In mobile communication systems, location management deals with the location determination of users in a network. One of the strategies used in location management is to partition the network into location areas. Each location area consists of a group of cells. The goal of location management is to partition the network into a number of location areas such that the total paging cost and handoff (or update) cost is a minimum. Finding the optimal number of location areas and the corresponding configuration of the partitioned network is a difficult combinatorial optimization problem. This cell grouping problem is to find a compromise between the location update and paging operations such that the cost of mobile terminal location tracking is a minimum in location area wireless network. In fact, this is shown to be an NP-complete problem in an earlier study. In this paper, artificial bee colony (ABC) is developed and proposed to obtain the best/optimal group of cells for location area planning for location management system. The performance of the artificial bee colony (ABC) is better than or similar to those of other population-based algorithms with the advantage of employing fewer control parameters. The important control parameter of ABC is only ‘Limit’ which is the number of trials after which a food source is assumed to be abandoned. Simulation results for 16, 36, and 64 cell grouping problems in wireless network show that the performance of our ABC is better than those alternatives such as ant colony optimization (ACO) and particle swarm optimization (PSO).

The electromagnetic interference(EMI) shielding sheet of grid pattern for the wireless charger has been designed by using grid pattern metal sheet, PET & DST stacking and laminating technology. For this purpose, the twisting protection and the bubbling prevention device, the automatic position adjustment controller, the visual sensors and the motor actuator for controller, the EMI shielding sheet cutting device and the main control system have been developed for manufacturing the apparatus. As the study result, the development on manufacturing the equipment and shielding sheet of the EMI shielding sheet of grid pattern for the wireless charger having the lamination productivity of 27.4m/min exceeded the target of 8m/min in this study. In addition, the magnetic induction and the applicable shielding sheet were prepared in the magnetic resonance system, all of the two wireless charging system. The power with a band of average 6.87MHz of shielding sheet was greater than the target of 30dB to 32.57dB. The available frequency with a band of average 7.95MHz the target was exceeded by a 7.00MHz.

The purpose of this study was to develop a grid forming equipment of the electromagenetic interference(EMI) shielding sheet for use in a wireless charger. In addition, the present study was to form a lattice in the surface of the thin metal ribbon to exert an electromagnetic wave shielding performance of the precision small electronic devices such as smart phones. For this, grid forming presses such as manual pressurized press, automatic pressurized press, heat pressurized press, and continuous grid forming equipment with cylinder roll type, and a grid inspection and grid uniformity inspection devices have been developed. Finally, the cylindrical roller-type continuous grid forming equipment showed the best suited.

This study concerns the integrated gas sensor system of wire and wireless communication by using IoT(Internet of Things) technology. First, communication part is that it delivers the detection information, which transferred by wire or wireless communication and required control procedure based on a wireless module that receives the gas leakage information from wired or wireless detector, to administrator or user’s terminal. Second, receiver part is that it shows the location and information, which received from the wired detector formed by a detecting sensor’s node as linking with the communication part, and transfers these to the communication part. Third, wireless detector formed as a communication module of a detecting sensor node is that it detects gas leakage and transfers the information through wireless as a packet.Fourth, wired detector communicated with the receiver part and formed as a communication module of a detecting sensor node is that it detects gas leakage, transfers and shows the information as a packet. Fifth, administrator’s terminal is that it receives gas leakage information by the communication part, transfers the signal by remote-control, and shut off a gas valve as responding the information. Sixth, database is that it is connected with the communication part; it sets and stores the default values for detecting smoke, CO., and temperature; it transfers this information to the communication part or sends a gas detecting signal to user’s terminal. Seventh, user’s terminal is that it receives each location’s default value which stored and set at the database; it manages emergency situation as shutting off a gas valve through remote control by corresponding each location’s gas leakage information, which transferred from the detector to the communication part by wireless.It is possible to process a high quality data regarding flammable or toxic gas by transferring the data, which measured by a sensor module of detector, to the communication part through wire and wireless. And, it allows a user to find the location by a smart phone where gas leaks. Eventually, it minimizes human life or property loss by having stability on gas leakage as well as corresponding each location’s information quickly.

The grid pattern electromagnetic interference(EMI) shielding sheet for the wireless charger has been designed using grid pattern metal sheet, PET & DST stacking and laminating technology. Also, an automatic manufacturing system of the grid pattern EMI shielding sheet for the wireless charger is developed. This metal sheet with grid pattern is an effective shield against EMI that can not shield completely by existing single metal sheet. And the developed automatic manufacturing system having a laminated productivity exceeds the 8m/min can stack and lamination thin metal sheets without any wrinkles.

기술 표준은 기술적 특성과 사양에 대한 일종의 사회적 합의로서 기술의 발달 과 함께 모든 산업에 걸쳐 존속되어 왔으며 최근에는 정보통신 기술의 발달과 함께 기술의 상호호환성을 제공하고 시장의 우위를 선점할 수 있는 전략적인 요소로 각광받고 있다. 이에 기술 표준 연구(표준화 연구)는 기술 표준의 채택 과정과 이로 인한 경제적 효과를 분석하여 이론적 및 정책적 함의를 도출하는데 그 의의가 있다. 그러나 기존의 연구에서는 기술 고유 의 가치와 상호호환성에 대한 고려가 부족하다는 점에서 기술 중심의 분석 결과를 도출하는 데 있어 구조적 한계를 드러낸다. 본 연구는 기술 네트워크 분석을 통해 도출한 기술 차별화 정도와 기업별 기술 선호도 함 수를 두 단계 게임 이론 분석 방법에 반영하여 새로운 기술 중심 표준 연구 방법론을 제공하는 것을 목적으로 하고 있다. 그 실증 사례로 사물인터넷의 무선 팬 기술을 선정하였으며, 본 연구 방법론을 통해 해당 시장의 기술 구조 및 표준 관련 함의를 도출하였다.

In these days, hazards in laboratories are consistently increasing due to high technological advance in modern science. Efforts to prevent accidents in laboratories became law named [ACT ON THE ESTABLISHMENT OF SAFE LABORATORY ENVIRONMENT]. The law made laboratories more safely but it’s not enough to keep up laboratory safety in advanced countries. To improve laboratory safety, this study reformed laboratory emergency response flow chart based on each emergency scenarios and its evaluated hazards in laboratories applied wireless hazard detecting equipments.

선박 및 해양구조물의 화물 중 많은 수가 가연성, 휘발성의 석유 및 석유 가공 화물이다. 뿐만 아니라 컨테이너 박스, 벌크화물, 차량 등의 중량 화물이 그 나머지를 차지한다. 게다가 선박은 파랑, 해류 등의 하중을 주기/비주기적으로 받기 때문에 화물의 위치 및 이동 가능성이 존재한다. 그렇기 때문에 선상 사고 위험은 육상의 산업현장 보다 훨씬 크다. 선박 및 해양구조물은 화물 및 화물의 영향으로 인한 사고 위험성이 항시 존재하기 때문에 그 모니터링과 대비가 반드시 필요하다. 이에 본 연구에서는 선상에서 선원 및 작업자의 안전을 보장하기 위해 무선센서네트워크를 도입하여 모니터링 시스템을 구축하기 위한 연구를 진행하였다.

Recently, though it was developed several services using the context-awareness technology of IoT, there exist also obstacles for high quality service. Specifically it is short the study for uncertainty of context-awareness. This study focused on understanding the effect of frequency interference among several environmental factors for location determination to increase precision of location determination. It was found that frequency interference between devices using 2.4Ghz frequency effect on the location determination precision. It was resulted that frequency interference increase the error of location determination precision. Then, we confirmed that it was required the suitable compensation method corresponding to frequency interference.

This paper describes the design and implementation of a electromagnetic energy harvesting mechanism and electronic circuit for autonomous emergency call system. This analysis results show the power output of the proposed harvesting mechanism and circuit up to max power output 5V and it can hold up to 65 msec of the power generation and 10msec of the RF transmission. Based on the these testing results, the implementation of autonomous emergency call device without battery power or any external power source is feasible.

PTEF membranes are used for roofing materials of membrane structures. PTEF is the abbreviation of Poly-tetra Fluotide-ethylene. These materials are consisted of fiberglass weave and polyetrfluoroethylene coating. Also, PTEF membranes have some problems of structural capacity by wind or snow load, etc. In this study, sensor housings using lead switches are bonding in PTFE membranes, Monitoring to changes tension and tear damages are studied using radio frequency. If tension is received on edged membranes, bonded lead switches of sensor housings will be destroyed by changes tension, and these become to send signals of damages at the connected radio frequency system with increased tension. Study of these functional membrane materials will be contributed to prevent water leakage and long-term maintenance of membrane structures.

This paper presents new type magnetostrictive optical systems. The suggested wireless optical systems are developed by using two types of magnetostrictive thin film actuators. The first is a seesaw type wireless-controlled compact optical switch, and another is a comb type TbDyFeNi thin film actuator by silicon micromachining techniques with DC magnetron sputtering. In the seesaw type, TbDyFe films are selectively deposited on the micromachined switch matrix. For the optical switching operation, switch is arranged in a 1×2 array (mirror size of 5mm × 800μm × 50μm) and has different length from the supporting point. Mirrors are also actuated by externally applied magnetic fields up to 0.5T. In the comb type, the effect of Ni content on the magneto-mechanical properties of the Tb0.24Dy0.76Fe2 system is investigated with the effect of deposited film thickness of TbDyFeNi on silicon substrate for wireless microactuator. As results, magneto-mechanical characteristics are investigated. using magnetization and deflected angle variation

본 연구에서 리드스위치를 이용한 정적변위센서를 무근과 철근 콘크리트 보에 부착하고 균열손상의 모니터링을 위해 무선주파수를 이용하였다. 무근 콘크리트 보와 철근 콘크리트 보에 외력이 작용하면 균열손상이 발생하고 균열의 증진으로 정적변위센서가 파괴되면 이와 연결되어 있는 무선주파수 발신자가 손상신호를 외부로 발신하게 된다. 이러한 기능성 건축부재에 대한 연구는 이상 기후 현상과 지진 등으로부터 건축물이나 주요구조물을 보호하는데 중요한 역할을 담당할 것으로 사료된다.

본 연구는 무인 항공사진 촬영을 이용하여 해안에 산재한 해안표착물을 탐지하는 새로운 방법을 제시하였다. 이동성과 신속성, 경제성이 우수한 소형 무선 조정 헬리콥터의 기체와 헬리콥터의 진동에 관계없이 연직 상태를 유지할 수 있는 짐벌 장치에 디지털카메라를 장착하여 항공사진 촬영을 시행하였다. 또한, 촬영된 영상으로부터 해안표착물을 탐지하기 위해 Matlab program을 이용한 디지털 영상처리 알고리즘을 고안하였다. 특히 고안된 알고리즘은 배경 차감 기법(Background subtraction method)을 적용하여 연구 대상 해안의 각기 다른 모래 상태로 인해 발생하는 물체 추출 오차를 감소시킴으로써 다양한 형태의 해안표착물을 안정적으로 탐지하는 결과를 보여주었다. 향후, 이 연구 방법을 적용한 해안표착물 모니터링이 이루어질 경우 모니터링 대상 구역 설정의 대표성 문제 해결 및 발생량 추정에 크게 기여할 수 있으며, 해양환경 감시 분야에 활용가능성이 클 것으로 판단된다.

케이블 구조시스템의 경우 자기 평형 상태를 유지하기 때문에 장력이 손실된 특정 케이블을 재긴장을 하지 않으면 구조엔지니어가 요구한 하중보다 더 큰 하중이 다른 케이블에 전달되어 손상을 야기 할 수 있다. 또한, 턴버클을 이용한 재긴장 방법이 기존에 널리 적용되고 있지만 정확한 장력조절과 대구경 케이블에는 적절하지 못하고 인장재의 하중의 크기를 측정하는 것이 어렵다. 따라서 효과적으로 재긴장 할 수 있는 유압식 볼팅 접합부를 개발하고 인장력을 실시간으로 확인할 수 있는 모니터링 시스템을 적용하였다. 본 논문에서는 개발된 시스템의 현장 적용성 실험과 결과를 제시하였다.

본 논문에서는 해상에서 사용 가능한 이중대역 무선랜 안테나를 설계하였다. 탄젠트 손실이 없는 FR-4기판을 사용하였으며, 유전율은 4.4, 32mm*28mm*1.6mm의 크기를 갖는다. 입력대비반사손실이 2.4GHz와 5.8GHz대역에서 -10dB이하로 동작하며 간단한 구성으로 50옴 마 이크로스트립라인에 의해 급전하는 안테나를 설계하여 양호한 반사손실을 보임을 확인하였다.