The fishery compensation by marine spatial planning such as routeing of ships and offshore wind farms is required objective data on whether fishing vessels are engaged in a target area. There has still been no research that calculated the number of fishing operation days scientifically. This study proposes a novel method for calculating the number of fishing operation days using the fishing trajectory data when investigating fishery compensation in marine spatial planning areas. It was calculated by multiplying the average reporting interval of trajectory data, the number of collected data, the status weighting factor, and the weighting factor for fishery compensation according to the location of each fishing vessel. In particular, the number of fishing operation days for the compensation of driftnet fishery was considered the daily average number of large vessels from the port and the fishery loss hours for avoiding collisions with them. The target area for applying the proposed method is the routeing area of ships of Jeju outer port. The yearly average fishing operation days were calculated from three years of data from 2017 to 2019. As a result of the study, the yearly average fishing operation days for the compensation of each fishing village fraternity varied from 0.0 to 39.0 days. The proposed method can be used for fishery compensation as an objective indicator in various marine spatial planning areas.

1970년대 초반 독일 사회로 이주한 많은 한국인들은 체류기간을 엄격히 지켜야 하는 손님노동자 (Gastarbeiter)였다. 그들의 자녀들은 독일사회에서 이중문화를 지닌 소수집단으로서 교포 2세로 자랐다. 그들은 집에서는 한국 문화, 집 밖에서는 독일 문화와 마주해야 했으며, 이로 인해 많은 이들이 정체성 혼돈을 겪어왔다. 이 점에 착안하여 본 연구는 재독 교포 2세 청소년들의 정체성 형성에 관한 연구를 진행하였다. 이를 위해 근거이론에 기반한 분석을 진행하였다. 더불어 분석의 깊이를 더하기 위하여 미드 (G. H. Mead)의 상징적 상호작용주의와 파크(R. E. Park)의 주변인 이론을 분석에 접목하였다. 특히, 신문 자료를 활용한 2차 분석 을 주로 시도하였다. 분석 결과, 재독 2세들은 한국인으로서의 정체성을 자랑스럽게 여기고 있었고, 한국계 네트워크 구축 및 한국문화 교육에 적극적으로 참여하고 있는 것으로 나타났다. 또한 1세대 부모들의 한국문화를 유지하려고 노력하고 있는 것으로 나타났다. 이렇게 볼 때 재독 2세들의 네트워킹을 활성화할 수 있는 다양하고 지속적인 관심과 지원이 필요할 것으로 보인다.

본고의 목적은 선교적 실행을 위하여 장소의 개념과 종류, 그 변화에 대하여 이해하고자 하는 것이다. 이 시대의 상황은 탈장소화라 고 할 수 있는데 그것은 초기술 사회의 소통 기술의 획기적인 발달로 인하여 비장소, 다장소, 가장소, 그리고 무장소 등으로 나타나고 있다. 예전의 공간 중심의 세계관에서 최근 장소 중심의 세계관으로 이동하고 있는데 이 탈장소화 시대에서의 장소의 의미와 그 중요성을 살펴보는 것은 중요하다. 장소는 공간과 구별되어 이해되어야 하는데 장소는 역사적인 의미가 있는 특정 공간이다. 특히 기독교적 혹은 선교적 공동체를 위하여 탈장소화 시대에서의 선교와 장소와의 관계, 장소의 변화와 선교적 장소에 대하여 논하는 것이 필요하다. 선교적으로 모든 공간을 담보하기 위하여 우리는 특정 장소를 기반으로 하지 않으면 안 된다는 역설을 발견한다. 그리고 ‘특정 장소를 기반으로 한 탈장소화’ 는 시대적 거대 상황에 대한 전략적인 상황화와 함께, 이를 통하여 선교적 장소들을 오히려 창의적으로 재생산하여 미래 기독교 공동체의 구체성과 현실성을 상실하지 않아야 한다.

본 논문에서는 우리나라의 중저준위 방폐물 처분을 위한 사일로 형식 지하동굴의 유한요소해석을 수행하였다. 사일로의 벽체부분 은 지름 25m의 원형구조이고, 높이는 35m이다. 사일로의 천장부분은 지름 30m의 돔 형식이고, 높이 17.4m의 규모이다. 사일로는 해 수면으로부터 –80m에서 –130m에 위치하고 있다. 중저준위 방폐물 처분 1단계 시설로 6개의 사일로가 건설되어 운영되고 있으나, 본 연구에서는 1개의 사일로에 대해서 고려하였다. SMAP-3D 프로그램을 사용하여 2차원 축대칭 유한요소모델과 3차원 유한요소모델 을 생성하였다. Generalized Hoek and Brown Model이 수치해석에 적용되었다. 다양한 측압계수(수평방향 현장응력과 수직방향 현장 응력의 비)의 변화에 따른 사일로 형식 지하동굴의 유한요소해석을 수행하였으며, 수치해석결과 및 분석결과가 제시되었다.

본 연구는 지역별로 수집한 유채 균핵병 균주에 대해 등록 된 3종의 약제를 사용하여 저항성 검정을 실시하였고, 저항성 발생 가능성이 있는 약제의 작용 기작과 관련한 유전자를 분석하여 변이 유무를 확인하였다. 1. Carbendazim-diethofencarb 약제배지의 경우, 0.1 ppm 농도에서 균사 생장 억제율은 13.3~41.9% 범위로 나타났으며, 1 ppm 이상의 농도에서는 모든 균주에서 96.1% 억제율을 보여 균주의 저항성이 확인되지 않았다. 2. Fludioxonil 약제배지는 0.1 ppm 농도에서 균사의 생장이 94.2% 이상 억제되었으며, 1 ppm 농도에서부터 100%의 억제 율을 보여 가장 약제 효과가 우수한 것으로 나타나 수집한 모든 균주에서 약제의 감수성을 확인하였다. 3. Boscalid 약제배지는 앞선 2종의 약제에 비해 균주의 균사 생장 억제가 뚜렷하지 않았다. 특히 10 ppm 농도에서 무안 수집 균주는 93.9%, 나주 수집 균주는 79.3%로 지역 간 차이가 있었으며, 1000 ppm의 높은 약제 농도에서도 균사의 생장을 100%까지 억제하지 못해 약제에 대한 균주의 저항성 발생 가능성을 추측하였다. 4. 3종의 시험 약제 농도별 균핵병 균주의 균사 생장을 50% 억제하는 농도(EC50)를 분석한 결과, Fludioxonil, Carbendazim-diethofencarb, Boscalid 약제순이었으며, 그 값은 각각 0.06, 0.16, 0.43 ppm으로 나타났다. 5. 또한, 3종의 시험 약제 농도별 발생한 균주의 균핵 형성 능력은 1 ppm 농도에서 Carbendazim-diethofencarb는 5.6개, Fludioxonil은 0개로 나타난 반면, Boscalid는 최대 11.3개의 균핵이 형성되어 차이를 확인할 수 있었다. 6. Boscalid 약제에 대한 균주의 저항성을 확인하기 위해 해당 약제의 작용 기작인 SDHI와 관련된 유전자 SdhB를 염기 서열 분석하였다. 염기서열 분석 결과 무안 및 부산에서 수집 한 균주의 경우 SdhB 표준 염기서열과 일치하여 감수성이었으나, 나주, 당진, 제주, 영암에서 수집한 균주는 32번째 염기 가 C→T로 치환되어 GCA(Alanine)→GTA(Valine) 점 돌연변이를 확인하였다.

In this study, a nanocrystalline FeNiCrMoMnSiC alloy was fabricated, and its austenite stability, microstructure, and mechanical properties were investigated. A sintered FeNiCrMoMnSiC alloy sample with nanosized crystal was obtained by high-energy ball milling and spark plasma sintering. The sintering behavior was investigated by measuring the displacement according to the temperature of the sintered body. Through microstructural analysis, it was confirmed that a compact sintered body with few pores was produced, and cementite was formed. The stability of the austenite phase in the sintered samples was evaluated by X-ray diffraction analysis and electron backscatter diffraction. Results revealed a measured value of 51.6% and that the alloy had seven times more austenite stability than AISI 4340 wrought steel. The hardness of the sintered alloy was 60.4 HRC, which was up to 2.4 times higher than that of wrought steel.

In this study, a drifting test using a experimental vessel (2,966 tons) in the northern waters of Jeju was carried out for the first time in order to obtain the fundamental data for drift. During the test, it was shown that the average leeway speed and direction by GPS position were 0.362 m/s and 155.54° respectively and the leeway rate for wind speed was 8.80%. The analysis of linear regression modes about leeway speed and direction of the experimental vessel indicated that wind or current (i.e. explanatory variable) had a greater influence upon response variable (e.g. leeway speed or direction) with the speed of the wind and current rather than their directions. On the other hand, the result of multiple regression model analysis was able to predict that the direction was negative, and it was demonstrated that predicted values of leeway speed and direction using an experimental vessel is to be more influential by current than wind while the leeway speed through variance and covariance was positive. In terms of the leeway direction of the experimental vessel, the same result of the leeway speed appeared except for a possibility of the existence of multi-collinearity. Then, it can be interpreted that the explanatory variables were less descriptive in the predicted values of the leeway direction. As a result, the prediction of leeway speed and direction can be demonstrated as following equations. However, many drift tests using actual vessels and various drifting objects will provide reasonable estimations, so that they can help search and rescue fishing gears as well.

Various surface colors are predicted and implemented using the interference color generated by controlling the thickness of nano-level diamond like carbon (DLC) thin film. Samples having thicknesses of up to 385 nm and various interference colors are prepared using a single crystal silicon (100) substrate with changing processing times at low temperature by plasma-enhanced chemical vapor deposition. The thickness, surface roughness, color, phases, and anti-scratch performance under each condition are analyzed using a scanning electron microscope, colorimeter, micro-Raman device, and scratch tester. Coating with the same uniformity as the surface roughness of the substrate is possible over the entire experimental thickness range, and more than five different colors are implemented at this time. The color matched with the color predicted by the model, assuming only the reflection mode of the thin film. All the DLC thin films show constant D/G peak fraction without significant change, and have anti-scratch values of about 19 N. The results indicate the possibility that nano-level DLC thin films with various interference colors can be applied to exterior materials of actual mobile devices.

The effect of sintering conditions on the austenite stability and strain-induced martensitic transformation of nanocrystalline FeCrC alloy is investigated. Nanocrystalline FeCrC alloys are successfully fabricated by spark plasma sintering with an extremely short densification time to obtain the theoretical density value and prevent grain growth. The nanocrystallite size in the sintered alloys contributes to increased austenite stability. The phase fraction of the FeCrC sintered alloy before and after deformation according to the sintering holding time is measured using X-ray diffraction and electron backscatter diffraction analysis. During compressive deformation, the volume fraction of strain-induced martensite resulting from austenite decomposition is increased. The transformation kinetics of the strain-induced martensite is evaluated using an empirical equation considering the austenite stability factor. The hardness of the S0W and S10W samples increase to 62.4-67.5 and 58.9-63.4 HRC before and after deformation. The hardness results confirmed that the mechanical properties are improved owing to the effects of grain refinement and strain-induced martensitic transformation in the nanocrystalline FeCrC alloy.

We fabricate the non-equiatomic high-entropy alloy (NE-HEA) Fe49.5Mn30Co10Cr10C0.5 (at.%) using spark plasma sintering under various sintering conditions. Each elemental pure powder is milled by high-energy ball milling to prepare NE-HEA powder. The microstructure and mechanical properties of the sintered samples are investigated using various methods. We use the X-ray diffraction (XRD) method to investigate the microstructural characteristics. Quantitative phase analysis is performed by direct comparison of the XRD results. A tensile test is used to compare the mechanical properties of small samples. Next, electron backscatter diffraction analysis is performed to analyze the phase fraction, and the results are compared to those of XRD analysis. By combining different sintering durations and temperature conditions, we attempt to identify suitable spark plasma sintering conditions that yield mechanical properties comparable with previously reported values. The samples sintered at 900 and 1000oC with no holding time have a tensile strength of over 1000 MPa.

As interest in vocational competency development projects increases, support is increasing. In this study, in order to study ways to improve participation in vocational competency development training, related factors are selected and the main factors influencing them are derived. The main factors were influencing factors were identified and ways to improve participation rate of vocational competency development were studied. Variables were selected through prior research, and data were collected and analyzed through in-depth group interviews. Based on factor analysis and reliability analysis, as a result of confirming the factors that influence the plan for improving participation in vocational competency development training by applying the backward stage selection (condition) method of logistic regression analysis, the case of respect for minorities in the 7-point Likert scale The closer to 7 was, the higher the probability of being classified as having never participated, and the other factors except minority respect, Likert scale closer to 7 indicates higher probability of bening classified as having never participated, except for the minority respect factor. Therefore, it was confirmed that lowering the scale of the factor of respect for minority, which is job satisfaction, and increasing the factors of individual characteristics such as annual salary and organizational commitment, training system for job satisfaction, and quality assurance have effects on improving participation rates in vocational competency development training.

High-entropy alloys have excellent mechanical properties under extreme environments, rendering them promising candidates for next-generation structural materials. It is desirable to develop non-equiatomic high-entropy alloys that do not require many expensive or heavy elements, contrary to the requirements of typical high-entropy alloys. In this study, a non-equiatomic high-entropy alloy powder Fe49.5Mn30Co10Cr10C0.5 (at.%) is prepared by high energy ball milling and fabricated by spark plasma sintering. By combining different ball milling times and ball-topowder ratios, we attempt to find a proper mechanical alloying condition to achieve improved mechanical properties. The milled powder and sintered specimens are examined using X-ray diffraction to investigate the progress of mechanical alloying and microstructural changes. A miniature tensile specimen after sintering is used to investigate the mechanical properties. Furthermore, quantitative analysis of the microstructure is performed using electron backscatter diffraction.