This paper validates a system identification method using mathematical optimization using sea trial measurement data as a benchmark. A fast time simulation tool, SIMOPT, and a Rheinmetall Defence mathematical model have been adopted to conduct initial hydrodynamic coefficient estimation and simulate ship modelling. Calibration for the environmental effect of sea trial measurement and sensitivity analysis have been carried out to enable a simple and efficient optimization process. The optimization process consists of three steps, and each step controls different coefficients according to the corresponding manoeuvre. Optimization result of Step 1, an optimization for coefficient on x-axis, was similar compared to values applying an empirical regression formulae by Clarke and Norrbin, which is used for SIMOPT. Results of Steps 2 and 3, which are for linear coefficients and nonlinear coefficients, respectively, was differ from the calculation results of the method by Clarke and Norrbin. A comparison for ship trajectory of simulation results from the benchmark and optimization results indicated that the suggested stepwise optimization method enables a coefficient tuning in a mathematical way.

Rockfish was a commercially important fish specie in marine ranching areas in Korea. To estimate density and biomass of rockfish using acoustic method, target strength (TS) information is required on the species. This study measured TS dependence on tilt angle and size on 14 live rockfish individuals at 38, 70, and, 120 kHz by ex-situ measurement (tethered method) and acoustic scattering model (Krichhoff ray mode, KRM). The swimbladdered angle ranged from 18 to 30˚ (mean ± s.d. = 26 ± 4˚ ). The mean TS for all individuals was highest -35.9 dB of tilt angle -17˚ at 38 kHz, -35.4 dB of tilt angle -25˚ at 70 kHz, and -34.9 dB of tilt angle -22˚ at 120 kHz. The ex-situ TS-total length (TL, cm) relationships were TS38kHz = 20log10(TL) - 67.1, TS70kHz = 20log10(TL) - 68.6, and TS120kHz = 20log10(TL) - 69.9, respectively. The model TS-total length (TL, cm) relationships were TS38kHz = 20log10(TL) - 66.4, TS70kHz = 20log10(TL) - 67.0, TS120kHz = 20log10(TL) - 67.0. The two measurements between the ex-situ TS and KRM model for TS-tilt angle and fish size were found to be significantly correlated.

This study was conducted to explore portion size estimation by comparing the measurement errors of food and macronutrient intake by photography estimation and 24-hour recall from weighing method. A total of 28 female participants aged 20-24 years old were provided a meal that included rice, chard soup with soybean paste, stir-fried squid, japchae, stirfried boiled fish paste, lettuce geotjeori, and kimchi. Each portion was measured accurately, and food intake was measured using three dietary assessment methods. For the photography method, trained researchers estimated remaining food amount by analyzing photographs using a mean of four times. The measurement errors for the stir-fried squid and japchae were larger by the 24-hour recall method, while the error for kimchi was larger by the photography method. The correlation coefficients for each food, except chard soup with soybean paste, between the weighing method and photography method were 0.77~0.99 (p<0.001). The correlation coefficients of energy and intake of macronutrients between the weighing method and photography method were 0.85~0.86 (p<0.001). The results of this study demonstrate substantially less measurement error using the photography method than the 24-hour recall method. However, further research is needed to standardize various kinds of foods, photograph angles, serving plates, and serving style for establishment of reliable and valid portion size estimation using the photography method.

The purpose of this study is to accurately estimate the wind-induced responses of a tall building structure for using the estimated responses in the process of calculating the optimal force of an active control device. Kalman filter was used for the estimation process and a 3-storied model structure on a shaking table was tested for the verification of the estimation accuracy. The system matrices of the model were constructed based on the mode parameters obtained by the system identification. The estimated displacement matched up well with the measured one. Finally, the wind-induced responses of a real 39-storied building structure excited by the typhoon MUIFA were estimated.

구조용 강재의 용접부는 강재(Base metal, BM), 용접모재(Weld metal, WM), 열영향부(Heat affected zone, HAZ)로 구성된다. 용접부를 구성하는 이들 세 부분의 구조적 성질은 서로 다를 것이므로, 강재의 용접부의 구조 거동은 BM, WM, HAZ로 구성된 복합체의 거동으로 고려할 수 있다. 본 연구에서는 용접부를 구성하는 BM, WM, HAZ 각각의 탄성계수를 나노압입으로 도출하고, 이들의 복합거동(composite action)을 고려한 용접부의 등가탄성계수(equivalent elastic modulus)를 산정하였다.

This study was conducted to estimate the growth parameters of Holstein cows and to compare their growth characteristics based on weight-age data of Holstein cows of 293 heads from National Institute of Animal Science in Korea. Three models(Gompertz, von Bertalanffy and Logistic model) were considered for analyses. The estimated growth functions for Gompertz, von Bertalanffy and Logistic models were Wt=781.0e−2900e−0.09521t,Wt=943.3(1−0.650e−0.06231t)3 and Wt=665.7(1+13.475e−0.18260t)−1 , respectively. The estimated average infection points(ti) showing maximum growth rate were 352.034, 338.181 and 430.987 day of age, respectively, using on Gompertz, von Bertalanffy and Logistic model. Average gain at inflection for Gompertz, von Bertalanffy and Logistic model were estimated 0.878, 0.833 and 0.986 kg/day, respectively. The estimated weight at inflection for Gompertz, von Bertalanffy and Logistic model were 301.5, 279.5 and 332.9 kg, respectively. In the study, the von Bertalanffy model having a variable point of inflection fitted the best for data of Holstein cows.

This study was conducted to evaluate the effect of site quality on allometric equations, stem density and biomass expansion factors(BEFs) in a 20-year-old Machilus thunbergii plantation. The study site was located in Jindo county, Chollanam-do, southern Korea. Total 14 trees were harvested from the good site(tree height: 6.7 m) or poor site(tree height: 4.6 m) assumed by tree height growth. Allometric equations, stem density and biomass expansion factors were calculated from the sampled trees. Site-specific allometric equations of tree components were significant(p<0.05) with diameter at breast height(DBH). Also, generalized allometric equations could be applied to estimate tree biomass regardless of the difference of site quality because of no significant effect on slope of site-specific allometric equations. Aboveground tree biomass was significantly higher in the good site(81.0 Mg ha-1) than in the poor site(46.3 Mg ha-1). Stem density was not significantly different between in the good site(0.65 g cm-3) than in the poor site(0.67 g cm-3), whereas aboveground tree and leaf BEFs were significantly higher(p<0.05) in the poor site(aboveground: 2.23; leaf: 0.42) than in the good site(aboveground: 1.82; leaf: 0.23). The results indicated that aboveground Biomass and Biomass expansion factors of a Machilus thunbergii plantation were affected by site quality.

This study aimed to estimate the odor emission rate from swine nursery facilities (naturally and mechanically ventilated) using probability distribution. Odor occurrence trends in the study facilities were very different; odor concentration and gas flow had a lognormal distribution. Monte Carlo simulation was used to carry out the uncertainty analysis. Odor emission rate was found to range from 18.05 OU/sec (10th percentile) to 621.88 OU/ sec (90th percentile), and odor emission rate per head ranged from 0.02 OU/sec · head (10th percentile) to 0.64 OU/ sec · head (90th percentile).

Greenhouse gas emission from agricultural land is recognized as an important factor influencing climatic change. In this study, the national CO2 emission was estimated for paddy soils, using soil GHG emission model (DNDC) with 1 km2 scale. To evaluate the applicability of the model in Korea, verification was carried out based on field measurement data using a closed chamber. The total national CO2 emission in 2015 was estimated at 5,314 kt CO2-eq, with the emission per unit area ranging from 2.2~10.0 t CO2-eq ha-1. Geographically, the emission of Jeju province was particularly high, and the emission from the southern region was generally high. The result of the model verification analysis with the field data collected in this study (n=16) indicates that the relation between the field measurement and the model prediction was statistically similar (RMSE=22.2, ME=0.28, and r2=0.53). More field measurements under various climate conditions, and subsequent model verification with extended data sets, are further required.

본 논문에서는 강낭콩의 생산이나 이송과정에서, 곰팡이나 충격으로 인한 변색과 변형이 섞인 강낭콩 군집 에서 정상립을 선별하는 방법을 제안한다. 곰팡이로 인한 변색을 선별하기 위해서 개체별로 표면의 회색 화소를 추정 하는선별 인자를 제안하였고, 충격으로 인한 조각 변형이나 변형 이후 외부 변색을 동시에 고려하기 위해서 는 화소별로 R-G값과 G-B값의 차이 비교를 이용한 선별 인자를 제안하였다. 제안한 두 개의 선별인자를 이 용하여 문턱치 기반의 실시간 선별 알고리즘을 각 100씩의 개체를 갖는 정상립과 두 종류의 불량립에 대해 적용한 결과, 선별 정확도는 최적 환경에서 얻은 강낭콩 영상에 대해서는 99%의 정확성을 보였고, 블러링 및 조명 열화로 인한 환경에서 얻은 강낭콩 영상에 대해서는 각각 98.67%와 96.33%의 성능을 보였다.

To estimate pollution sources in the watershed with various industries, the simulation of contamination route and distribution of 2-methyl-4,6-dinitriophenol(DNOC) were performed with a numerical model Hydro Geo Sphere. This study was performed calculations of the load using the measured concentration and simulated flow rate. And, the river was divided by the sampling sites at the mainstream, and the contribution rate at downstream sampling sites was calculated for each section. The results showed the concentration of the downstream sampling sites were decided by the concentration of upstream sites, and the contribution rates of the tributaries were calculated below 10%. The results also showed that the impact of the potential sources in Section 1(Geumho1 ~ Geumho2) and Section 5(Geumho5 ~ Geumho6) was larger than in the other area. In Section1 and Section5, It seemed to require detailed investigation.

In this study, to estimate the combination of earthquake magnitude (Mw) and distance (R) corresponding to the design spectrum defined in Korean Building Code (KBC) 2016, the response spectra predicted from the attenuation relationships with the variation of Mw (5.0~7.0) and R (10~30km) are compared with the design spectrum in KBC 2016. Four attenuation relationships, which were developed based on local site characteristics and seismological parameters in Southern Korea and Eastern North America (ENA), are used. As a result, the scenario ground motions represented by the combinations of Mw and R corresponding to the design spectrum for Seoul defined in KBC 2016 are estimated as (1) when R =10 km, Mw = 6.2~6.7; (2) when R = 15 km, Mw = 6.5~6.9; and (3) when R = 20 km, Mw = 6.7~7.1.

Recently, remote sensing technology as a nondestructive method has been utilized to detectthe quantity and quality of crops using unmanned aerial system. To predict vegetation growth(leaf dry mass and nitrogen content) of soybean, two vegetation index(NDVI and Green NDVI)were calculated from images acquired by multi-spectral camera mounted on a UAV and eachprediction models between vegetation growth and index were evaluated. As a result, there wasno significant difference between vegetation growth and index when each vegetation stage foreach yellow and black bean were compared to each other. However, there was significantdifference between vegetation growth and index when all vegetation stage for each yellow andblack bean were compared to each other. Moreover, there was significant difference betweenvegetation growth and NDVI(r= 0.799 for leaf dry mass, r= 0.796 for nitrogen content), andGreen NDVI(r= 0.860 for leaf dry mass, r= 0.845 for nitrogen content) for all vegetation stageswith all soybeans. The accuracy and precision of Green NDVI model(R2= 0.740 for leaf drymass, R2= 0.714 for nitrogen content) were better than those of NDVI model regardless ofvarieties and vegetation growth. Therefore, Green NDVI has considerable potential to detect thequantity and quality of soybeans.

SCM activities in a company are considered as total innovation through synchronizing supply and demand while maintaining appropriate inventory level and reducing the business operating costs. Until now, even several researches are carried out on the SCM performance of the companies which have introduced and been operating SCM, the research on the cost analysis for the inventory which occurs frequently on supply chain is still insufficient. Especially, for the electronics industry in which the product depreciation is sharp caused by the short product life cycle and the complexity of distribution channels, even the inventory related costs are a major factor in business management, since the current estimated criteria of inventory costs are limited to the interest and maintenance management costs, the criteria do not reflect the total influence of the product depreciation and lost opportunity cost which are related to the business management. Furthermore, even though the rapid price drops of the distributor inventory caused by the frequent new model launch can be covered by the product manufacturers, the scale of total costs related to the inventory has not been conceived because the price compensation is traditionally considered as a market costs.In this research, we analyzed the inventory characteristics of electronics industry in which the price depreciation happens frequently, newly defining the estimated criteria of the product total inventory cost which includes price depreciation from the product manufacturers’ view. Finally we focus on the case study of a representative electronics company and verify the scale of the influence on management performance.

멸종위기종 개체군의 연령구조를 파악하는 것은 개체군의 변동에 관한 정보를 제공할 수 있기 때문에 중요하다. 본 연구에서는 환경부 멸종위기종 Ⅱ급과 문화재청 천연기념물로 지정되어 있는 남생이 (Mauremys reevesii)의 등갑에 나타나는 성장선으로 실제 연령을 신뢰성 있게 예측할 수 있는지를 평가하였다. 실험개체는 실 연령이 1-9살인 서울동 물원에서 사육하는 100개체였다. 성장선은 중앙 추갑판 네 개와 좌우측 첫 번째 늑갑판에서 측정하였다. 연구결과 실 연령 1-5살까지는 성장선의 수가 실 연령보다 많았으나, 6-9살에는 성장선의 수가 실 연령보다 적었다. 실 연령과 성장선 연령을 비교 평가한 결과 성장선으로 실 연령을 예측하는 것은 6살 이하에서 제한적으로 가능한 것으로 나타났 다. 본 연구에서 또한 어린 개체와 암컷 남생이들의 등갑의 길이와 너비를 이용하여 나이를 예측하는 수식을 제공하였으 나 연구에 사용한 남생이들의 나이가 실 연령이 어린개체들이 대부분이어서 신뢰성 있는 연령예측은 가능하지 않았다. 종합하면, 등갑에 나타난 성장선을 이용하여 남생이의 실 연령의 예측하는 경우, 성장선 6개 이하는 성장선 수의 최소값을 7개부터는 최대값을 이용하는 것이 가능한 실 연령과의 편차를 줄 일 수 있음을 보여준다. 우리의 연구결과가 비록 제한적이기는 하지만, 국내에서 거북류의 성장선의 수를 이용하여 실 연령을 예측한 첫 번째 연구로, 야외에서 멸종위기종인 남생이의 연령을 평가할 때 유용하게 사용될 것으로 판단된다.

For driver convenience, different types of transmission are being developed, such as AT(Automatic Transmission), AMT(Automated Manual Transmission), CVT(Continuously Variable Transmission) and DCT(Dual Clutch Transmission). To improve ride comfort and durability of the transmission, control system is important during launching and shifting process. For accurate control, vehicle mass and road gradient should be known. In this study, heavy duty vehicle’s mass and road gradient estimation method is developed. The method uses only signals from CAN(Controller Area Network) without applying extra sensors. Vehicle mass and gradient is estimated by LMS(Least Mean Square) method based on longitudinal vehicle dynamic model. To verify the estimation logic, test was conducted using a chassis dynamometer. The estimation results after test and test condition is compared. The error rate of vehicle mass estimation was 5 percent and gradient estimation result had 2 percent error.

Price quotations for SOR / RFQ from OEM clients is a very important process in the automotive parts industry. However, OEM clients are demanding a price quote on short duration but it takes long delivery time due to sales, research and development, purchasing, production and cost management departments role and jobs focused on detail and responsibility. And to provide a reasonable alternative with eliminating the waste of non-value processes is to achieve OEM clients satisfaction through standardized and parallel processing, IT system based on the systems and processes of global benchmark companies.

2011년 중국은 전체특허출원 수에서 미국을 제치고 1위를 차지하여, 현재 특허 생산 1위의 국 가로 부상하게 되었다. 따라서 중국에서의 특허분 쟁사례도 증가되는 추세이고 글로벌 기준에 맞추 기 위하여 빈번한 법률 개정도 진행하고 있는 상 황이다. 중국 특허법 제65조에 따르면, 순차적으 로 권리자의 실제손실, 침해자의 이익, 특허실시 료의 배수, 법정손해배상액 등 계산방식을 적용하 여 산정할 수 있지만 실무에서는 손해배상 산정방 식이 상당히 경직된 모습을 보이고 있다. 한편 미국은 다양한 방법으로 일실이익을 산정 하는데 그 기준으로서 Panduit 테스트를 적용하 고 있고 상세한 입증책임도 확립되어있다. 또한 기술융복합제품에 대한 산정법리로 중국은 기여 도 배분의 원칙만 사법해석에 규정되고 있지만 미 국은 전체시장가치 원칙도 판례에서 적용한 바가 있다. 따라서 본 논문에서는 미국의 심층적인 논 의를 참고하여 중국 손해배상 산정방식에 대한 개 선방향을 제언하고자 한다.

본 연구에서는 신갈나무와 졸참나무 임분의 입지환경인자 및 기후인자 자료를 활용하여 출현확률을 평가하였으며, 자료 분석은 Binary logit model을 이용하였다. 추정 결과, 신갈나무는 해발이 높고, 산복이나 산정의 지형에서 확률이 높게 나타난 반면 졸참나무는 대체로 해발고가 높지 않으며, 평탄지와 완구릉지에 비하여 산록과 산복의 지형에서 확률이 증가되는 경향이 나타났다. 그 외 적색산림토양군의 토성을 가지는 지형과 점토군이 아닌 미사군과 모래군으로 갈수록 출현확률이 높아지는 공통적인 특성이 나타났다. 본 연구의 결과는 장기적인 산림경영 측면에서 조림수종 선정에 유용하게 활용 될 수 있을 것으로 사료된다.