The water distribution system should be invariably operated on continuous pattern for 24 hours a day. Occasionally, it is not practically possible to operate for 24 hours due to water shortage or financial constraints. Therefore an intermittent water supply is unavoidable in water shortage area and developing countries.But the intermittent water supply can introduce large pressure forces and rapid fluid accelerations into a water supply network. These disturbances may result in new pipe failure, leakage and secondary contamination.This paper proposed an improvement methodology to prevent the disturbances by intermittent water supply. For the study, the hydraulic variation of intermittent flow in water distribution system was measured and analyzed in the field by comparing with simulation of hydraulic model. Installations of control valves such as, pressure reducing and sustaining and air valves were employed for pressure and flow control. The effectiveness of the methods are presented by comparing hydraulic conditions before and after introducing the proposed solutions.

It is intended to develop an experimental apparatus which can visualize flow patterns in condensate water reuse system with various cross sections. PVC particles on fluid surface help to obtain clear flow images. The flow region that were found in the experiments are steady, unsteady and significantly-mixed flows.

The hydrofoil-tip mixer can be used to create the desired material by mixing the two materials in various industries, especially in the waste water and sewage water treatment. The purpose of this study is to clarify flow characteristics induced by 3 types impellers in a mixing tank by CFD. In this study, flat plate, hydrofoil and hydrofoil-tip type impellers are used and the rotating speeds of impellers are 25, 35, 45 rpm. The results in present study show that hydrofoil-tip type is the most proper impeller for mixing in the waster water treatment tank and reducing required power of rotating impeller. This results can be used for the design of the mixing tank in the waste water treatment system.

The flow rate analysis for sanitary fixtures has been studied to determine the water supply piping system and size. The study has been carried out to analyze for a various water supply pressure and piping size theoretically. Also, the study has been carried out to analyze for a various water supply piping system experimentally. The water supply pressure is varied from 0.01MPa to 0.07MPa, and the piping size is varied from 6mm to 15mm. The water supply piping systems are one-to-one, all-loop-type, and bathroom-loop-type water supply piping system. The results indicate that the piping size is able to supply water fully in case of smaller than 15mm if the water supply pressure keep an necessary minimum pressure. And the gap of flow rate is very little for the various water supply piping systems

Ballast water of ten billion tons are transferred by the ship annually in the world. Because alien creatures are destroying aquatic ecosystems, ballast water treatment is needed. Physical methods of treatment using the filtration method is hydrocyclone. The advantage of hydrocyclone is to create a simple structure and a easy separation of good performance. A commercial CFD code CFX 11.0 is applied to analyze hydrocyclone. According to the shape changes of the hydrocyclone, separation performance was compared. The results show that when you reduce the height of hydrocyclone, hydrocyclone separation efficiency is lowered.

The purpose of this present study is to measure the changes of regional cerebral blood flow(rCBF) was continually monitored by laser-doppler flowmeter (Transonic Instrument, USA) through the data acquisition system composed of MacLab and Macintosh computer. Contractile force was measured with force displacement transducer under 1.5 g loading tension. Rhus verniciflua stokes increased the changes of rCBF in rats, significantly. The rCBF of Rhus verniciflua stokes was decreased by pretreated propranolol, l-NNA and methylene blue. But atropine indomethacin did not change the rCBF. Contractions evoked by PE 0.1μM were significantly inecreased by Rhus verniciflua stokes. Propranolol significantly altered the effect of Rhus verniciflua stokes, but l-NNA, ODQ and indomethacin did not change the relaxation of Rhus verniciflua stokes. These results suggest that Rhus verniciflua stokes can increase the rCBF and relax EP induced contraction of isolated rat aorta, and that is related to sympathetics and nitric oxide.

열수지 경류센서에 의한 멜론의 흡수량 측정오차는 최저 0.3%에서 최대 31.8% 범위 내에 있었으며, 일사량 20MJ.m-2 .d-1에서는 오차가 적었으나 일사량이 이보다 많아지면 많아질수록 센서측정 경류량이 실측양액 소비량보다 적어지는 경향이었고 일사량이 적어질수록 센서측정 경류량이 실측양액 소비량보다 많아지는 경향이었다. 센서간의 오차는 최저 0.1%에서 최대 13.0%의 오차율을 보였다. 열수지센서측정 경류량은 일사량이나 온도와 고도의 부의 상관관계를 보였다. 그러므로 이를 이용 보정계수를 산출하면 보다 정확한 멜론의 경류량을 측정할 수 있을 것으로 판단되었다.

예망어구의 유체역학적인 특성과 예망어구내에서의 유속 측정 자료를 기초로 어류의 측선 유수감각에 작용하는 유효한 유수자극량을 추산하고 정량화하기 위하여 예망어구내의 3차원적인 상대유속의 선형적인 분포정도를 모델링하였다. 예망어구내의 상대유속은 망지의 제반규격과 예망어구의 수중 전개형상에서의 각부 거리비에 따라 상대유속비를 선형적으로 수식화하여 본문의 식(3)과 (8)로 표현하였다. 이러한 상대유속비는 어류의 측선 유수감각기관에 의하여 탐지될 수 있는 와동 유수자극량의 지표로써 사용될 수 있다. 어류의 유수감각 예민도는 어류의 전장과 어체주위 상대유속에 의하여 선형적으로 변화되는 것으로 가정하고 본문의 식(9)와 같이 탐지가능한 상대유속차의 최소값으로 나타내었다. 예망어구내의 상대유속 분포에 관한 본 모델의 계산 결과는 실물예망어구에서 실측된 상대유속의 범위내에서 거의 근사하게 나타났으며 본 모델은 어류의 대망행동 모델링에서 예망어구의 유수자극과 어류의 유수감각 예민도를 상대적으로 정량화하여 어류행동의 반응요인으로 적용할 수 있을 것이다.

To use effectively the solar energy in greenhouse heating, a high performance solar collector should be developed. And then the size of the solar collector and thermal storage tank should be determined through the calculation of heating load. The solar collector must be set in the optimum tilt angle and direction to take daily solar radiation maximally, and the flow rate of heat transfer fluid through the solar collector should be kept in the optimum range. In this research, the performance tests of a capillary tube solar collector were performed to determine the optimum water flow rate and the results summarized as follows. 1. The regressive equations for efficiency estimations of the capillary tube solar collector in the open loop were modeled in the water flow rate of 700-l,000 l/hr. 2. The optimum water flow rate of the solar collector was estimated by the second order polynomial regression and the maximum efficiency was 80% at the water flow rate of 850 l/hr. 3. The solar thermal storage system consisted of a capillary tube solar collector and a water storage tank was tested at the water flow rate of 850 l/hr in the closed loop, and obtained the solar thermal storage efficiency of 55.2%. 4. As the capillary tube solar collector engaged in this experiment was made of non-corrosive polyolefin tubes, its weight was as light as 1/30 of the flat plate solar collector made of copper tubes. Therefore it was considered to be suitable for the greenhouse heating system.

The purpose of this study at water quality pollutants to propose proper management method for the Osu-A unit watershed which is the influent tributary located upstream of the Sumjin -river among the 13 unit watersheds in the Sumjin-river water system. Analyzed the correlation between flow-pollution loading and the correlation between land use type, BOD and TP items, and analyzed 8-day intervals Cumulative Flow Duration Curve (CFDC) and Load Duration Curve (LDC) to evaluate water quality damage. As a result, both BOD and TP were larger than 1 and the concentration of water pollutants increased with increasing flow. BOD was positively correlated with Urban and Field, and TP was positively correlated with Field with 0.710. As a result of the LDC, BOD was analyzed that the target water quality was achieved with the excess rate of less than 50%, and TP exceeded the target water quality by 50.1%. BOD usually exceeded the standard value (exceedance probability 50%) at low flow zone and On the other hand, TP usually exceeded the standard value at high flow zone. Monthly BOD (April to June) and TP (May to August) exceeded the standard. Sewage Wastewater treatment and non-point pollution control is Osu-A unit watersheds are effective in improving BOD and TP.

홍수조절지는 하천 제내지 측에 제방을 축조하고 제방 일부 구간에 횡월류위어를 설치해 일정규모 이상의 홍수사상 발생 시 홍수량 일부를 월류시켜 저류하는 홍수저감시설이다. 다양한 하천시설물이 존재하는 하천 내에서 홍수조절지의 운영 최적화를 위해서는 기존 시설과의 연계 운영을 함께 검토해야 할 필요가 있다. 본 연구에서는 하도 내 수문 시설의 영향을 고려해 홍수조절지 횡월류위어의 위치 변화에 따른 수로 내 수위 저감 및 유량 분담 효과를 분석하였다. 수문 시설의 영향을 고려하기 위해 수로 내 2문의 방사형 수문을 설치하였으며, 수문으로부터 상류 방향으로 횡월류위어의 위치를 이동시키며 수로 내 수위 변화와 횡월류위어의 월류량을 측정하였다. 실험 결과 횡월류위어의 위치가 수문에 가까울수록 수위 저감 효과가 크게 나타났으며, 유량 분담 효과는 큰 변화가 없는 것으로 확인되었다. 2개소 이상의 횡월류위어 운영 시에는 충분한 저류공간이 확보되어 횡월류 위어의 위치에 따른 수위 저감 효과의 변화가 크지 않은 것으로 확인되었다. 또한, 수문 운영 시 1개소 횡월류위어의 위치 변화에 따른 수위 저감율 을 경험식으로 산정해 향후 홍수조절지 계획 시 활용 가능한 기초자료를 제공하고자 한다.

Recently severe drought caused the water shortage around the western parts of Chungcheongnamdo province, South Korea. A Diversion tunnel from the Geum river to the Boryong dam, which is the water supply dam for these areas has been proposed to solve this problem. This study examined hydraulic impacts on the Geum river associated with the diversion plan assuming the severe drought condition of 2015 would persist for the simulation period of 2016. The hydraulic simulation model was verified using hydrologic and hydraulic data including hourly discharges of the Geum river and its 8 tributaries, fluctuation of tidal level at the mouth of the river, withdrawals and return flows and operation records of the Geum river barrage since Feb. 1, 2015 through May 31, 2015. For the upstream boundary condition of the Geum river predicted inflow series using the nonlinear regression equation for 2015 discharge data was used. In order to estimate the effects of uncertainty in inflow prediction to the results total four inflow series consisting of upper limit flow, expected flow, lower limit flow and instream flow were used to examine hydraulic impacts of the diversion plan. The simulation showed that in cases of upper limit and expected flows there would be no problem in taking water from the Geum river mouth with a minimum water surface level of EL(+) 1.44 m. Meanwhile, the simulation also showed that in cases of lower limit flow and instream flow there would be some problems not only in taking water for water supply from the mouth of the Geum river but also operating the diversion facility itself with minimum water surface levels of EL(+) 0.94, 0.72, 0.43, and 0.14 m for the lower limit flow without/with diversion and the instream flow without/with diversion, respectively.

This study, examines the flow characteristics of upstream channel depending on water gate operation of Nakdan Multi-fuctional weir. The specific purpose of this study are to simulate the variation of flow velocity depending on the operation of the weir using 1-dimensional hydraulic model, HEC-RAS, and compare it with observed velocity. For discharge conditions from 50 ㎥/s to 3,500 ㎥/s, it is observed that the velocity of upstream channel is almost constant, whereas for probability flood discharge, the velocity and froude number are increased as the discharge values are increased. The velocity values for downstream boundary condition EL, 40.0 m are more decreased than those for EL. 40.5m. From comparison on the variation of water stage depending on water gate operation, it is observed that the stage values are almost constant for discharges below 300 ㎥/s, whereas 5 cm to 20 cm for discharges over 700 ㎥/s. Flow velocity at streamflow gauging station. Nakdong, is decreased by more than 875% after installing the weir. The results obtained from this study indicate that the velocity of upstream channel is decreased and the discharge and velocity of downstream channel are significantly varied after installing the weir.

기포가 포함된 다상흐름의 측정은 중요함에도 불구하고 많은 제약이 있었다. 특히, 공극률이 높은 다상 흐름은 밀도차의 급격한 변화와 두꺼운 공기-물 경계면으로 인해 측정이 매우 어렵다. 본 연구에서는 공극률에 상관없이 기포흐름을 측정할 수 있는 기포영상유속측정법과 다발 광섬유유동측정계를 소개하고자 한다. 기포영상측정기법의 경우, 화상측정시 발생하는 원근에 의한 오차를 최소화하고 추정할 수 있는 피사계 심도에 대한 계산방법을 제시하여 정도 분석을 위한 방안을 제시하였다. 다발 광섬유유동측정계는 얇은 광섬유의 특성을 이용해 다발로 제작하여 측정률을 증가시키고자 하였다. 제시된 두 기법을 기포플룸에 적용하여 신뢰도를 검토하였으며 잘 일치하는 것을 확인하였다. 소개된 기법으로 대표적인 하천 다상흐름인 도수흐름을 측정하여 그 적용성을 검토하였다.

Detection of water bodies and their flow paths is elemental process of terrain analysis in any application related with surface water. Several algorithms have been proposed for automatic extraction of surface flow paths from Digital Elevation Models (DEMs) (e.g., O’Callaghan and Mark, 1984; Tarboton, 1997; Paik, 2008). While these algorithms have been widely applied, DEMs-based approaches have fundamental limitation in detecting water bodies. To resolve this issue, we propose a hybrid approach that utilizes DEMs and satellite imagery together. These dataset supplement each other’s weakness, providing extra information for better detection of water bodies and flow paths. The proposed approach is tested for the Geum River, showing successfully extraction of flow boundaries and more resonable flow paths within water bodies.

대경사 수로의 부등류에 대해 적용될 수 있도록 수정된, 새로운 정수압 분포를 제시하였다. 이것을 천수방정식에 적용하여 대경사를 지나는 천수 흐름을 정확하게 해석할 수 있는 유한체적 모형을 개발하였다. 포물선형 융기의 배수에 대해 압력 수정이 고려된 모형에서 바닥 경사 생성항의 영향이 줄어들어 융기의 하류에서 도수의 진행 속도가 크게 감소되었다. 삼각형 턱을 지나는 댐 붕괴 흐름에 대한 모의에서 압력 수정항이 추가된 모형으로 디지털 영상분석에 의한 수면을 압력 수정이 고려되지 않은 경우에 비해 더 잘 포착할 수 있음을 확인하였다. 압력 수정항 덕분에, 턱에 반사되는 흐름은 줄어들고 월류는 늘어 모의 결과가 실험 결과에 잘 부합된다. 따라서 댐의 여수로나 해안의 처오름 등 실용적인 문제에 대한 이 모형의 적용성이 기대된다.

우리나라는 지형적인 특성과 높은 인구밀도로 인해 1인당 수자원 부존량이 부족한 상황이다. 이에 이상 기후현상과 여름에 집중되는 호우로 인한 가뭄이나 홍수에 효율적으로 대비하기 위해 2009년 하반기부터 4대강 사업이 추진되었고 2013년 현재 공사가 끝난 상황이다. 낙동강은 4대강 사업이 진행된 우리나라 주요 하천 중 사업이 진행된 길이가 가장 길고 수공구조물(보)이 가장 많이 설치되어 있다. 본 연구에서는 낙동강에 개설된 관측소들 중 다른 곳에 비해 지류의 유입이 적어 유량의 변화가 적고 그 사이에 수공구조물이 상대적으로 많이 설치되어 있는 낙동관측소와 왜관관측소를 연구대상으로 선정하였다. 보 설치 이전인 2009년 5,6,7월과 설치가 끝난 2013년 5,6,7월의 유량과 수위의 변화를 비교, 분석하여 수문변화에 대해 파악해 보았다. 수공구조물(보)가 설치되고 나서 상류(낙동관측소)와 하류(왜관관측소)간의 유량차가 감소하였고 상 하류 모두 강우량에 영향을 거의 받지 않고 낙동관측소와 왜관관측소에서 일정한 값의 수위를 유지하는 것을 알 수 있었다. 또한 최대 수위변화폭도 보 설치 이후인 2013년에 감소하였다. 이를 토대로 보 설치 이후 강우량에 의한 유량 및 수위변화가 적은 것으로 나타났으며 이상기후로 인해 발생하는 가뭄이나 홍수의 수문학적 영향이 적을 것으로 판단된다.