중앙분리대 콘크리트 방호울타리(Concrete Median Barriers, CMB)는 마주 달리는 차량과의 정면충 돌을 예방할 뿐만 아니라 탑승자의 상해 및 차량의 파손까지 최소화하는 중요한 안전시설 중 하나이 다. 현재 국내의 CMB는 설계속도에 따라 등급이 정해지고, 이에 맞는 성능 평가를 실시하게 된다. 현 재 국내의 특수구간을 제외한 저속구간 및 일반구간(60~80km/hr)에서는 SB4등급 이하의 CMB가 사 용되고 있으며, 고속구간(100km/h 이상 도로)에서는 SB5등급 이상의 CMB가 사용된다. 그중 고속국 도에 시공되는 SB5등급 이상의 CMB에 대한 연구는 지속해서 수행되는 반면 일반국도에 대한 CMB 연구는 비교적 부족한 실정이다. 따라서 본 연구에서는 일반국도에 시공되는 SB4등급의 효율적인 단 면을 찾기 위한 해석적 연구가 수행되었다. 단면 형상은 1, 2차 충돌에 큰 영향을 미치는 단면의 높이 와 최하단부의 곡률 반경이 고려되었다. 유한요소 해석에 사용된 차량은 미국 교통부(U.S Department of Transportation)에서 제공한 16톤 트럭을 국내 차량과 비슷한 형태로 개선한 차량이었다. 해석 결과 로, 트럭의 충돌 후 단면 형상에 따라 발생한 트럭의 거동, 콘크리트 비산량, 소성변형이 비교되었다.

This study reports an analytical investigation on the development of SB4-grade separated concrete median barriers. The proposed barrier sections comprise three designs, with heights of 810, 1000, and 1270 mm and upper widths of 90, 120, and 120 mm, respectively. Before conducting collision analyses on the proposed sections, the considered collision analysis model was validated using real collision test results; the model was found to accurately predict the real collision test results. The proposed cross-sections were modeled to perform collision analysis according to SB4-grade collision conditions. Results indicated that increasing the cross-section height increased the damaged area and decreased the strength, while the occupant protection performance remained mostly unaffected. Furthermore, the proposed cross-sections met the strength and occupant protection performance criteria specified in domestic guidelines, suggesting their suitability as a separated concrete median barrier for bridges.

PURPOSES : The objective of this study is to determine the characteristics of nitrogen oxide (NOx) concentration in an exclusive median bus lane station. The hourly variations of NOx concentration and the effect of traffic volume on NOx concentration were analyzed using NOx measurement data and the number of vehicles at the station. METHODS : Data were collected using the chemiluminescence method for NOx concentration. Atmospheric information and traffic volume of buses were collected from the Korea Meteorological Administration and Bus Information System, respectively. RESULTS : As a result, the NO2 concentration in the test section was found to have a strong correlation with those in the atmospheric measurement station located near the test-bed. In addition, the average NOx concentrations in the test section were significantly higher than those of the other monitoring stations due to bus emissions. The average NOx concentration in the exit section was higher than that in the entry section owing to the vehicle’s frequent stops and fuel consumption due to acceleration. During the measurement period, the average NOx concentration was measured as approximately 33 % higher in the exit section than in the entry section. In addition, the NOx concentration at the bus station was found to increase as the bus dwell time increased, rather than the number of bus passages. CONCLUSIONS : This study provides clear characteristics of the NOx correlations with traffic information in an exclusive median bus lane station. It was shown that the NOx concentration at the bus station increased as the number of passes and bus dwell time increased. According to the coefficient of determination, the dwell time is more closely correlated to the NOx concentration at the bus station than the number of bus passes, indicating that it is a better parameter for predicting NOx concentration at bus stations.

PURPOSES : This paper is to deliver an engineering design guide currently unavailable that highway engineers can refer to when they need to determine the safe distance between the starting point of the underground highway in a metropolitan area and the access points of the adjacent highway. METHODS : The distance between two different highway points should be sufficiently far to support the number of lane changes that drivers may take comfortably at the cruising speed in critical traffic conditions. RESULTS : The proper distance for the selected case study is calculated to be 160 and 200 m at the cruising speeds of 40 km/h and 50 km/h, respectively, without significant increase in potential conflicts estimated by the combination of the VISSIM and SSAM analysis. CONCLUSIONS : The proposed design method can be referred in urban metropolitan areas where no specific design guide is yet available, and it would prevent the unnecessary increase in construction costs and encourage private-public partnership highway businesses.

PURPOSES: This study analyzes feasibility for application white pavement markings in the roadways with median barrier. METHODS : By reviewing numerous relevant laws, standards, and operational cases, the white pavement markings' excellence was demonstrated. Driver’s behavior was analyzed through a virtual driving experiment using driving simulator and field tests. RESULTS: First, white pavement markings are superior to yellow pavement markings in terms of visibility, economics, and safety. Second, as a result of virtual driving experiment, the color of line in the roadway with median barrier didn’t affect the driver’s behavior such as the average vehicle speed, the distance bias in the lane and the separation distance from the centerline. Third, field test demonstrated that the driver tended to recognize the median barrier as an obstacle. In addition, the central driving ratio in the lane was increased due to improving the visibility of line at night in case of the white pavement markings. CONCLUSIONS : The application of white pavement markings in the roadways with median barrier can enhance traffic safety by improving the visibility of line at night.

The Golden Gate Bridge, known as one of the most beautiful bridges in the world, serves 110,000 vehicles per day, connecting San Francisco to inland as a segment of Highway 101 in California. The average peak hour volume over 6,500 vehicles per hour exceeds the traffic capacity of three lanes on each direction. Due to unique function of the bridge as a gateway of San Francisco, the peak directions in the morning and afternoon were explicitly distinguished. Recurrent traffic delay on the peak direction deteriorated level of service during the commute periods and caused user’s inconvenience and traffic accidents. The workers previously used to move plastic delineators to change lane configuration (4-2, 3-3, and 2-4) in several times a day. Neither did it provide prevention nor physical protection from the head-on collision on the bridge section. In January 2015, the Golden Gate Bridge was completely closed for two days to install the moveable median barrier (MMB) system, Road Zipper®, for more effective and safer variable lane management than the previous operation. One-meter section with 30.48 cm wide of highly reinforced concrete barriers are linked to form a continuous barrier wall and the machine lifts and passes the barriers through a conveyor system at a seeds up to 16 km/h. The MMB enables to quickly reverse lane configuration without traffic closure, providing more lanes to the peak direction as well as eliminating head-on collision on the bridge deck by presence of a physical structure. The traffic monitoring study result shows the significant improvement of average speed during peak hours and the regional traffic accident records shows improvement of safety after implementing the MMB on the Golden Gate Bridge. According to the traffic accident records, 13 injuries occurred in five accidents of vehicle collision in two-directions from 2007 to 2014 but no two-way accident has been reported since the operation of the Road Zipper® began. Furthermore, the MMB would be effectively implemented on construction work zones, managed lanes, variable lane management and other traffic operation to improve traffic safety and maximize utilization of roadway facilities.

국내 고속도로 콘크리트 중앙분리대는 SB5-B(270kJ)의 충돌등급에 저항하도록 설계되어 있다. 그러나 최근 대형 화물차 량의 충돌사고가 지속적으로 증가하는 경향을 보이고 있어 SB6(420kJ) 등급으로의 상향이 필요하다. 충돌등급 상향을 위한 새로운 중앙분리대 단면을 제시하기 위해서는 실제 충돌시험을 수행하여 기준 통과여부를 결정하며, 충돌시험 수행을 위한 적정 단면을 제시하기 위해서는 충돌해석을 통해 선정한다. 이러한 충돌해석의 정확도 향상을 위해서는 차량 모델, 콘크리트 단면 열화상태, 콘크리트 피복 두께 등 다양한 변수에 대한 정확한 변수 선정이 필요하다. 따라서 본 연구에서는 공차 중량, 단면 열화, 콘크리트 피복 두께에 대한 변수연구를 수행하여 충돌저항성능 저감을 확인하였다. 전체 중량뿐만 아닌 공차 중 량에 따라 중앙분리대의 충돌저항성능에 차이가 있는 것으로 확인되었으며, 10cm 이하의 콘크리트 피복 두께에서는 충돌저 항성능이 민감하게 증가 또는 감소한다. 단면 열화가 발생할 경우 중앙분리대의 충돌저항성능의 감소가 발생하여 열화정도 에 따른 보수 및 보강이 이루어져야 하는 것으로 판단된다. 따라서 콘크리트 구조물과 차량의 충돌해석을 수행할 경우 트럭 의 공차중량 비율, 콘크리트의 피복두께 및 열화에 대한 영향이 상세하게 고려될 필요가 있음을 확인하였다.

PURPOSES : The purpose of this paper is to develop a methodology to estimate level of service of arterial including Exclusive Median Bus Lanes. METHODS : On 6 Exclusive Median Bus Lanes routes in Seoul, bus travel time and number of bus-stop per km were investigated. Also whether or not passing lane exists at bus-stop was checked. Based on the data from sites, bus travel time was estimated according to length of segment, number of bus-stop per km and whether or not passing lane exists at bus-stop. RESULTS : A bus travel time table was developed according to length of segment, number of bus-stop per km and whether or not passing lane exists at bus-stop. After bus travel speed and passenger car travel speed is estimated based on each travel time table and length of segment, two speeds are combined with weighted average speed using traffic volume of each lane group. Then weighted average speed is a measure of effectiveness of arterial including Exclusive Median Bus Lanes. CONCLUSIONS : It can be concluded that the proposed methodology can estimate level of service of arterial including Exclusive Median Bus Lanes considering the operation characteristics of Exclusive Median Bus Lanes.

PURPOSES: The purpose of this study is to develop an effectiveness analysis method of exclusive median bus lanes, which is necessary in order to improve operation efficiency of exclusive median bus lanes. METHODS : The operation characteristics of "signalized intersection including exclusive median bus lanes" and "normal signalized intersection" were investigated and the existing capacity analysis method was also reviewed to analyze the effectiveness of exclusive median bus lanes. Delay reduction of passengers using exclusive median bus lanes which can be considered as the benefit of exclusive median bus lanes and the number of people in buses were included in the proposed effectiveness analysis method. RESULTS : It was found that the proposed method expresses properly the effectiveness of exclusive median bus lanes through performing sensitivity analysis and analyzing with the real data of the number of people in buses and passenger cars. It was also found that the proposed method demonstrates the effectiveness that measure of effectiveness of signalized intersections is changed to "sec/person". CONCLUSIONS : It was concluded that the method is a proper effectiveness analysis method because it can reflect the benefit of passengers in buses.

PURPOSES: By conducting the landscape survey that considered landscape factors of the Guide Coating in the Median Barrier that applied of the various level by simulating of the Guide Coating in the Median Barrier on the expressway, they showed the quantitative standard of landscape preference factors that the Guide Coating gives. METHODS: The shape of the Structural Equation Modeling used AMOS program and made a shape that is made of landscape preference for the Guide Coating in the Median Barrier on the expressway a dependent variable. RESULTS: Result in this, they showed that functionality and emotionalism are the factors that affect the landscape preference. CONCLUSIONS: In the main study, not only showing the Guide Coating in the Median Barrier on the expressway landscape valuation but also embodying the Structural Equation Modeling(SEM) of each group, knowing the Guide Coating and unknowing the Guide Coating. By embodying this, they could study that the drivers' quantitative standard is different when the Guide Coating become first applied and being changed after.

PURPOSES : In this study, the effects of when median exclusive bus lanes were applied to Daejeon trunk road (Wolpyeng crossway~Seodaejeon crossway, 6.3km) and (Daeduck Bridge 4~Kyeryong 4, 2.6km) by Microscopic Simulation VISSIM (5.0) was studied. The median exclusive bus lanes are one of the measures of transportation system manage techniques that can especially improve the efficiency of public transportation facilities. METHODS : According to the analysis of VISSIM on the Gyerong mainroad and Daedeok mainroad, when the median exclusive bus lanes were applied unlike when the roadside bus-only lanes were applied, the average travel speed of vehicles decreased but the average delay time and travel time increased. This arised from the changes in the geometric structure of the road which occurred the reduction of vehicle lane in the center of the road. RESULTS : In the case of bus, on the other hand, the average travel speed increased but the average delay time and travel time decreased. This is because the problems such as illegal parking and stopping, secondary road in out vehicle, and conflict of intersection right turn that roadside bus-only lanes occurred was solved. CONCLUSIONS : Although the introduction of median exclusive bus lanes will have a negative effect on general traffic flow due to the aggravation of travel, decrease of passenger car usage will lead to decrease of traffic volume. Therefore, smooth vehicle travel is expected.

현재 서울시는 대중교통 활성화 정책에 따라 버스전용차로제도를 실시하고 있다. 과거 가로변버스전용차로 설치를 시작으로 현재에는 중앙버스전용차로 설치구간도 증가하고 있다. 본 연구의 목적은 이 중앙버스전용차로와 가로변버스전용차로에서 버스사고에 영향을 미치는 요인을 분석하는데 있다. 분석방법으로 교통사고가 확률적으로 극히 드물게 일어난다는 점을 생각하여 포아송 회귀모형과 음이항 회귀모형을 선택하였으며, 과산포 존재여부에 따라 음이항 회귀모형으로 최종모형을 정립하였다. 중앙버스전용차로구간은 버스노선수, 중앙차로 진출입 유형수, 중앙차로 정지선 후퇴유무, 중앙차로 정지선과 횡단보도 이격거리, 교통량, 가변차로 정류장 정차노선수 6개의 변수에서 버스사고에 유의한 영향을 미치는 것으로 나타났다. 가로변버스전용 차로구간은 우회전 버스노선수, 상습 불법주정차 유무, 보행신호시간, 토지이용형태 4개의 변수에서 버스사고에 유의한 영향을 미치는 것으로 나타났다.

정부는 교통사고 사상자를 절반으로 줄이기 위하여 생활권 보행자 안전 확보를 위한 안전대책을 선정하여 추진 중에 있다. 주요 추진내용을 살펴보면 중앙선 침범 및 무단횡단 예방을 위해 도심형 중앙분리대 설치기준 마련이 포함되어 있어 기준마련을 위한 연구가 매우 시급한 실정이다. 이에 본 연구에서는 보행자 및 중앙선 침범 교통사고 분석, 도심형 중앙분리대에 대한 형식 및 성능기준, 최소 횡단구성 연구를 통한 설치 기준에 관한 연구를 수행하였다. 그 결과 도시부 차량 불법유턴, 보행자 무단횡단 사고를 줄이고자 시선유도봉을 개조한 도심형 중앙분리대는 차량용 방호울타리의 강한 방호기능을 가질 수 없기 때문에 차량과의 충돌 후 파손되어 부재이탈이 발생하게 되면 2차 사고 등을 유발하게 되어 교통안전에 부(-)의 효과를 가져 올 수 있는 것으로 분석되었다. 이에 주행안전성 측면을 고려해 볼 때 도심형 중앙분리대를 설치할 경우 중앙분리대 폭 1.0m 이상을 확보해야만 시설물 파손이나 차로 이탈을 방지할 수 있는 것으로 분석되었다. 단, 부득이 도로 폭이 좁아 용지확보가 곤란한 경우 0.5m 이상 노면표시만 설치한 경우에 한해 도심형 중앙분리대의 설치를 할 수 있다. 또한 현재 중앙선 위에 시선유도봉이나 도심형 중앙분리대를 설치하는 것은 운전자 실수에 의한 중앙선 침범을 유발할 가능성이 높고 이로 인해 시설물 파손의 가능성이 높아 중앙선 위에는 표지병 이외의 시설물 설치를 금하는 것이 바람직하다.

Six sigma has been the most influential management innovation tool in order to achieve the customer’s satisfaction and keep the competition in the age of limitless competition. The success in six sigma is to find the correct CTQ (Critical to Quality). QFD

p-median 문제는 복잡한 공간문제, 특히 시설물 입지선정에 있어 최적 지점과 해를 탐색하는데 적용되어 왔다. 본 논문은 이러한 p-median 문제해결에 적용되는 알고리즘을 이용하여 또 다른 공간최적화 문제중의 하나인 구역설정문제(zone design problem)의 적용방안에 대하여 논의하고자 한다. 구역설정문제는 인구센서스 구역 계획, 학군설정, 및 선거구 획정과 같은 공간단위와 관련된 다양한 현실 문제와 연관되어 있는 지리적 탐색 문제이다. 본 논문에서는 센서스 구역 설정문제와 연관하여 p-median 문제해결에 적용되어 온 대표적인 알고리즘과 Cooper 탐색 휴리스틱을 제안하고자 한다. 이를 위해 센서스 집계구(census output areas)를 대상으로 가상적인 구역들을 설정하여 설정과정에서의 p-median 알고리즘의 탐색 결과와 향후 구역설정문제에 대한 적용 가능성에 대해 논의하고자 한다.