The strengthening of environmental regulations has raised interest in alternative energy and electric car. Secondary batteries are such energy storage device, and in this study, a secondary batteries production equipment parts will be manufactured. To this end, molds were designed and manufactured using numerical analysis. The reliability of analysis is to be confirmed through tensile tests and X-ray tests of products cast with manufactured molds. As the results of the casting method design parts was obtained as the average ultimate tensile strength of 178.23N/mm2, 173.85N/mm2 was recorded and good test results were achieved. It is considered that aluminum alloy research and heat treatment technology development should be carried out in the future.

In order to prepare anode materials for high power lithium ion secondary batteries, carbon composites were fabricated with a mixture of petroleum pitch and coke (PC) and a mixture of petroleum pitch, coke, and natural graphite (PCNG). Although natural graphite has a good reversible capacity, it has disadvantages of a sharp decrease in capacity during high rate charging and potential plateaus. This may cause difficulties in perceiving the capacity variations as a function of electrical potential. The coke anodes have advantages without potential plateaus and a high rate capability, but they have a low reversible capacity. With PC anode composites, the petroleum pitch/cokes mixture at 1:4 with heat treatment at 1000 oC (PC14-1000C) showed relatively high electrochemical properties. With PC-NG anode composites, the proper graphite contents were determined at 10~30 wt.%. The composites with a given content of natural graphite and remaining content of various petroleum pitch/cokes mixtures at 1:4~4:1 mass ratios were heated at 800~1200 oC. By increasing the content of petroleum pitch, reversible capacity increased, but a high rate capability decreased. For a given composition of carbonaceous composite, the discharge rate capability improved but the reversible capacity decreased with an increase in heat treatment temperature. The carbonaceous composites fabricated with a mixture of 30 wt.% natural graphite and 70 wt.% petroleum pitch/cokes mixture at 1:4 mass ratio and heat treated at 1000 oC showed relatively high electrochemical properties, of which the reversible capacity, initial efficiency, discharge rate capability (retention of discharge capacity in 10 C/0.2 C), and charge capacity at 5 C were 330 mAh/g, 79 %, 80 %, and 60 mAh/g, respectively.

It is difficult to make an accurate estimate of the economic value and effects on societal economy of Nano-technologies. This research measures an economic value of Nano-technologies quantitatively and analyzes its influences on societal economy. This paper chooses some major industries as analysis targets and adapts the DEFRA comparative methodology model which has been developed in the UK and recommended by OECD. For this reason, some industries which are in range of economic value assessment were investigated and related data were collected. Also, the economic value and societal influences of Nano-technologies were calculated, through the procedure of the model. In addition, this study conducts a questionnaire to experts for the validity of measurement results and procedures. This paper suggests a guideline for economic value and effects on societal economy of Nano-technologies assessments through quantitative Defra comparative methodologies.

Cathode materials and their precursors are prepared with transition metal solutions recycled from the thewaste lithium-ion batteries containing NCM (nickel-cobalt-manganese) cathodes by a H2 and C-reduction process. Therecycled transition metal sulfate solutions are used in a co-precipitation process in a CSTR reactor to obtain the tran-sition metal hydroxide. The NCM cathode materials (Ni:Mn:Co=5:3:2) are prepared from the transition metal hydroxideby calcining with lithium carbonate. X-ray diffraction and scanning electron microscopy analyses show that the cathodematerial has a layered structure and particle size of about 10 µm. The cathode materials also exhibited a capacity ofabout 160 mAh/g with a retention rate of 93~96% after 100 cycles.

Li metal is accepted as a good counter electrode for electrochemical impedance spectroscopy (EIS) as the active material in Li-ion and Li-ion polymer batteries. We examined the existence of signal noise from a Li-metal counter quantitatively as a preliminary study. We suggest an electrochemical cell with one switchable electrode to obtain the exact impedance signal of active materials. To verify the effectiveness of the switchable electrode, EIS measurements of the solid electrolyte interphase (SEI) before severe Li+ intercalation to SFG6 graphite (at 〉 ca. 0.25 V vs. Li/Li+) were taken. As a result, the EIS spectra without the signal of Li metal were obtained and analyzed successfully for the following parameters i) Li+ conduction in the electrolyte, ii) the geometric resistance and constant phase element of the electrode (insensitive to the voltage), iii) the interfacial behavior of the SEI related to the Li+ transfer and residence throughout the near-surface (sensitive to voltage), and iv) the term reflecting the differential limiting capacitance of Li+ in the graphite lattice.

The various expanded graphites (EGs) was prepared and applied as anode material for high power Li-ion secondary battery (LIB). By changing the processing conditions of EG, a series of EG with different structure were produced, showing the changed electrochemical properties. The charge-discharge test showed that the initial reversible capacity of EG anodes prepared at the suitable conditions was over 400 mAh/g and the charge capacity at 5 C-rate was 83.2 mAh/g. These values demonstrated the much improved electrochemical properties as compared with those for the graphite anode of 360 mAh/g and 19.4 mAh/g, respectively, showing the possibility of EG anode materials for high power LIB.

This study investigated the dependence of the various sputtering conditions (Ar pressure: 2~10 mTorr, Power: 50~150 W) and thickness (50~1200 nm) of Si thin film on the electrochemical properties, microstructural properties and the capacity fading of a Si thin film anode. A Si layer and a Ti buffer layer were deposited on Copper foil by RF-magnetron sputtering. At 10 mTorr, the 50 W sample showed the best capacity of 3323 mAh/g, while the 100 W sample showed the best capacity retention of 91.7%, also at 10 mTorr. The initial capacities and capacity retention in the samples apart from the 50W sample at 10 mTorr were enhanced as the Ar pressure and power increased. This was considered to be related to the change of the microstructure and the surface morphology by various sputtering conditions. In addition, thinner Si film anodes showed better cycling performance. This phenomenon is caused by the structural stress and peeling off of the Si layer by the high volume change of Si during the charge/discharge process.

신뢰성 평가 시험은 종종 성능 평가에 장기간의 시간이 요구되며, 전체 생산비용까지 증가시키는 문제점을 안고 있다. 스트레스를 이용한 가속수명시험은 제품의 신뢰성 고장과 밀접한 관련이 있는 고장 메커니즘의 촉진을 통해 고장에 이르는 기간을 단축함으로써 신뢰성 평가의 효율성을 도모할 수 있다. 본 연구에서는 이러한 스트레스 가속 시험에 빈도가속(Usage-Rate Acceleration) 또는 판정가속(Tightening Critical-Values) 등을

고분자 분리막 기술은 리튬이온전지나 리튬폴리머전지와 같은 리튬이차전지의 성능을 좌우할 정도로 중요한 요소기술이다. 본 논문에서는 지금까지 개발되어 사용되고 있는 다양한 고분자 분리막의 특징 및 기술동향에 대하여 기술하고, 보다 적합한 분리막의 요건을 만족시키기 위한 고분자물질의 판단기준을, 특히 안정성 측면에서 살펴보고자 한다. 또한 실제 리튬이온전지용 분리막을 제조하기 위한 제조공정을 통해 고분자재질의 특징과 관련한 적용성의 여부를 판단코자 하며, 제조된 분리막에 대한 실용화 가능성을 판단하기 위한 분리막의 물리적 요구치 및 측정법에 대하여 기술코자 한다.

Lithium intercalated carbon (LIC) are basically employed as an anode for currently commercialized lithium secondary batteries. However, there are still strong interests in modifying carbon surface of active materials of the anode because the amount of irreversible capacity, charge-discharge capacity and high rate capability are largely determined by the surface conditions of the carbon. In this study, the carbonaceous materials were coated with tin oxide and copper by fluidized-bed chemical vapor deposition (CVD) method and their coating effects on electrochemical characteristics were investigated. The electrode which coated with tin oxides gave the higher capacity than that of raw material. Their capacity decreased with the progress of cycling possibly due to severe volume changes. However, the cyclability was improved by coating with copper on the surface of the tin oxides coated carbonaceous materials, which plays an important role as an inactive matrix buffering volume changes. An impedance on passivation film was decreased as tin oxides contents and it resulted in the higher capacity.