of computer and improvement of techniques. Also, the process has been monitored in database in real time. Particularly, the data in the design step of the process have contributed to the product that customers have required through getting useful information from the data and reflecting them to the design of product. In this study, first, characteristics and variables affecting to them in the data of the design step of the process were analyzed by decision tree to find out the relation between explanatory and target variables. Second, the tolerance of continuous variables influencing on the target variable primarily was shown by the application of algorithm of decision tree, C4.5. Finally, the target variable, loss, was calculated by a loss function of Taguchi and analyzed. In this paper, the general method that the value of continuous explanatory variables has been used intactly not to be transformed to the discrete value and new method that the value of continuous explanatory variables was divided into 3 categories were compared. As a result, first, the tolerance obtained from the new method was more effective in decreasing the target variable, loss, than general method. In addition, the tolerance levels for the continuous explanatory variables to be chosen of the major variables were calculated. In further research, a systematic method using decision tree of data mining needs to be developed in order to categorize continuous variables under various scenarios of loss function.

Recently, the production cycle in manufacturing process has been getting shorter and different types of product have been produced in the same process line. In this case, the control chart using coefficient of variation would be applicable to the process. The theory that random variables are located in the three times distance of the deviation from mean value is applicable to the control chart that monitor the process in the manufacturing line, when the data of process are changed by the type of normal distribution. It is possible to apply to the control chart of coefficient of variation too.  ,  estimates that taken in the coefficient of variation have just used all of the data, but the upper control limit, center line and lower control limit have been settled by the effect of abnormal values, so this control chart could be in trouble of detection ability of the assignable value. The purpose of this study was to present the robust control chart than coefficient of variation control chart in the normal process. To perform this research, the location parameter, xα, sα were used. The robust control chart was named Tim-CV control chart. The result of simulation were summarized as follows; First, P values, the probability to get away from control limit, in Trim-CV control chart were larger than CV control chart in the normal process. Second, ARL values, average run length, in Trim-CV control chart were smaller than CV control chart in the normal process. Particularly, the difference of performance of two control charts was so sure when the change of the process was getting to bigger. Therefore, the Trim-CV control chart proposed in this paper would be more efficient tool than CV control chart in small quantity batch production.

In this study, cation and anion exchange process for performance evaluation was conducted. A pilot plant for the ultrpure water production was installed with the capacity of 25 m3/d. The various production rate and regeneration of ion exchange rate were tested to investigate the design parameters. The test resulst was applied to calculate the operating costs. Changing the flow rate of the ion exchange capacity of the reproduction reviewed the cation exchange process as opposed to the design value is 120 to 164% efficiency , whereas both anion exchange process is 82 to 124% efficiency, respectively. This results can be applied for more large scale plant if the scale up parameters are consdiered. The ion exchange capacity of the application in accordance with the design value characteristic upon application equipment is expected to be needed. In this study, the performance of cation and anion exchange resin process was evaluated with pilot plant(25m3/d). The ion exchange capacity along with space velocity and regeneration volume was evaluated. In results, the operation results was compared with design parameters.

Control charts are generally used for process control, but the role of traditional control charts have been limited in case of a contaminated process. Traditional x control charts have not been activated well for such a problem because of trying to control processes as center line and control limits changed by the contaminated value. This paper is to propose robust x control charts which is considering a location parameter in order to respond to contaminated process. In this paper, we consider x, that is trimmed rate; typically ten percent rate is used. By comparing with p, ARL value, the responding results are decided. The comparison resultant results of proposed two control charts are shown and are well contrasted.

When it comes to designing a product or a process, the robust parameter design (RPD) methodology devised by Taguchi is recognized as a way to produce products or processes with less variability, while the specifications of products or processes are met, so that the ratio of nonconforming products can be as minimized as possible. Nevertheless, as a matter of fact, there have been many pros and cons concerning the RPD method, mainly because of the use of signal to noise ratio as the measure of quality characteristic. Meanwhile, the variability analysis method has been highly recommended as an alternative of the RPD in the literature. In this paper, it is demonstrated that RPD can also be implemented within the framework of the variability analysis, which is sounder in the statistical sense. In light of an example of RPD approach, the modeling and estimation procedure is discussed in some detail with a view to a comparison of the two methods.

Stainless steel sheets are widely used as the structure material for the railroad cars and the commercial vehicles. These kinds structures used stainless steel sheets are commonly fabricated by using the gas welding. For fatigue design of gas welded joints such as fillet and plug and ring type joint, it is important to obtain optimum design parameter information on gas welded joints. In this paper, analysis approach for fatigue test using experimental design are evaluated optimum factor in gas welded joint type and geometrical parameters of materials. Using these results, that factors applied to fundamental information for fatigue design.

A variety of statistical methods are applied to model and optimize responses, related to product or system's quality, in terms of control and noise factors at design and manufacturing stages. Most of them assume continuous response variables but, assessin

본 연구의 목적은 첫째, 비선형성을 포함하는 액체기둥진동흡진기(LCVA)의 감쇠항에 대한 등가선형화된 운동방정식을 바탕으로하여 가진입력인 진동대 가속도와 출력인 제어력의 관계인 전달함수를 해석적인 식으로 규명하는 것이다. 둘째, LCVA의 주요설계변수인 수직기둥과 수평기둥의 단면적비의 변화에 따른 진동특성분석이다. 셋째, 동조의 수단으로 이용되는 수직기둥 액체의 높이를 변화시켜 진동특성을 분석하는 것이다. LCVA를 진동대 위에 설치하고 가진하여 제어력을 측정하여 실험 전달함수를 구하였다. 이것을 해석적인 전달함수와 비교 및 최적화작업을 수행하여 LCVA의 진동특성변수에 영향을 미치는 고유진동수, 감쇠비 및 질량비 등을 파악하였다. 실험결과, 액체 수위 및 단면적비의 변화에 따라 감쇠비 및 참여질량비의 특성이 변화하였다. 수직기둥과 수평기둥이 교차하는 엘보우에서 액체의 흐름 변화로 인하여, LCVA 실험체의 수직기둥 단면적이 작아질수록 감쇠비와 참여질량비가 증가하였다.

In this study, numerical analysis of TMD to estimate optimal-design-parameter is investigated using actual excitation, and evaluated by comparing results of numerical analysis and optimal-design-parameter was devised by Soong. It assumed between 1~2 seconds the 1st mode natural period of an aged apartment which has 10~15 stories and then investigated optimal-design-parameter of actual excitation for evaluate optimal frequency ratio and damping ratio according to local site condition. At this time mass ratio was 1% and range of tuned frequency ratio was 0.8Hz to 1.2Hz at intervals of 0.01Hz, and optimal damping ratio was 1% to 14% at intervals of 0.002%. It estimated Optimal-design-parameter was evaluated by numerical analysis according to peak and RMS displacement, acceleration respectively local site. And the result of evaluated respond performance parameter respectively a period was shown low numerical-value than optimal-design-parameter was devised by Soong what is more peak acceleration indicated performance difference of 20% over

There is boner process of stone manufacturing to become quality down of stone to consolidated micro crack appearance of stone surface and biotite by fire that is to be route process in stone surface by flame of LPG. And then, it is develop that stone surface process equipment by automation for the work method of boner process can be substitute work method by shotball blasting. To developement of equipment, There is to be down noise and dust. Acording to remove calamity growth hazardous substance in the work environment, there is to solve workplace avoidance factor. We have taken Taguchi's parameter design approch, specifically orthogonal array, and determined the optimal levels of stone surface through analysis of the experimental results using SIN ratio.

A study to analyze and solve problems of a stone surface process experiment has presented in this paper. We have taken Taguchi's parameter design approach, specifically orthogonal array, and determined the optimal levels of the selected variables through analysis of the experimental results using S/N ratio.

이 논문에서는 지하식 LNG 저장탱크의 설계조건 변화에 따른 구조거동에 대한 사례연구를 다루었다. 지하식 LNG 저장탱크의 설계에 있어서, 치적의 탱크 형상과 치수를 결정하는 것은 다양한 하중조건과 이들의 하중조합 하에서 더욱 향상된 구조거동을 위해 매우 중요하다. 저장 탱크의 설계단계에서 유지단계에 이르기까지 구조거동에 영향을 미치는 주요인자에 대한 분석과 평가가 이루어졌으며, 이러한 매개변수연구를 토대로 한 결과에 근거하여 지하식 LNG 저장탱크의 보다 합리적인 설계에 대한 기초자료를 제안하였다.

Polyacetal resin is usually used to make molds, but it is difficult to achieve dimension accuracy during molding. Therefore it is usually necessary to cut the polyacetal resin after a molding process. Polyacetal resin is easily machining by standard machine tool. Acetal is also a thermal stable material which can be totted without coolant Another concern about the use of polyacetal resin is that it absorbs water easily, which also results in problems with dimension accuracy Therefore, in this study, the cutting resistance of water-absorbed polyacetal resin and its surface roughness after cutting in order to achieve the highest degree of accuracy in the cutting of polyacetal resin were investigated. Also, The Robust Design method uses a mathematical tool called orthogonal arrays to study a large number of decision variables with a small number of experiments. It also uses a new measure of quality, called signal-to-noise (S/N) ratio, to predict the quality from the customer's perspective. Thus, we have taken Taguchi's parameter design approach, specifically orthogonal array, and determined the optimal levels of the selected variables through analysis of the experimental results using S/N ratio.

The critical problem in dealing with multiple characteristics is how to compromise the conflict among the selected levels of the design parameters for each individual characteristic. In this study, First, Methodology using SN ratio optimized by univariate technique is proposed and a parameter design procedure to achieve the optimal compromise among several different response variables is developed. Second, to solve the issue on the optimal design for multiple quality characteristics, this study modelled the expected loss function with cross-product terms among the characteristics and derived range of the coefficients of the terms. The model will be used to determine the global optimal design parameters where there exists the conflict among the characteristics, which shows difference in optimal design parameters for the individual characteristics. Third, this paper propose a decision model to incorporates the values assigned by a group of experts on different factors in weighting decision of characteristic. Using this model, SN ratio of taguchi method for each of subjective factors as well as values of weights are used in this comprehensive method for weighting decision of characteristic.