For improvement of wear resistance property of atmospheric thermal plasma sprayed molybdenum (Mo) coating, diamond deposition on the atmospheric plasma sprayed molybdenum coating by the combustion flame chemical vapor deposition (CFCVD) has been operated. In this study, to diminish the thermal damage of the substrate during operation, a thermal insulator was equipped between substrate and water-cooled substrate holder. Consequently, diamond particles could be created on the Mo coating without fracture and peeling off. From these results, it was found that this process had a high potential in order to improve wear resistance of thermal sprayed coating.

TZM alloy having elongated coarse-grain structure was developed by three-step internal nitriding treatment at 1423 to 1873 K in and subsequent recrystallization treatment at 2173 K in vacuum. Some specimens were subjected to re-nitriding treatment at 1873 K for 16 h. After the recrystallization treatment, aspect ratio (L/W) of grains for rolling direction was about 50 at the maximum. Yield stress obtained at 1773 K after re-nitriding treatment was about 6 times as large as that of recrystallized specimen. Re-nitriding was very effective in the improvement in strength of TZM alloy having elongated coarse-grain structure.

Compositional dependence of corrosion behavior of rapidly solidified Mg-rich Mg-Zn-Y alloys in NaCl aqueous solution has been investigated. Mg-Zn-Y ternary alloys containing small amounts of Zn exhibited low corrosion rate, although the (at. %) binary alloy showed severe corrosion with violet evolution of hydrogen. The alloy with highest corrosion-resistance was , its corrosion rate was about 1 mm year-1 in 0.17 M (1.0 wt. %) NaCl solution. alloy exhibited passive region in anodic polarization curves when immersed in NaCl solution. Rapidly solidification and small amount of Zn addition may bring about an increase in electrochemical homogeneity of Mg-Zn-Y alloys, resulting in enhancement of corrosion resistance.

Electric scroll-compressor drives are commonly used for e.g. home appliance cooling units. The recent development of hybrid cars with internal combustion engine in combination with electrical propulsion requires new solutions to be able to cool the passenger compartment of cars at stand-still. Both application areas demand efficient motor drives to reach good economy and efficient use of limited battery power as well as competitive volume/weight for a given output. The BLDC motor is a controllable and efficient solution. A major part of the motor is the soft-magnetic core. The powder based Somaloy® material shows high resistivity and induction as the result of engineered iron particles with in-organic coating. The unique features of compacted Somaloy® components can be utilized to enhance the shape and total volume of the BLDC motor with at least maintained efficiency compared to the use of traditional laminated steel sheet cores. A careful design of the Somaloy® components can also simplify assembly and positively influence the coil configuration. This study shows a comparison between a typical laminated BLDC motor and a redesigned, Somaloy® based version adapted for a scroll-compressor application.

This study was conducted to detect the apoptosis incidence in blastocysts and to compare the abundance of Bax, Bcl2L1, VEGF and FGFR2 in in vitro fertilized (IVF), parthenogenetic (PAT) and nuclear transfer (NT) embryos. Oocytes matured for 40 hr were enucleated and reconstructed with confluenced fetal fibroblasts (FFs) derived from a ～45 day fetus. Reconstructed eggs were then fused with 2 DC pulses (2.0 kV/cm, 30 μsec) and cultured with 7.5 μg/ml cytochalasin B for 3 hr. Parthenotes (PAT) were produced with the same electric strength and culture for NT eggs. The embryos were cultured in NCSU-23 medium at 39℃, 5% CO2, 5% O2 in air. In 3 runs, set of 10 embryos at the 4-cell to blastocyst stages were used to extract total RNA for analyzing the gene expression patterns of pro-apoptotic (Bax), anti-apoptotic (Bcl2L1), vasculogenesis (VEGF), implantation (FGFR2III) using real-time quantitative PCR. Cleavage and blastocyst rates were significantly higher (P<0.05) in IVF and PAT (79.3±8.5 and 25.5±6.1, and 85.0±6.4 and 38.6±5.5, respectively) than NT counterparts (65.1±5.2 and 15.6±3.0, respectively). Significantly higher (P<0.05) total cells were observed in IVF controls and PAT (34.7±5.8 and 38.1±4.1) than NT embryos (24.8±3.2). Apoptosis index was significantly lower (P<0.05) in IVF than NT embryos. The Relative abundances (RA) of Bax and VEGF were significantly higher (P<0.05) at blastocyst stage in NT than IVF control. The RA of Bcl2L1 and FGFR2III were significantly higher (P<0.05) at blastocyst stage in IVF than NT. The present study observed the abnormal gene expressions in NT embryos at various developmental stages, suggesting certain clues to find out the cause of the low efficiency of NT to term.

The influence of doping on the structural and morphological properties of the phosphor system, obtained ultrasonically via Spray Pyrolysis from common gadolinium and europium nitrate solutions, was studied. The particle morphology, crystalline and chemical structure were studied by XRD, SEM and EDS. TEM was applied in order to identify the structure and growth of "primary nanoparticles" and determine the presence of domains locally affected by "Moires Frames" and "Crystallite Size". The SADP allows determining the presence of a polycrystalline material with two phases in the "as-prepared" samples, and only an Ia3 phase along the thermal treatment.

The present study investigates the behavior of the sintering and hardness of stainless steel samples reinforced with NbC and TaC. Matrixes of pure stainless steel were compacted with addition of up to 3% wt NbC or TaC in a cylindrical die of steel at 700 MPa and sintered in an electrical resistance furnace under argon atmosphere. The sintered samples were characterized by density and hardness measurement, optical microscopy and scanning electron microscopy (SEM). The preliminary results show that the size and distribution of carbides influence in the sintering and hardness of the sintered samples.

A high nitrogen PM tool steel has shown to have an excellent galling resistance due to the introduction of a high amount of a low friction phase predominantly consisting of VN. Tool making and heat treatment are according to standard procedures. An increase of tool life of more than two times compared to ordinary tool steels is found. Furthermore, the new low friction tool steel shows a potential for sintered parts with higher densities through the applica bility of increased compaction pressure or minimized lubricant amount.

By means of magnetic pulsed compaction and sintering of weakly aggregated alumina based nanopowders the jet forming nozzle samples for the hydroabrasive cutting were fabricated. The ceramics was obtained from pure alumina, as well as from alumina, doped by , MgO and AlMg. It was shown that the samples sintered from AlMg doped powder have the best mechanical properties and structural characteristics: relative density , channel microhardness. - 18-20 GPa, channel surface roughness , average crystallite size .

Ru-C nano-composite films were prepared by MOCVD, and their microstructures and their electrode properties for oxygen gas sensors were investigated. Deposited films contained Ru particles of 5-20 nm in diameter dispersed in amorphous C matrix. The AC conductivities associating to the interface charge transfer between Ru-C composite electrode and YSZ electrolyte were 100-1000 times higher than that of conventional paste-Pt electrodes. The emf values of the oxygen gas concentration cell constructed from the nano-composite electrodes and YSZ electrolyte showed the Nernstian theoretical values at low temperatures around 500 K. The response time of the concentration cell was 900 s at 500 K.

The sintering behavior of titanium-titanium nitride nanocomposite powders has been studied by dilatometry. Titanium. titanium nitride nanocomposite powders were produced by the reactive milling of micron sized titanium powder in nitrogen atmosphere. The Ti-TiN nanocomposite powders milled for various durations along with the initial micron sized Ti powders were then sintered in the temperature range of by a constant rate of heating . The linear shrinkage, shrinkage rate, activation energy for sintering and microstructure has been studied and discussed as a function of milling time.

The fabrication of complex-shaped parts out of Co-Cr-Mo alloy and 316L stainless steel by three-dimensional printing (3DP) was studied using two grades of each alloy with average particle size of 20 and , respectively. To produce sound specimens, the proper 3DP processing parameters were determined. The sintering behavior of the powders was characterized by dilatometric analysis and by batch sintering in argon atmosphere at for 2h. The 3DP process has successfully produced complex-shaped biomedical parts with total porosity of 12-25% and homogenous pore structure, which could be suitable for tissue growth into the pores.

The preparation of composite powders for plasma spraying by an in-house designed mechanofusion process is investigated. Results show that dry particle coating depends on the chemical and mechanical properties of powders. In metal/oxide and metal/oxide/carbide powder mixtures, fine ceramic particles coat the surface of the metallic coarser particles. A nearly rounded shape of the final composite particles is induced by the mechanical energy input with no formation of new phases. However with the carbide/metal powdered system, only an intimate mixture of components is achieved. It is suggested that the coating mechanism is governed by agglomeration and rolling phenomena.