PURPOSES : The purpose of this study is to verify the influences on the compactibility evaluation of WMA (Warm Mix Asphalt) mixture by laboratory experiments. METHODS : Two types of WMA additives (chemical and wax types) and two types of compactors (marshall and gyratory) are used in laboratory experiments. In addition, two types of WMA processes (wet and dry) are tested to verify the impact of manufacturing process. RESULTS : The laboratory results show that the effects of compaction method on compactibility are different depending on the type of additive. The compaction method has a significant impact on WMA mixture with chemical type additive to extent that it determines whether required criterion is satisfied, but only little on WMA mixture with wax type additive. In the case of wet process for WMA mixture manufacturing, it is hard to assess the air void of HMA mixture made of same asphalt binder used in WMA mixture since the additive has already been added in asphalt binder. And the test results show that air voids of HMA mixture vary within properties of asphalt binder. CONCLUSIONS : Through this study, it is found that compactibility of WMA mixture is affected by the compaction methods depending on the additive types and by the WMA mixture manufacturing process. Therefore, those are recommended to be considered when evaluating compactibility of WMA mixtures.

The study confirmed the "house search report(家宅搜索調書)" containing criminal records during the Japanese colonial period, as well as the production process and the way of expressing the illustrations contained in them. It also explored architectural values through analysis of the location and use of the building. This records the discovery of evidence by searching the residences of those involved in the crime from 1919 to 1922. The illustrations contained in this record were not standardized, so the contents of the article differed depending on the author's background and cultural experience. Nevertheless, this painting reflects the regional characteristics of traditional houses located throughout the Korean Peninsula. It is also evidence that the house was used for cultural, commercial, and industrial purposes, beyond the general assumption that it was used only for residential purposes. The "House Search Report(家宅搜索調書)" provides information on ordinary buildings that existed as the background of everyday life, rather than buildings with a specific purpose or exceptional design. It is evaluated as an important resource for understanding the diverse life and spatial structures of buildings during that time.

This study aimed to assess and determine the optimal model for predicting the full bloom date of ‘Fuji’ apples across South Korea. We evaluated the performance of four distinct models: the Development Rate Model (DVR)1, DVR2, the Chill Days (CD) model, and a sequentially integrated approach that combined the Dynamic model (DM) and the Growing Degree Hours (GDH) model. The full bloom dates and air temperatures were collected over a three-year period from six orchards located in the major apple production regions of South Korea: Pocheon, Hwaseong, Geochang, Cheongsong, Gunwi, and Chungju. Among these models, the one that combined DM for calculating chilling accumulation and the GDH model for estimating heat accumulation in sequence demonstrated the most accurate predictive performance, in contrast to the CD model that exhibited the lowest predictive precision. Furthermore, the DVR1 model exhibited an underestimation error at orchard located in Hwaseong. It projected a faster progression of the full bloom dates than the actual observations. This area is characterized by minimal diurnal temperature ranges, where the daily minimum temperature is high and the daily maximum temperature is relatively low. Therefore, to achieve a comprehensive prediction of the blooming date of ‘Fuji’ apples across South Korea, it is recommended to integrate a DM model for calculating the necessary chilling accumulation to break dormancy with a GDH model for estimating the requisite heat accumulation for flowering after dormancy release. This results in a combined DM+GDH model recognized as the most effective approach. However, further data collection and evaluation from different regions are needed to further refine its accuracy and applicability.

This study was conducted to determine the optimal irrigation starting point by analyzing tree growth, physiological responses, fruit quality, and productivity in peach orchards. Seven-year-old ‘Kawanakajima Hakuto’ peach trees were used in an experimental field (35°49′30.4″N, 127°01′33.2″E) located within the National Institute of Horticultural and Herbal Science located in Wanju-gun, Jeollabuk-do. The irrigation starting point was set with four levels of –20, –40, –60, and –80 kPa from June to September 2022. While there were no significant differences in increase of trunk cross-section area and leaf area among treatments, shoot length and diameter decreased in the –80 kPa and –20 kPa treatments. The photosynthetic rate measured in August was highest for –60 kPa (17.7 μmol·m-2·s-1), followed by –40 kPa (15.6 μmol·m-2·s-1), –20 kPa (14.5 μmol·m-2·s-1) and –80 kPa (14.0 μmol·m-2·s-1). SPAD value measured in May and August was lower in the –80 kPa and –20 kPa treatments than in the –60 kPa and –40 kPa treatments. The harvest date reached three days earlier in the –20 kPa treatment compared to other treatments. The fruit weight was highest in the –60 kPa (379.1 g), followed by –40 kPa (344.0 g), –80 kPa (321.0 g) and –20 kPa (274.9 g). Firmness was the lowest in the –20 kPa treatment. The soluble solid content was highest in the –60 kPa treatment (13.3°Bx).The ratio of marketable fruits was highest in the –60 kPa treatment (50.7%) and lowest in the –80 kPa treatment (23.4%). In conclusion, we suggest that setting the irrigation starting point at –60 kPa could improve the fruit quality and yield in peach orchards.

This study used optical and scanning electron microscopy to analyze the surface oxidation phenomenon that accompanies a γ'-precipitate free zone in a directional solidified CM247LC high temperature creep specimen. Surface oxidation occurs on nickel-based superalloy gas turbine blades due to high temperature during use. Among the superalloy components, Al and Cr are greatly affected by diffusion and movement, and Al is a major component of the surface oxidation products. This out-diffusion of Al was accompanied by γ' (Ni3Al) deficiency in the matrix, and formed a γ'-precipitate free zone at the boundary of the surface oxide layer. Among the components of CM247LC, Cr and Al related to surface oxidation consist of 8 % and 5.6 %, respectively. When Al, the main component of the γ' precipitation phase, diffused out to the surface, a high content of Cr was observed in these PFZs. This is because the PFZ is made of a high Cr γ phase. Surface oxidation of DS CM247LC was observed in high temperature creep specimens, and γ'-rafting occurred due to stress applied to the creep specimens. However, the stress states applied to the grip and gauge length of the creep specimen were different, and accordingly, different γ'-rafting patterns were observed. Such surface oxidation and PFZ and γ'-rafting are shown to affect CM247LC creep lifetime. Mapping the microstructure and composition of major components such as Al and Cr and their role in surface oxidation, revealed in this study, will be utilized in the development of alloys to improve creep life.

Fouling is an inevitable problem in membrane water treatment plant. It can be measured by trans-membrane pressure (TMP) in the constant flux operation, and chemical cleaning is carried out when TMP reaches a critical value. An early fouilng alarm is defined as warning the critical TMP value appearance in advance. The alarming method was developed using one of machine learning algorithms, decision tree, and applied to a ceramic microfiltration (MF) pilot plant. First, the decision tree model that classifies the normal/abnormal state of the filtration cycle of the ceramic MF pilot plant was developed and it was then used to make the early fouling alarm method. The accuracy of the classification model was up to 96.2% and the time for the early warning was when abnormal cycles occurred three times in a row. The early fouling alram can expect reaching a limit TMP in advance (e.g., 15-174 hours). By adopting TMP increasing rate and backwash efficiency as machine learning variables, the model accuracy and the reliability of the early fouling alarm method were increased, respectively.

The production process of ultra-pure water (UPW) involves dozens of unit processes such as reverse osmosis (RO), pretreatments, membrane degasifier, and several ion exchange processes. Recently, continuous electrodeionization (CEDI) has replaced the 2-bed and 3-tower (2B3T) ion exchange process. As a result, the majority of wastewater in UPW production now comes from the RO concentrate. The important of RO in UPW production is to produce high-quality water with a low ion concentration (around 1 mg/L) for CEDI feed water. Minimizing RO concentrate is essential to reduce the wastewater produced in the UPW production process. This can be achieved by maximizing the recovery of the RO system. However, increasing the recovery is limited by the water quality of the RO permeate. To ensure high-quality permeate water, the RO system is designed with a two-pass configuration. The recovery of each pass in the RO system is limited (e.g., < 85%) due to the expected increase in permeate water concentration at higher RO feed water concentrations. Interestingly, tests using 4-inch RO modules with low concentration feed water (≤ 35 mg/L as NaCl) revealed that the permeate concentration remains almost constant regardless of the feed water concentration. This implies that the recovery of the first RO pass can be increased as long as the average feed/concentrate concentration of the second RO pass is less than 35 mg/L. According to this design criterion for the RO system, the recovery of the first and second RO pass, with a feed water concentration of 250 mg/L as NaCl, can be increased up to 94.8% and 96.0%, respectively. Compared to the conventional RO system design (e.g., 70% and 80% for the first and second RO pass) for UPW production, this maximum recovery design reduces the volume of RO feed and concentrate by up to 38.4% and 89.2%, respectively.

The compositions of ethnic groups in Macau vary with time. Prior to the opening of the port, the majority of the residents in Macau were Chinese people, including those living on land and at sea. After the port was opened, with the increase of Portugal businessmen and missionaries, the population was divided into Chinese people and foreigners (so-called ‘Yiren’ or 夷人in Chinese). Chinese people living on land were mainly of Hakka, Fujian, and Cantonese descent. Those living at sea were referred to as ‘Tanka People’ (named ‘Danmin’ or 蜑民in Chinese). They lived on floating boats for their entire lives and were similar to the ‘drifters’ in Japan. Since modern times, many refugees from mainland China and Southeast Asia flooded into Macau due to warfare. The development of industrialization required a larger number of laborers, and some ‘coolies’ entered Macau in legal or illegal ways, making it a multi-ethnic city. However, the Tanka people were not considered a minority ethnic group under the national ethnic policy of 56 ethnic groups since they did not have an exclusive language and shared dialects in different regions. As the ports inhabited by Tanka people gradually restored foreign trade, the boats and stilt houses used by Tanka people were dismantled to expand the infrastructure area of the ports. Many Tanka people began to live on land and marry people on land, leading to the disappearance of the Tanka group in Macau. The fishing boats and stilt houses used by Tanka people have also disappeared, with only a few remaining in areas such as Pearl River Delta and Hong Kong. This paper examines the natural and social environment of Tanka people in Macau from the Ming and Qing dynasties to the Republic of China, as well as the adaptive changes they adopted for the aforementioned environment in terms of living space and architectural type, on the basis of summarizing the historical activities of Tanka people. Finally, this study provides a layout plan and interior structure of the most commonly used boat for Tanka people from the Ming and Qing dynasties to the Republic of China, with the use of CAD and other technical software, along with reference to written historical documentation, and provides a case study for further research on the architectural history of Macau's inner harbor cities, from anthropological and folklore perspectives.