PURPOSES : This study evaluates the noise reduction effects of various road paving methods and focuses on low-noise pavements as a cost-effective alternative to sound barriers and tunnels. In addition, this study assesses how noise levels vary with vehicle speed across different paving methods. METHODS : An analysis of variance (ANOVA) was conducted to evaluate the noise performance of different paving methods, and this followed by a post-hoc analysis to examine the differences among the paving methods. Another ANOVA was conducted to evaluate the impact of speed on noise performance. This ANOVA was followed by a post hoc analysis to assess differences by speed. Finally, a covariance analysis was conducted, using speed as a covariate, to evaluate the noise reduction effects of the various paving methods. RESULTS : The results of the analyses showed that noise levels follow the order of General ≈ Non-draining > Single-layer ≈ Doublelayer, thus grouping the paving methods into two categories with significant differences in noise performance. In addition, the noise levels increased with speed, except at 70 and 80 km/h. The covariance analysis resulted in a regression coefficient of 0.267 for speed across all paving methods. A post-hoc analysis grouped the paving methods into three distinct categories: General, Non-draining ≈ Single-layer ≈ Double-layer, with notable noise differences between them. CONCLUSIONS : The analysis of noise performance showed that both the paving method and speed significantly affected the noise levels. The covariance analysis, using speed as a covariate, revealed a consistent regression coefficient of 0.267 across all the paving methods. After controlling for speed, noise differences were observed. The General method showed higher noise levels than did the Non-draining, Doublelayer, and Single-layer methods.

최근 우리나라에는 도로 주변에 고층의 대규모 공동주택이 건설되는 사례가 증가하고 있고 저소음포장은 중요한 도로소음 대책 수단 중의 하나이다. 특히, 도로변의 공동주택이 고층이고 도로에 가까울수록 방음벽의 높이가 높아지거나 방음벽으로도 소음기준을 만족 시키지 못할 경우에는 터널형 방음벽이 설치되기도 한다. 이러한 경우 저소음포장은 좋은 해결책이 될 수 있지만 소음저감성능이 일정 하지 못하다는 단점이 있다. 본 연구에서는 저소음포장의 감음성능 평가를 위한 다양한 방법을 검토하고 이에 대해 고찰하였다., 한번 설치되면 소음저감성능이 거의 변하지 않는 방음벽에 비해 저소음포장은 사용 환경과 시간이 경과함에 따라 성능이 변화(경시변화)하는 단점을 가지고 있어 어느 정도의 저감량을 설정하여 소음대책에 적용하느냐가 중요한 문제로 대두되고 있다. 하지만, 동일한 재료와 공법으로 포설을 한다 하더라도 시공된 현장의 교통량과 주행속도, 대형차 비율 등 사용환경에 따라 소음저감성능의 경시변화가 달라질 것이라는 추측이 가능해 진다. 본 연구에서는, 도로교통소음 대책을 위해 저소음포장을 적용할 경우 포장 종류에 따라 적용할 소음저감 효과를 어떤 방법으로 평가하는 것이 타당할 것인지에 대해 검토하고자 하였다. 저소음포장 및 이와 인접한 일반포장이 시공된 고속도로 현장에서 CPX(Close-proximity) noise 측정 및 갓길 Pass-by noise 측정에 의해 일반포장과 저소음포장에서 발생하는 소음을 동시에 측정하고 그 차이를 비교하여 저소음포장의 소음저감효과를 평가하였다.

In this study, an experimental analysis of noise reduction in road traffic by applying the Micro Grooving technique to concrete highway pavements is explored. Initiated in 1984 to address the aging and damage issues observed in South Korea's concrete highways, Micro Grooving is known for creating fine grooves on the cement pavement surface to increase friction, prevent hydroplaning, and inhibit ice formation, while reducing vehicle friction noise by 3∼5dB(A). It is determined from noise measurement results that the application of the Micro Grooving method can be expected to reduce roadside noise and enhance the safety of drivers' driving experience.

Road surfaces and tires have a great influence on road noise in automobiles. Therefore, this study attempted to investigate the effect of changes in road surface and tire tread on road noise. For six road surfaces, road noise was measured and analyzed while changing two types of tire treads. In all frequency bands, the sound pressure of the road surface with a relatively large roughness was higher than that of other roads. And in the case of a road surface with relatively large pore, it was investigated that noise was reduced compared to other road surfaces due to the sound absorption effect in the low frequency area. On roads with irregular road roughness, the high sound pressure was exhibited in all frequency bands regardless of tire tread, indicating an increase in road noise due to irregular wear on roads. It was confirmed that the noise deviation due to the change in road surface was larger than the noise deviation due to the tire structure, and it is judged that noise research according to the structure and condition of the road surface.

Assessment of noise exposed population is to check the environment noise level and social influence in order to reduce the risks such as annoyance and disturbance that are generated by environmental noise. Also, this method suggests the preferential noise abatement policy and action plan by accurately finding the area that the noise causes harmful effect to human health. Recently, a noise map, which can predict noise in comprehensive area, is used for the assessment of noise exposed population, breaking from the methods using existing measures. In particular, countermeasure for noise can be considered more effectively by using assessment methods of noise exposed population for specific noise level, area and building types which are the main input factors in noise maps. In this study, we propose noise prediction at traffic noise due to noise map.

The object of this paper is to estimation of noise reduction effect of road noise by operating condition due to tire noise regulation. A prepare the countermeasure of the noise reduction according to collect tire/road noise data under various influencing factors by using the tire test method. To accomplish the object : A automotive is used as a test platform to test tire/road noise by changing different types of tires and using the On-Board Sound Intensity test system. The influence of inflation pressure, road, load, speed and pattern type on tire/road noise is compared and analyzed. At the same time, the mechanism of tire/road noise is analyzed, which provides an experimental basis for tire noise reduction.

PURPOSES : Exposed aggregate concrete pavements have been adopted in several countries because of their advantages of pavement texture characteristics, which can produce low tire-pavement noise and higher load-carrying capacities. The magnitude of tire-pavement noise greatly depends on the wavelength of pavement texture. The wavelength of exposed aggregate concrete pavement can be controlled with maximum sizing and by controlling the amount of coarse aggregates in the concrete mixture. In this study, the maximum size and the amount of coarse aggregate in the exposed aggregate concrete pavement are investigated to produce equal levels of wavelength in the asphalt pavement. METHODS: A simple method to measure the average wavelength of pavement texture is introduced. Subsequently, the average wavelength of typical asphalt pavement is investigated. A set of mixture designs of exposed aggregate concrete with three maximum-sized coarse aggregates, and three amounts of coarse aggregate are used. The average wavelengths are measured to find the mixture design needed to produce equal levels of wavelength as typical asphalt pavement. RESULTS : With a cement content of 420 kg/m3 and fine aggregate modulus of 30%, the number of exposed aggregates was 48, and the shortest texture depth provided a wavelength of 4.2 mm. According to the number of exposed aggregates, the exposed aggregate concrete pavement could be rendered low-noise, because its wavelength was similar to that of asphalt pavement ranging from 3.9 to 4.4 mm. CONCLUSIONS : Selection of appropriate maximum sizes and the amount of coarse aggregates for exposed aggregate concrete pavement can produce a wavelength texture closely resembling that of asphalt pavement. Therefore, the noise level of exposed aggregate concrete pavement can be reduced with an appropriate maximum size and the amount of coarse aggregates are employed.

In recent years, there have been applied methods for minimizing noise by adjusting the method of installing soundproof walls, soundproof tunnels, soundproofing rims, environmental facilities, etc., and the shape of the surface texture of tire treads and packaging materials for the purpose of reducing road noise. Low noise pavement methods such as rubber asphalt (CRM), open graded asphalt concrete (OGAC), permeable Friction Courses (PFC), open graded friction courses (OGFC) and porous asphalt have been applied to reduce road noise. Especially, porous pavement is the most widely used low noise pavement with porous structure, which can reduce noise and drain water through continuous void of pavement. On the other hand, porous asphalt pavement has problems such as reduction of noise reduction effect and difficulty of road surface management due to void closing and increase of construction cost. The purpose of this study is to develop ultra-thin layer hot mix asphalt pavement method which maximizes road noise reduction effect by surface micro voids (Recover asphalt pavement) to improve void clogging of present porous pavement method. For this study, maximum size 5mm aggregate and cationic-treated fiber reinforced asphalt modifier (CSM) were used. The Marshall design method was applied grain-size distribution curve was based on SMA mix design. Marshall test, TSR, MMLS3 test and Hamburg test were carried out to evaluate the mechanical properties of ultra -thin layered asphalt pavement method with surface micro voids. Also, the effect of road noise reduction was evaluated through field application in urban area.

PURPOSES : The computational fluid dynamics of flow and fine particles in a road were set to determine the insert flow and occurrence characteristics.METHODS: The road extension was 100 m with two lanes. A one-ton truck traveled a 50-m distance. After a noise barrier was installed on one side of the road, the flow and a collision analysis were tested.RESULTS: The flow that occurred was 5 m/s beside the vehicle, and fine particulate was 5.0×102 μg/m3 after 20 m from the exhaust vent.CONCLUSIONS: After a collision analysis of the fine particulate on the noise barrier to find the most suitable position of the filter panel in height, the bottom 1 m was the most optimum position because 88.1% of the distribution was concentrated there.

In contemporary society, vibration and noise in the road nearby buildings have become social problems as vehicles operation has increased. Especially, in the case of the building used to art performance, available suitability of the building is tested by the indoor noise class. Therefore, the purpose of this paper is the measurement of the structure-borne noise of Seoul Art Center nearby Umyeonsan tunnel and analyzing the effects of countermeasure to it. To measure the effects of countermeasure, not only structure-borne noise is measured, but also the vibration is measured, before and after the construction of pavement using pad and porous asphalt. Consequently, the sound pressure level in art center 1st floor is reduced after mat pavement method, structure-borne noise that was high in 25Hz wide-band before pavement decreased regardless of experimental vehicle's velocity. Using porous asphalt pavement the noise was reduced about 3 dB(A).

It is known that air pollutants such as fine dust and exhaust gas from vehicles are harmful to human health. In particular, the black carbon emitted by vehicles is known to cause a large number of premature deaths. This study analyzed the effect of a noise barrier on the inflow amount of black carbon from a nearby high traffic road to a school area, using numerical analysis performed at two elementary schools. Also, the correlation between the noise barrier’s shape, height and the inflow amount of black carbon was assessed. As a result, it was found that the higher the noise barrier, the lower the inflow amount of black carbon observed at the school A. However, the inflow amount of black carbon at school B was not greatly influenced by the height of the noise barrier. The inflow amount of black carbon at the schools could be changed not only by the height of the noise barrier, but also by the shape, height and position of the noise barrier and the school building.

The bending exercises of radial tire is one of the most important structural properties of the sidewall relating to ride and road noise of automobiles. The frequency band analysis is more useful for analyzing tire road noise due to property change of tread and sidewall. In this paper, the vertical stiffness and lateral stiffness of tire which have a various tread and sidewall is measured and the road noise is measured about same road condition. Furthermore, we investigated the effect on the structure of the tire tread and sidewall for the sound pressure level.

PURPOSES : A study on the efforts to minimize the road traffic noise has been underway. An attempt has been made to measure the noise level using a noise map; however, the attempt is limited to certain areas only. In general, a noise barrier is employed to prevent road traffic noise; however, unplanned noise barriers developed without considering the surrounding environment, including excessively high walls, cause problems such as infringement on prospect right. Noise ceiling at daytime in Korea is 68 dB(A), which is relatively higher than in other countries. METHODS: The noise barrier used mainly for road noise reduction was analyzed to estimate the optimal height. Related variables such as road width, the height of the upper part, distance to the building, and angle (for instance, 30。). RESULTS : A formula to calculate the optical height of the noise barrier, considering the road environment (i.e., parameters such as road width and distance to building), was developed in this study in an attempt to mitigate the noise generated from the road. CONCLUSIONS : The formula to calculate the noise barrier is expected to lead to cost saving, accurate installation of barriers, and protection of the right of prospect.

Among many potential problems associated with automobiles, the problem regarded as most sensitive and important to the customers is the automobile’s quietness. In particular, because the trend toward the high-performance automobiles is increasing, the quietness should be considered reflecting the increasing demand of the customers for the comfort of automobile ride. Road noise is the low-frequency range in the region of 20Hz to 350Hz, generated when the tires are making contacts with the rough road surface while the automobile is running, in which the noises are resonating within the passenger compartment or with the automobile suspension. In this research, among the factors related to the road noise, the influencing factors associated with the suspension and the tire design were investigated. In particular, among the tire design factors, the structure and the rubber material were investigated as the influencing factors, and for the investigative purpose, experimental tires were manufactured and road noise evaluations were conducted thorough actual feeling tests. Then the test results and correlations were analyzed using the 6-Sigma statistical method. Results from this study shows that, among the tire design factors, the apex is the most influencing factor, in which the height of the apex is the key. The influential factors were found out to be apex height, belt angle, and tread hardness, in that order, and when the suspension is of a same kind, the tendency of the road noise was found to be similar.

PURPOSES: The purpose of this study is to study the noise reducing effect of Micro Surfacing by comparing general asphalt, longitudinal tining and Slurry Seal. METHODS: This study measures vehicles’noise of each section by the NCPX method that can measure noise between the road surface and the tire at the field. Total sound pressure and sound pressure level by the 1/3 octave band frequency are calculated through the field data of each section. Total sound pressure level is compared by ANOVA test statistically. After ANOVA test, post-hoc test is conducted to know mean difference of surface type by Tukey. RESULTS : As the result of CPB analysis to confirm sound pressure levels by frequency, it was shown that sound pressure levels by frequency are totally similar except for those of frequency bands between 100Hz and 500Hz. The result of ANOVA test and post-hoc test, it was shown that sections of surface type have a difference. The result of Micro Surfacing was lower 2~5dB(A) than other surface type. CONCLUSIONS: It is found that the noise reduction performance of Micro Surfacing was better than other surface type.

PURPOSES: The purpose of this study is about noise which is generated from roads and is consist of irregular frequency variation from low frequency to various band. The existing methods of noise reduction are sound barrier that uses insulation material and absorbing material or have applied passive technology of noise reduction by devices. The total frequency band is needed to apply active noise control. METHODS: In this study applies to the field of road traffic environment, signal processing controller and various analog signal input/output, the amplifier module is based on parallel-core embedded processor designed. DSP performs the control algorithm of the road traffic noise. Noise sources in the open space performance of evaluation were applied. In this study, controller of active signal processor was designed based on the module of audio input/output and main controller of embedded process. The controller of active signal processor operates noise reduction algorithm and performance tests of noise reduction in inside and outside environment were executed. RESULTS : The signal processing controller with OMAP-L137 parallel-core processors as the center, DSP processors in the active control operations dealt with quickly. To maximize the operation speed of an object and ARM processor is external function keys and display for functions and evaluating the performance management system was designed for the purpose of the interface. Therefore the reduction of road traffic noise has established an electronic controller-based noise reduction. CONCLUSIONS : It is shown that noise reduction is effective in the case of pour tonal sound and complex tonal sound below 500Hz by appling to Fx-LMS.

Generally, the traffic noise occurring on roads has emerged as an important factor that harms the residential environment. Because of the noise, residents living near roads have been causing civil complaints. Therefore, it is required to evaluate road traffic noise during the whole procedures of building an apartment, ranging from design to construction. And if an evaluated noise exceeds regulation standards, some measures to prevent the noise, such as installation of soundproof walls, and other kinds of plans should be prepared. In this point, this work measured road traffic noise in a site of housing land development, investigated its characteristics, and used a simulation program to predict outdoor noise on the basis of the data about traffic effect evaluation, design drawing, and the data about site measurement. Based on the prediction, it also predicted indoor noise. It is judged that this research will serve as an important material to establish soundproof measures on the basis of prediction of traffic noise in building an apartment.

PURPOSES: The purpose of this study is to research the influence of road traffic noise by road slope through the analysis of the field road traffic noise and determine consideration of road slope in the case of appling active noise cancellation. METHODS: This study measures vehicle's noise by the NCPX method at the three field sections such as uphill, downhill, and flatland. Total sound pressure and sound pressure level by the 1/3 octave band frequency are calculated through the raw field data. Total sound pressure level is compared by ANOVA test and T test statistically. The results obtained are compared in accordance with the road slope and the progress of the uphill section. RESULTS : The noise characteristic of early, medium, and last parts of uphill was found to be consistent when the vehicle was travelling uphill section. The result of statistical test, it was shown that total sound pressures are not different each other. According to the comparison by the geometry, sound pressure of the uphill section was higher than those of the flatland and downhill section in high frequency band. By the result of statistical test, total sound pressure are different according to geometry in the case of high vehicle speed. In the comparison result by road slope, each sound pressure level was found to be consistent in total frequency. However, total sound pressure proportionally increased according to road slope. CONCLUSIONS: It is found that the effect of road slope on noise generation was little in this experimental sites.

PURPOSES: The purpose of study is to understand the characteristic of driving noise from the front and rear tire for effective active noise cancellation application. METHODS : As literature review, noise measurement methods were reviewed. Noise measurement conducted at three kind of section by road slope using CPX(Close Proximity Method). Noise data was compared by total sound pressure level and 1/3 octave band frequency sound pressure level. Also, each section was compared by T-test using SPSS. RESULTS : In the case of the uphill section, it was shown that the sound pressure level of the front tire at Sugwang-Ri and Sinchon-RI sections was higher than that of the rear tire in low and high frequency band. In the case of high slope section of Sangsaek-Ri, the sound pressure level of the front tire was higher than that of the rear tire in high frequency. Also, in the case of the downhill section, it was shown that the sound pressure level of the front tire at Sugwang-Ri and Sinchon-RI sections was higher than that of the rear tire in low frequency band. However, the sound pressure levels of both the front and rear tires were approximately the same in the high slope section of Sangsaek-Ri. The result of T-test showed that total sound pressures of the front and rear tires were not different from each other in the case of high slope and high speed. CONCLUSIONS: Road slope was not an important variable for effective active noise cancellation.

PURPOSES : The purpose of this study is to eliminate the noise of the vehicle after measuring the friction noise obtained from the NCPX (Noble Close ProXimity) method. The pure friction noise between the tire and road pavement could be determined from filtering the compositeness of sound and the influence of the vehicle noise. METHODS: The noise magnitude could be determined by analyzing the sound pressure level (SPL) and sound power level (PWL) along with the noise frequency of a FFT (Fast Fourier Transform) analysis as well as CPB (Constant Percentage Bandwidth) analysis. RESULTS: When the test for measuring the friction noise originated somewhere between tire and road pavement is performed with NCPX method, it must be fulfilled by attaching the surface microphone near the tire. In this condition, the surface microphone can measure the friction noise occurred at between tire and pavement, the chassis noise from the engine and power transfer units, the fluctuating aerodynamic noise, and the turbulence noise directly affected to the surface microphone. By using the NCPX method, the noise occurred at the vehicle must be eliminated for measuring the friction noise between tire and pavement from the traffic noise. CONCLUSIONS: The vehicle's testing engine noise depends on the vehicle and road types. The effect of vehicle's engine noise is less than the friction noise occurred at between tire and pavement at less than 1% effect.