For the regeneration of diesel particulate filters (DPF) using non-thermal plasma (NTP), both cost-effectiveness and regeneration efficiency should be raised. This study compared and contrasted the physicochemical characteristics of carbon black and engine particulate matter (PM). After carbon black was put into the DPF, an experimental setup for the oxidation of PM using NTP was created. The findings showed that carbon black and PM samples had comparable oxidation traits, micronanostructures, and C/O elemental ratios. O3, the main active species in NTP, was susceptible to heat breakdown, and the rate of decomposition of O3 increases with increasing temperature. The removal effectiveness of carbon black first improved and subsequently declined with an increase in the NTP injection flow rate during offline DPF regeneration using NTP at room temperature. A relatively high carbon black removal efficiency of 85.1% was achieved at an NTP injection flow rate of 30 L/min.

The shell & tube-type heat exchanger has been frequently used because it shows simple structure, easy manufacturing and wide operation conditions among many heat exchangers. This study aims to investigate the characteristics for thermal flow of coolant and the possibility of damage for tube equipped with shell due to thermal stress. For these purposes, The thermal flow of coolant in tube was simulated using ANSYS-CFX program and thus the behaviors of coolant were evaluated with standard k-ε turbulence model. As the results, as the flow rate of coolant in tube was increased, the mean relative pressure was also increased with quadratic curve, however, as the surface temperature of tube was increased, mean temperature difference was linearly increased. Finally it showed that the damage of tube could be predicted, that is, which tube was the most weak due to thermal stress.

Given the domestic situation, all nuclear power plants are located at the seaside, where interim storage sites are also likely to be located and maritime transportation is considered inevitable. Currently, Korea does not have an independently developed maritime transportation risk assessment code, and no research has been conducted to evaluate the release rate of radioactive waste from a submerged transportation cask in the sea. Therefore, secure technology is necessary to assess the impact of immersion accidents and establish a regulatory framework to assess, mitigate, and prevent maritime transportation accidents causing serious radiological consequences. The flow rate through a gap in a containment boundary should be calculated to determine the accurate release rate of radionuclides. The fluid flow through the micro-scale gap can be evaluated by combining the flow inside and outside the transportation cask. In this study, detailed computational fluid dynamic and simplified models are constructed to evaluate the internal flow in a transportation cask and to capture the flow and heat transfer around the transportation cask in the sea, respectively. In the future, fluid flow through the gap will be evaluated by coupling the models developed in this study.

As the saturation rate of temporary storage facilities for spent nuclear fuel increases, regulatory demands such as interim storage and permanent disposal of spent nuclear fuel are expected to begin in earnest. Considering the domestic situation where all nuclear power plants are located on the waterfront site, the interim storage site is also likely to be located on the waterfront site, and maritime transportation is one of the essential management stages. Currently, there are no independently developed maritime transportation risk assessment code in Korea, and no research has been conducted to evaluate the release of radioactive waste due to the sinking of transport container. Therefore, it is necessary to secure technology to properly reflect the domestic maritime transportation environment and to assess the impact of the sinking accident and to carry out safety regulations. To accurately calculate the releaser rate of radionuclides contained in a cask with breached containment boundary, the flow rate through the gap generated in the containment boundary should be calculated. The fluid flow through this gap which is probably in micro scale in most situations should be evaluated combining the fluid flow inside and outside the cask. In this study, a detailed computational fluid dynamics model to evaluate the internal fluid flow in the cask and a simplified model to capture the fluid flow and the heat transfer around the cask in the sea are constructed. The results for the large scale model are compared with the analytic formula for verification of heat transfer coefficient and they showed good agreements. The heat transfer coefficient thus found can be used in the detailed model to provide more realistic data than those obtained from assumed heat transfer coefficient around the surface of the cask. In the future, fluid flow through the gap between the lid and the body of the cask will be evaluated coupling the models developed in this work.

In thermal cutting process, gas flow injected from the nozzle has a significant effect on the cutting materials. The gas flow is difficult to observe gases are transparent, therefore, in this study, Schlieren method was adopted to visualize the gas flow inside the kerf. The kerf shape was inserted between two slices of transparent glass in order to imitate the real cutting environment. In order to get the flow characteristics, a high speed camera was equipped and the image processing was applied to compare the before and after injection images. As a result, the method for visualizing gas flow was successfully developed and also expected to be applied to the analysis of purging gas in various welding environments.

Small-sized heater is usually used to make the hot water in resting place, factory, household affairs and so on. One of methods to obtain hot water in short time is known as using instantaneous electric water heater. In this study, numerical analysis for small-sized hot water heater with straight double tube-type was tried to achieve the basic design data. This study aims to investigate the characteristics of thermal flow, for instance, such as pressure difference, outlet mean temperature and velocity, due to clearance. As the clearance is decreased, outlet mean temperature and pressure difference(Pmax.-Pmin.) are increased. Therefore appropriate relations between area of heat source and pressure difference should be set up. Further small-sized hot water heater in this study must be equipped with electric device capable of heating over 90℃.

IMO에서는 선박으로부터 온실가스 감축을 위해 선박의 에너지효율 증진에 관한 논의를 진행하고 있다. 현재, 선박으로부터 발생되는 폐열을 이용한 ORC 발전 시스템을 적용함으로써 선박으로부터 높은 에너지 변환 효율을 기대할 수 있다. 이 기술은 물보다 더 낮은 온도 범위에서 증발하는 프레온 또는 탄화수소 계통의 유기 매체를 작동 유체로 사용한다. 이를 통해 상대적으로 낮은 저온에서 증기 (기체)를 생성 및 동력을 발생시킬 수 있다. 본 연구에서는 유기 랭킨 사이클인 ORC 발전 시스템에서 냉매와 폐열 사이 열·유동해석 (Analysis of Heat flow)을 3D 시뮬레이션 기법을 이용하여 구조물의 내·외부에 흐르는 유체가 온도 변화, 속도 변화, 압력 변화 및 질량 변화를 통해서 구조물에 어떤 영향을 미치는지를 분석하고자 하며, 동 연구는 이 기법을 이용하여 ORC 발전 시스템에서 냉매와 선박 주기 관의 배기가스로부터 일어나는 열교환기의 열전달을 해석하였다.

이 연구의 목적은 강남 선정릉지역에서 전산유체역학모델(CFD)을 사용하여 도시지역의 흐름 및 열 환경 모의를 검증하는 것이고, CFD 모델의 모의결과와 선정릉 지역의 관측 자료와 비교하는 것이다. CFD 모델은 국립기상과학원과 서울대가 공동으로 연구 개발된 모델이다. CFD_NIMR_SNU 모델은 기상청 현업 모델인 국지예보모델(LDAPS)의 바람성분과 온도성분을 초기 및 경계조건으로 적용되었고 수목효과와 지표 온도를 고려하여 2015년 8월 4일에서 6일까지 강남 선정릉 지역을 대상으로 수치실험을 진행하였다. 선정릉지역에서 수목효과 적용 전후의 풍속을 비교하였을 때 평균 제곱근 오차(RMSE)는 각각 1.06, 0.62 m s−1로 나타났고 수목효과 적용으로 풍속 모의정확도가 향상되었다. 기온은 LDAPS 과소 모의하는 경향을 나타내고 CFD_NIMR_SNU 모델에 의해 향상된 것을 확인하였다. CFD_NIMR_SNU 모델을 이용하여 복잡한 도시지역의 흐름과 열 환경을 자세하고 정밀한 분석이 가능하며, 도시 환경 및 계획에 대한 정보를 제공 할 수 있을 것이다.

본 논문에서는 과도한 계산용량이 필요한 초음속 비행체의 비정상 열응답 해석을 수행하기 위한 준-비정상해석 기법을 소개한다. 준-비정상해석 기법은 연성 연계 기법과 복합 열전달 해석기법을 통합한 방법으로 계산시간 단축시키면서 동시에 정확도를 향상시키기 위해 고안되었다. 또한 준-비정상해석 시, 해석 구간을 분할하기 위한 기준시간을 결정하는 알고리즘을 고안하여 준-비정상해석 기법의 정확도를 향상시키고자 하였다. 본 논문에서는 준-비정상해석 기법을 평가하기 위하여 가상의 비행 시나리오에서 열응답 해석을 수행하였으며, 비정상 해석 결과와 비교 검증을 수행하였다. 무딘 물체의 표면 온도 및 정체점의 온도를 통해 각각의 기법의 차이를 도출하였다. 비정상 해석을 통해 도출한 정체점의 온도와 준-비정상 해석을 통해 도출한 정체점의 온도 차이는 11.4% 이내로 높은 정확도를 확보함과 동시에 28배에 가까운 계산시간을 단축시켜 해석 기법의 효율성과 정확성을 확보하였다.

A 2D axisymmetric numerical analysis was performed to study the characteristics of charge process inside solar thermal storage tank. The porosity and heat transfer coefficient of filler material as well as inlet velocity of heat transfer fluid are selected as simulation parameters. The porosity is varied as 0.2, 0.5, and 0.8 to account for the effect of filler granule geometry. Two levels of the heat transfer coefficient is adopted to assess the heat transfer between heat transfer fluid and filler material. The inlet velocity is varied as 0.00278, 0.0278, and 0.278m/s. As both of the porosity and the heat transfer coefficient increase, the discrepancy of the temperature distributions between the filler and heat transfer fluid decreases. As the inlet velocity increases, the penetration depth of the heat transfer fluid increases proportionally.

A 2D axisymmetric numerical analysis was performed to study the characteristics of charge process inside solar thermal storage tank. The interfacial area density and inertial resistance of filler material are selected as simulation parameters. The interfacial area density is varied as 800, 2000, and 4000 1/m. The inertial resistance is varied as 1, 3, and 5 1/m. When the interfacial area density increases from 800 to 4000 1/m, the discrepancy of the temperature distributions between the filler and heat transfer fluid decreases. As inertial resistance increases from 1 to 5, both of the temperature and fluid flow pattern changes considerably.

This study is about comparison of thermal and flow characteristics on the wind & radiant heat shield with STS mesh type screen for offshore plant. Numerical analysis was conducted to find transmission coefficient in the mesh and then analyse the flow characteristics about wind & radiant heat shield. The experiment method of solar radiation has been used as thermal radiation source to get the performance of radiant heat shield measurement. The sensor radiation device has been used to measure the reduction of solar radiation with various size of cells and at a distance of 0.5m and 1m from the cold face of the wind & radiant heat shield. The present study show reduction in radiation heat flux as various distance from the cold face of the radiant heat shield. Experimental results are presented for different type of mesh and distance of measurement.

원자력을 이용한 황-요오드 수소생산 공정 중 황산용액을 이송하는 기존의 시스템과 달리 새로운 황산 이송장치는 벨로우즈 박스 내에서 벨로우즈 외측으로 고온 부식성 액체인 황산이 흐르고, 벨로우즈 내측으로는 냉각수가 흐르는 상태에서 주기 운동을 통해 황산용액이 펌핑 되도록 구성된다. 200 ℃ 이상의 고온 부식성 액체인 황산용액을 정량으로 이송할 수 있도록 장치의 주요부품인 벨로우즈 주변의 열해석을 통해 온도분포를 확인하여, 테프론 재질의 벨로우즈의 내식성 및 내열성을 파악하고, 장치의 안전하고 효율적인 운용을 위한 기초자료를 취득하고자 하였으며, 냉각수 입구직경 3 ㎝, 질량유량이 3.9199 ㎏/s로 고정한 경우 벨로우즈의 길이에 관계없이 테프론 변형온도 이하임을 알 수 있었다.

강관이 매설되어 있는 폐쇄형 시스템에서 동결된 화강토의 온도분포에 관한 수치해석 및 실험적 연구가 수행되었다. 실험을 통해 측정된 부동수분량의 온도상관식을 제시하였으며, Lachenbruch의 열전도율 식을 사용하여 열전도율 측정값을 비교분석하였다. 원형 단면 강관이 매설된 모형토조의 동결챔버를 제작하여 동결토의 온도를 측정하고 유한요소 수치해석을 수행하여 실험 결과와 비교하였다. 수치해석시 동결된 화강토의 잠열효과가 고려되었다.

2충의 BPSG를 사용하는 서브마이크론 CMOS DRAM에 있어 전기적 특성에 관한 BPSG flow온도의 영향을 비교하였다. BPSG flow온도를 850˚C/850˚C, 850˚C/900˚C, 900˚C/900˚C의 3가지 다른 조합을 적용하여 문턱전압, 파괴전압, Isolation전압과 더불어 면저항과 접촉 저항을 조사하였다. 900˚C/900˚C flow의 경우 NMOS에서 문턱전압은 0.8μm 미만의 채널길이에서 급격히 감소하나 PMOS 경우는 차이가 없었다. NMOS와 PMOS의 파괴전압은 각각 0.7μm와 0.8μm 이하에서 급격히 감소하였다. 그러나 850˚C/850˚C flow의 경우에는 NMOS와 PMOS모두 문턱전압과 파괴전압은 채널길이 0.7μm까지 감소하지 않았다. Isolation전압은 BPSG flow온도 감소에 따라 증가하였다. 면저항과 접촉 저항은 BPSG flow온도가 900˚C에서 850˚C로 감소됨에 따라 급격히 증가되었다. 이와 같은 결과는 열처리 온도에 따라 dopant의 확산과 활성화에 관련 있는 것으로 생각된다. 접촉 저항 증가에 대한 개선 방법에 대하여 고찰하였다.