최근 화석자원의 고갈과 대기오염의 피해를 저감하기 위해 자전거의 이용을 적극적으로 장려하고 있으며 이를 위해 자전거도로 건설이 활발히 이루어지고 있다. 하지만 현재 사용 중인 자전거도로 포장은 이용 하중에 비해 높은 성능과 시공비용을 지니고 있어 효율적인 건설을 위해 경제적인 도로포장형식이 필요하다. 롤러 전압 콘크리트 포장은 시멘트 경화 반응과 다짐으로 인한 골재 맞물림에 따른 높은 구조적 성능을 확보할 수 있다. 또한 시공이 간단하고 건설비가 적어서 자전거도로에 적용하기 위한 우수한 조건을 갖추고 있다. 그러나 롤러 전압 콘크리트 포장의 불량한 표면 미관과 제설제 피해에 대한 취약성은 자전거도로 건설에서 문제로 작용하고 있다. 따라서 이러한 단점을 극복하기 위해 표면 미관의 개선과 환경하중에 대한 피해를 저감 할 수 있을 것으로 예상되는 코팅공법을 이용하였으며 이에 대한 효과를 검증하기 위해 롤러 전압 콘크리트 포장의 코팅에 따른 성능을 검토하였다.

It has been considered that fishing areas for shrimp beam trawl have been in ruin because Korean local governments have permitted trawling into the areas limited by the fisheries local regulations from 1994. Physical and biological effects of the trawling were investigated in the study. Physical effects were investigated by optical methods such as trawling tracking by side scan sonar and comparing the gear both before and after trawling. Biological aspects were investigated by grab sampling of benthic animals, concentration of trace metals in sediment and a flux evaluation of NH4+, PO4-, and SiO2 by coring. The fishing activity had physical impacts on the seabed but these recovered naturally in less than fourty days naturally, which increased the benthic biodiversity, increases the trace metal concentration of and nutrient flux into the seawater, especially phosphate and silicate. This method and these results can help in further studies looking for disturbances by fishing.

To prepare weather-resistant silicone/acrylic resin coatings for an architectural purpose, tetrapolymers were synthesized by a radical polymerization. 3-Methacryloxypropyltrimethoxysilane (MPTS) as a silicone monomer and n-butyl acrylate, methyl methacrylate, and n-butyl methacrylate as acrylic monomers were used. The compositions of monomers were adjusted to fix the glass transition temperature of acrylic polymer for 20℃. The composition of MPTS in the synthesized polymer were varied from 10 wt% to 30 wt%. On the basis of synthesized resin amber paints were prepared and their physical properties and effects for weatherability were examined. The presence of MPTS in silicone/acrylic resins generally resulted in low molecular weight and broad molecular weight distribution, and also lowered the viscosity of the copolymers. The coated films prepared from these resins showed good and balanced properties in general. Adhesion to the substrate was outstanding in particular. Weatherability tests were carried out in three different types such as outdoor exposure, QUV, and SWO. The test results showed that the silicone/acrylic resins containing 30 wt% of MPTS had weather-resistant properties.

The high-solid coatings were prepared by blending the synthesized acrylic resin in the previous paper, and hexamethylene diisocyanate-trimer and curing it at room temperature. The characterization of the films of the prepared coatings was performed. The 60˚ specular gloss, impact resistance, cross-hatch adhesion, and heat resistance of the films proved to be good, and the pencil hardness, drying time, and pot-life proved to be slightly poor. From a viscoelastic measurement using a rigid-body pendulum, curing was accelerated with the Tg value.

Solvent-free low foaming scouring agents (LFSC) were prepared by blending of 2-ethylhexylaminoethyl sulfate (2-EHAS), POE(10) octadecylbenzyl- ammonium chloride (POBAC) and Sedlan FF-200 (FF-200). As the results of several tests, 2-EHAS/POBAC/FF-200/water (8g/12g/20g/60g) mixture (LFSC-5) showed good cleaning power, penetrating ability and stability to alkali, and gave less problem in water pollution. The foaming power of LFSC-5 measured by Ross and Miles method was 8mm foam height immediately after foaming, and that measured by Ross and Clark method was less than 300mm foam height at 30℃, and 18mm at 80℃. As a result, LFSC-5 proved a good low foaming scouring agent for fiber.

The aim of this study is to synthesis basic resins for the preparation of PU flame-retardant coatings that contain phosphorus and chlorine. After synthesizing intermediates of tetramethylene bis(orthophophate) (TMBO) and neohexanediol trichlorobenzoate (TBA-adduct), the condensation polymerization was performed with the intermediates, 1,4-butanediol, and adipic acid to obtain four-component copolymers. In the condensation polymerization, the content of phosphorus was fixed to be 2%, and the content of trichlorobenzoic acid (TBA) that provides chlorine component was varied to be 10, 20, and 30wt%, and we designated the prepared modified polyesters containing chlorine and phosphorus as TTBA-10C, TTBA-20C and TTBA-30C. Average molecular weight and polydispersity index of the prepared TTBAs decreased with increasing TBA content because of the increase in the number of hydroxyl groups that retards reaction. We found that the thermal stability of the prepared TTBAs increased with chlorine content at high temperatures.

In the previous study, three kinds of monomers and the functional monomer, acetoacetoxyethyl methacrylate (AAEM), which could improve the film property and cross-linkage, were polymerzied into acrylic resin copolymers (HSA-98-20, HSA-98-0, HSA-98+20) containing 80% solid content. In this study, the high-solid coatings(HSA-98-20C, HSA-98-0C, HSA-98+20C) were prepared by the curing reaction between acrylic resins containing 80% solid content and isocyanate at room temperature. Various properties were examined for the film coated with the prepared high-solid coatings. The introduction of AAEM in the coatings enhanced the abrasion resistance and solvent resistance of coatings, which indicated the possible use of high-solid coatings for top-coating materials of automobile. The curing times measured by viscoelastic measurement were 350, 264, and 212 min for HSA-98-20C, HSA-98-0C, and HSA-98+20C, respectively. This shows that the curing times become shorter with increasing Tg values.

Acrylic resins (HSCs : EA/EMA/2-HEMA/CLA) which contain 70% solid content were synthesized by the copolymerization of monomers (2-hydroxyethyl methacrylate, ethyl acrylate, and ethyl methacrylate) and functional monomer (caprolactone acrylate : CLA) which improves the crosslinking density and physical properties of films. The physical properties of the prepared acrylic resins (HSCs) containing CLA, are as follows : viscosity 245~515 cps ; Mn 2670~2840 ; and conversions, 83~91%, respectively. From the correlation of Tg values, viscosities, and Mn of the HSCs, it was found that viscosity and Mn increased with Tg value.

염분에 대한 두줄망둑의 내성범위를 파악하기 위한 일환으로 이들의 생존, 성장 및 산소소비에 미치는 염분의 영향을 40일간 사육실험을 통하여 검토하였다. 두줄망둑의 생존율은 염분 10.1‰ 이상에서 90%이상을 나타냈으나, 염분 3.4‰ 이하에서는 유의한 감소를 나타냈고, 담수에서는 40일째 32.5%의 생존율을 보였다. 체장과 체중의 증가 및 성장률은 13.4∼33.6%o의 염분 범위에서 유사

The high-solid coatings were prepared by blending the synthesized acrylic resin in the previous paper and hexamethylene diisocyanate-trimer and curing it at room temperature. The characterization of the films of the prepared coatings was performed. The impact resistance, 60℃ specular gloss, cross-hatch adhension, and heat resistance of the films proved to be good, and the pencil hardness and drying time proved to be slightly poor. Especially, there was a remarkable improvement in the heat resistance. This improvement may stem from the regular arrangement of ethyl groups introduced into the acrylic resin. From a viscoelastic measurement using a rigid-body pendulum, curing was accelerated with the Tg value. With the increase in Tg, log damp value was lowered and dynamic viscoelasic Tg of a cured film was increased.

연안지역의 환경오염 및 양식용수의 이용과정에 파생될 수 있는 구리의 오염에 따른 넙치의 생존, 대사율, 사료효율 및 성장율에 미치는 구리의 영향을 검토하였다. 4개의 아치사구리 농도(50, 80, 180, 320 μg L-1)에서 6주동안 실험하였다. 실험기간 동안 넙치는 대조구에서는 실험종료시 까지 사망개체가 전혀 나타나지 않아 100%의 생존율을 나타내었다. 구리 노출농도 180 μg L-

Environmental friendly acrylics/urea high-solid paints (BEHCU) were prepared through the curing reaction of acrylics resin(BEHC) containing 70wt% of solids content and butylated urea curing agent. BEHC was synthesized by addition copolymerization of caprolactone acrylate(CLA), 2-hydroxypropyl methacrylate(2-HPMA), ethyl methacrylate, and n-butyl acrylate. The addition polymerization of these monomers, especially including flexible CLA monomer and 2-HPMA monomer with OH funtional group, under appropriate reaction conditions resulted in polymers with controlled glass transition temperature(Tg) and crosslinking density. The molecular weight(Mw) of these polymers(BEHCs) was 2940~3240 and polydispersity (Mw/Mn) was in the range of 1.61~1.72. The viscosity and the molecular weight of these acrylic resins increased with increasing Tg. The coated films were prepared using curing reaction between BEHC resin and butylated urea curing agent at 100℃ for 30 minutes. Our experimental resulted showed that enhancement of the coating properties such as adhesion, flexibility, impact resistance, water resistance, and abrasion resistance could be expected through introducing CLA component in acrylic resin for the high-solid content acrylics/urea coatings.

To prepare an environmental friendly high-solid coatings an acrylic resin containing 80% of solid content was synthesized by addition polymerization of caprolactone acrylate, n-butyl acrylate, ethyl methacrylate, and 2-hydroxyethyl methacrylate. The conversion was 78~93% and the prepared resin's physical properties are as follows: viscosity, 212~3424cps: Mn 1740~2400. There was a trend that viscosity and molecular weight of the resin increased with Tg, but no direct proportionality was observed.

The objectives of this study is to investigate the optimum reaction conditions and to identify the product formula in the synthesis of a silicone/acrylic resin that curing in moisture at room temperature. By the addition polymerization of monomers, n-butyl acrylate, methyl methacrylate, n-butyl methacrylate, and 3-methacryloxypropyltrimethoxysilane. a quarter polymer was obtained. Among various initiators investigated in this study, 2.2'-azobisisobutyronitrille was found to be the most suitable initiator. The optimum reaction conditions found in this study are 70 wt% of initial solvent amount, 120 minutes of dropping time, 3 times of initiator addition, 82~105℃ of reaction temperature, and 8 hrs of reaction time. Also, number average molecular weight of 11700~33100 and molecular weight distribution of 1.81~3.44 were obtained.

Durable softening water repellents such as PODCW, PDDCW, and PEDCW were prepared by blending cationized polymers, fatty carbamide, waxes, and emulsifiers. The cationized polymers included poly (octadecyl methacrylate-co-2-diethylaminoethyl methacrylate) [PODC], poly (n-dodecyl methacrylate-co-2-diethylaminoethyl methacrylate) [PDDC]and poly (2-ethylhexyl methacrylate-co-2-diethylaminoethyl methacrylate) [PEDC]. After the PET fabrics were treated with these water repellents, water repellency, softness, and durability of the PET fabrics were examined by various methods : water repellency by the hydrostatic pressure and the contact angle methods, softness by crease recovery and tearing strength, and durability by washability, respectively. Rating of water repellency of PET fabrics treated with PODCW was 80+, but those treated with PDDCW and PEDCW were not high enough to be used in industry.

Spin finish(SF) for nylon filament was prepared. The influence on the properties of filament obtained by treating the prepared spin finish in this study(SF-2) and foreign-made spin finish(Spinnar N-100) was compared. SF-2 prepared by blending of spindle oil 70g, paraffin wax 10g, glyceryl mono-oleate 5g, POE(6) nonylphenyl ether 4g, POE(10) nonylphenyl ether 4g, POE(10) octylphenyl ether 2g, POE(14) mono-oleate 4g and water 1g was excellent in its characteristics. Some of the properties of Nylon filament treated with SF-2 were better than those treated with Spinnar N-100. Also, optimal physical conditions of nylon filament according to the number of revolution of oil roller were obtained at conditions of 5rpm of number of revolution oil roller, 1.25% of SF-2 oil pick up, and denier 69D.

The 2-packaged polyurethane coatings were synthesized, blending pheylmodified polyesters(of which synthetic methods were reported in the previous paper), Desmodur L-75(polyisocyanate wide1y used for coatings), wetting-dispersing agent, white pigment. etc. A variety of coating properties were tested for the coating treatment polyurethane coationgs. Compared with conventional 2-packaged polyure-thane coating, abrasion resistance and lightness index difference of the ones synthesized in the present work were somewhat decreased, but the coating properties such as hardness, gloss specular, cross hatch adhesion. etc. were improved. Especially, resistance against chemical reagents and salt were strikingly improved. In addition. the coationgs had short drying time and long pot-life. This shows that the coationgs are appropriate for rapid drying coatings.