Ring Tensile Test (RTT) is mainly performed for comparing tensile strength and total strain between nuclear fuel cladding specimens under various initial conditions. Through RTT, the loaddisplacement (F-D) curve obtained from the uniaxial tensile test can also be obtained. However, the Young’s modulus estimated from the gradient of the straight portion is much lower than general value of materials. The reasons include tensile machine compliance, slack in the fixtures, or elastic deformation of the fixtures and the tooling. Another reason is that the bending of the test part in the ring is stretched with two pieces of tools. Although the absolute value of the Young’s modulus is smaller than the actual value, it is applicable to calculate the ratio of the Young’s moduli of different materials, that is, the relative value. The Young’s modulus, or slope of the linear section, varies slightly depending on which location data is used and how much data is included. In order to obtain a more accurate ratio of Young’s moduli between materials using the RTT results, a post-processing method for the ring tensile test results that can prevent such human errors is proposed as follows. First, the slope of the linear section is obtained using the displacement and load when the load increase is the largest and the displacement and load of the position that is 95% of the maximum load increase. To replace the section where the ring-shaped specimen is stretched at the beginning of the F-D curve, a straight line equal to the slope of the linear section is drawn to the displacement axis from the position of maximum load increase and moved to the origin to obtain the final F-D curve for a RTT. Lastly, the yield stress uses the stress at the point where the 0.2% offset straight line and the F-D curve meet as suggested in the ASTM E8/E8M-11 “Standard test methods for tensile testing of metallic materials”. RTT results post-processing method was coded using FORTRAN language so that it could be performed automatically. In addition, sensitivity analysis of the included data range on the Young’s modulus was performed by using the included data range as 90%, 85%, and 80% of the maximum load increase.

신안군 해역의 섬을 통한 관광사업이 활발해지면서 도서 간을 연결하는 해상교량은 현재까지 총 13개가 완공되었다. 그러나 통항로에 설치된 해상교량은 선박통항에 있어 위험성을 주며, 특히 섬과 섬을 연결하는 연도교의 경우 수로의 폭이 매우 좁아 그 위험도 는 더욱 높다. 본 연구는 신안군 해역의 연도교에 대한 해상교통조사를 토대로 교각과 선박의 충돌위험도를 항만수로의 위험도 평가 모 델인 IWRAP(IALA Waterway Risk Assessment Program)을 활용하여 평가하였다. 그 결과 신안1교가 충돌확률이 가장 높은 것으로 분석되었으 며, 통항선박의 대부분은 연안 여객선으로 나타났다. 또한, 신안1교는 대상해역의 교각 중 가장 충돌사고가 많이 발생한 곳으로 본 연구 에서는 그 원인을 분석하고자 하였다. 신안1교 해역환경의 위성사진을 영상처리기법으로 분석한 결과 해도에는 볼 수 없는 장애물이 교 량 근처에 존재하는 것을 확인할 수 있었다. 이로 인해 장애물을 피해 교량의 통항유도방식인 양방향 통항과 달리 한 방향으로 통항이 집 중되는 것을 알 수 있었다. 본 연구의 영상처리기법을 활용한 위험원인 분석방법은 향후 연도교의 위험요인 분석을 하는데 기초자료로 활용될 수 있을 것으로 기대된다.

Heavy bitumen scattered in the underground sedimentary layer is a kind of unconventional energy source, and by extracting it, a production well is excavated in the sedimentary layer and high-temperature and high-pressure steam is injected to reduce the viscosity of bitumen and recover it to the ground steam assisted method is applied. As a recovery method that uses the steam effect of the dilution effect of solvent injection, it is a recovery method that can increase thermal efficiency. In this study, the process system of the central processing facility(CPF) of the hybrid steam-solvent recovery method that injects solvent into the existing steam assisted method was analyzed, and the core facilities for each process were identified, and hybrid steam-solvent recovery compared to the existing steam assisted method. In the case of the method, it was evaluated that the amount of steam supply and all utility costs decreased according to the solvent injection.

In this experiment, the error according to the measurement method was analyzed for the length, angle, radius of curvature, and diameter of the measurement system analysis using a profile projector device used in the field. One-way analysis was performed on each data tested 30 times using a statistical technique. Through the experiment, it was found that an error occurred in each data when measuring the angle according to the measurement method, and the null hypothesis that no error occurred when measuring the length, inside dia and radius was established.

본 연구에서는 영상기반 딥러닝 및 이미지 프로세싱 기법을 이용한 볼트풀림 손상검출 기법을 제안하였다. 이를 위해 먼저, 딥러닝 및 이미지 프로세싱 기반 볼트풀림 검출 기법을 설계하였다. 영상기반 볼트풀림 검출 기법은 볼트 이미지 검출 과정 및 볼트풀림 각도 추정 과정으로 구성된다. 볼트 이미지의 검출을 위하여 RCNN기반 딥러닝 알고리즘을 이용하였다. 영상의 원근왜곡 교정을 위해 호모그래피 개념을 이용하였으며 볼트풀림 각도를 추정을 위하여 Hough 변환을 이용하였다. 다음으로 제안된 기법의 성능을 검증을 위하여 거더의 볼트 연결부 모형을 대상으로 볼트풀림 손상검출 실험을 수행하였다. 다양한 원근 왜곡 조건에 대하여 RCNN 기반 볼트 검출기와 Hough 변환 기반 볼트풀림 각도 추정기의 성능을 검토하였다.

In this study, a multifunctional ophthalmic lens material with an electromagnetic shielding effect, high oxygen permeability, and high water content is tested, and its applicability is evaluated. Metal oxide nanoparticles are applied to the ophthalmic lens material for vision correction to shield harmful electromagnetic waves; the pyridine group is used to improve the antibacterial effect; and silicone substituted with urethane and acrylate is employed to increase the oxygen permeability and water content. In addition, multifunctional tinted ophthalmic lens materials are studied using lens materials with an excellent antibacterial effect (2,6-difluoropyridine, 2-fluoro-4-pyridinecarboxylic acid) and functional (UV protection, high wettability) lens materials (2,4-dihydroxy benzophenone, 2-hydroxy-4-(methacryloyloxy)benzophenone). To solve problems such as air bubbles generated during the polymerization process for the manufacturing and turbidity of the lens surface, polymerization conditions in which the defect rate is minimized are determined. The results show that the polymerization temperature and time are most appropriate when they are 110 oC and 40 minutes, respectively. The optimum injection amount of the polymerization solution is 350 ms. The turbid phenomenon that appears in lens processing is improved by 10 to 95% according to the test time and conditions.

Self-assembled monolayers(SAM) of microspheres such as silica and polystyrene(PS) beads have found widespread application in photonic crystals, sensors, and lithographic masks or templates. From a practical viewpoint, setting up a highthroughput process to form a SAM over large areas in a controllable manner is a key challenging issue. Various methods have been suggested including drop casting, spin coating, Langmuir Blodgett, and convective self-assembly(CSA) techniques. Among these, the CSA method has recently attracted attention due to its potential scalability to an automated high-throughput process. By controlling various parameters, this process can be precisely tuned to achieve well-ordered arrays of microspheres. In this study, using a restricted meniscus CSA method, we systematically investigate the effect of the processing parameters on the formation of large area self-assembled monolayers of PS beads. A way to provide hydrophilicity, a prerequisite for a CSA, to the surface of a hydrophobic photoresist layer, is presented in order to apply the SAM of the PS beads as a mask for photonic nanojet lithography.

This study introduces the web-camera image processing-based natural landmark extraction method for automatic welding using 3-axis stage. The welding is a highly significant process in the industries of shipbuilding, automobile, construction, machinery, and so on. However, it has been avoided due to poor working conditions such as fume, spatter, noise, and so on. For the automatic welding system, the web-camera is used to extract the natural landmarks which can give the relative coordinate to set up the initial position of the stage for the welding process. The Canny edge and Hough transformation have been used to extract the significant points for the natural landmark extraction in this paper.

Tin oxide nanoparticles (n-SnO and ) were synthesized by the inert gas condensation (IGC) method under dynamic gas flow of oxygen and argon at various conditions. Transmission electron microscopy (TEM) and X-ray diffraction (XRD) method were used to analysis the size, shape and crystal structure of the produced powders. The synthesized particles were mostly amorphous and their size increased with increasing the partial pressure of oxygen in the processing chamber. The particles also became broader in size when higher oxygen pressures were applied. Low temperature annealing at in air resulted to crystallization of the amorphous n-SnO particles to .

기선장에 따른 GPS 위치 정도 및 분포를 측정하기 위하여 2002년 5월 29일부터 6월 2일까지 2대의 GPS수신기 (L1, 12채널)를 이용하여 고정점에서 30분에서 24시간동안 관측하는 실험을 수행하였다. 기준국(PKNU)과 이동, 국립지리원의 GPS 상시관측소에서 수신한 GPS 데이터는 동적 및 정적 후처리방식으로 처리하였으며, 그 결과를 요약하면 다음과 같다. 1. 2002년 5월 31일 차단각 (cut-off angle) 15˚에서 6시간 이상 관측 가능한 위성은 16개였고, 위성은 주로 동서방향으로 배치되어 있었다. 10분마다 평균한위성 수와 GDOP는 각각 8개, 3.89이었다. 2. 후처리 전후의 GPS 평균위치는 모두 기준점에서 남서쪽으로 편위 (단독 측위 : 1.17m, 후처리 : 평균 0.43m)되었다. 확율원 오차는 단독 측위가 6.65m이었고 이를 동적 후처리하면 단독 측위의 약 33.8%(표준편차 0=17.2), 정적 후처리하면 단독 측위의 약 5.3% (0=2.2)로 감소시 킬 수 있었다. 3. 정적 후처리방식으로 구한 기선장 x(Km)와 확률원 오차 y(m) 의 관계식은 y = 0.0016x + 0006 (R2=0.87)이었다. 본 연구에서 사용한 1주파용 GPS 수신기를 이용하여 정적 후처리방식으로 위치를 측정하는 경우, 기선장을 100Km 이내로 하고 GPS 수신시간을 30분 이상으로 하면 확율원 오차 20 Cm 이내의 측위가 가능함을 알 수 있었다.

This study was conducted to investigate the application of ATP bioluminescence to measure the degree of microbial contamination from raw meat, meat processing and milk processing lines. Samples collected from slaughter house, meat and milk processing plants were tested for estimation of bacterial number by using ATP bioluminescence and conventional method. The former result was transffered to R-mATP value(log RLU/㎖), and the latter transffered to CFU(log/㎖). Correlation coefficient(r) between aerobic counts(CFU, log/㎖) and R-mATP(log RLU/㎖) value was 0.93(n=408). R-mATP of aerobic counts from beef, pork, chicken was 0.93(n=220), and that was 0.93(n=187) between meat processing and dairy processing plants. In addition, Correlation coefficient(r) between aerobic counts and R-mATP was 0.87(n=252) under 1 × 10^5/㎖ of bacterial count and 0.74(n=152) over l0^5 respectively.

This study was attempt to improve the quality of rapid- and low salt-fermented liquefaction of sardine (Sardinops melanoslicta). Effect of pretreatment methods such as water adding, heating, and intermittent NaCl adding on fermented liquefaction of chopped whole sardine were investigated. The divisions of the experimental samples by pretreatment methods were as follows; Sample A (water adding and heating): chopped whole sardine adding 20% water and then adding 3 and 5% NaCl consecutively at the intervals of 3 and 6 hrs during heating for 9 hrs at 50℃ and then fermented at 33℃ for 90 days. Sample B (preheating): chopped whole sardine with 8% NaCl and heating at 50℃ for 9 hrs and then fermented at 33℃ for 90 days. Sample C (control): neither pretreatment methods of water adding nor preheating on chopped whole sardine with 13% NaCl and then fermented at 33℃ for 90 days. Comparison of the appropriate fermentation period, yield of hydrolysate, chemical composition of fermented liquefied products were carried out. The highest content of amino nitrogen appeared at 60 days in the sample A, 75 days in the sample B, and 90 days in the sample C during the fermentation period. The appropriate fermentation period of the sample A was shorten 15 days than the sample B and 30 days than the sample C in the processing of sardine. The product A was lower NaCl (8.5%) and lower histamine content (25mg/100g) than the sample B and C. Possibly, three kinds of pretreatment methods such as water adding, heating, and intermittent NaCl adding, might be recommend as the processing of rapid- and low salt-fermented liquefaction product of chopped whole sardine.