The citrus leaf miner (CLM) is an important citrus pest. A thorough understanding of the biology and population dynamics of CLM are essential for development of reliable pest population prediction system. We investigated the developmental periods of the species under ten constant temperature schemes (12.5℃~39℃). Furthermore, we established a development model of CLM, based on the result of a laboratory experiment. The immature developmental duration of CLM at constant temperatures were 63.5 days at 15℃, 23.9 days at 21℃, 15.6 days at 27℃, and 12.3 days at 33℃, showing statistically significant difference among temperature regimes. The lower threshold temperature and thermal constant were 11.3℃ and 243.7 DD, respectively, for immature development. In relation to temperature, non-linear development models were established for each developmental stage of CLM.

The purpose of this study is to determine the stiffness of rubber of dynamic damper. This damper system reduces the steering wheel vibration caused by idling oscillation of the engine. Therefore, in order to measure the stiffness of the silicone rubber in the dynamic damper system, the material test of the silicone rubber was carried out. Using the measured stiffness, the FEM model of the dynamic damper system was constructed and the correlation by the experimental data was shown at an error of less than 2%. In addition, the dynamic damper system was simplified to a two-degree-of-freedom spring-mass model and the effect of the stiffness change of the rubber on the natural frequency of the column shaft was analyzed theoretically. As a result, the amplitude of the column shaft was reduced as the stiffness of the silicone rubber was lowered.

A smart tuned mass damper (TMD) was developed to provide better control performance than a passive TMD for reduction of earthquake induced-responses. Because a passive TMD was developed decades ago, optimal design methods for structural parameters of a TMD, such as damping constant and stiffness, have been developed already. However, studies of optimal design method for structural parameters of a smart TMD were little performed to date. Therefore, parameter studies of structural properties of a smart TMD were conducted in this paper to develop optimal design method of a smart TMD under seismic excitation. A retractable-roof spatial structure was used as an example structure. Because dynamic characteristics of a retractable-roof spatial structure is changed based on opened or closed roof condition, control performance of smart TMD under off-tuning was investigated. Because mass ratio of TMD and smart TMD mainly affect control performance, variation of control performance due to mass ratio was investigated. Parameter studies of structural properties of a smart TMD was performed to find optimal damping constant and stiffness and it was compared with the results of optimal passive TMD design method. The design process developed in this study is expected to be used for preliminary design of a smart TMD for a retractable-roof spatial structure.

SiC-based composite materials with light weight, high durability, and high-temperature stability have been actively studied for use in aerospace and defense applications. Moreover, environmental barrier coating (EBC) technologies using oxide-based ceramic materials have been studied to prevent chemical deterioration at a high temperature of 1300℃ or higher. In this study, an ytterbium silicate material, which has recently been actively studied as an environmental barrier coating because of its high-temperature chemical stability, is fabricated on a sintered SiC substrate. Yb2O3 and SiO2 are used as the raw starting materials to form ytterbium disilicate (Yb2Si2O7). Suspension plasma spraying is applied as the coating method. The effect of the mixing method on the particle size and distribution, which affect the coating formation behavior, is investigated using a scanning electron microscope (SEM), an energy dispersive spectrometer (EDS), and X-ray diffraction (XRD) analysis. It is found that the originally designed compounds are not effectively formed because of the refinement and vaporization of the raw material particles, i.e., SiO2, and the formation of a porous coating structure. By changing the coating parameters such as the deposition distance, it is found that a denser coating structure can be formed at a closer deposition distance.

목 적 : 유방 MRI검사에서 회전 자장(B1)의 불균일성은 코일의 중심에 검사부위가 없고 우측과 좌측으로 나뉘어진 유방의 해부학적 구조의 영향을 많이 받는다. 또한 환자의 유방과 유방사이, 유방과 코일사이의 air-gap이 증가할수록 B1의 불균 일성도 증가하여 영상의 화질을 저하시킨다. 그러나 최근 유방암 환자의 증가에 따라 비대칭유방 환자 및 편측유방 등 small breast 환자들이 증가하고 있다. 이에 본 연구는 자체 제작한 phantom과 다양한 B1 calibration scan parameter를 이용하여 small breast에서 B1 calibration scan parameter의 변화에 대한 평가와 영상화질에 미치는 영향을 알아보고자 하였다. 대상 및 방법 : 검사 대상으로는 Invivo사의 breast phantom과 자체 제작 phantom을 이용하였다. 장비 사에서 권고하는 B1 calibration parameter가 최적의 조건을 나타내는지 평가하기 위한 대상으로 breast coil을 가득 채우는 Invivo사의 breast phantom을 사용하였고, 자체 제작 phantom을 이용하여 small breast일 때 최적의 B1 calibration parameter를 확인하였다. 연구에 사용된 장비는 Philips INGENIA 3.0T(Philips medical system, Netherlands)이고, 신호수집 코일은 16channel Breast coil을 사용하였다. 연구방법은 B1 calibration scan parameter 중 slice thickness(두께)를 5, 8, 12, 15, 20 mm로 Flip angle(FA)을 20, 40, 60, 80, 100 degree로 변화시켜가며 B1 map과 e-THRIVE 영상을 획득하였다. 정량적 평가로 획 득한 영상의 우측(Rt)과 좌측(Lt)에 각각 5개의 ROI를 그려 신호 대 잡음비(signal to noise ratio; SNR)를 비교 분석하였고 one-way ANOVA(SPSS 18.0K for windows)로 통계 검정하였다. 정성적 평가방법으로는 B1 map profile을 통해 B1의 균일성을 비교하였다. 결 과 : Invivo phantom으로 획득한 B1 map과 e-THRIVE 영상의 SNR은 B1 calibration scan parameter의 두께와 FA의 변화에 따라 차이가 있었다(P<0.001). 두께별 변화에서는 8 mm, FA별 변화에서는 60°일 때 가장 높게 나타났다. 자체 제작 phantom에서도 B1 map과 e-THRIVE 영상의 SNR은 B1 calibration scan parameter의 두께와 FA의 변화에 따라 차이가 있었다(P<0.001). 두 영상 모두 두께가 12mm 일 때 가장 높게 나타났으며, FA은 80°일 때 가장 높게 나타났다. B1 profile을 통해 확인한 자체 제작 phantom의 B1 균일도는 두께가 12 mm, FA이 80°일 때 가장 균등한 그래프를 나타냈다. 결 론 : 자체 제작 phantom의 B1 map 분석을 통해 장비사에서 권고된 parameter 변화의 필요성을 제고하고, 최적의 B1 calibration scan parameter를 확인할 수 있었다. 따라서 small breast 환자의 경우에는 B1 calibration scan parameter의 변 경이 필요하며, 이를 통해 SNR과 B1 균일성이 향상된 진단적 가치가 높은 유방 MRI영상을 얻을 수 있을 것이라 사료된다.

Pig has been known to be one of the most feasible animals as a bioreactor to produce pharmaceuticals in milk and as a mediator in xenotransplantation research. Previously, we generated transgenic pigs for both purposes, which were expressing Factor 8, vWF, hTPA, and hEPO in milk, along with expression of MCP at GalT gene locus (GalT-MCP/-MCP) as well as expressing MCP at GalT gene loci with CD73 expression (GalT-MCP/+/CD73). In this study, we performed comparative analyses of sperm parameters between wild type male (WT) pig and those transgenic males to examine the effects of transgenes integrated into the pigs on motility, morphology, viability, and acrosome integrity of the spermatozoa. Our results showed that the rates of actively motile spermatozoa of WT, Factor 8, vWF, hTPA, hEPO, GalT-MCP/+/CD73, and GalT-MCP/-MCP pigs were 85.0%, 83.3%, 82.5%, 83.3%, 82.5%, 77.5%, and 78.7%, respectively. Whereas, the rates of morphologically normal spermatozoa of WT, Factor 8, vWF, hTPA, hEPO, GalT-MCP/+/CD73, and GalT-MCP/-MCP pigs were 90.0%, 80.0%, 80.0%, 83.3%, 85.0%, 91.8%, and 80.8%, respectively. In addition, the viability in spermatozoa of WT, Factor 8, vWF, hTPA, hEPO, GalT-MCP/+/CD73, and GalT-MCP/-MCP pigs were 93.9%, 82.4%, 89.9%, 83.9%, 87.4%, 92.8%, and 83.6%, respectively. The rates of spermatozoa with normal acrosome integrity in WT, Factor 8, vWF, hTPA, hEPO, GalT-MCP/+/CD73, and GalT-MCP/-MCP pigs were 98.1%, 98.6%, 98.6%, 98.7%, 98.1%, 99.5%, and 95.1%, respectively. There were no significant differences in motility, morphology, viability, and acrosome integrity of the spermatozoa among WT, Factor 8, vWF, hTPA, and hEPO, GalT-MCP/+/CD73, and GalT-MCP/-MCP pigs. These mean that neither random integration nor targeted integration of the transgene into chromosome of pig effect on characteristics of spermatozoa. Ultimately, the transgenic male pigs subjected in this study could apply to propagate their progenies for production of human therapeutic proteins and advancing the xenotransplantation research.

The Kingery-Bulmash equation is the most common equation to calculate blast load. However, the Kingery-Bulmash equation is complicated. In this paper, a modified equation for surface blast load is proposed. The equation is based on Kingery-Bulmash equation. The proposed equation requires a brief calculation process, and the number of coefficients is reduced under 5. As a result, each parameter obtained by using the modified equation has less than 1% of error range comparing with the result by using Kingery-Bulmash equation. The modified equation may replace the original equation with brief process to calculate.

In this study, a winch and load motion control system design method is introduced. Especially, the winch and load (moving cart) are connected with long wire rope which is extended to few kilometers long. Therefore, the rope length changes such that many dynamic parameter values are changed as well by winding and releasing the rope from the winch system. In this paper, the authors designed the control system by considering the real time parameter variation to occupy and keep good control performance continuously. The effectiveness of introduced method was evaluated by simulation results.

본 연구의 목적은 한우 도체형질과 등심에 대한 일반성분(수분, 조지방, 조단백질, 조회분) 분석을 통 한 등심의 영양학적 가치와 유전모수 추정을 통한 개량형질 적용 가능성을 확인하기 위하여 실시하였 다. 본 연구에 이용된 공시 재료는 한우 후대검정우 47차부터 57차까지 실시한 2,033두에 대하여 등심 1㎏을 시료를 채취하여 분석한 자료를 이용하였다. 연구결과 한우 도체형질인 도체중, 등심단면적, 등 지방두께, 근내지방도에 대한 유전력은 각각 0.37, 0.51, 0.44, 0.57로 추정되었으며, 일반성분 분석인 수분, 조지방, 조단백질, 조회분에 대한 유전력은 각각 0.62, 0.64, 0.58, 0.12로 추정되었다. 그리고, 도체형질과 일반성분간의 유전상관은 도체중과 조지방에서 0.35, 근내지방도와 수분, 조지방, 조단백 질, 조회분에서 각각 -0.966, 0.964, -0.924, -0.664으로 고도의 유전상관을 보였다. 수분과 조지방, 조단백질간의 유전상관은 각각 -0.998, 0.969로 분석되었으며, 조지방과 조단백질에서 -0.979로 고도 의 유전상관을 보였다. 일반성분 분석치인 수분, 조지방, 조단백질에서 고도의 유전력을 보였으므로, 개 량형질 이용 가능성이 있을 것으로 사료된다.

Among the information technology and automation that have rapidly developed in the manufacturing industries recently, tens of thousands of quality variables are estimated and categorized in database every day. The former existing statistical methods, or variable selection and interpretation by experts, place limits on proper judgment. Accordingly, various data mining methods, including decision tree analysis, have been developed in recent years. Cart and C5.0 are representative algorithms for decision tree analysis, but these algorithms have limits in defining the tolerance of continuous explanatory variables. Also, target variables are restricted by the information that indicates only the quality of the products like the rate of defective products. Therefore it is essential to develop an algorithm that improves upon Cart and C5.0 and allows access to new quality information such as loss cost. In this study, a new algorithm was developed not only to find the major variables which minimize the target variable, loss cost, but also to overcome the limits of Cart and C5.0. The new algorithm is one that defines tolerance of variables systematically by adopting 3 categories of the continuous explanatory variables. The characteristics of larger-the-better was presumed in the environment of programming R to compare the performance among the new algorithm and existing ones, and 10 simulations were performed with 1,000 data sets for each variable. The performance of the new algorithm was verified through a mean test of loss cost. As a result of the verification show, the new algorithm found that the tolerance of continuous explanatory variables lowered loss cost more than existing ones in the larger is better characteristics. In a conclusion, the new algorithm could be used to find the tolerance of continuous explanatory variables to minimize the loss in the process taking into account the loss cost of the products.1)

Carboxylated multi-wall carbon nanotubes (MWCNTs-COOH) have been used as efficient adsorbents for the removal of picric acid from aqueous solutions under stirring and ultrasound conditions. Batch experiments were conducted to study the influence of the different parameters such as pH, amount of adsorbents, contact time and concentration of picric acid on the adsorption process. The kinetic data were fitted with pseudo-first order, pseudo-secondorder, Elovich and intra-particle diffusion models. The kinetic studies were well described by the pseudo-second-order kinetic model for both methods. In addition, the adsorption isotherms of picric acid from aqueous solutions on the MWCNTs were investigated using six two-parameter models (Langmuir, Freundlich, Tempkin, Halsey, Harkins-Jura, Fowler- Guggenheim), four three-parameter models (Redlich-Peterson, Khan, Radke-Prausnitz, and Toth), two four-parameter equations (Fritz-Schlunder and Baudu) and one five-parameter equation (Fritz-Schlunder). Three error analysis methods, correlation coefficient, chi-square test and average relative errors, were applied to determine the best fit isotherm. The error analysis showed that the models with more than two parameters better described the picric acid sorption data compared to the two-parameter models. In particular, the Baudu equation provided the best model for the picric acid sorption data for both methods.

This research focused on deciding optimal manufacturing WIP (Work-In-Process) limit for a small production system. Reducing WIP leads to stable capacity, better manufacturing flow and decrease inventory. WIP is the one of the important issue, since it can affect manufacturing area, like productivity and line efficiency and bottlenecks in manufacturing process. Several approaches implemented in this research. First, two strategies applied to decide WIP limit. One is roulette wheel selection and the other one is elite strategy. Second, for each strategy, JIT (Just In Time), CONWIP (Constant WIP), Gated Max WIP System and CWIPL (Critical WIP Loops) system applied to find a best material flow mechanism. Therefore, pull control system is preferred to control production line efficiently. In the production line, the WIP limit has been decided based on mathematical models or expert’s decision. However, due to the complexity of the process or increase of the variables, it is difficult to obtain optimal WIP limit. To obtain an optimal WIP limit, GA applied in each material control system. When evaluating the performance of the result, fitness function is used by reflecting WIP parameter. Elite strategy showed better performance than roulette wheel selection when evaluating fitness value. Elite strategy reach to the optimal WIP limit faster than roulette wheel selection and generation time is short. For this reason, this study proposes a fast and reliable method for determining the WIP level by applying genetic algorithm to pull system based production process. This research showed that this method could be applied to a more complex production system.

This paper is concerned with a test method that can be used to investigate the parameters of the Johnson-Cook constitutive model. These parameters are essential for accurately analyzing material behavior under impact loading conditions in numerical simulation. Ti-6Al-4V alloy (HCP crytal structure) was used as a specimen for the experiments. In the 10−3-103/ s strain rate range, three types of experimental methods (convention, compression and tension) were employed to compare the differences using MTS-810, SHPB and SHTB. Finite element analysis results when applying these parameters were displayed along with the experiment results.

The blast load is classified into free-air blast and surface blast following the location of explosion and surface. In this paper, several equations for blast load calculation are explained briefly and a modified equation for free-air blast load is suggested. The modified equation is based on Kingery-Bulmash equation which is used in UFC 3-340-02 and Conwep model. In this modified equation, the process of calculation is simplified against the original equation, and the number of coefficients is reduced under 5. As a result, each parameter of estimated data by modified equation has less than 1% of error range comparing with Kingery-Bulmash equation.

PVDF Membrane has been used as material for the UF membrane through in-situ interfacial polymerization (IP) because of it’s outstanding properties such as high chemical resistance, thermal stability, and mechanical strength. In this study, surface morphology change of PVDF membrane was researched depending on evaporation time. 13% PVDF 6020 was used for casting and the evaporation time period was from 5s to 600s. The surface morphology of the membrane was investigated by scanning electron microscopy (SEM) and filtration was conducted in the cross flow method to evaluate the a performance of UF membrane. As a result, average pore size was increased with longer evaporation times which caused the decrease of rejection.

This study aimed to find the optimum instrumental test conditions for the Texture Profile Analysis (TPA) of cooked rice in order to predict the sensory texture attributes (hardness, adhesiveness, chewiness). Sensory evaluation was performed for three kinds of instant cooked rice with university students in their twenties and the results of the sensory evaluation were compared to instrumental TPA patterns. Using partial least squares regression, the instrumental TPA results at a cross-head speed of 1.0 mm/sec and a compression ratio of 70% proved to be an excellent predictor of the sensory attributes of hardness (R2=0.99) and chewiness (R2=0.99). The results at a cross-head speed of 0.5 mm/sec and compression ratio of 30% provided an excellent model for the prediction of sensory adhesiveness (R2=0.83). In this experimental range, sensory hardness and chewiness showed a high correlation with instrumental TPA parameters (hardness, cohesiveness, adhesiveness, springiness, chewiness) with a high cross-head speed and compression ratio, while sensory adhesiveness showed a high correlation with the TPA parameters with a low cross-head speed and compression ratio.

The objective of this study was to determine the effect of drinking water containing trimethyl glycine or ascorbic acid on growth performance and blood parameter profiles of duck exposed to scorching heat stress. A total of 480 ducks were randomly assigned to the following eight experiment groups for 42 days : control group C with general water, treatment group 1 (T1) with drinking water containing 100 ppm ascorbic acid, treatment group 2 (T2) with drinking water containing 200 ppm ascorbic acid, treatment group 3 (T3) with drinking water containing 300 ppm ascorbic acid, treatment group 4 (T4) with drinking water containing 400 ppm trimethyl glycine, treatment group 5 (T5) with drinking water containing 800 ppm trimethyl glycine, treatment group 6 (T6) with drinking water containing 1,200 ppm trimethyl glycine, treatment group 7 (T7) with electrolytes of KCl (0.5%) + NaHCO3 (1.0%)+NaCl (0.5%). Our results revealed that the body weights and feed intakes of treatment groups, especially T3 and T6, were increased compared to the control group, where as the feed conversion ratios of treatment groups were decreased (p<0.05). Blood levels of total cholesterol, triglyceride, LDL-C, glucose, AST, ALT and pH in treatment groups were lower compared to those in the control group (p<0.05). Blood levels of red blood cell, platelets profiles, electrolyte and gas in treatment groups were higher compared to those of the control group (p<0.05).

The purpose of this study is to understand how to affect the safety behavior to the organization's trustees to investigate the level of safety awareness, safety awareness via the distribution center workers prepare the logistics industry disaster prevention measures. The survey was analyzed data to target by the clothing distribution center employees of 182 people. Analysis First, the level of safety awareness showed on a positive effect on organization trust. Second, it was found on the safety level of consciousness a positive effect on the safety behavior. Third, the level of safety awareness affect the safety behavior showed that the mediating role of organization trust. That is a higher level of safety awareness, such as the strict practice of business activities, investments, safety rules on safety education and training emphasis on safety increases confidence in the organization. It was confirmed the higher the confidence in the safety organization appears behavior such as actively participating in the work carried out in a safe manner, safety education and training. In addition, the effect was mediated by the organizational impact on confidence in the safety of personnel safety awareness actions. Based on that research results prepared safety awareness was raised through the industrial accident prevention measures

This study investigates on the tuning stainless steel(STS630) to understand for groove cutting characteristics. For this purpose, we observed the cutting force according to feed rate and cutting speed variation and performed the computational analysis due to groove cutting depth. In groove cutting of stainless steel, there were principal force, feed force and radial force by arranging the highest cutting force in order. In case of wall thicknesses of 0.3mm and 0.5mm at groove cutting, principal force increases according to the increase of feed rate but it is not related to cutting speed. We found the unstable region of cutting force that is caused to the friction resistance of cutting tool and elastic deformation of groove wall. In computational analysis, we confirmed that the more feed rate increases, the more strain increases around the tooth root.