본 논문은 독거노인 또는 부정맥 환자의 24시간 응급감시 모니터링을 위해 광소자를 이용한 독거노인 위험감지형 맥박센서를 설계했다. 투과형의 광소자를 사용한 맥박 측정 센서는 상용 기술이지만, 이것은 의료 기관에서 환자나 환자 진료 모니터링을 위한 일회성 측정 방법이다. 때문에 일상생활에서 무구속의 지속적인 측정이 가능한 센서 개발이 필요하며, 또한 내구성과 편의성, 유동성에 대한 신뢰성과 안정성을 유지해야한다. 이러한 조건에서 우리는 손목시계 타입의 독거노인 위험감지형 맥박 센서를 설계하고, 실험 결과에서 그 가능성을 확인했다.

The aim of this study was to investigate microstructures and mechanical properties of nano-sized Ti-35 wt.%Nb-7 wt.%Zr-10 wt.%CPP composite fabricated by high energy mechanical milling (HEMM) and pulse current activated sintering (PCAS). Grain growth of the mechanically milled powder was prevented by performing PCAS. The principal advantages of calcium phosphate materials include: similarity in composition to the bone mineral, bioactivity, osteoconductivity and ability to form a uniquely strong interface with bone. The hardness and wear resistance property of nano-sized Ti-35 wt.%Nb-7 wt.%Zr-10 wt.%CPP composites increased with increasing milling time because of decreased grain-size of sintered composites.

Mono- and few-layer graphenes were grown on Ni thin films by rapid-thermal pulse chemical vapor deposition technique. In the growth steps, the exposure step for 60 s in H2 (a flow rate of 10 sccm (standard cubic centimeters per minute)) atmosphere after graphene growth was specially established to improve the quality of the graphenes. The graphene films grown by exposure alone without H2 showed an intensity ratio of IG/I2D = 0.47, compared with a value of 0.38 in the films grown by exposure in H2 ambient. The quality of the graphenes can be improved by exposure for 60 s in H2 ambient after the growth of the graphene films. The physical properties of the graphene films were investigated for the graphene films grown on various Ni film thicknesses and on 260-nm thick Ni films annealed at 500 and 700˚C. The graphene films grown on 260-nm thick Ni films at 900˚C showed the lowest IG/I2D ratio, resulting in the fewest layers. The graphene films grown on Ni films annealed at 700˚C for 2 h showed a decrease of the number of layers. The graphene films were dependent on the thickness and the grain size of the Ni films.

The phase Ti-Nb-Sn-HA bio materials were successfully fabricated by high energy mechanical milling and pulse current activated sintering (PCAS). Ti-6Al-4V ELI alloy has been widely used as biomaterial. But the Al has been inducing Alzheimer disease and V is classified as toxic element. In this study, ultra fine sized Ti-Nb-Sn-HA powder was produced by high energy mechanical milling machine. The phase Ti-Nb-Sn-HA powders were obtained after 12hr milling from phase. And ultra fine grain sized Ti-Nb-Sn-HA composites could be fabricated using PCAS without grain growth. After sintering, the microstructures and phase-transformation of Ti-Nb-Sn-HA biomaterials were analyzed by scanning electron microscope (SEM) and X-ray diffraction (XRD). The relative density was obtained by Archimedes principle and the hardness was measured by Vickers hardness tester. The -Ti phase was obtained after 12h milling. As result of hardness and relative density, 12h milled Ti-Nb-Sn-HA composite has the highest values.

Objectives: This research is about the reliability of pulse wave analyzer and heart rate variability analyzer which are often used in the oriental medical clinics. Materials and Methods: Pulse wave analyzer and heart rate variability analyzer's reliability were compared with other devices-bioelectrical impedance analyzer, thermographer and transcranial sonography-. For each device, they were measured three times in a row. Here are the results of measuring intraclass correlation coefficients between first and second, and the ones between first and third. Results: 1. For pulse wave analyzer, seven items are higher than 0.7 in intraclass correlation coefficients, fourteen items are higher than 0.5 and eleven items are higher than 0.5. 2. Heart rate variability analyzer show that an item is higher than 0.9 and two are higher than 0.7. three items are higher than 0.5 and four are lower than 0.5. 3. For bioelectrical impedance analyzer, thermographer and transcranial sonography, nineteen items are higher than 0.9 and two are higher than 0.7. Conclusion: Pulse wave analyzer and heart rate variability analyzer showed low test-retest reliability compared to the one of bioelectrical impedance analyzer, thermographer and transcranial sonography. But both of analyzer's reliability are more than midium quality. Diagnosis trough these analyzers have a utility value. More research will be needed. 

본 연구에서는 비침습적으로 압력 맥파를 검출하는 토노메트리 방식의 맥파 측정 장비인 SphygmoCor(AtCor, Australia)를 사용하여 측정자세에 따라 맥파를 측정하였다. 측정 결과를 통해 선 자세, 앉은 자세, 누운 자세에 따른 맥파의 분석 지표들의 변화를 분석하였다. 또한 측정된 데이터를 저혈압군, 정상혈압군, 고혈압군으로 구분하여 혈압군에 따른 맥파의 비교를 수행하였다. 그 결과 자세에 따른 요골동맥의 파형에서 유의차를 보인 분석지표는 맥파의 진폭에 해당되는 압력 보다 주요 피크가 발생되는 시간에서 나타났다. 맥압의 경우 맥파증대계수(AI)나 중심동맥압과 요골동맥압의 비율과 같이 맥압 간의 비율이 자세에 따른 변별력이 있었다. 사후검정에 따라 각 자세별로 상호 간에 모두 유의한 차이를 보인 분석지표는 주파(PT1)와 반사파(PT2)의 시간, 심박출지속시간(ED), 심박수(HR)로 나타났다. 혈압군에 대한 비교에서 대부분 맥파의 시간에 해당되는 지표보다 주요 피크의 진폭에 해당되는 맥파의 압력을 나타내는 지표가 혈압군에 따른 유의차를 보였다.

Micro-scale copper bumps for build-up PCB were electroplated using a pulse-reverse method. The effects of the current density, pulse-reverse ratio and brightener concentration of the electroplating process were investigated and optimized for suitable performance. The electroplated micro-bumps were characterized using various analytical tools, including an optical microscope, a scanning electron microscope and an atomic force microscope. Surface analysis results showed that the electroplating uniformity was viable in a current density range of 1.4-3.0 A/dm2 at a pulse-reverse ratio of 1. To investigate the brightener concentration on the electroplating properties, the current density value was fixed at 3.0 A/dm2 as a dense microstructure was achieved at this current density. The brightener concentration was varied from 0.05 to 0.3 ml/L to study the effect of the concentration. The optimum concentration for micro-bump electroplating was found to be 0.05 ml/L based on the examination of the electroplating properties of the bump shape, roughness and grain size.

Thermoelectric conversion efficiency of thermoelectric elements can be increased by using a structure combining n-type and p-type semiconductors. From the above point of view, attention was directed at ZnO as a candidate n-type semiconductor material and investigations were made. As the result, a dimensionless figure of merit ZT close to 0.28 (1073K) was obtained for specimens produced by the PCS (Pulse Current Sintering) method with addition of specified quantities of , CoO, and to ZnO. It was found that the interstitial in the ZnO restrains the grain growth and CoO acts onto the bond between grains. The influence of the inclusion of and CoO onto the sintering behavior also was investigated.

A connection between pulse-periodical laser radiation power and stability of liquid-metal contacts between powder particles during selective laser sintering (SLS) is determined based on analysis solving the problem of stability of liquid column in the gravity and capillary forces field. On the grounds of obtained relationships the optimization of pulse-periodical laser radiation power and SLS-process duration is realized, that allows to produce voluminous powder porous materials with pre-determined physical and mechanical properties and surface geometry. Results of metallographic investigations of powder porous materials of titanium powder produced with technological regimes calculated by means of obtained relationships are given in the work

The influence of porosity (P) on Young's modulus (E) and Poisson's ratio of sintered steels produced from four types of steel powders was investigated. The values of E and depend mainly on the value of P, and those were a little affected by alloying elements. The relationships between E, , and P were described as following equations: and , where subscript 0 means P = 0, and and are empirical constants. These approximate equations showed good agreement with empirical results.

War against Japanese(1592-1599) and war against Manchurian(1636-1637), which had been occurred in Korean Peninsula throughout the history, and frequent trade with foreign countries since 18th century have led to a distribution of foreign food into Korea. Several examples for this include tomato, apple, watermelon, maize, pea, cowpea, peanut, potato from China and red pepper, pumpkin, and sweet potato from Japan. Since these foods had been brought into Korea, they have been cultivated suitable for Korea's climate and land. Foreign foods with a few exceptions tend to have high calories. For instance, along with potato and sweet potato, pumpkin is considered a high-calorie food containing lots of starches as it becomes ripening. This helped a wide spread of the foreign foods across the nation where intake of high-calorie foods was critical for Korean people's nutrition at that time. Among those foods introduced from foreign countries, red pepper had a greatest impact on the dietary life-style of Chosun Dynasty. The use of red pepper has been greatly expanded from main ingredient to seasoning and garnishing in various forms of red pepper such as red pepper paste, red pepper powder, and thick soy paste mixed with red pepper. Red pepper was made eating habits is hot besides dye red colored to traditional food, because steaming and boiling is frequently cook method, fermentation food also food color is achromatic therefore food color is and mixture with red pepper, picked fish and chinese cabbage new kimchi culture came into being.

To evaluate parameters influencing on the dust removal of the High Temperature Filter(HTF) system, a computer simulation of fluid dynamics inside the system had been performed. The results showed that the optimum pulse jet periods were 50ms and 90ms for the 1000mm and 1500mm long filter elements respectively. Dust removal effect was very excellent under the pulse jet pressure of 3 bar. But the distance between the pulse jet nozzle and the venturi of a filter element had no meaningful effect on the performance with the variation from 5mm to 10mm. Compared to the dispersion mode of pulse jet, the collective mode of pulse jet flow was preferable in maintaining the pressure inside the system stable.