The planetary gearing system is compact and lightweight. The performance of planetary gearing system which uses floating intermediate rings have been found to be very good for practical systems. To apply this system for the reduction of rotation of an engine, in designing stage, the quantitative estimate of the load sharing factors is required for understanding the performance. The method widely used for this purpose is to make use of elastic deformation of components of the structure or to utilize hydrodynamic oil film. This paper shows the way how to analyze the static load sharing factors by using the coefficient ''. This method can be applied for non-linear systems such as oil film bearing. The influences of various factors on '' of oil film spring are also shown. Furthermore, It is established in this study that the use of floating intermediate ring in designing the planetary gearing system has a very high reliability.

In recent years there have been large increases in the hydraulic loading rates used to design dissolved air flotation (DAF) facilities for drinking water applications. High rate DAF processes are now available at loading rates of 20 to 40 m3/m2·h. This research evaluated dissolved air flotation as a separation method for algae and organic compounds from water treatment plants. During the service period of 2016. 5. to 2017. 6., DAF pilot plants (500 m3/day) process has shown a constantly sound performance for the treatment of raw water, yielding a significantly low level of turbidity (DAF treated water, 0.21～1.56 NTU). As a result of analyzing the algae cell counts in the influent source, it was expressed at 100-120 cells/mL. In DAF treated water, the removal efficient of alge cell counts was found to be upto 90%. The stable turbidity and algae removal were confirmed by operating the high rate DAF process under the condition of the surface loading rate of 30 m3/m2·hr.

This study aimed to investigate growth rate and nutrient consumption of Chlorella vulgaris according to different light irradiation interval. Applied light irradiation intervals were 12 hr, 4 hr, 1 hr, and 1 min. The light source was flexible LED(Blue:Red=1:1), light intensity was 200 PPFD and Light/Dark cycle was 1:1. As a result, growth rate and nutrient removal efficiencies showed no significant differences depending on the light irradiation interval. Considering the reproduction characteristics of applied microalgae cultures of this study, this is thought to be one of the possible reasons of above results. Because Chlorella vulgaris performs an asexual reproduction and it is known that there is no significant relationship between light irradiation interval and growth rate, including nutrient consumption in case of asexual reproduction.

As a broad-spectrum insecticide azadirachtin may cause acute toxicity and alter behavior of natural enemies. We evaluatedthe toxicity of azadirachtin on two egg parasitoids of Riptortus pedestris (Fabricius) (Hemiptera: Alydidae), Ooencyrtusnezarae Ishii (Hymenoptera: Encyrtidae) and Gryon japonicum (Ashmead) (Hymenoptera: Platygastridae), by pre-treatinghost eggs with five concentrations, i.e., 15, 10, 7.5, 5, and 2.5 mL/L. Azadirachtin significantly reduced parasitism byG. japonicum in 15 and 10 mL/L concentrations than other lower concentrations. Similar effect was also observed inO. nezarae. The parasitism reduction capacity (R) for G. japonicum was 40.8 and 33.1% in 15 and 10 mL/L concentrations,but it was 81.6 and 71.4% in O. nezarae, respectively. Based on the IOBC guideline, azadirachtin can be slightly ormoderately harmful to O. nezarae and slightly harmful or harmless to G. japonicum.

Hay-making is one of the most common forage preservation practices in livestock operations. The objective of hay-making is to minimize nutrient loss by shortening field drying time. Measuring the impacts of cutting height of forage crop is necessary to optimize hay production balancing yield and quality, in order to obtain substantial biomass increase through harvest of regrowth. This experiment was conducted to investigate the impact of cutting height of rye (Secale cereale L.) on drying rate and hay quality. Heading stage rye was harvested at 8cm or 15cm stubble heights. Hay was daily tedded at 09:00 and sampled at 09:00, 13:00 and 17:00 to determine moisture content (MC). After two month of preservation, CP (crude protein), ADF (acid detergent fiber), NDF (neutral detergent fiber), IVDMD (in vitro dry matter disappearance), TDN (total digestible nutrient), RFV (relative feed value), DM (dry matter) loss, visual scores and total fungi count were determined for estimation of hay quality. Cutting height at 15cm could enhance the drying rate and CP content (p<0.05), but also increases DM loss (p<0.05) compared to cutting at 8cm. Cutting heights did not affect ADF, NDF, IVDMD, TDN and RFV value (p>0.05). Visual scores of rye hays cutting at 8cm and 15cm, ranged from 83 to 85. Cutting at 8cm tended to maintain higher core bale temperature and fungal count than cutting at 15cm during preservation, but there was no significant difference.

Curcumin have various health-beneficial properties in numerous studies. However, its bioavailability is low due to its limited intestinal uptake and rapid metabolism. This study aimed to evaluate the pharmacokinetics of newly developed sub-micron particle curcumin with increased water dispersibility (Theracurmin® CR-033P). Plasma curcumin levels were measured at 0, 1, 2, 4, 8 h after Theracurmin® CR-033P intake using high-performance liquid chromatography. For analyzing pharmacokinetics of Theracurmin® CR-033P, eighteen healthy subjects were recruited and received Theracurmin® CR-033P at a single oral dose containing curcumin 30 mg. Cmax was 28.14 ng/ml, and the area under the curve for 8 h was estimated to be 104.36 ng/ml. Based on the area under the plasma concentration (AUC), the bioavailability of sub-micron particle curcumin was higher 22-, 35-, 28-fold than native curcumin in men, women, and all subjects, respectively. For comparing by formulation, seven healthy subjects were recruited and received two type of treatment: (1) existing dosage form 300 mg (contained curcumin 30 mg) × 3 capsule, (2) high dosage form 300 mg (contained curcumin 90 mg) × 1 capsule + placebo 300 mg × 2 capsule. In the cross-over study, there was no significant differences in Cmax and AUC of plasma curcumin. In conclusion, submicron particle curcumin with increased water dispersibility significantly improved its oral bioavailability and women absorbed curcumin more effectively than men. Different formulation of Theracurmin® CR-033P has shown equivalent to the reference in terms of pharmacokinetics.

The artificial insemination (AI) is one of the best assisted reproductive technologies for increasing reproductive capacity and facilitating the genetic improvement in farm animals. AI has been used in Uganda for over 60 years, but a small population of the total herd has been used. This study was conducted to investigate the efficacy of AI with estrus synchronization technique and to propose ways of improving the productivity of dairy farms through AI services in Uganda. In total, 78 cows from 11 dairy farms were selected for timed-AI. Synchronization was performed according to the ovsynch programs followed by AI using frozen semen from Korean Holstein (0.5 ml straws). Pregnancy rate was varying among farms (0-50%) and the overall pregnancy rate was 28.2%. Cows in luteal phase at the time of treatment was 40.0% whereas that in follicular phase was 20.8%. After treatment, cows that showed normal estrus signal were 45.5% (25/55). Abnormal estrus was categorized into pre-estrus (9.1%), cystic ovaries (21.8%), anestrus (18.2%) and delayed ovulation (5.5%), respectively. These results imply that an assured protocol for timed-AI should be developed to improve the productivity of dairy farms through AI services in Uganda.

본 연구는 정식 후 토양의 수분 함량에 따른 배추의 생장과 토양 수분에 따른 배추의 생리 반응 모델 개발을 위한 유효 매개변수를 알아보고자 수행되었다. 처리는 5개 수준으로 각각 0, 200, 300, 400 및 500mL/d/ plant로 매일 1회 관수하여 토양 수분 함량 차이로 구분하였다. 토양수분과 기공전도도를 정식 후 10일부터 6일 간격으로 총 5회 측정하였으며(단, 0과 200mL/d/plant 처리구는 총 3회 측정), 광합성기구 활성을 알아보고자 정식 후 25일에 충분히 관수된 처리구(500mL/d/plant)와 결핍 처리구(0mL/d/plant)에서 이산화탄소 포화 곡선을 작성하였고, 정식 후 38일에 생장을 조사하였다(단, 관수 량 처리구 0과 200mL/d/plant는 위조되어 정식 후 29일에 생장 조사함). 토양수분과 배추의 기공전도도는 밀접한 관계가 있었으며(r2=0.999), 직선의 정의 상관관계로 y = 6097.4x − 4.2984였다. 충분히 관수된 배추의 이산화 탄소 포화곡선은 정상적인 포화 곡선을 보였으나, 토양 수분이 극도로 결핍된 배추는 체내로 이산화탄소가 확산 되어 들어가지 않으며, 광합성 속도도 약 6.5μmol·m-2·s-1 미만으로 급격히 감소하였다. 충분히 관수된 처리구 (500mL/d/plant)에 비하여 토양 수분 결핍구(0mL/d/plant 처리)에서는 약 6.8배 이상 건물생산량이 감소하였다. 그리고 토양의 수분 함량에 따라 엽면적 지수가 로그함수적(y = 16.573 + 3.398 ln x)으로 증가하였고, 결정 계수 r2=0.913로 높은 상관 관계가 있었다. 결과적으로, 정식 초기의 토양 수분 함량이 결핍되면 배추의 생장이 지연 되며, 광합성 속도와 기공전도도가 낮아지는 것으로 밝혀졌다. 또한, 토양수분 함량과 배추 생장 반응 모델을 기공전도도와 엽면적 지수를 변수로 활용하면 정확도가 우수한 모델을 개발할 수 있을 것으로 기대된다.

In this study, Fe-Cu-C alloy is sintered by spark plasma sintering (SPS). The sintering conditions are 60 MPa pressure with heating rates of 30, 60 and 9oC/min to determine the influence of heating rate on the mechanical and microstructure properties of the sintered alloys. The microstructure and mechanical properties of the sintered Fe-Cu-C alloy is investigated by X-ray diffraction (XRD) and field-emission scanning electron microscopy (FE-SEM). The temperature of shrinkage displacement is changed at 450oC with heating rates 30, 60, and 90oC/min. The temperature of the shrinkage displacement is finished at 650oC when heating rate 30oC/min, at 700oC when heating rate 60oC/min and at 800oC when heating rate 90oC/min. For the sintered alloy at heating rates of 30, 60, and 90oC/min, the apparent porosity is calculated to be 3.7%, 5.2%, and 7.7%, respectively. The hardness of the sintered alloys is investigated using Rockwell hardness measurements. The objective of this study is to investigate the densification behavior, porosity, and mechanical properties of the sintered Fe-Cu-C alloys depending on the heating rate.

Recently EC-MBR (Elctrocoagulation - Membrane Bio Reactor) has been suggested as one of alternative processes to overcome membrane fouling problems. Most important operational parameters in the EC-MBR are known to current density and contact time. Their effect on membrane filtration performances has been reported well, however, quantitative interrelationship between both parameters not been investigated yet. The purpose of this study is to give a kinetic model suggesting the current density and the contact time required to reduce the membrane fouling. The 4 different set of current densities (2.5, 6, 12 and 24 A/m2) and contact times (0, 2, 6 and 12 hr) were selected as operational parameters. After each electro-coagulation under the 16 different conditions, a series of membrane filtration was carried out. The membrane fouling decreased as the current density and contact time increased, Total fouling resistances under different conditions, Rt(=Rc+Rf) were calculated and compared to those of the controls (R0), which were calculated from the data of experiments without electro-coagulation. A kinetic approach for the fouling reduction rate (Rt / R0) was carried out and the equation ρi0.46t=7.0 was obtained, which means that the product of current density and the contact time needed to reduce the fouling in certain amounts (in this study, 10% of fouling reduction) is always constant.

PURPOSES :This study aims to improve complex modeling of multivariable, nonlinear, and overdispersion data with an artificial neural network that has been a problem in the civil and transport sectors.METHODS :Deep learning, which is a technique employing artificial neural networks, was applied for developing a large bus fuel consumption model as a case study. Estimation characteristics and accuracy were compared with the results of conventional multiple regression modeling.RESULTS :The deep learning model remarkably improved estimation accuracy of regression modeling, from R-sq. 18.76% to 72.22%. In addition, it was very flexible in reflecting large variance and complex relationships between dependent and independent variables.CONCLUSIONS :Deep learning could be a new alternative that solves general problems inherent in conventional statistical methods and it is highly promising in planning and optimizing issues in the civil and transport sectors. Extended applications to other fields, such as pavement management, structure safety, operation of intelligent transport systems, and traffic noise estimation are highly recommended.

The test was done on cars travelling at the speeds of 20km/h, 60km/h and 100km/h using the performance testing mode for chassis dynamometer. In this test, the secondary ignition waveform, exhaust emissions and fuel consumption were measured in case of faulty MAP sensor, faulty oxygen sensor and spark plugs. The following results from the related analysis of secondary waveform, emission and fuel consumption measurements were obtained : 1) The fuel consumption was higher in the order of oxygen sensor trouble, MAP trouble, spark plug trouble, before maintenance and after maintenance. Maximum fuel economy is 9.3km/L, the minimum fuel economy is 3.2km/L, the difference between max. and min. is 65.5%. 2) If you compare the oxygen sensor trouble with after maintenance, the CO has improved an average of 98%, fuel economy average of 60%. And the HC has improved an average of 87%, fuel economy average of 60%. The fuel consumption and exhaust gas was bad in the order of oxygen sensor trouble, MAP trouble and S/P trouble.

Recently, application areas based on M2M (Machine-to-Machine communications) and IoT (Internet of Things) technologies are expanding rapidly. Accordingly, water flow and water quality management improvements are being pursued by applying this technology to water and sewage facilities. Especially, water management will collect and store accurate data based on various ICT technologies, and then will expand its service range to remote meter-reading service using smart metering system. For this, the error in flow rate data transmitting should be minimized to obtain credibility on related additional service system such as real time water flow rate analysis and billing. In this study, we have identified the structural problems in transmitting process and protocol to minimize errors in flow rate data transmission and its handling process which is essential to water supply pipeline management. The result confirmed that data acquisition via communication system is better than via analogue current values and pulse, and for communication method case, applying the industrial standard protocol is better for minimizing errors during data acquisition versus applying user assigned method.

For the effective seedling production of the hard shelled mussel, Mytilus coruscus, this study assessed the effects of the dietary value of live food, density, water temperature and salinity on growth and survival rate of the larvae. The optimal survival rate and growth rate were examined under differing conditions of water temperature, salinity, and rearing density for 30 days. The three groups were provided different feeding organisms, such as Isochrysis galbana and Teleaulax suecica. The mixtures were provided at a rate of 5×104 cell mL-1. The best growth was observed in the group with conditions 21℃ water temperature (16.2±9.1 μm), 33 psu of salinity (16.82±3.9 μm), 2500 individual m-2 (17.2±5.9 μm), and fed with 5×104 cell mL-1 of I. galbana and T. suecica mixture (16.0±7.3 μm). The highest survival rate was found in the group at conditions 18℃ water temperature (66.4%), 33 psu of salinity (24.4%), 2500 individual m-2 (65.8%), and fed with 5×104 cell mL-1 of I. galbana and T. suecica mixture (58.8%). We therefore conclude that the suitable culture conditions for the stable production of hard shelled mussel artificial seedlings was at 18 to 21℃ of temperature, 30 to 33 psu of salinity, 2500 to 5000 individual m-2 of rearing density, and feeding supplement of 5×104 cell mL-1 of I. galbana and T. suecica mixture under semi running water system.

Embryo transfer is one of the important process of assisted reproductive technology (ART) and that is associated with uterus endometrial receptivity. Recently, mouse endometrial stimulation by artificial injury had shown the favorable effect on conception. In this experiment, we used uterus stimulation method that injury the endometrium to increase implantation rate for spontaneous Diabetes Mellitus (sDM) rat. Rats are divided into several groups involved a control group. We performed the surgical method to Experimental group bilaterally or unilaterally After that, we investigated morphological change and calculated implanted embryos respective sides of the uterus. The number of implanted embryo in the experimental group was significantly higher and there were lots of morphological changes including glands and endometrial cells that support implantation. Our results showed that rat uterus endometrial injury in ART help enhancing implantation rate.

역삼투 공정은 현재 해수담수화 공정으로 가장 많이 사용되는 공정으로 향후 지속적으로 사용량이 증가될것으로 보인다. 보론은 인체와 동물, 식물에게 필수적인 영양소이지만, 과잉 공급된 보론은 인체 및 식물의 신경계 장애 및 생식능력 저하를 초래하고, 식물성장 및 과실의 성장을 방해하는 독성물질로 의심받고 있다. 보론은 흔히 쓰이는 하수처리 및 폐수처리 공정에서 제거되지 않으며, 역삼투 공정에서도 중성인 B(OH)3로 남아 있어 역삼투 후에 보론 한계기준보다 훨씬 높은 농도가 생산수에 존재하는 경우가 종종 있다. 그래서 물에서 보론이 제거되는 공정이 절실한 상황이다. 본 연구에서는 보론 제거율 향상을 위해 첨가제를 활용한 polyamide를 계면중합을 통해 합성하여 역삼투막을 제조하였으며, 제조된 역삼투막의 성능평가를 수행, 비교하였다.

Differences in sugar and salt penetrarion rates of radish depending on size and concentration of solution were examined. 2x2x2 and 4x4x4 cm cube-shaped radish examined in different pickling condition (salt 2, 4, 6, 8% and sugar 5, 10, 15, 20% brix). After 12hr storage, Salt penetration rate of radish cut into 2x2x2 cm was faster than that of 4x4x4 cm in all salt solution. Size dependent sugar penetration showed same tendency with size dependent salt penetration. Also, increase in salt and sugar concentration led to increase in salt and sugar permeation rate.